3D mapping of polymerization shrinkage using X-ray micro-computed tomography to predict microleakage

OBJECTIVES

The objectives of this study were to (1) demonstrate X-ray micro-computed tomography (microCT) as a viable method for determining the polymerization shrinkage and microleakage on the same sample accurately and non-destructively, and (2) investigate the effect of sample geometry (e.g., C-factor and volume) on polymerization shrinkage and microleakage.

METHODS

Composites placed in a series of model cavities of controlled C-factors and volumes were imaged using microCT to determine their precise location and volume before and after photopolymerization. Shrinkage was calculated by comparing the volume of composites before and after polymerization and leakage was predicted based on gap formation between composites and cavity walls as a function of position. Dye penetration experiments were used to validate microCT results.

RESULTS

The degree of conversion (DC) of composites measured using FTIR microspectroscopy in reflectance mode was nearly identical for composites filled in all model cavity geometries. The shrinkage of composites calculated based on microCT results was statistically identical regardless of sample geometry. Microleakage, on the other hand, was highly dependent on the C-factor as well as the composite volume, with higher C-factors and larger volumes leading to a greater probability of microleakage. Spatial distribution of microleakage determined by microCT agreed well with results determined by dye penetration.

SIGNIFICANCE

microCT has proven to be a powerful technique in quantifying polymerization shrinkage and corresponding microleakage for clinically relevant cavity geometries.

Dental composites based on amorphous calcium phosphate - resin composition/physicochemical properties study

This study explores how the resin composition/structure affects the physicochemical properties of copolymers and their amorphous calcium phosphate (ACP)-filled composites. A series of photo-polymerizable binary and ternary matrices are formulated utilizing 2,2-bis[ p-(2(')-hydroxy-3(')methacryloxypropoxy)phenyl]propane, 2,2-bis[ p-(2(')-methacryloxypropoxy)phenyl]-propane (EBPADMA), or a urethane dimethacrylate as base monomers, and triethylene glycol dimethacrylate or hexamethylene dimethacrylate (HmDMA) with or without 2-hydroxyethyl methacrylate (HEMA) as diluent monomer. Unfilled copolymers and composites filled with 40% by mass zirconia-hybridized ACP are evaluated for biaxial flexure strength (BFS), degree of conversion (DC), mineral ion release, polymerization shrinkage (PS), and water sorption (WS). The average DC values are 82-94% and 74-91% for copolymers and composites, respectively. Unrelated to the resin composition, the PS values of composites are up to 8.4 vol. % and the BFS values of wet composite specimens are on average 51 +/- 8 MPa. The maximum WS values attained in copolymers and composites reach 4.8 mass%. Inclusion of hydrophobic HmDMA monomer in the matrices significantly reduces the WS. The levels of Ca and PO(4) released from all types of composites are significantly above the minimum necessary for the re-deposition of apatite to occur. Elevated Ca, and to a lesser extent PO(4) release, is observed in HEMA-containing, ternary EBPADMA formulations. Further resin reformulations may be needed to improve the PS of composite specimens. Poor dispersion of ;as-synthesized' ACP within the composite contributes to their inferior mechanical performance.

Evaluation of dental composite shrinkage and leakage in extracted teeth using X-ray microcomputed tomography

OBJECTIVE

Use X-ray microcomputed tomography (microCT), to test the hypothesis that composite shrinkage and sites of potential leakage in human teeth are non-uniformly distributed and depend on cavity geometry and C-factor.

METHODS

Two holes of equal volume but different dimensions were drilled into the exposed dentin of extracted human molars. The cavities were filled with composite and teeth were scanned, before and after curing, using microCT. Three-dimensional (3D) reconstructions of the data were prepared and analyzed using image analysis software.

RESULTS

3D reconstructions showed that cavity geometry did not affect the polymerization shrinkage. The shrinkage for all restorations was 2.66+/-0.59%, and cavity dimensions did not affect the volume lost, either in quantity or location on the sample. Potential leakage sites were identified by gap formations and found to be non-uniformly distributed along the tooth-composite interface. Leakage in regions calculated by microCT was confirmed by visualization of sectioned samples with confocal laser scanning microscopy.

SIGNIFICANCE

microCT evaluation will add tremendous value as part of a suite of tests to characterize various properties of dental materials. The non-uniform distribution of potential leakage sites about the cavities that was determined by microCT emphasizes the inadequacy of traditional methods of determining leakage, which are capable of analyzing only limited areas. Additionally, microCT evaluation can produce quantitative analyses of shrinkage and leakage, compared to the conventional methods, which are qualitative or semi-quantitative. Finally, experimentally determined shrinkage and leakage of composite in extracted teeth agrees with the results of similar experiments in model cavities, confirming the validity of those models.

The use of different adhesive filling material and mass combinations to restore class II cavities under loading and shrinkage effects: a 3D-FEA

3D tooth models were virtually restored: flowable composite resin + bulk-fill composite (A), glass ionomer cement + bulk-fill composite (B) or adhesive + bulk-fill composite (C). Polymerization shrinkage and masticatory loads were simulated. All models exhibited the highest stress concentration at the enamel-restoration interfaces. A and C showed similar pattern with lower magnitude in A in comparison to C. B showed lower stress in dentine and C the highest cusps displacement. The use of glass ionomer cement or flowable composite resin in combination with a bulk-fill composite improved the biomechanical behavior of deep class II MO cavities.

Novel Urethane-Dimethacrylate Monomers and Compositions for Use as Matrices in Dental Restorative Materials

In this study, novel urethane-dimethacrylate monomers were synthesized from 1,3-bis(1-isocyanato-1-methylethyl)benzene (MEBDI) and oligoethylene glycols monomethacrylates, containing one to three oxyethylene groups. They can potentially be utilized as matrices in dental restorative materials. The obtained monomers were used to prepare four new formulations. Two of them were solely composed of the MEBDI-based monomers. In a second pair, a monomer based on triethylene glycol monomethacrylate, used in 20 wt.%, was replaced with triethylene glycol dimethacrylate (TEGDMA), a reactive diluent typically used in dental materials. For comparison purposes, two formulations, using typical dental dimethacrylates (bisphenol A glycerolate dimethacrylate (Bis-GMA), urethane-dimethacrylate (UDMA) and TEGDMA) were prepared. The monomers and mixtures were tested for the viscosity and density. The homopolymers and copolymers, obtained via photopolymerization, were tested for the degree of conversion, polymerization shrinkage, water sorption and solubility, hardness, flexural strength and modulus. The newly developed formulations achieved promising physico-chemical and mechanical characteristics so as to be suitable for applications as dental composite matrices. A combination of the MEBDI-based urethane-dimethacrylates with TEGDMA resulted in copolymers with a high degree of conversion, low polymerization shrinkage, low water sorption and water solubility, and good mechanical properties. These parameters showed an improvement in relation to currently used dental formulations.

Moving Towards a Finer Way of Light-Cured Resin-Based Restorative Dental Materials: Recent Advances in Photoinitiating Systems Based on Iodonium Salts

The photoinduced polymerization of monomers is currently an essential tool in various industries. The photopolymerization process plays an increasingly important role in biomedical applications. It is especially used in the production of dental composites. It also exhibits unique properties, such as a short time of polymerization of composites (up to a few seconds), low energy consumption, and spatial resolution (polymerization only in irradiated areas). This paper describes a short overview of the history and classification of different typical monomers and photoinitiating systems such as bimolecular photoinitiator system containing camphorquinone and aromatic amine, 1-phenyl-1,2-propanedione, phosphine derivatives, germanium derivatives, hexaarylbiimidazole derivatives, silane-based derivatives and thioxanthone derivatives used in the production of dental composites with their limitations and disadvantages. Moreover, this article represents the challenges faced when using the latest inventions in the field of dental materials, with a particular focus on photoinitiating systems based on iodonium salts. The beneficial properties of dental composites cured using initiation systems based on iodonium salts have been demonstrated.

Microleakage evaluation of silorane based composite versus methacrylate based composite

AIM

Our study aimed to analyze the microleakage of silorane-based composite in comparison to two homologous methacrylate-based composites.

MATERIALS AND METHODS

Standardized class I cavities (4 × 2.5 × 3 mm) were prepared on extracted human premolars and randomly assigned into three groups (N = 15) as follows: Group A, Filtek P90 (silorane) with its dedicated adhesive system (P90 system adhesive); Group B, Adper SE Plus with Filtek Z250; Group C, Peak SE with Amelogen Plus. The teeth were subjected to thermocycling regime (200×, 5-55°C) and dye penetration of tooth sections were evaluated following 30 minute immersion in 2% Methylene Blue dye. Statistical analysis was performed with Kruskal-Wallis and Mann-Whitney U test at 95% significance level.

RESULTS

Silorane exhibited significantly decreased microleakage compared with any other resin based composite (RBC). The cavities restored with Amelogen Plus displayed nonsignificantly higher microleakage than with Filtek Z250.

CONCLUSION

Although all of the restorative systems had microleakage, silorane technology showed less microleakage comparable to clinically successful methacrylate-based composite. This will improve the clinical performance and extend the composite durability.

Incremental techniques in direct composite restoration

Polymerization shrinkage is one of the dental clinician's main entanglements when placing resin-based composite restorations. None of the method can assure a perfectly sealed restoration for adhesive restorative materials; clinicians must abode problems of polymerization shrinkage and its possible ill effects. The objective of this article is to review different incremental techniques that can ruin the polymerization shrinkage stress of direct composite restoration.

Analyses of a cantilever-beam based instrument for evaluating the development of polymerization stresses

OBJECTIVE

This investigation was to generate (1) guidelines for designing a tensometer that satisfies the necessary accuracy and sensitivity requirements for measuring polymerization stress (PS), and (2) a formula for calculating PS. Polymerization stress remains one of the most critical properties of polymeric dental materials, yet methods that can accurately quantify PS have been limited in part due to the complexity of polymerization, and in part due to the instrumentation itself.

METHOD

In this study, we performed analytical and finite element analyses on a cantilever-beam based tensometer that is used to evaluate shrinkage stresses during the polymerization of dental restorative composites.

RESULTS

The PS generated by a commercial dental composite determined using our new tensometer agrees with the predicted trend when the beam length and/or specimen height is varied.

SIGNIFICANCE

This work demonstrates the importance of beam dimension and component relative rigidity to the accuracy of PS evaluation. An analytical solution is also derived for the vertical beam deflection, which can be used for any combination of bending and shearing to properly calculate the PS. In addition, an easy-to-conduct calibration procedure is provided that is desirable for periodic tensometer recalibration.

Comparative evaluation of microleakage around Class V cavities restored with alkasite restorative material with and without bonding agent and flowable composite resin: An in vitro study

Background

Marginal adaptability of restorative material is one of the prime factors for success of a restoration.

Aim

To evaluate microleakage at enamel restoration and dentin restoration interface of Class V cavities restored with new alkasite restorative material Cention-N, with and without using bonding agent and flowable composite resin.

Materials and Methods

Thirty Class V tooth preparations were divided into three groups (n = 10): Group-I restored with Cention-N (Ivoclar Vivadent) without adhesive, Group-II was restored with Cention-N after application of eighth-generation bonding agent (3M ESPE, Single Bond Universal Adhesive), and Group-III was restored with flowable composite resin (Tetric-N-Flow, Ivoclar Vivadent). All samples were subjected to 200 thermocycles between temperature baths at 5°C and 55°C. All samples were cut longitudinally through the center of the restorations with the help of isomet diamond saw. The sections were then observed under binocular stereomicroscope at 20×. Two evaluators scored the depth of dye penetration independently at enamel and dentin margins.

Statistical Analysis

Kruskal-Wallis nonparametric analysis followed by Dunn's multiple comparison tests were done to evaluate differences among the experimental groups. Mann-Whitney test was used to compare the difference between occlusal and gingival scores within each restoration.

Results

Microleakage seen in decreasing order: Cention-N without adhesive >Flowable composite >Cention-N with adhesive.

Conclusion

Microleakage at enamel restoration interface was less than microleakage at dentin restoration interface of each group, but the difference was not statistically significant. Least microleakage was seen with Cention-N with adhesive followed by flowable composite. More microleakage was seen with Cention-N without adhesive.

Comparative evaluation of microleakage in class II cavities restored with Ceram X and Filtek P-90: An in vitro study

Context:

Polymerization shrinkage in composite resins is responsible for microleakage. Methacrylate-based composite resins have linear reactive groups resulting in high polymerization shrinkage. A recently introduced composite resin Filtek P90 is based on siloxanes and oxiranes which polymerize by cationic “ring opening” polymerization resulting in reduced polymerization shrinkage.

Objectives:

Aim of this study was to compare microleakage in class II cavities restored with a nanoceramic restorative (Ceram X) and a silorane composite (Filtek P90).

Materials and Methods:

Standardized class II box type cavities were prepared on mesial (Groups Ia and IIa) and distal (Groups Ib and IIb) surfaces of twenty extracted permanent molar teeth with gingival floor ending 1 mm coronal and apical to the cementoenamel junction, respectively. The teeth in Group Ia and Ib were restored with Ceram X and Group IIa and IIb with Filtek P90. The specimens were thermocycled and microleakage evaluated.

Statistical Analysis Used:

The data were statistically analyzed using Wilcoxon Signed-Rank test at the 0.05 level of significance.

Results:

Mean microleakage score of group la and lb was 1 ± 2.260 and 2.8 ± 1.229, respectively. And that of group Ila and llb was 0.2 ± .869 and 0.3 ± .588, respectively. When groups I and II were compared, results were statistically significant (P<0.05).

Conclusion:

It was concluded that silorane-based composite may be a better substitute for methacrylate-based composites.

Physical Properties of an Ag-Doped Bioactive Flowable Composite Resin

The aim of this work was to study the physical and antibacterial properties of a flowable resin composite incorporating a sol-gel derived silver doped bioactive glass (Ag-BGCOMP). The depth of the cure was calculated by measuring the surface micro-hardness for the top and bottom surfaces. The volumetric polymerization shrinkage was measured by recording the linear shrinkage as change in length, while the biaxial flexural strength was studied measuring the load at failure. The antibacterial properties of the samples were tested against Streptococcus mutans (S. mutans) and Lactobacillus casei (L. casei). The measured values were slightly decreased for all tested physical properties compared to those of control group (flowable resin composite without Ag-BG), however enhanced bacteria inhibition was observed for Ag-BGCOMP. Ag-BGCOMP could find an application in low stress-bearing areas as well as in small cavity preparations to decrease secondary caries. This work provides a good foundation for future studies on evaluating the effects of Ag-BG addition into packable composites for applications in larger cavity preparations where enhanced mechanical properties are needed.

Overviews on the Progress of Flowable Dental Polymeric Composites: Their Composition, Polymerization Process, Flowability and Radiopacity Aspects

A review article has been conducted including the main research results and comments referring to flowable dental polymeric materials. To begin with, the synthesis and composition of this category of composites is discussed, revealing the major components of the commercial products in terms of chemistry and proportion. Later, the polymerization characteristics are unfolded regarding the reaction time and rate, volumetric shrinkage and depth of cure for both photocurable and self-curable composites. To continue, some perspectives of the pre-treatment or accompanying processes that a clinician may follow to enhance the materials' performance are described. Fluidity is certainly associated with the progress of polymerization and the in-depth conversion of monomers to a polymeric network. Last, the aspects of radiopacity and translucency are commented on, showing that all flowable polymeric composites satisfy the radiography rule, while the masking ability depends on the fillers' properties and specimen thickness. The reviewing article is addressed to all field scientists and practitioners dealing with flowable dental composites studies or applications.

Comparative evaluation of residual monomer content and polymerization shrinkage of a packable composite and an ormocer

Aim:

The aim of this study is to evaluate the residual monomer content and polymerization shrinkage of a packable composite (Surefil) and an ormocer (Admira).

Materials and Methods:

The study was conducted in two parts. In Part I, 10 samples of each material were prepared in a standardized split brass mould, using incremental curing technique. The residual monomer content was measured by observing change in weight before and after Soxhlet Extraction procedure. In part II, the volumetric polymerization shrinkage was calculated by measuring the difference in specific gravities of 10 uncured and 10 cured samples of each material using a modified version of ASTM D-792 method. The data obtained was put to statistical analysis using student's ‘t’ test.

Results:

Part I - The percentage change in weight for Surefil was 0.525% while that for Admira was 0.374%, which was found to be statistically significant. Part II - The volumetric percentage shrinkage for Surefil ranged between 1.04-3.42% and that for Admira between 1.01-2.31%, which was not found to be significant statistically.

Conclusion:

Admira may be considered more biocompatible than Surefil due to the lower residual monomer content in the former; however, both are comparable with regards to their polymerization shrinkage.

Polymerization Shrinkage Evaluation of Restorative Resin-Based Composites Using Fiber Bragg Grating Sensors

The purpose of this study was to compare the linear polymerization shrinkage of different restorative resin-based composites (RBCs) using fiber Bragg grating (FBG) sensors. Five RBCs were evaluated: Zirconfill^® (ZFL); Aura Bulk-Fill (ABF); Tetric^® N-Ceram Bulk-Fill (TBF); Filtek^TM Bulk-Fill (FBF); and Admira Fusion-Ormocer^® (ADF). Ten samples per resin were produced in standardized custom-made half-gutter silicone molds. Two optical FBG sensors were used to assess temperature and polymerization shrinkage. Light curing was performed for 40 s and polymerization shrinkage was evaluated at 5, 10, 40, 60, 150, and 300 s. Statistical analysis was accomplished for normal distribution (Shapiro-Wilk, p > 0.05). Two-way repeated measures ANOVA with Greenhouse-Geisser correction followed by Bonferroni′s post-hoc test was used to analyze the linear shrinkage data (p < 0.05). ZFL showed the highest linear shrinkage and ADF the lowest. Shrinkage increased for all RBCs until 300 s, where significant differences were found between ADF and all other resins (p < 0.05). Among bulk-fill RBCs, TBF showed the lowest shrinkage value, but not statistically different from FBF. The ADF presented lower linear shrinkage than all other RBCs, and restorative bulk-fill composites exhibited an intermediate behavior.

Contemporary curing profiles: Study of effectiveness of cure and polymerization shrinkage of composite resins: An in vitro study

AIMS

This study was undertaken to determine the effect of step-curing, ramp curing, single intensity on the effectiveness of cure and polymerization shrinkage of composite resin. The influence of filler loading on the effectiveness of cure and polymerization shrinkage of composite resin was investigated.

MATERIALS AND METHODS

In this study, a total of 80 specimens divided into four groups were used. Group I - specimens cured with the step-cure mode. Group II - specimens cured with single high intensity. Group III - specimens cured with the ramp-cure mode. Group IV - specimens cured with single low intensity. Each group had two subgroups based on the composite resins used for making the specimen. The effectiveness of cure was determined from surface hardness values obtained from Rockwell hardness testing. A mathematical volumetric method was used to assess the volumetric shrinkage.

RESULTS

Group III showed the best effectiveness of cure followed by group I and II. Group IV showed the least. Polymerization shrinkage was highest with group III and group II, were as was lowest for group I and IV. Charisma showed better effectiveness of cure and low polymerization shrinkage compared to Durafill VS.

CONCLUSION

This study emphasizes on the fact that, the soft-start polymerization modes (step curing and ramp curing) should be preferentially used over the conventional single (high or low light) intensities to cure composite resins, as its use results in optimal properties.

Degree of vinyl conversion, polymerization shrinkage and stress development in experimental endodontic composite

This study explores degree of vinyl conversion (DVC), polymerization shrinkage (PS) and shrinkage stress (PSS) of the experimental amorphous calcium phosphate (ACP) composites intended for use as an endodontic sealer. Light-cure (LC), chemical cure (CC) or dual-cure (DC; combined light and chemical cure) resins comprised urethane dimethacrylate (UDMA), 2-hydroxyethyl methacrylate (HEMA), methacryloyloxyethyl phthalate (MEP) and a high molecular mass oligomeric co-monomer, poly(ethyleneglycol)-extended UDMA (PEG-U) (designated UPHM resin). To fabricate composites, a mass fraction of 60 % UPHM resin was blended with a mass fraction of 40 % as-made (am-ACP) or ground ACP (g-ACP). DVC values of copolymer (unfilled UPHM resin) and composite specimens were determined by infrared spectroscopy. Glass-filled composites were used as controls. PS and PSS of composites were determined by dilatometry and tensometry, respectively. LC copolymers attained extraordinary high DVC values at 24 h post-cure (95.7 %), compared to CC (52 %) and DC (79.3 %) copolymer specimens. While the DVC values of LC and DC am-ACP composites were reduced between 5 and 10 %, DVC values of DC g-ACP composites increased almost 8 % compared to the corresponding copolymers. High DVC attained in LC composites was, expectedly, accompanied with high PS values (on average 7 vol%). However, PSS developed in LC and especially DC composites did not exceed PSS values seen in other UDMA-based composites. Based on this initial evaluation, it is concluded that, DC, g-ACP filled UPHM composite shows promise as an endodontic sealer. However, further physicochemical evaluations, including water sorption, mechanical stability and ion release as well as a leachability studies need to be performed before this experimental material is tested for cellular responses and, eventually recommended for clinical utility.

Relationships between Flexural and Bonding Properties, Marginal Adaptation, and Polymerization Shrinkage in Flowable Composite Restorations for Dental Application

To evaluate the flexural and bonding properties, marginal adaptation, and polymerization shrinkage in flowable composite restorations and their relationships, four new generation flowable composites, one conventional, and one bulk-fill flowable composite were used in this study. Flexural properties of the composites and shear bond strength to enamel and dentin for flowable restorations were measured immediately and 24 h after polymerization. Marginal adaptation, polymerization shrinkage, and stress were also investigated immediately after polymerization. The flexural properties, and bond strength of the flowable composites to enamel and dentin were much lower immediately after polymerization than at 24 h, regardless of the type of the composite. Polymerization shrinkage and stress varied depending on the material, and bulk-fill flowable composite showed much lower values than the others. The marginal adaptation and polymerization shrinkage of the composites appeared to have a much stronger correlation with a shear bond strength to dentin than to enamel. The weak mechanical properties and bond strengths of flowable composites in the early stage after polymerization must be taken into account when using them in the clinic. In addition, clinicians should be aware that polymerization shrinkage of flowable composites can still lead to the formation of gaps and failure of adaptation to the cavity regardless of the type of composite.

Effect of Cast Modification on Denture Base Adaptation Following Maxillary Complete Denture Processing

PURPOSE

To investigate the effect of cast modifications on denture base adaptation in coronal and sagittal projections following maxillary complete denture processing.

MATERIALS AND METHODS

A total of 60 edentulous maxillary casts (n = 10) were distributed among six groups. Group 1 was the control group with no modification, groups 2 through 6 included a butterfly postdam preparation, groups 3 and 4 also included a 10-mm wide/4-mm deep box with addition of four round holes in group 4, and groups 5 and 6 also included a 20-mm wide/4-mm deep box with addition of four round holes in group 6. The boxes were prepared at the mid-heel area of the casts. Two layers of baseplate wax (1 mm each) were used to standardize denture base thickness across the groups. A standard technique was used to replicate the denture tooth set-up, and standardized processing was done for all the groups. Following deflasking, casts with the dentures were sectioned in the coronal and sagittal directions. Microscopic pictures were taken at preselected points. Data were organized in tables, and statistical analyses were performed using repeated measure ANOVA, Tukey post hoc tests, and post hoc comparison tests set at 5% level of significance.

RESULTS

Maximum gaps were measured at the mid-palatal area followed by nearby areas and the areas near ridge crests in both coronal and sagittal projections. The analyses revealed significant differences between the groups in coronal projection (1/2, 3/4, 5/6) and sagittal projection (1, 2, 3/4, 5/6) without significant differences within the pairs. The groups were ranked from the highest group 1 to the lowest group 6 relative to the gap means. Post hoc comparisons showed that points 1C and 2A had the highest gap means across the study groups.

CONCLUSIONS

Within the limitations of this study, it can be extrapolated that the denture base adaptation can be effectively increased with the box preparation at the mid-heel aspect of the casts. Significant reduction of gaps was seen when the box size increased from 10 to 20 mm in coronal and sagittal projections; however, the addition of four holes had no significant effect on gap size alterations.

Light diffusion through composite restorations added with spherical glass mega fillers

PURPOSE

Evaluate how the spherical glass mega fillers (SGMFs) can positively interfere with light diffusion when incorporated in a composite restoration.

MATERIALS AND METHODS

30 samples (Ss) were performed, applying 2 composite layers of 3 mm each: 6 were made with composite only; 6 with a layer of SGMFs of O1.5mm within the first layer of composite; 6 with 2 overlapping layers of SGMFs of O1.5mm; 6 with a layer of SGMFs of O2mm; 6 with 2 overlapping layers of SGMFs of O2mm. The curing time was set at 40s for the first layer, and 120s for the second layer, transilluminated through the first layer. Digital pictures were taken, in standardized settings, during the transillumination, and the light intensity was measured with a digital image analysis software.

RESULTS

From a lateral view the Ss with a single layer of SGMFs of O1.5mm and O2mm, the relative increments of light intensity, were of 24.37% and 33.33% respectively. Concerning the Ss made with 2 layers of SGMFs, the relative increments were of 67.99% and 66.4% respectively. In front view has emerged a relative increase rate of light intensity of 53.66% and 79.58%, in the Ss with a single layer of SGMFs of O1.5mm and of O2mm respectively. Furthermore, in the Ss with two layers of SGMFs of O1.5mm and O2mm the relative increments were of 267.53 and 319.63% respectively.

CONCLUSION

The SGMFs are reliable in facilitating light diffusion within the light-curing composite resins.

Effect of volumetric shrinkage of restorative materials on tooth structure: A finite element analysis

Post-treatment coronal hermetic seal of the root canal opening prevents the food or saliva which assist to achieve successful endodontic treatment. Gutta-percha is filled in the inner canal, that is, from cervical third to apical third. Gutta-percha does not provide the hermetic seal because it does not bound with dentine walls. Various new restorative materials have been developed in the last 6-7 decade but drawback related to the polymerization shrinkage of the composite resin remains a clinical problem. In general, dental composites having volumetric shrinkage of the material depends on its formulation and curing conditions. In this article, the effect of this polymerization shrinkage on the tooth structure has been studied.

Polymerization shrinkage and spherical glass mega fillers: effects on cuspal deflection

PURPOSE

The Authors analyzed the effect of spherical glass mega fillers (SGMF) on reducing contraction stress in dental composite resins, by means of a cavity model simulating the cuspal deflection which occurs on filled tooth cavity walls in clinical condition.

MATERIALS AND METHODS

20 stylized MOD cavities (C-factor = 0.83) were performed in acrylic resin. The inner surface of each cavity was sand blasted and adhesively treated in order to ensure a valid bond with the composite resin. Three different diameter of SGMF were used (i.e. 1, 1,5, 2 mm). The samples were divided in 4 groups of 5 each: Group 1 samples filled with the composite only; Group 2 samples filled with composite added with SGMFs, Ø1mm (16 spheres for each sample); Group 3 samples filled with composite added with SGMFs, Ø1,5 mm (5 spheres for each sample); Group 4 samples filled with composite added with SGMFs, Ø2 mm (2 spheres for each sample). Digital pictures were taken, in standardized settings, before and immediately after the polymerization of the composite material, placed into the cavities. With a digital image analysis software the distances from the coronal reference points of the cavity walls were measured. Then the difference between the first and second measurement was calculated. The data were analyzed by means of the ANOVA test.

RESULTS

A significative reduction on cavity walls deflection, when the composite resin is used in addiction with the SGMFs was observed. The SGMFs of smallest diameter (1mm) showed the better outcome.

CONCLUSION

The SGMFs are reliable in reducing contraction stress in dental composite resins.

Copolymerization of Ring-Opening Oxaspiro Comonomer with Denture Base Acrylic Resin by Free-Radical/Cationic Hybrid Polymerization

BACKGROUND

Polymerization shrinkage is an innate characteristic of thermo-polymerized denture base acrylic resin. Volumetric shrinkage is still a problem, although myriad material modifications. Ring-opening oxaspiro monomers have promising volumetric expansions of about 7%. These monomers have diminished the shrinkage in dental filling resins through copolymerization (CP). However, their CP with denture base resins is not reported yet.

PURPOSE

The aim is to confirm the CP of an oxaspiro monomer with methyl methacrylate (MMA) by radical-cationic hybrid polymerization and to assess the degree of conversion (DC) of the formed copolymer.

MATERIALS AND METHODS

The oxaspiro monomer was synthesized by a transesterification reaction. The study groups were based on the composition and thermo-polymerization method. The control and E1 groups were thermo-polymerized in water-bath, whereas the E2 group in a laboratory autoclave. Both E1 and E2 groups contained the oxaspiro monomer and cationic initiator. E2 group had an additional radical initiator. The CP and DC were confirmed and assessed by infrared spectroscopy.

RESULTS

Accentuation of carbonyl peak, the disappearance of the spiro-carbon peak, and the appearance of ether linkages in experimental groups confirmed the ring-opening. E2 group had the highest DC.

CONCLUSION

The oxaspiro monomer successfully copolymerized with MMA and had good DC.

Synthesis and Characterization of a Ring-Opening Oxaspiro Comonomer by a Novel Catalytic Method for Denture Base Resins

Background:

3,9-Dimethylene-1,5,7,11-tetraoxaspiro[5,5]undecane (DMTOSU) is a double ring-opening monomer that exhibits expansion upon polymerization and may be used as a denture base resin's comonomer to offset or minimize polymerization shrinkage. It's synthesis by transesterification reaction (TE) catalyzed by distannoxane is not reported in the literature. The synthesis became the prime concern because this monomer is hardly available commercially.

Purpose:

The purpose is to confirm the DMTOSU synthesis and compare the synthesized monomers obtained by two different catalytic processes through Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopies.

Materials and Methods:

Scheme I synthesis was by TE catalyzed by dichlorotetrabutyl distannoxane (DCBS) yielding M1 monomer. Scheme II synthesis was catalyzed by dibutyltin oxide-carbon disulfide (DBTO-CS₂) yielding M2 monomer.

Results:

The appearance of a characteristic peak at 1212 cm⁻¹ in FTIR spectrum, a doublet at δ 4.95 in ¹H-NMR spectrum and a peak at δ 117.12 in ¹³C-NMR spectrum confirmed the synthesis of DMTOSU-M1catalyzed by DCBS, which is not significantly different from DMTOSU-M2 catalyzed by DBTO-CS₂.

Conclusion:

The catalytic action of DCBS is a successful alternative to the DBTO-CS₂ catalysis in DMTOSU synthesis.

A comparative evaluation of effect of modern-curing lights and curing modes on conventional and novel-resin monomers

Aim:

The aim of this study is to compare and to evaluate effect of curing light and curing modes on the nanohybrid composite resins with conventional Bis-GMA and novel tricyclodecane (TCD) monomers.

Methodology:

Two nanohybrid composites, IPS empress direct and charisma diamond were used in this study. Light-emitting diode (LED)-curing unit and quartz-tungsten-halogen (QTH)-curing unit which were operated into two different modes: continuous and soft start. Based on the composite resin, curing lights, and mode of curing used, the samples were divided into 8 groups. After polymerization, the samples were stored for 48 h in complete darkness at 37°C and 100% humidity. The Vickers hardness (VK) of the surface was determined with Vickers indenter by the application of 200 g for 15 s. Three VK readings were recorded for each sample surface both on top and bottom surfaces. For all the specimens, the three hardness values for each surface were averaged and reported as a single value. The mean VK and hardness ratio were calculated. The depth of cure was assessed based on the hardness ratio.

Results:

Comparison of mean hardness values and hardness ratios was done using ANOVA with post hoc Tukey's test.

Conclusion:

Both QTH- and LED-curing units had shown the adequate depth of cure. Soft-start-curing mode in both QTH- and LED-curing lights had effectively increased microhardness than the continuous mode of curing. TCD monomer had shown higher hardness values compared with conventional Bis-GMA-containing resin.