Elastomer-Embedded Multiplexed Optical Fiber Sensor System for Multiplane Shape Reconstruction

This paper presents the development and application of a multiplexed intensity variation-based sensor system for multiplane shape reconstruction. The sensor is based on a polymer optical fiber (POF) with sequential lateral sections coupled with a flexible light-emitting diode (LED) belt. The optical source modulation enables the development of 30 independent sensors using one photodetector, where the sensor system is embedded in polydimethylsiloxane (PDMS) resin in two configurations. Configuration 1 is a continuous PDMS layer applied in the interface between the flexible LED belt and the POF, whereas Configuration 2 comprises a 20 mm length PDMS layer only on each lateral section and LED region. The finite element method (FEM) is employed for the strain distribution evaluation in different conditions, including the strain distribution on the sensor system subjected to momentums in roll, pitch and yaw conditions. The experimental results of pressure application at 30 regions for each configuration indicated a higher sensitivity of Configuration 1 (83.58 a.u./kPa) when compared with Configuration 2 (40.06 a.u./kPa). However, Configuration 2 presented the smallest cross-sensitivity between sequential sensors (0.94 a.u./kPa against 45.5 a.u./kPa of Configuration 1). Then, the possibility of real-time loading condition monitoring and shape reconstruction is evaluated using Configuration 1 subjected to momentums in roll, pitch and yaw, as well as mechanical waves applied on the sensor structure. The strain distribution on the sensor presented the same pattern as the one obtained in the simulations, and the real-time response of each sensor was obtained for each case. In addition, the possibility of real-time loading condition estimation is analyzed using the k-means algorithm (an unsupervised machine learning approach) for the clusterization of data regarding the loading condition. The comparison between the predicted results and the real ones shows a 90.55% success rate. Thus, the proposed sensor device is a feasible alternative for integrated sensing in movement analysis, structural health monitoring submitted to dynamic loading and robotics for the assessment of the robot structure.

Direct Bragg Grating Inscription in Single Mode Step-Index TOPAS/ZEONEX Polymer Optical Fiber Using 520 nm Femtosecond Pulses

We experimentally report fiber Bragg gratings (FBGs) in a single mode step-index polymer optical fiber (POF) with a core made of TOPAS and cladding made of ZEONEX using 520 nm femtosecond pulses and a point-by-point (PbP) inscription method. With different pulse energies between 9.7 nJ and 11.2 nJ, 12 FBGs are distributed along the cores of two pieces of POFs with negative averaged effective index change up to ~6 × 10⁻⁴ in the TOPAS. For POF 1 with FBGs 1–6, the highest reflectivity 45.1% is obtained with a pulse energy of 10.6 nJ. After inscription, good grating stability is reported. Thanks to the post-annealing at 125 °C for 24 h, after cooling the grating reflectivity increases by ~10%. For POF 2 with FBGs 7–12, similar FBG data are obtained showing good reproducibility. Then, the FBGs are annealed at 125 °C for 78 h, and the average reflectivity of the FBGs during the annealing process increases by ~50% compared to that before the annealing, which could be potentially applied to humidity insensitive high temperature measurement.

Experimental Assessment of the Transmission Performance of Step Index Polymer Optical Fibers Using a Green Laser Diode

Large-core polymer optical fiber (POF) links have limitations in capacity and reach due to the fibers’ high modal dispersion and attenuation. Most of these links use red laser diodes, even though the attenuation spectrum of poly(methyl methacrylate) (PMMA), the basic polymer used to manufacture these fibers, has a lower minimum in the green region. Therefore, we set out to explore the potential use of green light in transmission systems, comparing the performances of three step-index polymer optical fibers (SI-POFs) with different numerical apertures. We obtained measurements of intensity distribution, frequency response and bit error rate (BER), as functions of fiber length. We have also compared the fibers’ frequency responses with red and green light for a few selected lengths. Our results confirm that SI-POFs attenuate less in response to green light, which can increase their length. This advantage is partially counterbalanced by a slightly higher dispersion that limits the capacity of the high-aperture fibers, particularly at relatively short lengths. Our conclusions are critical to understanding SI-POF behavior and to designing thorough SI-POF models that can aid the design of POF-based links for different scenarios.

Distributed Static and Dynamic Strain Measurements in Polymer Optical Fibers by Rayleigh Scattering

We demonstrate the use of a graded-index perfluorinated optical fiber (GI-POF) for distributed static and dynamic strain measurements based on Rayleigh scattering. The system is based on an amplitude-based phase-sensitive Optical Time-Domain Reflectometry (ϕ-OTDR) configuration, operated at the unconventional wavelength of 850 nm. Static strain measurements have been carried out at a spatial resolution of 4 m and for a strain up to 3.5% by exploiting the increase of the backscatter Rayleigh coefficient consequent to the application of a tensile strain, while vibration/acoustic measurements have been demonstrated for a sampling frequency up to 833 Hz by exploiting the vibration-induced changes in the backscatter Rayleigh intensity time-domain traces arising from coherent interference within the pulse. The reported tests demonstrate that polymer optical fibers can be used for cost-effective multiparameter sensing.

Challenges in the Fabrication of Biodegradable and Implantable Optical Fibers for Biomedical Applications

The limited penetration depth of visible light in biological tissues has encouraged researchers to develop novel implantable light-guiding devices. Optical fibers and waveguides that are made from biocompatible and biodegradable materials offer a straightforward but effective approach to overcome this issue. In the last decade, various optically transparent biomaterials, as well as different fabrication techniques, have been investigated for this purpose, and in view of obtaining fully fledged optical fibers. This article reviews the state-of-the-art in the development of biocompatible and biodegradable optical fibers. Whilst several reviews that focus on the chemical properties of the biomaterials from which these optical waveguides can be made have been published, a systematic review about the actual optical fibers made from these materials and the different fabrication processes is not available yet. This prompted us to investigate the essential properties of these biomaterials, in view of fabricating optical fibers, and in particular to look into the issues related to fabrication techniques, and also to discuss the challenges in the use and operation of these optical fibers. We close our review with a summary and an outline of the applications that may benefit from these novel optical waveguides.

Effects of Fabrication Methods on the Performance of Luminescent Solar Concentrators Based on Doped Polymer Optical Fibers

In this work, we detail two types of fabrication processes of four polymer optical fibers doped with lumogen dyes. The fiber preforms have been manufactured with two different methods: extrusion and casting. We have compared the performance of the two types of fibers as luminescent solar concentrators by calculating their optical efficiencies and concentration factors. The obtained results show better performance for those fibers manufactured by the casting process. We have also studied the photostability of the two types of fibers doped with the dye lumogen red under solar light radiation. A high thermal stability of the doped fibers has been observed.

Polycarbonate mPOF-Based Mach-Zehnder Interferometer for Temperature and Strain Measurement

In this paper, an endlessly single mode microstructured polymer optical fiber (mPOF) in a Mach–Zehnder (M–Z) interferometer configuration is demonstrated for temperature and strain measurement. Because there is no commercial splicer applied for POF-silica optical fiber (SOF) connectorization, prior to the M–Z interferometric sensing, we introduce an imaging projecting method to align a polycarbonate mPOF to a SOF and then the splice is cured permanently using ultraviolet (UV) glue. A He-Ne laser beam at 632.8 nm coupled in a SOF is divided by a 1 × 2 fiber coupler to propagate in two fiber arms. A piece of mPOF is inserted in one arm for sensing implementation and the interference fringes are monitored by a camera. For non-annealed fiber, the temperature sensitivity is found to be 25.5 fringes/°C for increasing temperature and 20.6 fringes/°C for decreasing temperature. The converted sensitivity per unit length is 135.6 fringes/°C/m for increasing temperature, which is twice as much as the silica fiber, or 852.2 rad/°C/m (optical phase change versus fiber temperature), which is more than four times as much as that for the PMMA fiber. To solve the sensitivity disagreement, the fiber was annealed at 125 °C for 36 h. Just after the thermal treatment, the temperature measurement was conducted with sensitivities of 16.8 fringes/°C and 21.3 fringes/°C for increasing and decreasing process, respectively. One month after annealing, the linear response was improved showing a temperature sensitivity of ~20.7 fringes/°C in forward and reverse temperature measurement. For the strain measurement based on non-annealed fiber, the sensitivity was found to be ~1463 fringes/%ε showing repeatable linear response for forward and reverse strain. The fiber axial force sensitivity was calculated to be ~2886 fringes/N, showing a force measurement resolution of ~3.47 × 10⁻⁴ N. The sensing methodology adopted in this work shows several advantages, such as very low cost, high sensitivity, a straightforward sensing mechanism, and ease of fabrication.

Annular Cavity Design for Photoluminescent Polymer Optical Fiber Sensors

We present optimization results on the design of a polymer optical fiber single point sensor suitable for photoluminescence-based sensing. The single point sensing design consists of one or two annular cavities, separated by a small distance, milled into the fiber and subsequently filled with a thick solution of polymer, solvent, and photoluminescent molecules, which is then allowed to dry. The design is tested by varying the depth and length of a single cavity and utilizing two cavities with varying separations. Results from experiments show a maximum response at a separation of 2 mm for which we present an analytical explanation. A geometrical, numerical simulation model, taking into account both skew and meridional rays, is developed and shows very good agreement with the experimental results. The fiber design presents a general platform that has the potential for the fabrication of multi-point photoluminescent sensors, for which it is necessary to have several points along the fiber functionalized for sensing. Furthermore, the approach with polymer fibers and polymer sensing gels allows for a robust integration of the sensing matrix and the optical fiber, more so than is possible using glass optical fibers.

Polymer Fibers Covered by Soft Multilayered Films for Sensing Applications in Composite Materials

This paper presents the possibility of applying a soft polymer coating by means of a layer-by-layer (LbL) technique to highly birefringent polymer optical fibers designed for laminating in composite materials. In contrast to optical fibers made of pure silica glass, polymer optical fibers are manufactured without a soft polymer coating. In typical sensor applications, the absence of a buffer coating is an advantage. However, highly birefringent polymer optical fibers laminated in a composite material are much more sensitive to temperature changes than polymer optical fibers in a free space as a result of the thermal expansion of the composite material. To prevent this, we have covered highly birefringent polymer optical fibers with a soft polymer coating of different thickness and measured the temperature sensitivity of each solution. The results obtained show that the undesired temperature sensitivity of the laminated optical fiber decreases as the thickness of the coating layer increases.

Characterization of Double-Doped Polymer Optical Fibers as Luminescent Solar Concentrators

This work reports on a diameter dependence analysis of the performance as luminescent solar concentrators of three self-fabricated polymer optical fibers (POFs) doped with a hybrid combination of dopants. The works carried out include the design and self-fabrication of the different diameter fibers; an experimental analysis of the output power, of the output irradiance and of the fluorescent fiber solar concentrator efficiency; a comparison of the experimental results with a theoretical model; a study of the performance of all the fibers under different simulated lighting conditions; and a calculation of the active fiber length of each of the samples, all of them as a function of the fiber core diameter. To the best of our knowledge, this paper reports the first analysis of the influence of the POF diameter for luminescent solar concentration applications. The results obtained offer a general perspective on the optimal design of solar energy concentrating systems based on doped POFs and pave the way for the implementation of cost-effective solar energy concentrating devices.

Fabrication of Active Polymer Optical Fibers by Solution Doping and Their Characterization

This paper employs the solution-doping technique for the fabrication of active polymer optical fibers (POFs), in which the dopant molecules are directly incorporated into the core of non-doped uncladded fibers. Firstly, we characterize the insertion of a solution of rhodamine B and methanol into the core of the fiber samples at different temperatures, and we show that better optical characteristics, especially in the attenuation coefficient, are achieved at lower temperatures. Moreover, we also analyze the dependence of the emission features of doped fibers on both the propagation distance and the excitation time. Some of these features and the corresponding ones reported in the literature for typical active POFs doped with the same dopant are quantitatively similar among them. This applies to the spectral location of the absorption and the emission bands, the spectral displacement with propagation distance, and the linear attenuation coefficient. The samples prepared in the way described in this work present higher photostability than typical samples reported in the literature, which are prepared in different ways.

U-Shaped and Surface Functionalized Polymer Optical Fiber Probe for Glucose Detection

In this work we show an optical fiber evanescent wave absorption probe for glucose detection in different physiological media. High selectivity is achieved by functionalizing the surface of an only-core poly(methyl methacrylate) (PMMA) polymer optical fiber with phenilboronic groups, and enhanced sensitivity by using a U-shaped geometry. Employing a supercontinuum light source and a high-resolution spectrometer, absorption measurements are performed in the broadband visible light spectrum. Experimental results suggest the feasibility of such a fiber probe as a low-cost and selective glucose detector.

Optical Characterization of Doped Thermoplastic and Thermosetting Polymer-Optical-Fibers

The emission properties of a graded-index thermoplastic polymer optical fiber and a step-index thermosetting one, both doped with rhodamine 6G, have been studied. The work includes a detailed analysis of the amplified spontaneous emission together with a study of the optical gains and losses of the fibers. The photostability of the emission of both types of fibers has also been investigated. Comparisons between the results of both doped polymer optical fibers are presented and discussed.

Fabrication and characterization of disordered polymer optical fibers for transverse Anderson localization of light

We develop and characterize a disordered polymer optical fiber that uses transverse Anderson localization as a novel waveguiding mechanism. The developed polymer optical fiber is composed of 80,000 strands of poly (methyl methacrylate) (PMMA) and polystyrene (PS) that are randomly mixed and drawn into a square cross section optical fiber with a side width of 250 μm. Initially, each strand is 200 μm in diameter and 8-inches long. During the mixing process of the original fiber strands, the fibers cross over each other; however, a large draw ratio guarantees that the refractive index profile is invariant along the length of the fiber for several tens of centimeters. The large refractive index difference of 0.1 between the disordered sites results in a small localized beam radius that is comparable to the beam radius of conventional optical fibers. The input light is launched from a standard single mode optical fiber using the butt-coupling method and the near-field output beam from the disordered fiber is imaged using a 40X objective and a CCD camera. The output beam diameter agrees well with the expected results from the numerical simulations. The disordered optical fiber presented in this work is the first device-level implementation of 2D Anderson localization, and can potentially be used for image transport and short-haul optical communication systems.