Effects of dilution and pretreatment on nutrient removal and biomass production of Chlorella vulgaris in kitchen wastewater

This research investigated the effect of kitchen wastewater (KWW) concentrations and pretreatment methods on Chlorella vulgaris biomass production, lipid content and nutrient removal. This study was divided into two separate experiments. The first experiment determined the appropriate dilution rate of KWW for the growth of microalgae, sterilized KWW was varied between 25%, 50%, 75%, and 100%(v/v). The result indicated that 50%(v/v) showed the highest nutrient removal by 90.23%, 85.87%, and 80.64% of sCOD, TKN, and TP, respectively. The highest biomass and lipid content were obtained with 50%(v/v) (1.447 g/L, 37.9%). The second experiment was to find an effective physical pretreatment method, which separated the biotic contaminant, non-sterilized KWW was diluted 50%(v/v) and filtered with different mesh size filters (150 μm, 50 μm, and 30 μm) compared with sterilized KWW as a control sample. The result indicated that pretreatment with 50 μm filtration was found highest nutrient removal by 90.51%, 84.74%, and 77.50% of sCOD, TKN, and TP, respectively. The highest biomass and lipid content were obtained with 50 μm filtration (1.496 g/L, 39.4%). Our results support the hypothesis that the optimal dilution and proper filtration of KWW helps create more favorable environment for microalgal growth.

Influence of Pretreatment Methods on Compressive Performance Improvement and Failure Mechanism Analysis of Recycled Aggregate Concrete

The utilization of recycled aggregate can avert the squandering of resources and the destruction of the environment. Nevertheless, there exists a slew of old cement mortar and microcracks on the surface of recycled aggregate, which give rise to the poor performance of aggregates in concrete. In this study, for the sake of ameliorating this property of recycled aggregates, the surface of the recycled aggregates is covered with a layer of cement mortar to compensate for the microcracks on the surface and reinforce the bond between old cement mortar and aggregates. In order to demonstrate the influence of recycled aggregate by different cement mortar pretreatment methods, this study prepared natural aggregate concrete (NAC) and concretes with recycled aggregate after the wetting pretreatment (RAC-W) and cement mortar pretreatment (RAC-C), and conducted uniaxial compressive strength tests on different types of concrete at different curing ages. The test results indicated that the compressive strength of RAC-C at a 7 d curing age was higher than that of RAC-W and NAC, and the compressive strength of RAC-C at a 28 d curing age was higher than RAC-W but lower than NAC. The compressive strength of NAC and RAC-W at a 7 d curing age was about 70% of that at a 28 d curing age, and the compressive strength of RAC-C at a 7 d curing age was about 85-90% of that at a 28 d curing age. The compressive strength of RAC-C increased dramatically at the early stage, while the post-strength of the NAC and RAC-W groups increased rapidly. The fracture surface of RAC-W mainly occurred in the transition zone between the recycled aggregates and old cement mortar under the pressure of the uniaxial compressive load. However, the main failure of RAC-C was the crushing destruction of cement mortar. With changes in the amount of cement added beforehand, the proportion of aggregate damage and A-P interface damage of RAC-C also changed accordingly. Therefore, the recycled aggregate pretreated with cement mortar can significantly improve the compressive strength of recycled aggregate concrete. The optimal amount of pre-added cement was 25%, which is recommended for practical engineering.

Improved Denitrification Performance of Polybutylene Succinate/Corncob Composite Carbon Source by Proper Pretreatment: Performance, Functional Genes and Microbial Community Structure

Blending biodegradable polymers with plant materials is an effective method to improve the biodegradability of solid carbon sources and save denitrification costs, but the recalcitrant lignin in plant materials hinders the microbial decomposition of available carbon sources. In the present study, corncob pretreated by different methods was used to prepare polybutylene succinate/corncob (PBS/corncob) composites for biological denitrification. The PBS/corncob composite with alkaline pretreatment achieved the optimal NO₃^--N removal rate (0.13 kg NO₃^--N m^-3 day^-1) with less adverse effects. The pretreatment degree, temperature, and their interaction distinctly impacted the nitrogen removal performance and dissolved organic carbon (DOC) release, while the N₂O emission was mainly affected by the temperature and the interaction of temperature and pretreatment degree. Microbial community analysis showed that the bacterial community was responsible for both denitrification and lignocellulose degradation, while the fungal community was primarily in charge of lignocellulose degradation. The outcomes of this study provide an effective strategy for improving the denitrification performance of composite carbon sources.

Rapid, Simultaneous, and Automatic Determination of Lead and Cadmium in Cereals with a New High Performance Composite Hollow Cathode Lamp Coupled to Graphite Furnace Atomic Absorption Spectrometry

A simple, rapid, sensitive, accurate, and automatic graphite furnace atomic absorption spectrometry (GFAAS) method for detecting Cd and Pb in cereals is presented. This method enables the simultaneous determination of Cd and Pb in cereals with a pre-treatment method of diluted acid extraction and a high-performance lead-cadmium composite hollow-cathode lamp (LCC-HCL), and it realizes automatic determination from sample weighing to result output through an automatic diluted acid extraction system. Under the optimization, Pb and Cd in cereals were simultaneously and automatically detected in up to 240 measurements in 8 h. The LOD and LOQ of this method were 0.012 and 0.040 mg·kg^-1 for Pb, and 0.0014 and 0.0047 mg·kg^-1 for Cd, respectively. The results of the four certified reference materials were satisfied; there was no significant difference compared with the ICP-MS method according to a t-test, and the RSDs were less than 5% for Cd and Pb. The recoveries of naturally contaminated samples compared with the ICP-MS method were favorable, with 80-110% in eight laboratories. The developed method is rapid, low-cost, and highly automated and may be a good choice for grain quality discrimination and rapid analysis of Cd and Pb in different institutions.

Monolith or Powder: Improper Sample Pretreatment May Mislead the Understanding of Industrial V2O5-WO3/TiO2 Catalysts Operated in Stationary Resources

Although various characterizations are widely applied to commercial V₂O₅-WO₃/TiO₂ catalysts, the influence of the catalyst physical structure, i.e., monolith or powder, on the characterization results has not been investigated. Several important catalytic behaviors and phenomena were observed in this study using V₂O₅-WO₃/TiO₂ monolithic catalysts employed for over 5000 h in various stationary flue gases, and many of the results were only observable on monolithic catalysts, such as depth-dependent distribution of external elements, penetration of As₂O₃, and the formation of Tl₂O-TiO₂ p-n junctions. If the monolith is ground into powder states, it will alter or destroy the catalyst surface and remove important clues closely related to catalytic performance under working conditions. The redox and acidity properties of V₂O₅-WO₃/TiO₂ obtained from powder samples may be significantly different from their true state under working conditions, resulting in a misperception of catalyst performance. Therefore, a cautious pretreatment should be taken into careful consideration when analyzing commercial honeycomb V₂O₅-WO₃/TiO₂ catalysts.

Development of a colloidal gold immunochromatographic strip for the rapid detection of pefloxacin in grass carp with a novel pretreatment method

A rapid colloidal gold immunochromatography assay (GICA) for the detection of pefloxacin (PEF) was established and optimized. The anti-PEF monoclonal antibody (mAb) was used to target PEF as a colloidal gold-mAb conjugate. The mAb belonged to the IgG2b subtype, lambda light chain, the affinity constant (Ka) was 5.21 × 10⁹ L·mol^-1, and its half maximal inhibitory concentration (IC₅₀) was 0.23 ng·mL^-1. No obvious cross-reactivity (CR) was observed with other common fluoroquinolone antibiotics, including ciprofloxacin (CIP), norfloxacin (NOR), lomefloxacin (LOM) and ofloxacin (OFL). The visual limit of detection (vLOD) of the optimized GICA was 2 ng·g^-1 under the conventional pretreatment method, and the assay was completed in 15 min. Liquid chromatography tandem-mass spectrometry (LC-MS/MS) was employed to confirm the performance of the strip. In addition, a novel pretreatment was established and compared with conventional pretreatment. Without the removal of organic solvents, the novel pretreatment method reduced the sample pretreatment time (more than 10 min). The vLOD of the optimized GICA was also 2 ng·g^-1 when applying the novel pretreatment method. In conclusion, the proposed PEF-GICA could detect samples containing PEF rapidly and accurately, and the novel pretreatment method saved the time of sample pretreatment and improved the efficiency of detection.

Preliminary investigation of microplastics in the production process of sea salt sourced from the Bohai Sea, China, using an optimised and consistent approach

In this study, we present a preliminary investigation of the characteristic changes in microplastic during the production process of sea salt in China. Five representative samples, including seawater, saturated brine, crude salt, coarse salt, and refined salt were successively collected from the production process of sea salt sourced from the Bohai Sea in China. The pretreatment method of microplastics was optimised and evaluated by the recovery rates of particle references. Microplastic characteristics in the five samples were investigated using consistent pretreatment, microscopic, and spectroscopic analyses. Results indicated that microplastics were present in every stage of sea salt production. During the "journey" of microplastics in salt production from seawater-to-seawater evaporation, to salt crystallisation, and external force processing, the abundance of microplastics with size ranging from 18 μm to 4936 μm increased substantially from 23 ± 8 to 413 ± 61 particles kg^-1, while the proportion of larger microplastics (≥1000 μm) decreased from 33% to 9%. The results illustrate the effect of the production process on microplastic contamination of sea salt.