Observation of CO Detection Using Aluminum-Doped ZnO Nanorods on Microcantilever

An oscillating piezoresistive microcantilever (MC) coated with an aluminum (Al)-doped zinc oxide (ZnO) nanorods was used to detect carbon monoxide (CO) in air at room temperature. Al-doped ZnO nanorods were grown on the MC surface using the hydrothermal method, and a response to CO gas was observed by measuring a resonant frequency shift of vibrated MC. CO gas response showed a significant increase in resonant frequency, where sensitivity in the order of picogram amounts was obtained. An increase in resonant frequency was also observed with increasing gas flow rate, which was simultaneously followed by a decrease in relative humidity, indicating that the molecular interface between ZnO and H₂O plays a key role in CO absorption. The detection of other gases of carbon compounds such as CO₂ and CH₄ was also performed; the sensitivity of CO was found to be higher than those gases. The results demonstrate the reversibility and reproducibility of the proposed technique, opening up future developments of highly sensitive CO-gas detectors with a fast response and room temperature operation.

Highly Rectifying Heterojunctions Formed by Annealed ZnO Nanorods on GaN Substrates

We study the effect of thermal annealing on the electrical properties of the nanoscale p-n heterojunctions based on single n-type ZnO nanorods on p-type GaN substrates. The ZnO nanorods are prepared by chemical bath deposition on both plain GaN substrates and on the substrates locally patterned by focused ion beam lithography. Electrical properties of single nanorod heterojunctions are measured with a nanoprobe in the vacuum chamber of a scanning electron microscope. The focused ion beam lithography provides a uniform nucleation of ZnO, which results in a uniform growth of ZnO nanorods. The specific configuration of the interface between the ZnO nanorods and GaN substrate created by the focused ion beam suppresses the surface leakage current and improves the current-voltage characteristics. Further improvement of the electrical characteristics is achieved by annealing of the structures in nitrogen, which limits the defect-mediated leakage current and increases the carrier injection efficiency.

Molecularly imprinted polymers-captivity ZnO nanorods for sensitive and selective detecting environmental pollutant

To develop the semiconductor of ZnO nanomaterials as the fluorescence sensor without leakage toxicity. Here, a molecularly imprinted polymer captivity ZnO nanorods (NRs) (MIPs-captivity ZnO NRs) was fabricated by precipitation polymerization. Such traditional technology was not only achieved the specific recognition for direct fluorescent quantification of the target tetracycline (TC) through fluorescence quenching, but also formed the shield to reduce the toxic effects of ZnO towards organisms. Under the optimized experimental conditions, the MIPs-captivity ZnO NRs were effectively applied to the direct fluorescence quantification of TC with excellent stability. Moreover, the practical analytical performance of the MIPs-captivity ZnO NRs was assayed by appraising the detection effects of TC in water sample from the Yangtze River with satisfactory results.

Influence of solvent molecular geometry on the growth of nanostructures

Solvent properties such as surface tension, dielectric constant, and viscosity have been extensively studied over more than 150 years to understand their influence on the growth kinetics of nanostructures. Interestingly, these nanoparticles-based studies have missed the influence of solvent molecular geometry. Herein, by synthesizing ZnO nanorods on a highly conductive nitrogen incorporated graphene oxide (N-GO) substrate, we present the first study showing the influence of solvent molecular geometry on the growth mechanism of nanostructures. The solvents such as water (N-GO-ZnO-W) allow a large number of functional atoms along a, b and c-axis to coordinate in all possible directions with the metal ions of wurtzite hexagonal crystal system of ZnO and thus leads to lower aspect ratio nanorods. On the contrary, the unavailability of binding sites along a-axis for solvents such as ethanol (N-GO-ZnO-E) provides a size-limiting effect and leads to preferred growth along b and c-axis, thus generating ZnO nanorods with a higher aspect ratio. The study shows that the number of interacting atoms, carbon chain length and the solvent molecular geometry influence the aspect ratio and therefore a solvent could be used to tune the nanostructures morphology and hence the performance of devices based on them.

Effect of silver doping on antidiabetic and antioxidant potential of ZnO nanorods

BACKGROUND

Increasing resistance to available drugs and their associated side-effects have drawn wide attention towards designing alternative therapeutic strategies for control of hyperglycemia and oxidative stress. The roles of the sizes and shapes of the nanomaterials used in the treatment and management of Type 2 Diabetes Mellitus (T2DM) in preventing chronic hyperglycaemia and oxidative stress are investigated. We report specifically on the effects of doping silver (Ag) into the ZnO nanorods (ZnO:Ag NR's) as a rational drug designing strategy.

METHODS

Inhibition of porcine pancreatic α-amylase, murine pancreatic amylase, α-glucosidase, murine intestinal glucosidase and amyloglucosidase are checked for evaluation of antidiabetic potential. In addition, the radical scavenging activities of ZnO:Ag NR's against nitric oxide, DDPH and superoxide radicals are evaluated.

RESULTS

Quantitative radical scavenging and metabolic enzyme inhibition activities of ZnO:Ag NR's at a concentration of 100 μg/mL were found to depend on the amount of Ag doped in up to a threshold level (3-4 %). Circular dichroism analysis revealed that the interaction of the NR's with the enzymes altered their secondary conformation. This alteration is the underlying mechanism for the potent enzyme inhibition.

CONCLUSIONS

Enhanced inhibition of enzymes and scavenging of free radicals primarily responsible for reactive oxygen species (ROS) mediated damage, provide a strong scientific rationale for considering ZnO:Ag NR's as a candidate nanomedicine for controlling postprandial hyperglycaemia and the associated oxidative stress.

Formation of nanoripples on ZnO flat substrates and nanorods by gas cluster ion bombardment

In the present study Ar⁺ cluster ions accelerated by voltages in the range of 5-10 kV are used to irradiate single crystal ZnO substrates and nanorods to fabricate self-assembled surface nanoripple arrays. The ripple formation is observed when the incidence angle of the cluster beam is in the range of 30-70°. The influence of incidence angle, accelerating voltage, and fluence on the ripple formation is studied. Wavelength and height of the nanoripples increase with increasing accelerating voltage and fluence for both targets. The nanoripples formed on the flat substrates remind of aeolian sand ripples. The ripples formed at high ion fluences on the nanorod facets resemble well-ordered parallel steps or ribs. The more ordered ripple formation on nanorods can be associated with the confinement of the nanorod facets in comparison with the quasi-infinite surface of the flat substrates.

Hybrid TiO2-ZnO Nanomaterials Prepared Using Laser Ablation in Liquid

Hybrids of semiconductor nanomaterials often demonstrate properties that are superior to those of their components. In this study, we prepared hybrid nanomaterials of TiO₂ and ZnO, which are among the most actively studied semiconductors, by means of millisecond-pulsed laser and analyzed how their morphology, particle size, and surface composition depend on preparation conditions. A series of nanomaterials were obtained via sequentially ablating Zn and Ti metal plates (in different sequences) in water, while laser pulses of lower (2.0 J/pulse) and higher (5.0 J/pulse) energy were applied. The properties of laser-produced hybrid TiO₂-ZnO nanomaterials were shown to be governed by experimental conditions such as laser pulse width, pulse peak power, and reaction media (either pure water or colloid with nanoparticles). The morphology revealed nanospheres of TiO₂ that decorate nanorods of ZnO or flower-like aggregates of zinc oxide. Intriguingly, after extended ablation time, titania was found to be self-doped with Ti³⁺ and Ti²⁺ ions, and the contribution of lower oxidation states of titanium could be controlled by the applied laser pulse energy. The physicochemical characteristics of hybrid nanomaterials were compared with pure ZnO and TiO₂ prepared under the same laser conditions.

Synergistic effect of zinc oxide nanorods on the photocatalytic performance and the biological activity of graphene nano sheets

In this work, decoration of the graphene surface with 5 wt. % ZnO nanorods (ZnO NRs), to ensure the potential photocatalytic performance of the formed nanocomposites, is demonstrated. Graphene oxide (GO) was synthesized with Hummer method followed by reduction to give reduced graphene oxide (RGO). The adjustable nano-compositing exhibited long-sought workability not only in in-situ incorporation of nanorods while reduction of graphene oxide (IZG) but also in ex-situ mixing of RGO or GO with the nanorods, (EZG) and (ZGO) respectively. The demineralization of synthetic wastewater has been evaluated by chemical oxygen demand and the obtained nanocomposites possess enhanced photocatalytic activities with 30 % and 35% over pure RGO and GO, respectively. This higher efficiency could be attributed to the synergistic effect between ZnO and the planner structure of graphene sheets which developed unprecedented polycrystalline structure. Also, the results proved that even the RGO or GO have played a dual function in photocatalysis, adsorption, and degradation. Also, the bactericidal effect of the prepared samples was studied against deleterious microorganisms. The findings of this work pave the way for the new generation of highly efficient photocatalysts based graphene with economic attraction and environmental impact.

Layered Double Hydroxide onto Perovskite Oxide-Decorated ZnO Nanorods for Modulation of Carrier Transfer Behavior in Photoelectrochemical Water Oxidation

Despite the fact that perovskite oxides with high photoelectrochemical (PEC) stability have gained widespread concern in the field of photo(electro)catalytic water splitting, the potential as a photoelectrode has not yet fully exploited. Herein, perovskite oxide-decorated ZnO nanorod photoanode improves the vital issue that photoproduced electron-hole pairs are apt to be quenched, in which type II band alignment between perovskite oxide and ZnO plays a crucial role in extracting carriers. Further, coupling with layered double hydroxide (LDH) onto the heterostructure not only tunes surface injection behavior of charge carriers by facilitating the interface reaction dynamics but also suppresses ZnO self-corrosion for extended durability. As a result, the optimized CoAl-LDH/LaFeO₃/ZnO nanorod photoanode yields a much enhancive effect for the PEC property in terms of photocurrent density (2.46 mA cm^-2 at 1.23 V vs reversible hydrogen electrode under AM 1.5G), onset potential, and stability. This work signifies a feasible design to combine promising perovskite oxides with the traditional photoelectrode system for achieving efficient water splitting.

Intrinsic Control in Defects Density for Improved ZnO Nanorod-Based UV Sensor Performance

Hitherto, most research has primarily focused on improving the UV sensor efficiency via surface treatments and by stimulating the ZnO nanorod (ZNR) surface Schottky barriers. However, to the best of our knowledge, no study has yet probed the intrinsic crystal defect generation and its effects on UV sensor efficiency. In this study, we undertake this task by fabricating an intrinsic defect-prone hydrothermally grown ZNRs (S1), Ga-doped ZNRs (S2), and defect-free microwave-assisted grown ZNRs (S3). The defect states were recognized by studying X-ray diffraction and photoluminescence characteristics. The large number of crystal defects in S1 and S2 had two pronged disadvantages. (1) Most of the UV light was absorbed by the defect traps and the e-h pair generation was compromised. (2) Mobility was directly affected by the carrier-carrier scattering and phonon scattering processes. Hence, the overall UV sensor efficiency was compromised based on the defect-induced mobility-response model. Considering the facts, defect-free S3 exhibited the best UV sensor performance with the highest on/off ratio, the least impulse response time, the highest recombination time, and highest gain-induced responsivity to 368 nm UV light, which was desired of an efficient passive metal oxide-based UV sensor. Our results were compared with the recently published results.

Efficient Metal Halide Perovskite Solar Cells Prepared by Reproducible Electrospray Coating on Vertically Aligned TiO2 Nanorod Electrodes

Vertically aligned TiO₂ nanorod (NR) electrodes with straight macropores enabled a metal halide perovskite (MHP) solution to be fully infiltrated within their structure and, as a result, formed void-free dense MHP films reproducibly during an electrospray-coating process, whereas conventional mesoporous TiO₂ (m-TiO₂) electrodes with three-dimensionally interconnected mesopores formed internal voids by imperfect infiltration of MHP solution. Hence, TiO₂ NR-based MHP solar cells could be more reproducibly fabricated by an electrospray-coating process and exhibited smaller current density-voltage hysteresis with respect to the scan direction and scan rate than the m-TiO₂-based MHP solar cells due to the short and straight electron pathway either by a one-dimensional TiO₂ NR electrode or a densely formed MHP layer within the TiO₂ NR electrode.

Room-temperature gas sensors based on ZnO nanorod/Au hybrids: Visible-light-modulated dual selectivity to NO2 and NH3

Gas sensors play vital roles in air pollution monitoring. Despite considerable progress in improving the room-temperature gas sensing sensitivities and rates of materials, comparably less attention is paid to the sensor selectivity. Here, ultrathin ZnO nanorods (˜15 nm) were synthesized by a nanoseed-assisted wet chemical approach and subsequently functionalized by Au nanoparticles by a photoreduction method. The hybrid material exhibited visible-light-activity owing to the surface plasmon resonance (SPR) effects of Au nanoparticles. The ZnO/Au hybrids were assembled into a high-performance, optically-controlled gas sensor operating at room temperature, which was found to be more selective to NH₃ in dark but showed high selectivity to NO₂ under visible-light illumination (λ = 532 nm). Moreover, the sensors exhibited high response and short response and recovery times as well as excellent reversibility and selectivity at room temperature. Such visible-light-modulated dual gas selectivity could be mainly attributed to the opposite direction of electron transfer between ZnO and Au nanoparticles in dark and under visible-light illumination, which led to the different surface depletion characteristics of the ZnO nanorods. In addition, the ultrathin diameters of nanorods also synergistically contributed to the light-controlled dual gas selectivity. The presently developed light modulation strategy provides an alternative approach to highly-selective and dual-functional gas sensors operating at room temperature.

Nanopiezoelectric Devices for Energy Generation Based on ZnO Nanorods/Flexible-Conjugated Copolymer Hybrids Using All Wet-Coating Processes

In this study, nanopiezoelectric devices based on ZnO nanorod array/conducting polymers are fabricated for wearable power generation application. To replace the inorganic rigid indium-tin oxide (ITO) conducting coating commonly used in the nanogenerator devices, a series of flexible polyaniline-based conducting copolymers underlying the perpendicularly-oriented ZnO nanorod arrays has been synthesized with improved electric conductivity by the copolymerization of aniline and 3,4-ethylenedioxythiophene (EDOT) monomers in order to optimize the piezoelectric current collection efficiency of the devices. It is found that significantly higher conductivity can be obtained by small addition of EDOT monomer into aniline monomer solution using an in-situ oxidative polymerization method for the synthesis of the copolymer coatings. The highest conductivity of aniline-rich copolymer is 65 S/cm, which is 2.5 times higher than that for homopolymer polyaniline coating. Subsequently, perpendicularly-oriented ZnO nanorod arrays are fabricated on the polyaniline-based copolymer substrates via a ZnO nanoparticle seeded hydrothermal fabrication process. The surface morphology, crystallinity, orientation, and crystal size of the synthesized ZnO nanorod arrays are fully examined with various synthesis parameters for copolymer coatings with different monomer compositions. It is found that piezoelectric current generated from the devices is at least five times better for the device with improved electric conductivity of the copolymer and the dense formation of ZnO nanorod arrays on the coating. Therefore, these results demonstrate the advantage of using flexible π-conjugated copolymer films with enhanced conductivity to further improve piezoelectric performance for future wearable energy harvesting application based on all wet chemical coating processes.

ZnO@TiO2 Core Shell Nanorod Arrays with Tailored Structural, Electrical, and Optical Properties for Photovoltaic Application

ZnO has prominent electron transport and optical properties, beneficial for photovoltaic application, but its surface is prone to the formation of defects. To overcome this problem, we deposited nanostructured TiO₂ thin film on ZnO nanorods to form a stable shell. ZnO nanorods synthesized by wet-chemistry are single crystals. Three different procedures for deposition of TiO₂ were applied. The influence of preparation methods and parameters on the structure, morphology, electrical and optical properties were studied. Nanostructured TiO₂ shells show different morphologies dependent on deposition methods: (1) separated nanoparticles (by pulsed laser deposition (PLD) in Ar), (2) a layer with nonhomogeneous thickness (by PLD in vacuum or DC reactive magnetron sputtering), and (3) a homogenous thin layer along the nanorods (by chemical deposition). Based on the structural study, we chose the preparation parameters to obtain an anatase structure of the TiO₂ shell. Impedance spectroscopy shows pure electron conductivity that was considerably better in all the ZnO@TiO₂ than in bare ZnO nanorods or TiO₂ layers. The best conductivity among the studied samples and the lowest activation energy was observed for the sample with a chemically deposited TiO₂ shell. Higher transparency in the visible part of spectrum was achieved for the sample with a homogenous TiO₂ layer along the nanorods, then in the samples with a layer of varying thickness.

Ultra-Violet Electroluminescence of ZnO Nanorods/MEH-PPV Heterojunctions by Optimizing Their Thickness and Using AZO as a Transparent Conductive Electrode

In this paper, a series of ITO/ZnO/ZnO nanorods/MEH-PPV/Al were prepared with different thicknesses of MEH-PPV that were changed from 15, 10 to 7 nm. The electric field in the devices was analyzed. An increase in the electric field on ZnO made hole injection easy and the electrons tunnel fast through thinner MEH-PPV to ZnO. This made the carriers prefer to recombine inside the ZnO layer, and the emission of ZnO was predominant under direct current (DC) bias. Furthermore, another device was fabricated with the structure of AZO (Al-doped ZnO)/ZnO/ZnO nanorods/MEH-PPV/Al. Ultra-violet (UV) electroluminescence (EL) at 387 nm from ZnO band edge emission was realized under DC bias. The turn-on voltage of the devices having AZO as the electrode is lower than that of ITO, and the EL power is enhanced. This work also studies the effect of inserting LiF underneath the Al electrode and above the layer of MEH-PPV. The LiF film inserted caused an obvious decrease in turn-on voltage of the devices and a pronounced increase in the EL power. The mechanism of electroluminescence enhancement is also discussed.

High-Performance Flexible Ultraviolet Photodetectors with Ni/Cu-Codoped ZnO Nanorods Grown on PET Substrates

As a developing technology for flexible electronic device fabrication, ultra-violet (UV) photodetectors (PDs) based on a ZnO nanostructure are an effective approach for large-area integration of sensors on nonconventional substrates, such as plastic or paper. However, photoconductive ZnO nanorods grown on flexible substrates have slow responses or recovery as well as low spectral responsivity R because of the native defects and inferior crystallinity of hydrothermally grown ZnO nanorods at low temperatures. In this study, ZnO nanorod crystallites are doped with Cu or Ni/Cu when grown on polyethylene terephthalate (PET) substrates in an attempt to improve the performance of flexible PDs. The doping with Ni/Cu or Cu not only improves the crystalline quality but also significantly suppresses the density of deep-level emission defects in as-grown ZnO nanorods, as demonstrated by X-ray diffraction and photoluminescence. Furthermore, the X-ray photoelectron spectroscopy analysis shows that doping with the transition metals significantly increases the oxygen bonding with metal ions with enhanced O/Zn stoichiometry in as-grown nanorods. The fabricated flexible PD devices based on an interdigitated electrode structure demonstrates a very high R of ~123 A/W, a high on-off current ratio of ~130, and a significant improvement in transient response speed exhibiting rise and fall time of ~8 and ~3 s, respectively, by using the ZnO nanorods codoped by Ni/Cu.

Orange/Red Photoluminescence Enhancement Upon SF6 Plasma Treatment of Vertically Aligned ZnO Nanorods

Although the origin and possible mechanisms for green and yellow emission from different zinc oxide (ZnO) forms have been extensively investigated, the same for red/orange PL emission from ZnO nanorods (nR) remains largely unaddressed. In this work, vertically aligned zinc oxide nanorods arrays (ZnO nR) were produced using hydrothermal process followed by plasma treatment in argon/sulfur hexafluoride (Ar/SF₆) gas mixture for different time. The annealed samples were highly crystalline with ~45 nm crystallite size, (002) preferred orientation, and a relatively low strain value of 1.45 × 10⁻³, as determined from X-ray diffraction pattern. As compared to as-deposited ZnO nR, the plasma treatment under certain conditions demonstrated enhancement in the room temperature photoluminescence (PL) emission intensity, in the visible orange/red spectral regime, by a factor of 2. The PL intensity enhancement induced by SF₆ plasma treatment may be attributed to surface chemistry modification as confirmed by X-ray photoelectron spectroscopy (XPS) studies. Several factors including presence of hydroxyl group on the ZnO surface, increased oxygen level in the ZnO lattice (O_L), generation of F–OH and F–Zn bonds and passivation of surface states and bulk defects are considered to be active towards red/orange emission in the PL spectrum. The PL spectra were deconvoluted into component Gaussian sub-peaks representing transitions from conduction-band minimum (CBM) to oxygen interstitials (O_i) and CBM to oxygen vacancies (V_O) with corresponding photon energies of 2.21 and 1.90 eV, respectively. The optimum plasma treatment route for ZnO nanostructures with resulting enhancement in the PL emission offers strong potential for photonic applications such as visible wavelength phosphors.

Optimization of ZnO Nanorod-Based Surface Enhanced Raman Scattering Substrates for Bio-Applications

Nanorods based on ZnO for surface enhanced Raman spectroscopy are promising for the non-invasive and rapid detection of biomarkers and diagnosis of disease. However, optimization of nanorod and coating parameters is essential to their practical application. With the goal of establishing a baseline for early detection in biological applications, gold-coated ZnO nanorods were grown and coated to form porous structures. Prior to gold deposition, the grown nanorods were 30–50 nm in diameter and 500–600 nm in length. Gold coatings were grown on the nanorod structure to a series of thicknesses between 100 and 300 nm. A gold coating of 200 nm was found to optimize the Rhodamine B model analyte signal, while performance for rat urine depended on the biomarkers to be detected. These results establish design guidelines for future use of Au-ZnO nanorods in the study and early diagnosis of inflammatory diseases.

High-Performance Ultraviolet Light Detection Using Nano-Scale-Fin Isolation AlGaN/GaN Heterostructures with ZnO Nanorods

Owing to their intrinsic wide bandgap properties ZnO and GaN materials are widely used for fabricating passive-type visible-blind ultraviolet (UV) photodetectors (PDs). However, most of these PDs have a very low spectral responsivity R, which is not sufficient for detecting very low-level UV signals. We demonstrate an active type UV PD with a ZnO nanorod (NR) structure for the floating gate of AlGaN/GaN high electron mobility transistor (HEMT), where the AlGaN/GaN epitaxial layers are isolated by the nano-scale fins (NFIs) of two different fin widths (70 and 80 nm). In the dark condition, oxygen adsorbed at the surface of the ZnO NRs generates negative gate potential. Upon UV light illumination, the negative charge on the ZnO NRs is reduced due to desorption of oxygen, and this reversible process controls the source-drain carrier transport property of HEMT based PDs. The NFI PDs of a 70 nm fin width show the highest R of a ~3.2 × 10⁷ A/W at 340 nm wavelength among the solid-state UV PDs reported to date. We also compare the performances of NFI PDs with those of conventional mesa isolation (MI, 40 × 100 µm²). NFI devices show ~100 times enhanced R and on-off current ratio than those of MI devices. Due to the volume effect of the small active region, a much faster response speed (rise-up and fall-off times of 0.21 and 1.05 s) is also obtained from the NFI PDs with a 70 nm fin width upon the UV on-off transient.

Fabriction of ZnO Nanorods with Strong UV Absorption and Different Hydrophobicity on Foamed Nickel under Different Hydrothermal Conditions

ZnO nanorods have been grown on the surface of foamed nickel by a two-step method. Firstly, a layer of ZnO seed is sputtered on the surface of the foamed nickel by magnetron sputtering, and then the hydrothermal method is used to grow ZnO nanorods at different conditions (solution concentration, reaction time and reaction temperature). The results show that the morphology of ZnO nanorods is closely related to the solution concentration, reaction time, and reaction temperature. The energy band structure formed by the foamed nickel and ZnO seed layers and the growth mechanism of ZnO nanorods are discussed. The samples are characterized by Energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Raman spectroscopy. The absorption characteristics of samples to light are characterized by ultraviolet-to-visible (UV–VIS) absorption. The hydrophilicity of the samples is characterized by the static contact angle. By analyzing the performance characteristics of the samples at different conditions, we finally obtained the optimal growth parameters. At the optimal parameters, the morphology of the grown nanorods is regular, the ultraviolet band has strong absorption, and the surface of the samples forms a superhydrophobic surface.

Diagnosis in a Preclinical Model of Bladder Pain Syndrome Using a Au/ZnO Nanorod-based SERS Substrate

To evaluate the feasibility of ZnO nanorod-based surface enhanced Raman scattering (SERS) diagnostics for disease models, particularly for interstitial cystitis/bladder pain syndrome (IC/BPS), ZnO-based SERS sensing chips were developed and applied to an animal disease model. ZnO nanorods were grown to form nano-sized porous structures and coated with gold to facilitate size-selective biomarker detection. Raman spectra were acquired on a surface enhanced Raman substrate from the urine in a rat model of IC/BPS and analyzed using a statistical analysis method called principal component analysis (PCA). The nanorods grown after the ZnO seed deposition were 30 to 50 nm in diameter and 500 to 600 nm in length. A volume of gold corresponding to a thin film thickness of 100 nm was deposited on the grown nanorod structure. Raman spectroscopic signals were measured in the scattered region for nanometer biomarker detection to indicate IC/BPS. The Raman peaks for the control group and IC/BPS group are observed at 641, 683, 723, 873, 1002, 1030, and 1355 cm⁻¹, which corresponded to various bonding types and compounds. The PCA results are plotted in 2D and 3D. The Raman signals and statistical analyses obtained from the nano-sized biomarkers of intractable inflammatory diseases demonstrate the possibility of an early diagnosis.

In-Situ Fabrication of g-C₃N₄/ZnO Nanocomposites for Photocatalytic Degradation of Methylene Blue: Synthesis Procedure Does Matter

The nanocomposite preparation procedure plays an important role in achieving a well-established heterostructured junction, and hence, an optimized photocatalytic activity. In this study, a series of g-C₃N₄/ZnO nanocomposites were prepared through two distinct procedures of a low-cost, environmentally-friendly, in-situ fabrication process, with urea and zinc acetate being the only precursor materials. The physicochemical properties of synthesized g-C₃N₄/ZnO composites were mainly characterized by XRD, UV–VIS diffuse reflectance spectroscopy (DRS), N₂ adsorption-desorption, FTIR, TEM, and SEM. These nanocomposites’ photocatalytic properties were evaluated in methylene blue (MB) dye photodecomposition under UV and sunlight irradiation. Interestingly, compared with ZnO nanorods, g-C₃N₄/ZnO nanocomposites (x:1, obtained from urea and ZnO nanorods) exhibited weak photocatalytic activity likely due to a “shading effect”, while nanocomposites (x:1 CN, made from g-C₃N₄ and zinc acetate) showed enhanced photocatalytic activity that can be ascribed to the effective establishment of heterojunctions. A kinetics study showed that a maximum reaction rate constant of 0.1862 min^-1 can be achieved under solar light illumination, which is two times higher than that of bare ZnO nanorods. The photocatalytic mechanism was revealed by determining reactive species through adding a series of scavengers. It suggested that reactive ●O₂⁻ and h⁺ radicals played a major role in promoting dye photodegradation.

Plasmonic-Enhanced Luminescence Characteristics of Microscale Phosphor Layers on a ZnO Nanorod-Arrayed Glass Substrate

We present a planar luminescent layer for glare-free, long-lifespan white light-emitting diodes (LEDs), with attractive light outputs. The novel and facile remote phosphor approach proposed in this work enhances luminescence properties by combining a waveguiding ZnO-based nanostructure with plasmonic Au nanoparticles. The system comprised a microscale yellow phosphor layer that is applied by simple printing onto an Au nanoparticle-dispersed ZnO nanorod array. This architecture resulted in a considerable enhancement in luminous efficacy of approximately 18% because of the combination of waveguide effects from the nanorod structure and plasmonic effects from the Au nanoparticles. Performance was optimized according to the length of the Zn nanorods and the concentration of Au. An optimal efficiency of ∼84.26 lm/W for a silicate phosphor-converted LED was achieved using long ZnO nanorods and an Au concentration of 12.5 ppm. The finite-difference time-domain method was successfully used to verify the luminous efficacy improvements in the Au nanoparticle-intervened nanostructures via the waveguiding and plasmonic effects.

The sonochemical synthesis of vertically aligned ZnO nanorods and their UV photodetection properties: Effect of ZnO buffer layer

Vertically aligned Zinc oxide nanorods (ZnO NRs) were successfully synthesized in this study using the sonochemical method to improve the intrinsic properties of UV photodetector (PD). Three different thin films: Ti/Zn, Ti/ZnO, and Ti/ZnO/Zn, with the thicknesses of 10 nm/55 nm, 10 nm/85 nm, and 10 nm/85 nm/55 nm respectively, were deposited on glass substrates using the RF-sputtering technique. The synthesized ZnO NRs were investigated using XRD, FESEM and Raman spectroscopy to determine the effect of Zn and ZnO as seed layers, and ZnO as a buffer layer on the surface morphology, crystal structure, optical properties of ZnO NRs. The ZnO NRs grown on Zn/Ti, ZnO/Ti, and Zn/ZnO/Ti are characterized by hexagonal crystal structure with preferential growth in the c-axis direction. The ZnO NRs grown on Zn/ZnO/Ti displayed the highest density, uniform size distribution, vertically aligned rods and aspect ratio. The UV device fabricated from the ZnO NRs grown on Zn /ZnO/Ti also showed the highest photocurrent (360 µA) and responsivity of (878 mA/W). ZnO NRs grown on Zn/ZnO/Ti were also observed to be highly stable and exhibited a relatively rapid response and recovery times for different time intervals when exposed to the UV light of 365 nm wavelength. Thus, the inclusion of the ZnO as a buffer layer (Zn as a seed layer/ZnO as buffer layer/Ti as a buffer layer) improve the properties of the ZnO NRs. In addition, the current gain of ZnO NRs grown on Zn (55 nm)/ZnO (85 nm)/Ti (10 nm) - based ultraviolet (UV) photodetector (PD) is about two times higher than that of conventional Zn (55 nm)/ZnO (85 nm)/Ti (10 nm) thin-films UV PD, which is due to the higher surface-to-volume ratio of ZnO nanorods (NRs) compared with their thin films. This study confirms the possibility of sonochemically fabricating vertically aligned ZnO nanorods as well as its applicability as a viable UV photodetector.

Enhancement of local surface plasmon resonance (LSPR) effect by biocompatible metal clustering based on ZnO nanorods in Raman measurements

The development of size-selective and non-destructive detection techniques for nanosized biomarkers has many reasons, including the study of living cells and diagnostic applications. We present an approach for Raman signal enhancement on biocompatible sensing chips based on surface enhancement Raman spectroscopy (SERS). A sensing chip was fabricated by forming a ZnO-based nanorod structure so that the Raman enhancement occurred at a gap of several tens to several hundred nanometers. The effect of coffee-ring formation was eliminated by introducing the porous ZnO nanorods for the bio-liquid sample. A peculiarity of this approach is that the gold sputtered on the ZnO nanorods initially grows at their heads forming clusters, as confirmed by secondary electron microscopy. This clustering was verified by finite element analysis to be the main factor for enhancement of local surface plasmon resonance (LSPR). This clustering property and the ability to adjust the size of the nanorods enabled the signal acquisition points to be refined using confocal based Raman spectroscopy, which could be applied directly to the sensor chip based on the optimization process in this experiment. It was demonstrated by using common cancer cell lines that cell growth was high on these gold-clad ZnO nanorod-based surface-enhanced Raman substrates. The porosity of the sensing chip, the improved structure for signal enhancement, and the cell assay make these gold-coated ZnO nanorods substrates promising biosensing chips with excellent potential for detecting nanometric biomarkers secreted by cells.