26
|
Ge X, Rao G, Kostov Y, Kanjananimmanont S, Viscardi RM, Woo H, Tolosa L. Detection of trace glucose on the surface of a semipermeable membrane using a fluorescently labeled glucose-binding protein: a promising approach to noninvasive glucose monitoring. J Diabetes Sci Technol 2013; 7:4-12. [PMID: 23439155 PMCID: PMC3692211 DOI: 10.1177/193229681300700102] [Citation(s) in RCA: 10] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 11/15/2022]
Abstract
BACKGROUND Our motivation for this study was to develop a noninvasive glucose sensor for low birth weight neonates. We hypothesized that the underdeveloped skin of neonates will allow for the diffusion of glucose to the surface where it can be sampled noninvasively. On further study, we found that measurable amounts of glucose can also be collected on the skin of adults. METHOD Cellulose acetate dialysis membrane was used as surrogate for preterm neonatal skin. Glucose on the surface was collected by saline-moistened swabs and analyzed with glucose-binding protein (GBP). The saline-moistened swab was also tested in the neonatal intensive care unit. Saline was directly applied on adult skin and collected for analysis with two methods: GBP and high-performance anion-exchange chromatography (HPAEC). RESULTS The amount of glucose on the membrane surface was found (1) to accumulate with time but gradually level off, (2) to be proportional to the swab dwell time, and (3) the concentration of the glucose solution on the opposite side of the membrane. The swab, however, failed to absorb glucose on neonatal skin. On direct application of saline onto adult skin, we were able to measure by HPAEC and GBP the amount of glucose collected on the surface. Blood glucose appears to track transdermal glucose levels. CONCLUSIONS We were able to measure trace amounts of glucose on the skin surface that appear to follow blood glucose levels. The present results show modest correlation with blood glucose. Nonetheless, this method may present a noninvasive alternative to tracking glucose trends.
Collapse
|
27
|
Ge X, Kostov Y, Tolosa L, Rao G. Study on low-cost calibration-free pH sensing with disposable optical sensors. Anal Chim Acta 2012; 734:79-87. [PMID: 22704475 DOI: 10.1016/j.aca.2012.05.021] [Citation(s) in RCA: 14] [Impact Index Per Article: 1.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/28/2011] [Revised: 05/14/2012] [Accepted: 05/16/2012] [Indexed: 11/19/2022]
Abstract
As labor costs become more expensive, less labor-intensive disposable devices have become more ubiquitous. Similarly, the disposable optical pH sensor developed in our lab could provide a convenient yet cost-effective way for pH sensing in processes that require stringent pH control. This optical pH sensor is prepared in uniform individual lots of 100-200 sensors per lot. Calibration is accomplished on a few randomly selected sensors out of each lot. We show that all others in the same lot can then be used directly without requiring individual calibration. In this paper, a calibration model is derived to include all the factors that affect the signal of the disposable sensor. Experimental results show that the derived calibration model fits the experimental data. The readings of 28 randomly selected disposable sensors with 4 sensors from each of the 7 lots show an error less than 0.1 pH units in the useful sensing range of the sensor. The calibration model indicates that if further improvement on precision is desired, more uniform porous material and more advanced coating techniques will be required. When it comes to the effects of the varying coasters, house-made low-cost fluorometers, the variability in the brightness ratio of the blue-to-violet LEDs is the primary reason for the lack of precision. Other factors like LED light intensity distribution, optical properties of the filters and electronics also contribute to the coaster-to-coaster difference, but to a lesser extent. Two different methods for correcting the instrument variations were introduced. After correction, the collective reading errors for all the tested instruments were reduced to less than 0.2 pH units within the sensor's useful sensing range. Based on this result, our lab is currently implementing further improvements in modifying the coasters to equalize the ratios of blue-to-violet LED brightness.
Collapse
|
28
|
Lam H, Kostov Y, Tolosa L, Falk S, Rao G. High Resolution Non-contact Fluorescence Based Temperature Sensor for Neonatal Care. MEASUREMENT SCIENCE & TECHNOLOGY 2012; 23:035104. [PMID: 22923882 PMCID: PMC3423978 DOI: 10.1088/0957-0233/23/3/035104] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/01/2023]
Abstract
To date, thermistors are used to continuously monitor the body temperature of newborn babies in the neonatal intensive care unit. The thermistor probe is attached to the body with a strong adhesive tape to ensure that the probe stays in place. However, these strong adhesives are shown to increase microbial growth and cause serious skin injuries via epidermal stripping. The latter compromises the skin's ability to serve as a protective barrier leading to increase in water loss and further microbial infections. In this article a new approach is introduced that eliminates the need for an adhesive. Instead, two kinds of fluorophores are entrapped in a skin friendly chitosan gel that can be easily wiped on and off of the skin, and has antimicrobial properties as well. A CCD camera is used to detect the temperature dependent fluorescence of the fluorophore, tris(1,10-phenthroline)ruthenium(II) while 8-aminopyrene-1,3,6-trisulfonic acid serves as the reference. This temperature sensor was found to have a resolution of at least 0.13°C.
Collapse
|
29
|
Lam H, Rao G, Loureiro J, Tolosa L. Dual optical sensor for oxygen and temperature based on the combination of time domain and frequency domain techniques. Talanta 2010; 84:65-70. [PMID: 21315899 DOI: 10.1016/j.talanta.2010.12.016] [Citation(s) in RCA: 21] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/08/2010] [Revised: 12/03/2010] [Accepted: 12/07/2010] [Indexed: 10/18/2022]
Abstract
In measuring specific conditions in the real world, there are many situations where both the oxygen concentration and the temperature have to be determined simultaneously. Here we describe a dual optical sensor for oxygen and temperature that can be adapted for different applications. The measurement principle of this sensor is based on the luminescence decay times of the oxygen-sensitive ruthenium complex tris-4,7-diphenyl-1,10-phenanthroline ruthenium(III) [Rudpp] and the temperature-sensitive europium complex tris(dibenzoylmethane) mono(5-amino-1,10-phenanthroline)europium(III) [Eudatp]. The excitation and emission spectra of the two luminophores overlap significantly and cannot be discriminated in the conventional way using band pass filters or other optical components. However, by applying both the frequency and time domain techniques, we can separate the signals from the individual decay time of the complexes. The europium complex is entrapped in a poly(methyl methacrylate) (PMMA) layer and the ruthenium complex is physically adsorbed on silica gel and incorporated in a silicone layer. The two layers are attached to each other by a double sided silicone based tape. The europium sensing film was found to be temperature-sensitive between 10 and 70°C and the ruthenium oxygen-sensitive layer can reliably measure between 0 and 21% oxygen.
Collapse
|
30
|
Castell J, Tolosa L, Pinto S, Donato M, O’connor J, Gómez-Lechón M. Development of multiparametric cell-based protocol to assess and classify hepatotoxicity potential of drugs. Toxicol Lett 2010. [DOI: 10.1016/j.toxlet.2010.03.478] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/19/2022]
|
31
|
Lam H, Kostov Y, Rao G, Tolosa L. A luminescence lifetime assisted ratiometric fluorimeter for biological applications. THE REVIEW OF SCIENTIFIC INSTRUMENTS 2009; 80:124302. [PMID: 20059156 PMCID: PMC2803713 DOI: 10.1063/1.3264106] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/10/2009] [Accepted: 10/26/2009] [Indexed: 05/28/2023]
Abstract
In general, the most difficult task in developing devices for fluorescence ratiometric sensing is the isolation of signals from overlapping emission wavelengths. Wavelength discrimination can be achieved by using monochromators or bandpass filters, which often lead to decreased signal intensities. The result is a device that is both complex and expensive. Here we present an alternative system--a low-cost standalone optical fluorimeter based on luminescence lifetime assisted ratiometric sensing (LARS). This paper describes the principle of this technique and the overall design of the sensor device. The most significant innovation of LARS is the ability to discriminate between two overlapping luminescence signals based on differences in their luminescence decay rates. Thus, minimal filtering is required and the two signals can be isolated despite significant overlap of luminescence spectra. The result is a device that is both simple and inexpensive. The electronic circuit employs the lock-in amplification technique for the signal processing and the system is controlled by an onboard microcontroller. In addition, the system is designed to communicate with external devices via Bluetooth.
Collapse
|
32
|
Mir M, Asensio VJ, Tolosa L, Gou-Fabregas M, Soler RM, Lladó J, Olmos G. Tumor necrosis factor alpha and interferon gamma cooperatively induce oxidative stress and motoneuron death in rat spinal cord embryonic explants. Neuroscience 2009; 162:959-71. [PMID: 19477238 DOI: 10.1016/j.neuroscience.2009.05.049] [Citation(s) in RCA: 46] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/02/2009] [Revised: 05/15/2009] [Accepted: 05/21/2009] [Indexed: 12/13/2022]
Abstract
The accumulation of reactive microglia in the degenerating areas of amyotrophic lateral sclerosis (ALS) tissue is a key cellular event creating a chronic inflammatory environment that results in motoneuron death. We have developed a new culture system that consists in rat spinal cord embryonic explants in which motoneurons migrate outside the explant, growing as a monolayer in the presence of glial cells. The proinflammatory cytokines tumor necrosis factor alpha (TNF-alpha) and interferon gamma (IFN-gamma) have been proposed to be involved in ALS-linked microglial activation. In our explants, the combined exposure to these cytokines resulted in an increased expression of the pro-oxidative enzymes inducible nitric oxide synthase (iNOS), the catalytic subunit of the nicotinamide adenine dinucleotide phosphate (NADPH) oxidase, gp91(phox) and cyclooxygenase-2 (COX-2), as compared to each cytokine alone. This effect was related to their cooperation in the activation of the transcription factor nuclear factor kappa B (NF-kappaB). TNF-alpha and IFN-gamma also cooperated to promote protein oxidation and nitration, thus increasing the percentage of motoneurons immunoreactive for nitrotyrosine. Apoptotic motoneuron death, measured through annexin V-Cy3 and active caspase-3 immunoreactivities, was also found cooperatively induced by TNF-alpha and IFN-gamma. Interestingly, these cytokines did not affect the viability of purified spinal cord motoneurons in the absence of glial cells. It is proposed that the proinflammatory cytokines TNF-alpha and IFN-gamma have cooperative/complementary roles in inflammation-induced motoneuron death.
Collapse
|
33
|
Badugu R, Kostov Y, Rao G, Tolosa L. Development and application of an excitation ratiometric optical pH sensor for bioprocess monitoring. Biotechnol Prog 2009; 24:1393-401. [PMID: 19194954 DOI: 10.1002/btpr.66] [Citation(s) in RCA: 29] [Impact Index Per Article: 1.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022]
Abstract
The development of a fluorescent excitation ratiometric pH sensor (AHQ-PEG) using a novel allylhydroxyquinolinium (AHQ) derivative copolymerized with polyethylene glycol dimethacrylate (PEG) is described. The AHQ-PEG sensor film is shown to be suitable for real-time, noninvasive, continuous, online pH monitoring of bioprocesses. Optical ratiometric measurements are generally more reliable, robust, inexpensive, and insensitive to experimental errors such as fluctuations in the source intensity and fluorophore photobleaching. The sensor AHQ-PEG in deionized water was shown to exhibit two excitation maxima at 375 and 425 nm with a single emission peak at 520 nm. Excitation spectra of AHQ-PEG show a decrease in emission at the 360 nm excitation and an increase at the 420 nm excitation with increasing pH. Accordingly, the ratio of emission at 420:360 nm excitation showed a maximum change between pH 5 and 8 with an apparent pK(a) of 6.40. The low pK(a) value is suitable for monitoring the fermentation of most industrially important microorganisms. Additionally, the AHQ-PEG sensor was shown to have minimal sensitivity to ionic strength and temperature. Because AHQ is covalently attached to PEG, the film shows no probe leaching and is sterilizable by steam and alcohol. It shows rapid (approximately 2 min) and reversible response to pH over many cycles without any photobleaching. Subsequently, the AHQ-PEG sensor film was tested for its suitability in monitoring the pH of S. cereviseae (yeast) fermentation. The observed pH using AHQ-PEG film is in agreement with a conventional glass pH electrode. However, unlike the glass electrode, the present sensor is easily adaptable to noninvasive monitoring of sterilized, closed bioprocess environments without the awkward wire connections that electrodes require. In addition, the AHQ-PEG sensor is easily miniaturized to fit in microwell plates and microbioreactors for high-throughput cell culture applications.
Collapse
|
34
|
Tolosa L. On the design of low-cost fluorescent protein biosensors. ADVANCES IN BIOCHEMICAL ENGINEERING/BIOTECHNOLOGY 2009; 116:143-57. [PMID: 19347267 DOI: 10.1007/10_2008_39] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 04/04/2023]
Abstract
There is a large body of knowledge on proteins and their ligands that is available to the sensor researcher for the successful design of fluorescent biosensors. Chemically synthesized receptors rarely match the sensitivity and selectivity of proteins.Additionally, proteins are easily produced and manipulated through recombinant protein techniques. Although limitations exist in the prediction of signal response of proteins labeled with fluorescent probes, thoughtful experimentation can lead to useful, highly responsive fluorescent protein assays. Conversion of these assays into sensor devices may require additional manipulation of the fluorescence properties of the labeled proteins. We have shown that this can be achieved by a second fluorophore serving as a reference for ratiometric measurements. The choice of reference is contingent on the low-cost, miniaturized design of the device. Accordingly, the reference fluorophore is excitable with the same LED as the signal transducing probe and has a fluorescence decay lifetime that is orders of magnitude longer.Alternating illumination with intensity modulated light at two frequencies allows for ratiometric sensing without the need for bulky filter wheels while collecting the signals over a wide range of emission wavelengths. The result is a simple optoelectronics design that is cost-effective and small enough to be portable.In summary, the process of designing protein-based fluorescent biosensors for practical applications requires the systematic collaboration of a cross-disciplinary group of molecular biologists, chemists and engineers.
Collapse
|
35
|
Tolosa L, Mir M, Olmos G, Lladó J. Vascular endothelial growth factor protects motoneurons from serum deprivation–induced cell death through phosphatidylinositol 3-kinase-mediated p38 mitogen-activated protein kinase inhibition. Neuroscience 2009; 158:1348-55. [DOI: 10.1016/j.neuroscience.2008.10.060] [Citation(s) in RCA: 36] [Impact Index Per Article: 2.4] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/24/2008] [Revised: 10/17/2008] [Accepted: 10/31/2008] [Indexed: 11/30/2022]
|
36
|
Lam H, Kostov Y, Rao G, Tolosa L. Low-cost optical lifetime assisted ratiometric glutamine sensor based on glutamine binding protein. Anal Biochem 2008; 383:61-7. [PMID: 18786501 DOI: 10.1016/j.ab.2008.08.018] [Citation(s) in RCA: 12] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/18/2008] [Revised: 07/21/2008] [Accepted: 08/07/2008] [Indexed: 11/16/2022]
Abstract
Here we report a reagentless fluorescence sensing technique for glutamine in the submicromolar range based on the glutamine binding protein (QBP). The S179C mutant is labeled with the short-lived acrylodan (lifetime<5ns) and the long-lived tris(dibenzoylmethane) mono(5-amino-1,10-phenanthroline)europium(III) (lifetime > 300 micros) at the -SH and the N-terminal positions, respectively. In the presence of glutamine the fluorescence of acrylodan is quenched, while the fluorescence of europium complex remains constant. In this report we describe an innovative technique, the so called lifetime assisted ratiometric sensing to discriminate the two fluorescence signals using minimal optics and power requirements. This method exploits the large difference between the fluorescence lifetimes of the two fluorophores to isolate the individual fluorescence from each other by alternating the modulation frequency of the excitation light between 300 Hz and 10 kHz. The result is a ratiometric optical method that does not require expensive and highly attenuating band pass filters for each of the dyes, but only one long pass filter for both. Thus, the signal to noise ratio is enhanced, and at the same time, the optical setup is simplified. The end product is a simple sensing device suitable for low-cost applications such as point-of-care diagnostics or in-the-field analysis.
Collapse
|
37
|
Ge X, Rao G, Tolosa L. On the possibility of real-time monitoring of glucose in cell culture by microdialysis using a fluorescent glucose binding protein sensor. Biotechnol Prog 2008; 24:691-7. [PMID: 18422364 DOI: 10.1021/bp070411k] [Citation(s) in RCA: 15] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
Abstract
Although glucose sensors with millimolar sensitivity are still the norm, there is now a developing interest in glucose sensors with micromolar sensitivity for applications in minimally invasive sampling techniques such as fast microdialysis and extraction of interstitial fluid by iontophoresis and laser poration. In this regard, the glucose binding protein (GBP) with a binding constant for glucose in the micromolar range is of particular relevance. GBP is one of the soluble binding proteins found in the periplasmic space of Gram-negative bacteria. Because of its hinge-like tertiary structure, glucose binding induces a large conformational change, which can be used for glucose sensing by attaching a polarity sensitive fluorescent probe to a site on the protein that is allosterically responsive to glucose binding. Correspondingly, the resulting optical biosensor has micromolar sensitivity to glucose. Because binding is reversible, the biosensor is reusable and can be stored at 4 degrees C for 6 months without losing its sensitivity. In this paper, we show the feasibility of using the GBP biosensor to monitor glucose in microdialysis. The effect of perfusion rate, bulk glucose concentration and temperature on microdialysis efficiency was determined. Additionally, the glucose concentrations in mammalian cell culture were monitored to demonstrate the applicability of this sensor in complex and dynamic processes over a period of time. As the sensor is sensitive to micromolar glucose, high dialysis efficiency is not required when the bulk glucose concentration is within the millimolar physiological range. Thus, a perfusion rate of 10 microL/min or faster can be used, resulting in delay times of 1 min or less.
Collapse
|
38
|
Ge X, Lam H, Modi SJ, LaCourse WR, Rao G, Tolosa L. Comparing the performance of the optical glucose assay based on glucose binding protein with high-performance anion-exchange chromatography with pulsed electrochemical detection: efforts to design a low-cost point-of-care glucose sensor. J Diabetes Sci Technol 2007; 1:864-72. [PMID: 19885158 PMCID: PMC2769676 DOI: 10.1177/193229680700100610] [Citation(s) in RCA: 13] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
BACKGROUND The glucose binding protein (GBP) is one of many soluble binding proteins found in the periplasmic space of gram-negative bacteria. These proteins are responsible for chemotactic responses and active transport of chemical species across the membrane. Upon ligand binding, binding proteins undergo a large conformational change, which is the basis for converting these proteins into optical biosensors. METHODS The GBP biosensor was prepared by attaching a polarity-sensitive fluorescent probe to a single cysteine mutation at a site on the protein that is allosterically responsive to glucose binding. The fluorescence response of the resulting sensor was validated against high-performance anion-exchange chromatography (HPAEC) with pulsed electrochemical detection. Finally, a simple fluorescence reader was built using a lifetime-assisted ratiometric technique. RESULTS The GBP assay has a linear range of quantification of 0.100-2.00 microM and a sensitivity of 0.164 microM(-1) under the specified experimental conditions. The comparison between GBP and HPAEC readings for nine blind samples indicates that there is no statistical difference between the analytical results of the two methods at the 95% confidence level. Although the methods of fluorescence detection are based on different principles, the response of the homemade device to glucose concentrations was comparable to the response of the larger and more expensive tabletop fluorescence spectrophotometer. CONCLUSIONS A glucose binding protein labeled with a polarity-sensitive probe can be used for measuring micromolar amounts of glucose. Using a lifetime-assisted ratiometric technique, a low-cost GBP-based micromolar glucose monitor could be built.
Collapse
|
39
|
Kostov Y, Smith DS, Tolosa L, Rao G, Gryczynski I, Gryczynski Z, Malicka J, Lakowicz JR. Directional surface plasmon-coupled emission from a 3 nm green fluorescent protein monolayer. Biotechnol Prog 2006; 21:1731-5. [PMID: 16321058 PMCID: PMC6949142 DOI: 10.1021/bp050114k] [Citation(s) in RCA: 27] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
Abstract
High-sensitivity detection schemes are of great interest for a number of applications. Unfortunately, such schemes are usually high-cost. We demonstrate a low-cost approach to a high-sensitivity detection scheme based on surface plasmon-coupled emission (SPCE). The SPCE of a monomolecular layer of green fluorescent protein (GFP) is reported here. The protein was electrostatically attached to a thin, SiO(2)-protected silver film deposited on a quartz substrate. The visible, directional emission of GFP was observed at a sharp, well-defined angle of 47.5 degrees from the normal to the coupling prism, and the spectrum corresponded to that of GFP. The SPCE resulting from the reverse Kretschmann configuration showed a 12-fold enhancement over the free space fluorescence. The directional emission was 97% p-polarized. The directionality and high polarization can be coupled with the intrinsic spectral resolution of SPCE to be used in the design miniaturized spectrofluorometers. The observation of SPCE in the visible region of the spectrum from a monolayer of protein opens up new possibilities in protein-based sensing.
Collapse
|
40
|
Bartolome A, Bardliving C, Rao G, Tolosa L. Fatty acid sensor for low-cost lifetime-assisted ratiometric sensing using a fluorescent fatty acid binding protein. Anal Biochem 2005; 345:133-9. [PMID: 16137630 DOI: 10.1016/j.ab.2005.07.030] [Citation(s) in RCA: 16] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/04/2005] [Revised: 07/14/2005] [Accepted: 07/21/2005] [Indexed: 11/26/2022]
Abstract
Elevated free fatty acid (FA) levels lead to insulin resistance, hypertension, and microangiopathy, all of which are associated with type 2 diabetes. On the other hand, deficiencies of FA are indicative of certain neurodegenerative diseases, including autism. Thus, free FA levels are a diagnostic indicator for a variety of disorders. Here we describe the use of a commercially available FA binding protein labeled with acrylodan (ADIFAB), which we modified with a ruthenium metal-ligand complex with the intention of creating a low-cost FA sensor. The dual-labeled FA binding protein was used in lifetime-assisted ratiometric sensing (LARS) of oleic acid. For both steady-state and time-resolved luminescence decay experiments, the protein is responsive to oleic acid in the range of 0.02-4.7 microM. The emission at 432 nm, which is associated with the acrylodan occupying the FA binding site, decreases in intensity and red shifts to 505 nm on the addition of oleic acid. The intensities of the 505-nm peak due to the acrylodan displaced from the binding site by FA and of the 610-nm emission peak of ruthenium remained nearly unchanged. Fitting of the fluorescence decay data using the method of least squares revealed three emitting components with lifetimes of approximately 0.60, 4.00, and 370 ns. Fractional intensities of the emitting species indicate that changes in modulation between 2 and 10 MHz on binding of the protein with oleic acid are due mainly to the 4.00-ns component. The 0.60- and 370-ns components are assigned to acrylodan (505 nm) and ruthenium, respectively. Note that because ruthenium has a lifetime that is two orders of magnitude longer than that of acrylodan, the FA measurements were carried out at excitation frequencies lower than what can be done with acrylodan alone. Thus, low-cost instrumentation can be designed for a practical FA sensor without sacrificing the quality of measurements.
Collapse
|
41
|
Ge X, Tolosa L, Simpson J, Rao G. Genetically engineered binding proteins as biosensors for fermentation and cell culture. Biotechnol Bioeng 2004; 84:723-31. [PMID: 14595785 DOI: 10.1002/bit.10830] [Citation(s) in RCA: 23] [Impact Index Per Article: 1.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
Abstract
The signal-transduction properties and the potential applications of two engineered binding proteins from E. coli were extensively studied. Both proteins have a single cysteine mutation in their polypeptide chains, which allow the introduction of an environmentally sensitive fluorophore: ANS for glucose-binding protein (GBP) and acrylodan for glutamine-binding protein (QBP). Both proteins respond to their ligands in the micromolar range. The proteins can be stored at 4 degrees C for at least 5 months. Apparent binding constant, protein concentration, and fluorophore are three major factors that affect the biosensor's responsive ranges. The binding of the ligand is quick and reversible in solution, but the unfavorable dissociation equilibrium and mass-transfer resistance for encapsulated proteins can delay the response to several minutes and the recovery to hours. Simulated results show that using dialysis tubing with a diameter of 1 mm or less is possible to reduce the recovery time to less than 30 minutes. The potential applications of GBP were studied in yeast fermentation and E. coli fermentations in three different scales: 150 mL, 5 mL, and 100 microL. The results were compared with an YSI 2700 Chemistry Analyzer. Although the latter could not give reliable results for the E. coli fermentations as the glucose concentration in LB medium is close to its lower detection limit, the glucose biosensor presented here was successfully applied to each situation. Glutamine-binding protein was tested in cell cultures of two different scales (100 mL and 100 microL) and the results were also compared with those obtained with YSI. Both QBP and YSI gave good results for the 100-mL cell culture, but the relatively large sample volume requirement of YSI (at least 5 microL) prevented it from being used in the 100-microL cell culture. Because of their small sample volume requirements (less than 1 microL) and high sensitivity, the assays described here might find wide applications in high-throughput bioprocessing.
Collapse
|
42
|
Ge X, Tolosa L, Rao G. Dual-Labeled Glucose Binding Protein for Ratiometric Measurements of Glucose. Anal Chem 2004; 76:1403-10. [PMID: 14987097 DOI: 10.1021/ac035063p] [Citation(s) in RCA: 73] [Impact Index Per Article: 3.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/30/2022]
Abstract
Highly sensitive glucose monitoring has potential applications in conditions where the glucose levels are below the detection limit of currently available technology. Examples include bioprocess monitoring of bacterial cultures and measurement of minute amounts of human interstitial fluid extracted by iontophoresis. Here we describe a ratiometric glucose sensor capable of measuring micromolar levels of glucose. This sensor is based on an E. coli glucose binding protein (GBP) labeled with two fluorophores. The L255C mutant of GBP was labeled with the environment-sensitive fluorophore, acrylodan, at the cysteine mutation and a long-lived metal ligand complex of ruthenium (ruthenium bis(2,2'-bipyridyl)-1, 10-phenanthroline-9-isothiocyanate) at the N-terminal. The acrylodan emission is quenched in the presence of glucose while the ruthenium emission remained constant, thereby serving as a reference. The sensitivity of the sensor is in the micromolar range (K(d) = 0.4-1.4 microM). Thus, it is possible to measure glucose concentrations at micromolar levels and higher (with dilution). Calculations of the fluorescence energy-transfer efficiency between acrylodan and ruthenium gave an approximate distance of 25 A between the two fluorophores, consistent with X-ray crystallographic data. The effect of temperature on glucose binding was measured and analyzed. Maximum signal changes and apparent binding constants increase with temperature. The enthalpy change for glucose binding as calculated from the apparent binding constants is approximately 43.1 kJ/mol. In addition to ratiometric measurements, the presence of the long-lived ruthenium metal ligand complex allows for low-cost modulation-based sensing.
Collapse
|
43
|
Tolosa L, Ge X, Rao G. Reagentless optical sensing of glutamine using a dual-emitting glutamine-binding protein. Anal Biochem 2003; 314:199-205. [PMID: 12654305 DOI: 10.1016/s0003-2697(02)00586-9] [Citation(s) in RCA: 32] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
Abstract
Glutamine is a major source of nitrogen and carbon in cell culture media. Thus, glutamine monitoring is important in bioprocess control. Here we report a reagentless fluorescence sensing for glutamine based on the Escherichia coli glutamine-binding protein (GlnBP) that is sensitive in the submicromolar ranges. The S179C variant of GlnBP was labeled at the -SH and N-terminal positions with acrylodan and ruthenium bis-(2,2'-bipyridyl)-1,10-phenanthroline-9-isothiocyanate, respectively. The acrylodan emission is quenched in the presence of glutamine while the ruthenium acts as a nonresponsive long-lived reference. The apparent binding constant, K'(d), of 0.72 microM was calculated from the ratio of emission intensities of acrylodan and ruthenium (I(515)/I(610)). The presence of the long-lived ruthenium allowed for modulation sensing at lower frequencies (1-10 MHz) approaching an accuracy of +/-0.02 microM glutamine. Dual-frequency ratiometric sensing was also demonstrated. Finally, the extraordinary sensitivity of GlnBP allows for dilution of the sample, thereby eliminating the effects of background fluorescence from the culture media.
Collapse
|
44
|
Tolosa L, Kostov Y, Harms P, Rao G. Noninvasive measurement of dissolved oxygen in shake flasks. Biotechnol Bioeng 2002; 80:594-7. [PMID: 12355471 DOI: 10.1002/bit.10409] [Citation(s) in RCA: 60] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/06/2022]
Abstract
Shake flasks are ubiquitous in cell culture and fermentation. However, conventional devices for measuring oxygen concentrations are impractical in these systems. Thus, there is no definitive information on the oxygen supply of growing cells. Here we report the noninvasive, nonintrusive monitoring of dissolved oxygen (DO) in shake flasks using a low-cost optical sensor. The oxygen-sensitive element is a thin, luminescent patch affixed to the inside bottom of the flask. The sensitivity and accuracy of this device is maximal up to 60% DO, within the range that is critical to cell culture applications. By measuring actual oxygen levels every 1 or 5 min throughout the course of yeast and E. coli fermentations, we found that a modest increase in shaker speed and a decrease in culture volume slowed the onset of oxygen limitation and reduced its duration. This is the first time that in situ oxygen limitation is reported in shake flasks. The same data is unattainable with a Clark type electrode because the presence of the intrusive probe itself changes the actual conditions. Available fiber optic oxygen sensors require cumbersome external connections and recalibration when autoclaved.
Collapse
|
45
|
Murtaza Z, Tolosa L, Harms P, Lakowicz JR. On the Possibility of Glucose Sensing Using Boronic Acid and a Luminescent Ruthenium Metal-Ligand Complex. J Fluoresc 2002; 12:187-192. [PMID: 32377061 PMCID: PMC7202357 DOI: 10.1023/a:1016800515030] [Citation(s) in RCA: 13] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022]
Abstract
We describe a new approach to optical sensing of glucose based on the competitive interactions between a ruthenium metal ligand complex, a boronic acid derivative and glucose. The metal-ligand complex [Ru(2,2'-bipyridme)2(5,6-dihydroxy-1,10-phenanthrolme)](PF6)2 at pH 8 forms a reversible complex with 2-toluylboronic acid or 2-methoxyphenyl boronic acid. Complexation is accompanied by a several-fold increase in the luminescent intensity of the ruthenium complex. Addition of glucose results in decreased luminescent intensity, which appears to be the result of decreased binding between the metal-ligand complex and the boronic acid. Ruthenium metal-ligand complexes are convenient for optical sensing because their long luminescent decay times allow lifetime-based sensing with simple instrumentation.
Collapse
|
46
|
Lakowicz JR, Gryczynski I, Piszczek G, Tolosa L, Nair R, Johnson ML, Nowaczyk K. Microsecond dynamics of biological macromolecules. Methods Enzymol 2001; 323:473-509. [PMID: 10944765 DOI: 10.1016/s0076-6879(00)23379-x] [Citation(s) in RCA: 21] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/06/2023]
|
47
|
Lakowicz JR, Gryczynski I, Gryczynski Z, Tolosa L, Randers-Eichhorn L, Rao G. Polarization-based sensing of glucose using an oriented reference film. JOURNAL OF BIOMEDICAL OPTICS 1999; 4:443-9. [PMID: 23014617 PMCID: PMC6938719 DOI: 10.1117/1.429955] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/01/2023]
Abstract
We describe a new approach to glucose sensing using polarization measurements in the presence of a stretch-oriented reference film. The method relies on measurement of the polarized emission from the reference film and of a fluorophore which changes intensity in response to glucose. A glucose-sensitive fluorescent signal was provided by the glucose/galactose binding protein from E. coli. This protein was labeled with an environmentally sensitive fluorophore at a single genetically inserted cysteine residue, and displayed decreased fluorescence upon glucose binding. Using the protein and the reference film we observed glucose-sensitive polarization values for micromolar glucose concentrations. This method of polarization-based sensing is generic and can be used for any sensing fluorophore which displays a change in intensity. In principle, one can construct simple and economical devices for this type of glucose measurement. © 1999 Society of Photo-Optical Instrumentation Engineers.
Collapse
|
48
|
Lakowicz JR, Gryczynski I, Gryczynski Z, Tolosa L, Dattelbaum JD, Rao G. Polarization-Based Sensing with a Self-Referenced Sample. APPLIED SPECTROSCOPY 1999; 53:1149-1157. [PMID: 32255815 PMCID: PMC7133461 DOI: 10.1366/0003702991947964] [Citation(s) in RCA: 8] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/11/2023]
Abstract
We describe a new method of fluorescence sensing based on fluorescence polarization. The sensor consists of two compartments, both of which contain the sensing fluorophore. One side of the sensor contains a constant concentration of analyte, and the other contains the unknown concentration. Emission from both sides is observed through polarizers, with the polarization from the sample being rotated 90° from that of the reference. Changes in the fluorescence intensity of the sample result in changes in the measured polarization for the combined emission. We show that this approach can be used to measure glucose and calcium using fluorophores which show analyte-dependent intensity changes, and no change in the spectral shape. Only a single fluorophore is required, this being the sensing fluorophore in both sides of the sensor. We also show that polarization sensing of glucose and calcium can be performed with visual detection of the polarization. In this case the only electronic component is the light source. These simple schemes can be used with a variety of analytes. The only requirement is a change in fluorescence intensity in response to the analyte.
Collapse
|
49
|
Tolosa L, Gryczynski I, Eichhorn LR, Dattelbaum JD, Castellano FN, Rao G, Lakowicz JR. Glucose sensor for low-cost lifetime-based sensing using a genetically engineered protein. Anal Biochem 1999; 267:114-20. [PMID: 9918662 PMCID: PMC6905191 DOI: 10.1006/abio.1998.2974] [Citation(s) in RCA: 129] [Impact Index Per Article: 5.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/22/2022]
Abstract
We describe a glucose sensor based on a mutant glucose/galactose binding protein (GGBP) and phase-modulation fluorometry. The GGBP from Escherichia coli was mutated to contain a single cysteine residue at position 26. When labeled with a sulfhydryl-reactive probe 2-(4'-iodoacetamidoanilino)naphthalene-6-sulfonic acid, the labeled protein displayed a twofold decrease in intensity in response to glucose, with a dissociation constant near 1 microM glucose. The ANS-labeled protein displayed only a modest change in lifetime, precluding lifetime-based sensing of glucose. A modulation sensor was created by combining ANS26-GGBP with a long-lifetime ruthenium (Ru) metal-ligand complex on the surface of the cuvette. Binding of glucose changed the relative intensity of ANS26-GGBP and the Ru complex, resulting in a dramatic change in modulation at a low frequency of 2.1 MHz. Modulation measurements at 2.1 MHz were shown to accurately determine the glucose concentration. These results suggest an approach to glucose sensing with simple devices.
Collapse
|
50
|
Lakowicz JR, Gryczynski I, Tolosa L, Dattelbaum JD, Castellano FN, Li L, Rao G. ADVANCES IN FLUORESCENCE SPECTROSCOPY: MULTI-PHOTON EXCITATION, ENGINEERED PROTEINS, MODULATION SENSING AND MICROSECOND RHENIUM METAL-LIGAND COMPLEXES. ACTA PHYSICA POLONICA: A 1999; 95:179-195. [PMID: 31660002 PMCID: PMC6816252 DOI: 10.12693/aphyspola.95.179] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/10/2023]
Abstract
The technology and applications of fluorescence spectroscopy are rapidly advancing. In this overview presentation we summarize some recent developments from this laboratory. Two and three-photon excitation have been observed for a wide variety of intrinsic and extrinsic fluorophores, including tryptophan, tyrosine, DNA stains, membrane probes, and even alkanes. It has been possible to observe multi-photon excitation of biopolymers without obvious photochemical or photo-thermal effects. Although not de-scribed in our lecture, another area of increasing interest is the use of engineered proteins for chemical and clinical sensing. We show results for the glucose-galactose binding protein from E. coli. The labeled protein shows spectral changes in response to micromolar concentrations of glucose. This protein was used with a novel sensing method based on the modulated emission of the labeled proteins and a long lifetime reference fluorophore. And finally, we describe a recently developed rhenium complex which displays a lifetime near 3 µs in oxygenated aqueous solution. Such long life-time probes allow detection of microsecond dynamic processes, bypassing the usual nanosecond timescale limit of fluorescence. The result of these developments in protein engineering, sensing methods, and metal-ligand probe chemistry will be the increased use of fluorescence in clinical chemistry and point-of-care analyses.
Collapse
|