A new method for CE-EC determination of mercaptopurine (MP) in a PMMA biochip with on-chip gold nano-electrode ensemble (GNEE) working and decouple electrodes

This paper presents a new method for CE-EC determination of Mercaptopurine (MP), one of the most important medicines for inflammatory bowel disease (IBD) and acute lymphoblastic leukemia (ALL) treatment, in a PMMA-based microfluidic chip. A simple and reliable process for preparing the template of gold nanoelectrode ensemble (GNEE) and fabricating the integrated microfluidic chip is reported in the present study. The use of GNEE electrodes for both electric current decoupling and signal sensing in the proposed CE-EC chip not only enhances the signal response but also decreases the background noise during detection. Results show that a good detection limit of 100 nM for detecting mercaptopurine is achieved with the proposed method. In addition, the measured results also shows a good linear response between the detected CE-EC signals and the concentration of MP within the range of 100 nM-10 mM (R2 = 0.989). The proposed microchip device provides a novel and fast detection method for mercaptopurine analysis.

Role of three-dimensional power Doppler in the antenatal diagnosis of placenta accreta: comparison with gray-scale and color Doppler techniques

OBJECTIVE

To assess the role of three-dimensional (3D) power Doppler in the antenatal diagnosis of placenta accreta and compare its diagnostic performance with gray-scale and color Doppler ultrasonography.

METHODS

One hundred and seventy pregnant women with persistent placenta previa totalis (after 28 weeks' gestation) were prospectively enrolled into this study. Gray-scale transabdominal ultrasound examination was performed to detect loss of the subendometrial echolucent zone and other abnormalities suggestive of placenta accreta. Color flow mapping was used to scan the whole placenta to detect any newly formed vessels at the serosa-bladder border or the presence of abnormal lacunae. Finally a targeted examination of angioarchitecture in the basal and lateral views of the placenta was carried out using 3D power Doppler. The ultrasound findings were analyzed with reference to the final diagnosis made during Cesarean delivery.

RESULTS

Placenta accreta and its variants (including increta and percreta) were confirmed in 39 patients at the time of Cesarean delivery. Based on receiver-operating characteristics analysis, 'numerous coherent vessels' visualized using 3D power Doppler in the basal view was the best single criterion for the diagnosis of placenta accreta, with a sensitivity of 97% and a specificity of 92%. If we considered the presence of at least one criterion to be diagnostic when using each ultrasound technique, then 3D power Doppler would have the best positive predictive value (76%), followed by gray-scale (51%) and color Doppler (47%). The majority of patients with placenta accreta showed multiple characteristic features on ultrasound imaging. In contrast, those patients with a false-positive diagnosis (i.e. the final diagnosis was placenta previa alone) tended to show isolated ultrasound markers of the condition.

CONCLUSION

3D power Doppler may be useful as a complementary technique for the antenatal diagnosis or exclusion of placenta accreta.

Nanomachining with a mechanical manipulation system

This study describes about the development of a mechanical manipulation system that can perform three-dimensional nano-machining inside a scanning electron microscope (SEM). Experiments are carried out by constructing a precise machining platform integrated with pico-motors, linear stages and monolithic-silicon-based tips which is generally used in atomic-force microscope (AFM). This integrated system can easily manipulate the atoms in a workpiece inside an SEM. The platform consists of three translational stages along XYZ axis direction and one rotational stage, with a resolution of 30 nm. The system can be utilized to produce nanopattern such as nanolines, nanoscale characters on silicon substrate coated with gold (Au) and aluminum (Al). Molecular dynamics simulation model is used to analyze the machining mechanism from various machining parameters. The same AFM tip can be utilized to scratch away the unwanted material from the workpiece surface.

'Big-eyed frog' sign on spatiotemporal image correlation (STIC) in the antenatal diagnosis of transposition of the great arteries

OBJECTIVE

To determine the value of simultaneous visualization of the cross-sectional view of both atrioventricular (AV) valves, the pulmonary artery and the aorta (en-face view of the AV valves and great vessels) in the identification of fetuses with transposition of the great arteries (TGA).

METHODS

This was a retrospective analysis of volume datasets obtained with the spatiotemporal image correlation (STIC) technique from 56 fetuses with and 30 fetuses without congenital heart defects. Volume datasets were reviewed offline to compare the en-face view of the AV valves and great vessels between fetuses with normal echocardiography and those with TGA.

RESULTS

The en-face view of both AV valves and great vessels in fetuses with TGA displayed the main pulmonary artery situated side-by-side with the aorta ('big-eyed frog' sign). In contrast, fetuses with normal hearts did not have this characteristic sonographic sign. This novel sonographic sign also helped to identify additional cases of TGA in 17 fetuses with complex heart defects.

CONCLUSION

The big-eyed frog sign may prove helpful in the prenatal diagnosis of TGA.

Using direct nanoimprinting of ferroelectric films to prepare devices exhibiting bi-directionally tunable surface plasmon resonances

In this paper, we describe an imprint method for the fabrication of bi-directionally tunable surface plasmon resonance (SPR) filters. A periodic metal/ferroelectric film stack exhibiting SPR phenomena was directly imprinted using a sharp mold without the need for a polymer-based resist. Both the refractive index of the surrounding lead zirconate titanate (PZT) films and the period of the textured PZT/metal/PZT structure were dependent upon both the absolute value and sign of the applied potential. The SPR wavelength of the PZT/gold/PZT-based tunable filter varied over a range of greater than 100 nm when applying potentials ranging from 0 to -15 V. This imprinting method has great potential for use in the fabrication of tunable optical filters without the need for complicated processes or specific materials.

Monolithically integrated multi-wavelength filter and second harmonic generator in aperiodically poled lithium niobate

We report on the design and experimental characterization of aperiodically poled lithium niobate (APLN) crystals for use in monolithically integrated dual nonlinear-optical devices. A cascade and a single aperiodic-domain-structure designs based on simulated annealing method were constructed in LiNbO(3) to simultaneously perform as 4-channel electro-optically active (EOA) filters and 4-channel frequency doublers in the telecom band. We found that we could obtain a 2.44-fold enhancement in second-harmonic-generation conversion efficiency and a 2.4-time reduction in filter transmission bandwidth with the single APLN device over the cascade one when the same device length of 2 cm and the EOA field of 1027 V/mm were used.

Genome-wide copy number analysis using copy number inferring tool (CNIT) and DNA pooling

Copy number variation (CNV) has become an important genomic structure element in the human population, and some CNVs are related to specific traits and diseases. Moreover, analysis of human genomes has been potentiated by the use of high-resolution microarrays that assess single nucleotide polymorphisms (SNPs). Although many programs have been designed to analyze data from Affymetrix SNP microarrays, they all have high false-positive rates (FPRs) in copy number (CN) analyses. Copy number analysis tool (CNAT) 4.0 is a recently developed program that offers improved CN estimation, but small amplifications and deletions are lost when using the smoothing procedure. Here, we propose a copy number inferring tool (CNIT) algorithm for the 100K SNP microarray to investigate CNVs at 29.6-kb resolution. CNIT estimated SNP allelic and total CN with reliable P values based on intensity data. In addition, the hidden Markov model (HMM) method was applied to predict regions having altered CN by considering contiguous SNPs. Based on a CN analysis of 23 unrelated Taiwanese and 30 HapMap Centre d'Etude du Polymorphisme Humain (CEPH) trios, CNIT showed higher accuracy and power than other programs. The FPRs and false-negative rates (FNRs) of CNIT were 0.1% and 0.16%, respectively. CNIT also showed better sensitivity for detecting small amplifications and deletions. Furthermore, DNA pooling of 10 and 30 normal unrelated individuals were applied to the 100K SNP microarray, respectively, and 12 common CN-variable regions were identified, suggesting that DNA pooling can be applied to discover common CNVs.

First Report of Fruit Rot of Strawberry Caused by an Alternaria sp. in Taiwan

In March 2005, a fruit rot disease was found in several commercial strawberry (Fragaria × ananassa Duchesne) fields at Fongyuan, 24.25°N, 120.72°E, in Taichung County in central Taiwan. The disease was rare and was negligible in most cultivated areas. However, disease incidence has increased by 4 to 5% over the last 2 years and causes significant postharvest losses. In storage, symptoms on berries include light brown-to-black, sunken, irregularly shaped lesions. The lesions gradually enlarge and become firm with a dark green-to-black, velvety surface composed of mycelia, conidiophores, and conidia. Twelve single conidial isolates (AF-1 to AF-12) of a fungus were isolated by placing portions of symptomatic fruit from four locations onto acidified potato dextrose agar (PDA) and incubating at 24 ± 1°C. One isolate from each of the four locations, AF-2, 6, 9, and 12, was selected for identification and pathogenicity studies. The fungus was identified as an Alternaria sp. according to the morphological descriptions of A. tenuissima (2,3). Conidiophores were simple or branched, straight or flexuous, septate, pale to light brown, 3.0 to 5.0 μm in diameter, and bore two to six conidia in a chain. Conidia were dark brown, obclavate or oval, and multicellular with seven transverse (in most cases) and numerous longitudinal septa. Conidia were 15.5 to 56.5 μm (average 35.0 μm) long × 6.0 to 15.0 μm (average 11.0 μm) wide at the broadest point. The pathogen was consistently isolated from berries in the field or in storage. Pathogenicity tests were conducted by inoculating 12 surface-sterilized berries with each of the four isolates. Approximately 300 μl of a spore suspension (2 × 10⁵ conidia per ml) was placed at two points on the uninjured surface of each fruit and allowed to dry for 5 min. Control fruits were treated with sterile water. The berries were then enclosed in a plastic bag and incubated at 24 ± 1°C for 2 days. Disease symptoms similar to those described above were observed on 95% of inoculated berries 3 days after inoculation, while no symptoms developed in control berries. Reisolation from the inoculated berries consistently yielded the Alternaria sp. described above. Pathogenicity tests were performed three times. Previously, strawberry fruit rot caused by A. tenuissima was reported from Florida (2) and Malaysia (1), however, to our knowledge, this is the first report of fruit rot of strawberry caused by a species of Alternaria in Taiwan. References: (1) W. D. Cho et al. List of Plant Diseases in Korea. Korean Society of Plant Pathology, 2004. (2) C. M. Howard and E. E. Albregts. Phytopathology 63:938, 1973. (3) R. D. Milholland. Phytopathology 63:1395, 1973.

Sodium trimer ordering on a NaxCoO2 surface

Sodium ion ordering on an in situ cleaved NaxCoO2 (x=0.84) surface has been studied by ultrahigh vacuum scanning tunneling microscopy at room temperature. Three main phases, with p(3 x 3), ( radical7 x radical7), and (2 radical3 x 2 radical3) hexagonal unit cells and a surface Na concentration of 1/3, 3/7, 1/2, respectively, were identified. One surprising finding is that Na trimers act as the basic building blocks that order in long range. The stability of Na trimers is attributed to the increased Na coordination with oxygen as indicated by ab initio calculations, and possibly at finite temperature by configuration entropy.

Enhanced light output from a nitride-based power chip of green light-emitting diodes with nano-rough surface using nanoimprint lithography

Enhanced light extraction from a GaN-based power chip (PC) of green light-emitting diodes (LEDs) with a rough p-GaN surface using nanoimprint lithography is presented. At a driving current of 350 mA and with a chip size of 1 mm × 1 mm packaged on transistor outline (TO)-cans, the light output power of the green PC LEDs with nano-rough p-GaN surface is enhanced by 48% when compared with the same device without a rough p-GaN surface. In addition, by examining the radiation patterns, the green PC LED with nano-rough p-GaN surface shows stronger light extraction with a wider view angle. These results offer promising potential to enhance the light output powers of commercial light-emitting devices by using the technique of nanoimprint lithography under suitable nanopattern design.

First Report of Gummosis Disease of Plum (Prunus salicina) Caused by a Botryosphaeria sp. in Taiwan

Plum (Prunus salicina Lindell) is grown on more than 3,870 ha in Taiwan. In 2004, a gummosis disease was observed on plum in the Ming Jian Region of Nantou County (120.675°E, 23.919°N), with 15% of the trees affected. Infections started on the current year's growth, primarily through lenticels, and formed small, sunken, discolored lesions. At later stages, white gum exuded from the lesions. Circular to oval, brown, necrotic areas were seen on the inner bark. Severely infected twigs showed defoliation and dieback. During the winter months, numerous black pycnidia or perithecia formed on infected twigs. Single conidial isolates of the pathogen were obtained from diseased twigs on acidified potato dextrose agar (PDA) and incubated at 25 ± 1°C for 3 days. On the basis of morphological traits, the fungus was identified as a Botryosphaeria sp. according to the CMI descriptions of Botryosphaeria ribis (3). Conidia (14.2 to 26.8 × 4.3 to 7.2 μm) were single celled, hyaline, and spindle shaped. Asci (105 to 135 × 12.5 to 15.5 μm) were hyaline, clavate, and bitunicate. Ascospores (18 to 22 × 7.0 to 8.2 μm) were hyaline and spindle shaped or fusoid. For pathogenicity tests, inoculum was prepared by culturing the fungus on PDA under continuous fluorescent light (128 ± 25 μE·m^-2·s^-1) at 25°C for 3 days. Two twigs on each of six trees were inoculated. Sharp incisions (3 × 3 × 3 mm) were made on healthy twigs (12 to 15 months old) with a sterilized scalpel and inoculated with either a 5-mm mycelial disc or 0.5 ml of a conidial suspension (10⁵ conidia/ml) of the fungus. Inoculated areas were covered with moist, sterile cotton and the entire twigs were enclosed in plastic bags. Twigs inoculated with 5-mm PDA discs or sterile water alone served as controls. The symptoms described above were observed on all inoculated twigs 14 days after inoculation, whereas control twigs did not develop any disease symptoms. Reisolation from the inoculated twigs consistently yielded the Botryosphaeria sp., thus fulfilling Koch's postulates. Botryosphaeria spp. have been reported to cause stem blight of many plants in temperate and tropical regions of the world (4). In Taiwan, B. dothidea has been reported as the causal agent of gummosis disease of peach (1) and fruit ring rot of pear (2); however, to our knowledge, this is the first report of a Botryosphaeria sp. causing gummosis of plum. References: (1). Y. Ko et al. Plant Pathol. Bull. 1:70, 1992. (2) Y. Ko et al. Plant Prot. Bull. (Taiwan) 35:211, 1993. (3) E. Punithalingam and P. Holliday. No. 395 in: Descriptions of Pathogenic Fungi and Bacteria. CMI, Kew, Surrey, UK, 1973. (4) W. A. Sinclair et al. Diseases of Trees and Shrubs. Cornell University Press, Ithaca, NY, 1987.

A discrete-time multivariable neuro-adaptive control for nonlinear unknown dynamic systems

First, we assume that the controlled systems contain a nonlinear matrix gain before a linear discrete-time multivariable dynamic system. Then, a forward control based on a nominal system is employed to cancel the system nonlinear matrix gain and track the desired trajectory. A novel recurrent-neural-network (RNN) with a compensation of upper bound of its residue is applied to model the remained uncertainties in a compact subset /spl Omega/. The linearly parameterized connection weight for the function approximation error of the proposed network is also derived. An e-modification updating law with projection for weight matrix is employed to guarantee its boundedness and the stability of network without the requirement of persistent excitation. Then a discrete-time multivariable neuro-adaptive variable structure control is designed to improve the system performances. The semi-global (i.e., for a compact subset /spl Omega/) stability of the overall system is then verified by the Lyapunov stability theory. Finally, simulations are given to demonstrate the usefulness of the proposed controller.

Diode-pumped, actively internal-Q-switched Nd:MgO:PPLN laser

We demonstrated a laser-diode-pumped, electro-optically internal-Q-switched laser system radiating at 1.085 mum fabricated using a periodically poled Nd:MgO:LiNbO3 (Nd:MgO:PPLN) crystal. The Nd:MgO:PPLN is 17-mm long and has a 12-mm long, 13.6-mum period polarization-mode quasi-phase-matching (PM QPM) grating section functioning as the Q-switch of the laser system. When the Nd:MgO:PPLN Q-switch was driven by a 260-V voltage pulse train at 5 kHz, we obtained laser pulses of pulse energy >2.45 muJ and a pulse width of ~28 ns, corresponding to a laser peak power of ~88 W, from this internal-Q-switched laser system with 2% output coupling at an absorbed diode pump power of 0.61 W.

Anomalous surface diffusion of C60 and anisotropic growth of nano islands on Ni(111)

The migration behavior of C60 on Ni(111) has been inferred from its growth morphology at various substrate temperatures, as observed with scanning tunneling microscopy. The number density of islands increased and their average sizes decreased anomalously in the temperature range of approximately 573 K to approximately 973 K. This trend contradicts the prediction in conventional nucleation theory. At low and high temperatures, C60 commence nucleation on both sides of surface steps in a "bi-directional step flow" mode. However, anisotropy occurs within an intermediate temperature range, in which C60 nucleate predominantly at upper step edges. Surprisingly, in-situ growth measurements at this intermediate temperature range revealed that C60 actually start nucleating from lower step edges, with concomitant formation of Ni terraces underneath. These anomalous thermal dependence of diffusivity and the peculiar growth morphology of C60 on Ni(111) are attributed to C60-induced reconstruction of Ni(111) at higher temperature.

Mechanical properties of microwave hydrothermally synthesized titanate nanowires

In this investigation titanate nanowires were synthesized by a microwave hydrothermal process and their nanomechanical characterization was carried out by a compression experiment via buckling instability using a nanomanipulator inside a scanning electron microscope. Nanowires of diameters 120-150 nm and length tens of microns can be synthesized by keeping a commercial nanoparticle inside a microwave oven at 350 W and 210 °C for 5 h. The nanowire was clamped between two cantilevered AFM tips attached to two opposing stages of the manipulator for nanomechanical characterization. The elasticity coefficients of the titanate nanowires were measured by applying a continuously increasing load and observing the buckling instability of the nanowires. The buckling behavior of a nanowire was analyzed from the series of SEM images of displacement of the cantilever attached to the nanowire due to application of load. The critical loads for different sized titanate nanowires were determined and their corresponding Young's modulus was computed with the Euler pinned-fixed end model. The Young's modulus of these microwave hydrothermal process synthesized titanate nanowires were determined to be approximately in the range 14-17 GPa. This investigation confirms the capability of the nanomanipulator via the buckling technique as a constructive device for measuring the mechanical properties of nanoscale materials.

Bioremediation of atrazine-contaminated soil by forage grasses: transformation, uptake, and detoxification

A sound multi-species vegetation buffer design should incorporate the species that facilitate rapid degradation and sequestration of deposited herbicides in the buffer. A field lysimeter study with six different ground covers (bare ground, orchardgrass, tall fescue, timothy, smooth bromegrass, and switchgrass) was established to assess the bioremediation capacity of five forage species to enhance atrazine (ATR) dissipation in the environment via plant uptake and degradation and detoxification in the rhizosphere. Results suggested that the majority of the applied ATR remained in the soil and only a relatively small fraction of herbicide leached to leachates (<15%) or was taken up by plants (<4%). Biological degradation or chemical hydroxylation of soil ATR was enhanced by 20 to 45% in forage treatment compared with the control. Of the ATR residues remaining in soil, switchgrass degraded more than 80% to less toxic metabolites, with 47% of these residues converted to the less mobile hydroxylated metabolites 25 d after application. The strong correlation between the degradation of N-dealkylated ATR metabolites and the increased microbial biomass carbon in forage treatments suggested that enhanced biological degradation in the rhizosphere was facilitated by the forages. Hydroxylated ATR degradation products were the predominant ATR metabolites in the tissues of switchgrass and tall fescue. In contrast, the N-dealkylated metabolites were the major degradation products found in the other cool-season species. The difference in metabolite patterns between the warm- and cool-season species demonstrated their contrasting detoxification mechanisms, which also related to their tolerance to ATR exposure. Based on this study, switchgrass is recommended for use in riparian buffers designed to reduce ATR toxicity and mobility due to its high tolerance and strong degradation capacity.

First Report of Gray Leaf Spot of Mango (Mangifera indica) Caused by Pestalotiopsis mangiferae in Taiwan

Mango (Mangifera indica L.; family Anacardiaceae) is one of the world's most important fruit crops and is widely grown in tropical and subtropical regions. Since 2001, a leaf spot disease was found in mango orchards of Taiwan. Now, the disease was observed throughout (approximately 21,000 ha) Taiwan in moderate to severe form, thus affecting the general health of mango trees and orchards. Initial symptoms were small, yellow-to-brown spots on leaves. Later, the irregularly shaped spots, ranging from a few millimeters to a few centimeters in diameter, turned white to gray and coalesced to form larger gray patches. Lesions had slightly raised dark margins. On mature lesions, numerous black acervuli, measuring 290 to 328 μm in diameter, developed on the gray necrotic areas. Single conidial isolates of the fungus were identified morphologically as Pestalotiopsis mangiferae (Henn.) Steyaert (2,3) and were consistently isolated from the diseased mango leaves on acidified (0.06% lactic acid) potato dextrose agar (PDA) medium incubated at 25 ± 1°C. Initially, the fungus grew (3 mm per day) on PDA as a white, chalky colony that subsequently turned gray after 2 weeks. Acervuli developed in culture after continuous exposure to light for 9 to 12 days at 20 to 30°C. Abundant conidia oozed from the acervulus as a creamy mass. The conidia (17.6 to 25.4 μm long and 4.8 to 7.1 μm wide) were fusiform and usually straight to slightly curved with four septa. Three median cells were olivaceous and larger than the hyaline apical and basal cells. The apical cells bore three (rarely four) cylindrical appendages. Pathogenicity tests were conducted with either 3-day-old mycelial discs or conidial suspension (10⁵ conidia per ml) obtained from 8- to 10-day-old cultures. Four leaves on each of 10 trees were inoculated. Before inoculation, the leaves were washed with a mild detergent, rinsed with tap water, and then surface sterilized with 70% ethanol. Leaves were wounded with a needle and exposed to either a 5-mm mycelial disc or 0.2 ml of the spore suspension. The inoculated areas were wrapped with cotton pads saturated with sterile water and the leaves were covered with polyethylene bags for 3 days to maintain high relative humidity. Wounded leaves inoculated with PDA discs alone served as controls. The symptoms described above were observed on all inoculated leaves, whereas uninoculated leaves remained completely free from symptoms. Reisolation from the inoculated leaves consistently yielded P. mangiferae, thus fulfilling Koch's postulates. Gray leaf spot is a common disease of mangos in the tropics and is widely distributed in Africa and Asia (1-3); however, to our knowledge, this is the first report of gray leaf spot disease affecting mango in Taiwan. References: (1) T. K. Lim and K. C. Khoo. Diseases and Disorders of Mango in Malaysia. Tropical Press. Malaysia, 1985. (2) J. E. M. Mordue. No. 676 in: CMI Descriptions of Pathogenic Fungi and Bacteria. Surrey, England, 1980. (3) R. C. Ploetz et al. Compendium of Tropical Fruit Diseases. The American Phytopathological Society. St. Paul, MN, 1994.

Effect of ropivacaine on endothelium-dependent phenylephrine-induced contraction in guinea pig aorta

BACKGROUND

Previous studies have shown that ropivacaine has biphasic vascular effects, causing vasoconstriction at low concentrations and vasorelaxation at high concentrations. This study was designed to examine the role of the endothelium during accidental intravascular absorption of ropivacaine, and to elucidate the mechanisms responsible.

METHODS

Isolated guinea pig aortic rings were suspended for isometric tension recording. The effects of ropivacaine on endothelium-intact and endothelium-denuded aortic rings were assessed. Endothelium-intact aortic rings were pre-contracted with phenylephrine before being exposed to ropivacaine and acetylcholine, in order to generate and compare concentration-response curves. In the absence and presence of yohimbine, propranolol, atropine, indometacin, N(G)-nitro-l-arginine methyl ester (l-NAME), 1H-[1,2,4]oxadiazolo[4,3-a]quinoxalin-1-one (ODQ) or methylene blue, the contractile response induced by ropivacaine was assessed on endothelium-intact aortic rings pre-contracted with phenylephrine.

RESULTS

Ropivacaine (3 x 10(-4) to 10(-2) mol/l) produced vasoconstriction in endothelium-denuded aortic rings, whereas no such response was observed in aortic rings with intact endothelium. In phenylephrine pre-contracted intact aortic rings, ropivacaine induced a greater degree of vasorelaxation than did acetylcholine. Yohimbine, propranolol and atropine all failed to affect the relaxation responses induced by ropivacaine. However, pre-treatment with indometacin (cyclo-oxygenase inhibitor), l-NAME (nitric oxide synthase inhibitor), methylene blue (soluble guanylyl cyclase inhibitor) or ODQ (soluble guanylyl cyclase inhibitor), significantly decreased the ropivacaine-induced relaxation of endothelium-intact aortic rings (3 x 10(-4) to 10(-2) mol/l).

CONCLUSIONS

Ropivacaine elicits an endothelium-dependent vasorelaxation in phenylephrine pre-contracted aortic rings via the nitric oxide-cyclic guanosine 3',5'-monophosphate pathway and the prostaglandin system.

Using colloidal lithography to fabricate and optimize sub-wavelength pyramidal and honeycomb structures in solar cells

The external quantum efficiency of solar cells can be improved by using texturing pyramid- and honeycomb-like structures with minimum reflection. In this study, we investigated the reflection properties of texturing structures through rigorous coupled-wave analysis and the three-dimensional finite-difference time domains (FDTD) method to analyze close-packed texturing structures. We also demonstrate a simple method-combining sub-wavelength-scale monolayer and bilayer polystyrene spheres with a one-step reactive ion etching process-to fabricate optimized pyramid- and honeycomb-shaped antireflection structures, respectively. Thus, sub-wavelength pyramidal and honeycomb-like structures displaying low reflectance were obtained readily without the need for any lithography equipment.

First Report of Gray Mold Disease of Sponge Gourd (Luffa cylindrica) Caused by Botrytis cinerea in Taiwan

A disease of sponge gourd (Luffa cylindrica (L.) Roem., family Cucurbitaceae) has become a serious threat to sponge gourd production since 2003 in central Taiwan. Initially, symptoms appear as small, brown spots on the flower petals that spread to the entire flower and cause blossom blight within 2 to 3 days. Subsequently, the pathogen develops abundant mycelium and moves from the petals onto the fruits causing blossom end rot and fruit stem rot. Severely infected fruits become completely rotten and desiccate. Tissues were excised from diseased sponge gourd fruits (sampled from Fongyuan, located at 24.25°N, 120.72°E in Taichung County), immersed in a solution containing 3% sodium hypochlorite and 70% ethanol for 1 min, washed three times with sterile water, and then cultured on potato dextrose agar (PDA) medium. A fungus, identified as Botrytis cinerea, produced abundant mycelium on PDA medium when incubated under constant fluorescent light 185 ± 35 μE·m^-2·s^-1 at 24°C. The conidia were smooth, hyaline, and globoid or slightly ellipsoid. The conidia measured 9.5 to 19.3 μm (average 13.8 μm) long and 6.0 to 17.8 μm (average 10.1 μm) wide, dimensions that are similar to the descriptions of B. cinerea (11 × 11 to 15 μm) that causes gray mold of strawberry (2). The identity of B. cinerea was also confirmed by the production of numerous black sclerotia on PDA plates incubated either in the dark or under light at 20 to 24°C for 9 to 10 days. Koch's postulates were fulfilled by using 3-day-old mycelial agar discs of the fungus or a spore suspension containing 10⁵ conidia per milliliter of distilled water as inoculum. Shallow (2 × 2 × 2 mm) incisions were made on fresh sponge gourd fruits with a sterile scalpel and inoculated with either a 5-mm mycelial disc or 0.5 ml of the spore suspension. Inoculated areas were covered with moist sterile cotton, and the fruits were enclosed in a plastic bag and incubated at 20 to 24°C for 3 days. Wounded fruits inoculated with PDA discs or sterile distilled water alone served as controls. Pathogenicity tests were performed three times using five fruits in each trial. Symptoms and signs of the disease similar to those described above were observed in all (100%) the inoculated fruits, while no symptoms developed in the control fruits. Reisolation from the inoculated fruits consistently yielded B. cinerea. Reciprocal inoculations on sponge gourd, guava, and strawberry with mycelial discs or spore suspensions of a B. cinerea isolate obtained from sponge gourd, guava, and strawberry showed cross pathogenicity among isolates and hosts. Important groups of plants that are attacked by B. cinerea are vegetables, small berry fruits, ornamentals, and bulbs (1). Though 80 species of host plants, mostly shrubs and nursery plants, were reported to be the host of B. cinerea in Taiwan (3), to our knowledge, this is the first report of gray mold disease affecting sponge gourd in Taiwan. References: (1) G. N. Agrios. Plant Pathology. Academic Press. San Diego, 2005. (2) J. L. Mass, ed. Page 56 in: Compendium of Strawberry Diseases. The American Phytopathological Society. St. Paul, MN, 1984. (3). Y. Ko et al. Plant Prot. Bull. (Taiwan) 37:439, 1995.

Electro-optic narrowband multi-wavelength filter in aperiodically poled lithium niobate

We report on an iterative design scheme for and the first experimental demonstration of active narrowband multi-wavelength filters based on aperiodically poled lithium niobate crystals. A simultaneous transmission of 8 wavelengths, each with a ~0.45-nm linewidth and nearly 100% peak transmittance, was achieved in such a device. The transmission spectrum of this device can be tuned by temperature at a rate of ~0.65 nm/ degrees C.

Improved HPLC-MS/MS method for determination of isoxaflutole (balance) and its metabolites in soils and forage plants

A robust multi-residue procedure is needed for the analysis of the pro-herbicide isoxaflutole and its degradates in soil and plant materials at environmentally relevant (<1 microg kg-1) levels. An analytical method using turbo-spray and heat-nebulizer high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was developed for the analysis of isoxaflutole (IXF) and its two metabolites, diketonitrile (DKN) and the benzoic acid metabolite (BA), at sub-microgram per kilogram levels in soil and plant samples. The average recoveries of the three compounds in spiked soil and plant samples ranged from 84 to 110% and 94 to 105%, respectively. The limits of quantification were validated at 0.06 microg kg-1 for soil and 0.3 microg kg-1 for plant samples. The limits of detection (LOD) for soil analysis were 0.01, 0.002, and 0.01 microg kg-1 for IXF, DKN, and BA, respectively. Corresponding LOD for the plant analysis method were 0.05, 0.01, and 0.05 microg kg-1. The developed method was validated using forage grass and soil samples collected from a field lysimeter study in which IXF was applied to each of four forage treatments. Forage plants and soils were sampled for analyses 25 days after IXF application to the soil. In soils, IXF was not detected in any treatment, and DKN was the predominant metabolite found. In forage plants, the concentrations of DKN and BA were 10-100-fold higher than that in soil samples, but IXF was not detected in any forage plants. The much higher proportion of BA to DKN in plant tissues (23-53%), as compared to soils (0-5%), suggested that these forages were capable of detoxifying DKN. The developed methods provided LODs at sub-microgram per kilogram levels to determine the fate of IXF and its metabolites in soils and forage plants, and they also represent considerable improvements in extraction recovery rates and detection sensitivity as compared to previous analytical methods for these compounds.

Reaction pathways of the diketonitrile degradate of isoxaflutole with hypochlorite in water

Isoxaflutole (IXF; Balance) belongs to a new class of isoxazole herbicides. Isoxaflutole has a very short half-life in soil and rapidly degrades to a stable and phytotoxic degradate, diketonitrile (DKN). DKN was previously discovered to rapidly react with hypochlorite (OCl-) in tap water, yielding the benzoic acid (BA) degradate as a major product, but the complete reaction pathway and mechanism have not been elucidated. Thus, the objectives of this work were to (1) determine the stoichiometry of the reaction between DKN and OCl-; (2) identify products in addition to BA; and (3) propose a complete pathway and reaction mechanism for oxidation of DKN by OCl-. Stoichiometry of the reaction showed a molar ratio of OCl-/DKN of 2. In addition, two previously uncharacterized chlorinated intermediates were identified under conditions in which OCl- was the limiting reactant. The proposed chemical structure of a chlorinated benzoyl intermediate was inferred from a series of HPLC/MS and HPLC/MS/MS experiments and the use of mass spectral simulation software. A chlorinated ketone intermediate was also identified using ion trap GC/MS. Two additional end products were also identified: cyclopropanecarboxylic acid (CPCA) and dichloroacetonitrile (DCAN). On the basis of the reaction stoichiometry, the structure of the chlorinated intermediates, and the identification of the products, two reaction pathways are proposed. Both pathways involve a two-step nucleophilic attack and oxidation of the diketone structure of DKN, leading to formation of BA, DCAN, and CPCA.