The effect of pressure pad location of spinal orthosis on the treatment of adolescent idiopathic scoliosis (AIS)

Patient with moderate AIS is usually prescribed with spinal orthosis aiming to mechanically support and prevent the spine from further deterioration. In the conventional fitting method, pre-brace X-ray is the main reference, thus, the pressure pad of spinal orthosis may not be accurately located to the strategic areas because the spinal deformities could change 3-dimensionally once pressure pad is applied. A high correlation (r > 0.98) between Cobb's angle and spinous process angle (SPA) was found in the recent studies. With the advancements of 3D clinical ultrasound (3D CUS), tracing SPA along a scoliotic spine becomes possible and this can be used to estimate Cobb's angle. This study aimed to evaluate the effect of pressure pad location of spinal orthosis in the treatment of AIS and 3D CUS was used to trace SPA for estimation of Cobb's angle. The in-brace X-rays were assessed for confirmation of treatment effectiveness. The subjects were divided into ultrasound-guided fitting group A (n=21) and conventional fitting group B (n=22). In the group A, pressure pads were tested at 5 locations - the prescribed location as in the conventional fitting (referred to the pre-brace X-ray), and 1 cm and 2 cm above and below the prescribed location, and 3D CUS was applied to trace the SPA in these 5 pad locations, and the pad location with the lowest estimated Cobb's angle was selected in the final fitting. The assessments of in-brace X-rays showed that the mean Cobb's angle of group A decreased from 28.9° (pre-brace) to 18.6° (immediate in-brace) while the mean Cobb's angle of group B decreased from 27.1° (pre-brace) to 22.5° (immediate in-brace). There was a significant difference (p < 0.05) in the correction of Cobb's angle between the two groups. The results showed that accurate pressure pad location does play an important role in the reduction of Cobb's angle and 3D CUS can be considered as a non-invasive and effective assessment tool to improve orthotic treatment of AIS.

The influence of the precursor and synthesis method on the CO2 capture capacity of carpet waste-based sorbents

Adsorption is one of the most promising technologies for reducing CO(2) emissions and at present several different types of sorbents are being investigated. The use of sorbents obtained from low-cost and abundant precursors (i.e. solid wastes) appears an attractive strategy to adopt because it will contribute to a reduction not only in operational costs but also in the amount of waste that is dumped and burned in landfills every year. Following on from previous studies by the authors, in this work several carbon-based adsorbents were developed from different carpet wastes (pre-consumer and post-consumer wastes) by chemical activation with KOH at various activation temperatures (600-900 °C) and KOH:char impregnation ratios (0.5:1 to 4:1). The prepared materials were characterised by chemical analysis and gas adsorption (N(2), -196 °C; CO(2), 0 °C), and tested for CO(2) adsorption at temperatures of 25 and 100 °C. It was found that both the type of precursor and the conditions of activation (i.e. impregnation ratios, and activation temperatures), had a huge influence on the microporosity of the resultant samples and their CO(2) capture capacities. The carbon-based adsorbent that presented the maximum CO(2) capture capacities at 25 and 100 °C (13.8 wt.% and 3.1 wt.%, respectively), was prepared from a pre-consumer carpet waste and was activated at 700 °C using a KOH:char impregnation ratio of 1:1. This sample showed the highest narrow microporosity volume (0.47 cm(3) g(-1)), thus confirming that only pores of less than 1 nm are effective for CO(2) adsorption at atmospheric pressure.

Size-effect induced short-range magnetic ordering in germanium nanostructures

Formation of ordered magnetic states in germanium nanostructures embedded in SiO2 has been investigated. Samples with the nanostructures were prepared by sputtering deposition on Si(100) substrates, followed by thermal annealing in vacuum. Transmission electron microscopy, energy dispersive X-ray spectrometry, and Raman spectroscopy have been used to characterize the samples. Magnetic measurements were performed using a superconducting quantum interference device. Size-effect induced magnetic orderings in the germanium nanostructures were found to be present at room temperatures and below. Superparamagnetic behavior was observed at temperatures above 230 K, whereas thermal excitation of spin reorientation and magnetic coupling has been revealed at temperatures below 60 K. Inverted hysteresis loops with negative remanences and multiple plateaus revealed the ferri- or antiferromagnetic nature of the coupling. Inter-domain coupling and effect of magnetic anisotropy will be discussed based on the experimental results and simulations with a spin reorientation model.

Application of 3-D ultrasound in assisting the fitting procedure of spinal orthosis to patients with adolescent idiopathic scoliosis

Spinal orthosis is generally applied to the patients with adolescent idiopathic scoliosis (AIS) during puberty to mechanically support the spine and prevent further deterioration. However, the optimum location of pressure is not easy to be determined and the X-ray taken is not a real time presentation of the spinal curvature. With the advancement of clinical ultrasound, tracing spinal processes along a scoliotic spine becomes possible, which means spinous process angle (SPA) can be obtained from ultrasound images. Moreover, SPA is found to be highly correlated with Cobb's angle. Since the outcome of orthotic intervention for AIS is considered to be associated with accurate orthosis fitting, this study seeks to apply three-dimensional (3-D) ultrasound in the fitting procedure of spinal orthosis for patients with AIS. The accuracy of pressure pad location in brace can help to improve the effectiveness of spinal orthosis treatment. By means of the ultrasound assessments, spinous process angle is examined and used as the parameter to evaluate the optimal location for pressure pad. The intra-rater reliability [ICC (1, 3)] for using ultrasound to measure SPA is >0.9 (p<0.05). Furthermore, the correlation between Cobb's angle estimated from the measurement of SPA in 3-D ultrasound images and Cobb's angle measured from X-ray is highly significant (R=0.98, p<0.01). According to these findings, ultrasound can be further developed as a non-invasive real-time assessment tool for spinal curvature especially in fitting stage to improve the treatment effect of the spinal orthosis.

Use of closed controlled subcutaneous drainage to manage chronic lower limb oedema in patients with advanced cancer

Chronic lower limb oedema is common in patients with advanced cancer and can be difficult to manage. In this paper, we present two patients who had severe cancer-related chronic lower limb oedema which was refractory to conventional therapy. It was satisfactorily managed using closed controlled subcutaneous drainage without any skin infections or complications. We also review the prevalence, diagnosis, and management of cancer-related chronic oedema and lymphoedema.

A lipid extract of Perna canaliculus affects the expression of pro-inflammatory cytokines in a rat adjuvant-induced arthritis model

As published initially in this same journal in 2000, the lipid extract of Perna canaliculus (New Zealand green-lipped mussel; Lyprinol) is known for its anti-inflammatory effects in animal models and in human controlled studies (arthritis; asthma). As a follow-up of its effects on pain in a rat model of adjuvant-induced arthritis (ALA), we studied its effects on the production of cytokines known to be associated with inflammation (IL-6, IL-1alpha TNF-alpha, IFN-gamma). Feeding with Lyprinol was associated with significantly decreased expression levels of TNF-alpha and IFN-gamma when compared to Naproxen (positive control) and, even more when compared with sham and extra-virgin olive oil (negative control). When compared to Naproxen, sham and extra-virgin olive oil, the levels of IL-6 and IL-1alpha were also marginally decreased in rats fed with Lyprinol. This study demonstrates that AIA rats fed with Lyprinol had decreased production ofcytokines associated with inflammation.

Localization of hRad9 in breast cancer

Background

hRad9 is a cell cycle checkpoint gene that is up-regulated in breast cancer. We have previously shown that the mRNA up-regulation correlated with tumor size and local recurrence. Immunohistochemical studies were made to better define the role of hRad9 in breast carcinogenesis.

Methods

Localisation of hRad9 protein were performed on paired tumor and normal breast tissues. Immunoblotting with and without dephosphorylation was used to define the protein isolated from breast cancer cells.

Results

Increased hRad9 protein was observed in breast cancer cells nucleus compared to non-tumor epithelium. This nuclear protein existed in hyperphosphorylated forms which may be those of the hRad9-hRad1-hHus1 complex.

Conclusion

Finding of hyperphosphorylated forms of hRad9 in the nucleus of cancer cells is in keeping with its function in ameliorating DNA instability, whereby it inadvertently assists tumor growth.

In vitro behavior of osteoblast-like cells on PLLA films with a biomimetic apatite or apatite/collagen composite coating

To investigate the methods to improve the cell-material interaction of devices or tissue engineering scaffolds made of poly(L-lactic acid) (PLLA) polymer, apatite and apatite/collagen composite coatings were formed on PLLA films within 24 h through accelerated biomimetic processes. In vitro investigation using Saos-2 osteoblast-like cells through cell culture was conducted to assess the biological performance of these biomimetic coatings. The cell morphology on three types of surfaces, viz., PLLA film, PLLA film with the apatite coating, and PLLA film with the apatite/collagen composite coating, was studied using scanning electron microscopy (SEM). Cell viability was estimated using the MTT assay. The differentiated cell function was assessed by measuring the alkaline phosphatase (ALP) activity. The results obtained indicated that the biomimetic apatite and apatite/collagen composite coatings could significantly enhance the proliferation and differentiation of osteoblast-like cells. The apatite/collagen composite coating appears to be promising for the surface modification of PLLA-based devices with much improved interactions with osteoblastic cells.

The effect of rigid versus flexible spinal orthosis on the gait pattern of patients with adolescent idiopathic scoliosis

The conventional rigid spinal orthosis and the flexible spinal orthosis, SpineCor, have different treatment principles in the management of adolescent idiopathic scoliosis (AIS). These may influence the patients' gait pattern and clinical outcome. In this study, gait analysis on patients with AIS undergoing these two orthotic interventions were conducted. The patients' lower limb kinematic and kinetic data during level walking were collected using a motion analysis system and two force platforms in four test conditions: pre-intervention, having used the orthosis for 1 month and 1 year (in and out of the orthosis). Twenty-one subjects were randomly assigned to the rigid spinal orthosis group (10 subjects) and the SpineCor group (11 subjects). Neither group showed gait asymmetry when comparing the convex and concave sides in the four test conditions. However, significant reduction in the range of motion of the pelvis and hip joints in the coronal plane were found. Although patients with AIS undergoing these two orthotic interventions showed significant changes in walking pattern within the study period, their long-term effect on gait and function requires further investigation through long-term prospective studies.

The effect of backpack weight on the standing posture and balance of schoolgirls with adolescent idiopathic scoliosis and normal controls

Concerns have been raised regarding the effect of carrying a backpack on adolescent posture and balance, but the effect of backpack loading combined with other factors affecting balance, such as adolescent idiopathic scoliosis (AIS), has not been determined. This study examines the effects of backpack load on the posture and balance of schoolgirls with AIS and normal controls. The standing posture of 26 schoolgirls with mild AIS (mean age 13, Cobb angle 10-25 degrees ) and 20 age-matched normal schoolgirls were recorded without a backpack and while carrying a standard dual-strap backpack loaded at 7.5%, 10%, 12.5% and 15% of the subject's bodyweight (BW). Kinematics of the pelvis, trunk and head were recorded using a motion analysis system and centre of pressure (COP) data were recorded using a force platform. Reliable COP data could only be derived for 13 of the subjects with AIS. Increasing backpack load causes a significantly increased flexion of the trunk in relation to the pelvis and extension of the head in relation to the trunk, as well as increased antero-posterior range of COP motion. While backpack load appears to affect balance predominantly in the antero-posterior direction, differences between groups were more evident in the medio-lateral direction, with AIS subjects showing poor balance in this direction. Overall, carrying a backpack causes similar sagittal plane changes in posture and balance in both normal and AIS groups. Load size or subject group did not influence balance, but the additive effect of backpack carrying and AIS on postural control alters the risk of fall in this population. Therefore, load limit recommendations based on normal subjects should not be applicable to subjects with AIS.

Curve correction effect of rigid spinal orthosis in different recumbent positions in adolescent idiopathic scoliosis (AIS): a pilot MRI study

In this pilot cross-sectional study, the effectiveness of rigid spinal orthoses in the correction of spinal curvature of 14 patients with moderate adolescent idiopathic scoliosis (AIS) at different recumbent positions (supine, prone, right and left decubitus) was investigated. Using magnetic resonance (MR) imaging and multi-planar reconstruction technique, evaluation of the scoliotic spine in the coronal, sagittal and axial planes and the effect of spinal orthosis on AIS at different recumbent positions was studied. There was significant reduction of coronal Cobb's angle (p < 0.05) with bracing at all four recumbent positions and the maximal reduction was found in the prone position (18% reduction). The sagittal Cobb's angle was only significantly reduced at the supine position while the axial rotation did not change significantly in all positions.

A comparison of the clinical effectiveness of spinal orthoses manufactured using the conventional manual method and CAD/CAM method in the management of AIS

Spinal orthoses are commonly prescribed to patients with moderate AIS for prevention of further deterioration. In a conventional manufacturing method, plaster bandages are used to get patient's body contour and plaster cast is rectified manually. With the introduction of CAD/CAM system, a series of automated processes from body scanning to digital rectification and milling of positive model can be performed in a fast and accurate fashion. This project is to study the impact of CAD/CAM method as compared with the conventional method. In assessing the 147 recruited subjects fitted with spinal orthoses (43 subjects using conventional method and 104 subjects using CAD/CAM method), significant decreases (p<0.05) were found in the Cobb angles when comparing the pre-intervention data with that of the first year of intervention. Regarding the learning curve, Orthotists are getting more competent with the CAD/CAM technique in four years time. The mean productivity of the CAD/CAM method is 2.75 times higher than that of the conventional method. The CAD/CAM method could achieve similar clinical outcomes and with its high efficiency, could be considered as substitute for conventional methods in fabricating spinal orthoses for patients with AIS.

Effects of backpack loading on the pulmonary capacities of normal schoolgirls and those with adolescent idiopathic scoliosis

STUDY DESIGN

A prospective evaluation of the effects of backpack carriage on the pulmonary function of schoolgirls without spinal deformity versus those with adolescent idiopathic scoliosis (AIS).

OBJECTIVE

To establish if recommended backpack load limits for normal schoolchildren are also appropriate for study participants with AIS.

SUMMARY OF BACKGROUND DATA

The weight of schoolchildren's backpacks are of concern because of effects including compromise of pulmonary function. Impaired pulmonary function is also found with AIS, but the effect of backpack carriage on the respiratory parameters of schoolchildren with AIS has not previously been examined.

METHODS

Forced vital capacity (FVC), forced expiratory volume (FEV1), peak expiratory flow (PEF), and forced expiratory flow (FEF25-75%) were recorded in 17 girls (mean age, 12 years) with moderate AIS (Cobb angle, 26 degrees-50 degrees) and 18 girls (mean age, 11 years) without musculoskeletal deformity during carriage of a backpack loaded at 0%, 5%, 7.5%, 10%, 12.5%, and 15% body weight in random order. Absolute values and proportions of reference values were analyzed by repeated-measures analysis of variance. RESULTS.: No interaction between load and group was found, indicating that backpack loading has a similar effect on the pulmonary function of both normal and AIS groups. However, all recorded pulmonary parameters were found to be significantly lower in the AIS than normal group, significantly so for the referenced FVC and PEF. A significant decrease in FVC and FEV1 was found with increasing backpack load, and the load at which these changes were found to be significant was lower than those established in previous studies.

CONCLUSIONS

Pulmonary function may be more sensitive to backpack load than previously considered, especially when study participants with AIS are being considered, and the recommended loading limit of 10% body weight may not be applicable to schoolgirls with AIS.

Molecular mechanisms of survival and apoptosis in RAW 264.7 macrophages under oxidative stress

Organisms living in an aerobic environment are continuously exposed to reactive oxygen species (ROS). Apoptosis of cells can be induced by ROS and cells also develop negative feedback mechanisms to limit ROS induced cell death. In this study, RAW264.7 murine macrophage cells were treated with H(2)O(2) and cDNA microarray technique was used to produce gene expression profiles. We found that H(2)O(2) treatment caused up-regulation of stress, survival and apoptosis related genes, and down-regulation of growth and cell cycle promoting genes. Numerous genes of metabolism pathways showed special expression patterns under oxidative stress: glycolysis and lipid synthesis related genes were down-regulated whereas the genes of lipid catabolism and protein synthesis were up-regulated. We also identified several signaling molecules as ROS-responsive, including p53, Akt, NF-kappa B, ERK, JNK, p38, PKC and INF-gamma . They played important roles in the process of apoptosis or cell survival. Finally, an interactive pathway involved in cellular response to oxidative stress was proposed to provide some insight into the molecular events of apoptosis induced by ROS and the feedback mechanisms involved in cell survival.

The effect of load carriage on the gait of girls with adolescent idiopathic scoliosis and normal controls

Adolescent idiopathic scoliosis (AIS) and load-bearing both appear to place similar demands on gait, but no data regarding the combined effects of load-bearing gait in subjects with AIS could be found. The gait patterns of 22 normal adolescent girls and 28 girls with mild AIS (Cobb angle<25 degrees ) were recorded at backpack loads of 0, 7.5, 10, 12.5 and 15% body weight. Temporal-distance and joint kinematic, moment and power parameters were analyzed by repeated measures ANOVA. Findings showed that backpack carriage places an increased demand on the musculature of the lower limb and results in a gait characterized by reduced pelvic motion and greater hip flexion-extension. AIS has a generally similar effect on gait kinematics as backpack carriage, with AIS subjects having significantly longer double support durations, shorter single support durations and lower knee joint power generation and absorption than normal subjects. No interaction between backpack load and AIS was found however, although investigation of parameters indicating a critical response to load showed that this typically occurred at lower backpack loads (7.5% body weight) in the AIS group. Overall, both AIS and load-bearing place increased demands on gait, but carriage of a loaded backpack does not appear to cause any greater demand on subjects with AIS than normal controls.

The effect of backpack load on the gait of normal adolescent girls

Concerns regarding the effects of load carriage have led to recommendations that backpacks be limited to 10?-?15% of body weight, based on significant changes in physical performance. However, gait responses to backpack loads are not entirely consistent and there is a particular lack of data regarding load-bearing gait in adolescent females. Gait patterns of 22 normal adolescent girls were recorded at backpack loads of 0, 7.5, 10.0, 12.5 and 15.0% body weight. Temporal-distance, ground reaction force and joint kinematic, moment and power parameters were analysed by repeated measures ANOVA with factors of backpack load and side (left or right). Walking speed and cadence decreased significantly with increasing backpack load, while double support time increased. Kinematic changes were most marked at the proximal joints, with a decreased pelvic motion but a significant increase in the hip sagittal plane motion. Increased moments and power at the hip, knee and ankle showed increasing demand with backpack load. Parameters showed different responses to increasing load, and those that suggested a critical load indicated this to be approximately 10% body weight. While this may be due to a change in gait due to increased demand, further work is required to verify this and also to examine the cumulative effects of backpack load on the musculoskeletal system, which may be more appropriate in determining recommended load limits.

A comparison of treatment effectiveness between the CAD/CAM method and the manual method for managing adolescent idiopathic scoliosis

The treatment effectiveness of the CAD/CAM method and the manual method in managing adolescent idiopathic scoliosis (AIS) was compared. Forty subjects were recruited with twenty subjects for each method. The clinical parameters namely Cobb's angle and apical vertebral rotation were evaluated at the pre-brace and the immediate in-brace visits. The results demonstrated that orthotic treatments rendered by the CAD/CAM method and the conventional manual method were effective in providing initial control of Cobb's angle. Significant decreases (p < 0.05) were found between the pre-brace and immediate in-brace visits for both methods. The mean reductions of Cobb's angle were 12.8 degrees (41.9%) for the CAD/CAM method and 9.8 degrees (32.1%) for the manual method. An initial control of the apical vertebral rotation was not shown in this study. In the comparison between the CAD/CAM method and the manual method, no significant difference was found in the control of Cobb's angle and apical vertebral rotation. The current study demonstrated that the CAD/CAM method can provide similar result in the initial stage of treatment as compared with the manual method.

A work study of the CAD/CAM method and conventional manual method in the fabrication of spinal orthoses for patients with adolescent idiopathic scoliosis

A study was conducted to compare the CAD/CAM method with the conventional manual method in fabrication of spinal orthoses for patients with adolescent idiopathic scoliosis. Ten subjects were recruited for this study. Efficiency analyses of the two methods were performed from cast filling/ digitization process to completion of cast/image rectification. The dimensional changes of the casts/ models rectified by the two cast rectification methods were also investigated. The results demonstrated that the CAD/CAM method was faster than the conventional manual method in the studied processes. The mean rectification time of the CAD/CAM method was shorter than that of the conventional manual method by 108.3 min (63.5%). This indicated that the CAD/CAM method took about 1/3 of the time of the conventional manual to finish cast rectification. In the comparison of cast/image dimensional differences between the conventional manual method and the CAD/CAM method, five major dimensions in each of the five rectified regions namely the axilla, thoracic, lumbar, abdominal and pelvic regions were involved. There were no significant dimensional differences (p < 0.05) in 19 out of the 25 studied dimensions. This study demonstrated that the CAD/CAM system could save the time in the rectification process and offer a relatively high resemblance in cast rectification as compared with the conventional manual method.