Fundamentals of TiO2 Photocatalysis: Concepts, Mechanisms, and Challenges

TiO2-Graphene Quantum Dots Nanocomposites for Photocatalysis in Energy and Biomedical Applications

The focus of current research in material science has shifted from “less efficient” single-component nanomaterials to the superior-performance, next-generation, multifunctional nanocomposites. TiO2 is a widely used benchmark photocatalyst with unique physicochemical properties. However, the large bandgap and massive recombination of photogenerated charge carriers limit its overall photocatalytic efficiency. When TiO2 nanoparticles are modified with graphene quantum dots (GQDs), some significant improvements can be achieved in terms of (i) broadening the light absorption wavelengths, (ii) design of active reaction sites, and (iii) control of the electron-hole (e−-h+) recombination. Accordingly, TiO2-GQDs nanocomposites exhibit promising multifunctionalities in a wide range of fields including, but not limited to, energy, biomedical aids, electronics, and flexible wearable sensors. This review presents some important aspects of TiO2-GQDs nanocomposites as photocatalysts in energy and biomedical applications. These include: (1) structural formulations and synthesis methods of TiO2-GQDs nanocomposites; (2) discourse about the mechanism behind the overall higher photoactivities of these nanocomposites; (3) various characterization techniques which can be used to judge the photocatalytic performance of these nanocomposites, and (4) the application of these nanocomposites in biomedical and energy conversion devices. Although some objectives have been achieved, new challenges still exist and hinder the widespread application of these nanocomposites. These challenges are briefly discussed in the Future Scope section of this review.

Preparation, Characterization, and Photocatalytic Properties of Self-Standing Pure and Cu-Doped TiO2 Nanobelt Membranes

A traditional hydrothermal method was modified to synthesize ultra-long sodium titanate nanobelts by simultaneously stirring the solution. The ultra-long sodium titanate nanobelts were converted to hydrogen titanate nanobelts through an ion exchanging way. A method was then used to prepare self-standing flexible large-area membranes; they were then subject to post-annealing at different temperatures to obtain a self-standing TiO2 nanobelt membrane with a slight decrease in flexibility. Cu-doped TiO2 membranes were prepared by ion exchanging and post-annealing in the same manner. X-ray diffractions, scanning electron microscopy, field-emission scanning electron microscopy, field-emission transmission electron microscopy, Fourier transform infrared spectrometry, X-ray photoelectron spectroscopy, and UV-vis spectroscopy were used to characterize the samples. Photodegradation of methylene blue (MB) water solutions was used to evaluate the photocatalytic activity. It was seen that the pure sample presented obvious visible-light responding photocatalytic activity, possibly due to the self-sensitization of the MB molecule. The UV-induced photocatalytic activity is higher because of the photoinduced holes and electrons. It was suggested that the Cu dopant induced intra-gap states from electron traps and recombination centers, resulting in the decrease in both of the visible and UV induced photocatalysis.

Efficient degradation of typical pharmaceuticals in water using a novel TiO2/ONLH nano-photocatalyst under natural sunlight

Photocatalytic degradation of typical pharmaceuticals in natural sunlight and in actual water is of great significance. In this study, the oxygen or nitrogen linked heptazine-base polymer (ONLH) was successfully incorporated with TiO₂ nanoparticles and formed a TiO₂/ONLH nanocomposite which was responded to the natural sunlight. Under natural sunlight, the TiO₂/ONLH can effectively degrade ten types of pharmaceuticals. In particular, fluoroquinolone containing N-piperazinyl, and cardiovascular drugs containing long aromatic side chains were easily degraded. The half-life of the best degradation performance of propranolol was less than 5 min. The rate constants of propranolol using the TiO₂/ONLH were approximately six- and eight-fold higher than those of pristine TiO₂ and ONLH, respectively. Two reactive species (OH and O₂^-) facilitated the rapid degradation of propranolol, which occurred primarily through the hydroxyl radical addition, ring-opening, and ipso substitution reactions. An acute toxicity test using luminescent bacteria indicated that the toxicity of the propranolol reaction solution gradually decreased with lower total organic carbon (TOC). According to the toxicity evaluation of monomer products, the TiO₂/ONLH also reduced the generation of toxic transformation products. The effects of actual water/wastewater have further shown the TiO₂/ONLH might be applied for the removal of pharmaceuticals in wastewater.

Recent Progresses of Superhydrophobic Coatings in Different Application Fields: An Overview

With the development of material engineering and coating industries, superhydrophobic coatings with exceptional water repellence have increasingly come into researchers’ horizons. The superhydrophobic coatings with corrosion resistance, self-cleaning, anti-fogging, drag-reduction, anti-icing properties, etc., meet the featured requirements from different application fields. In addition, endowing superhydrophobic coatings with essential performance conformities, such as transparency, UV resistance, anti-reflection, water-penetration resistance, thermal insulation, flame retardancy, etc. plays a remarkable role in broadening their application scope. Various superhydrophobic coatings were fabricated by diverse technologies resulting from the fundamental demands of different fields. Most past reviews, however, provided only limited information, and lacked detailed classification and presentation on the application of superhydrophobic coatings in different sectors. In the current review, we will highlight the recent progresses on superhydrophobic coatings in automobile, marine, aircraft, solar energy and architecture-buildings fields, and discuss the requirement of prominent functionalities and performance conformities in these vital fields. Poor durability of superhydrophobic coating remains a practical challenge that needs to be addressed through real-world application. This review serves as a good reference source and provides insight into the design and optimization of superhydrophobic coatings for different applications.

Cotton fabric loaded with self-dispersive and reactive biphasic TiO2 for durable self-cleaning activity and ultraviolet protection

Self-dispersive and reactive biphasic TiO₂ (TiO₂/KH550/SAT) with negative charge was achieved by introducing sulfonic groups and chlorine atoms, respectively, and combined with cotton fabric by the covalent bonding.

Polyimide with enhanced π stacking for efficient visible-light-driven photocatalysis

Polyimide photocatalysts with enhanced π stacking are prepared through the solvothermal condensation of pyromellitic dianhydride and N,N-dialkylmelamine, exhibiting extended light absorption ranges and efficient visible-light-driven photocatalysis.

Core–shell carbon colloid sphere@phosphotungstic acid/CdS as a Z-scheme heterojunction with synergistic adsorption, photothermal and photocatalytic performance

Core–shell carbon colloid sphere@phosphotungstic acid/CdS exhibits excellent visible-light-driven photocatalytic performance, which is due to the Z-scheme heterojunction favoring the charge transfer and spatial charge separation and the photothermal effect.

Structural features and morphology of titanium dioxide–bismuth vanadate heterojunctions

Titanium dioxide TiO2 (TO) and bismuth vanadate BiVO4 (BVO) are promising photoactive semiconducting oxides for heterogeneous photocatalysis devoted to water treatment, pollutant degradation and water splitting processes.

Facile synthesis of a mesoporous TiO2 film templated by a block copolymer for photocatalytic applications

Large-sized mesoporous TiO2 through a polymeric micelle assembly approach for photocatalysts.

The Hubbard-U correction and optical properties of d0 metal oxide photocatalysts

We report a systematic investigation of individual and multisite Hubbard-U corrections for the electronic, structural, and optical properties of the metal titanate oxide d⁰ photocatalysts SrTiO₃ and rutile/anatase TiO₂. Accurate bandgaps for these materials can be reproduced with local density approximation and generalized gradient approximation exchange-correlation density functionals via a continuous series of empirically derived U^d and U^p combinations, which are relatively insensitive to the choice of functional. On the other hand, lattice parameters are much more sensitive to the choice of U^d and U^p, but in a systematic way that enables the U^d and U^p corrections to be used to qualitatively gauge the extent of self-interaction error in the electron density. Modest U^d corrections (e.g., 4 eV-5 eV) yield the most reliable dielectric response functions for SrTiO₃ and are comparable to the range of U^d values derived via linear response approaches. For r-TiO₂ and a-TiO₂, however, the U^d,p corrections that yield accurate bandgaps fail to accurately describe both the parallel and perpendicular components of the dielectric response function. Analysis of individual U^d and U^p corrections on the optical properties of SrTiO₃ suggests that the most consequential of the two individual corrections is U^d, as it predominately determines the accuracy of the dominant excitation from O-2p to the Ti-3d t_2g/e_g orbitals. U^p, on the other hand, can be used to shift the entire optical response uniformly to higher frequencies. These results will assist high-throughput and machine learning approaches to screening photoactive materials based on d⁰ photocatalysts.

Photocatalytic Degradation of Quinoline Yellow over Ag3PO4

In this study, the ability of Ag3PO4 to achieve the photocatalytic degradation of quinoline yellow (QY) a hazardous and recalcitrant dye, under UVA and visible light was investigated. The photocatalyst Ag3PO4 was synthesized through a precipitation method, and characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), BET Brunauer–Emmett-Teller (BET) analysis, UV-Differential Reflectance Spectroscopy (DRS) and Fourier transform infrared spectroscopy (FTIR). Ag3PO4 could successfully induce the photocatalytic degradation of QY under UVA and visible light. Optimal parameters were 0.5 g·L−1 of the catalyst, 20 ppm of QY and pH~7. Ag3PO4 was 1.6-times more efficient than TiO2 Degussa P25 under UVA light in degrading QY. Total organic carbon (TOC) analyses confirmed the almost complete QY mineralization. At least eight intermediate degradation products were identified by liquid chromatography coupled to high resolution mass spectrometry. The stability of Ag3PO4 was satisfactory as less than 5% Ag metal appeared in XRD analyses after 3 reuse cycles. These results show that under optimized conditions Ag3PO4 can efficiently achieve quinolone yellow mineralization.

Hydrothermal Synthesis of FeOOH and Fe2O3 Modified Self-Organizing Immobilized TiO2 Nanotubes for Photocatalytic Degradation of 1H-Benzotriazole

In this study, titanium dioxide nanotubes were prepared by electrochemical anodization technique and modified with an aqueous solution of FeCl3 using hydrothermal synthesis method to control the amount and distribution of iron compounds on the anatase TiO2 nanotubes. The objective was to synthesize immobilized FeOOH@TiO2 or Fe2O3@TiO2 photocatalysts designed for the flow-through reactor systems; to investigate thermal treatment effect on the photocatalytic efficiency; to determine appropriate Fe-compounds concentration for the maximum photocatalytic activity improvement, and to explain the mechanism responsible for the enhancement. The photocatalysts were tested for the degradation of 1H-benzotriazole in water under UV/solar light irradiation. Up to two times increase in the photocatalytic activity was obtained when TiO2 nanotubes were modified with 0.8 mM Fe. At higher Fe concentrations (8 mM and 80 mM), the photocatalytic activity of the given photocatalysts decreased. To confirm the formation of FeOOH or Fe2O3 species, and to clarify the mechanism of photoactivity, X-ray diffraction (XRD), Raman spectroscopy (RS), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray spectroscopy (EDS) and UV-Vis spectroscopy were used.

Biohybrid Cells for Photoelectrochemical Conversion Based on the HCOO--CO2 Circulation Approach

Biohybrid photoelectrochemical systems could combine the light-harvesting ability of semiconductor photocatalysts and the CO₂-processing capability of biocatalysts to realize CO₂ reduction. How to develop the energy-utilized model can be of importance for the mechanism exploration of photosynthesis. Here, a biohybrid photoelectrochemical system based on HCOO^--CO₂ circulation was developed to realize the conversion both of solar-to-electric energy and chemical-to-electric energy. The device consists of a TiO₂ nanoparticle photoanode and a laser-scribed graphene/formate dehydrogenase biocathode, which was utilized for the formic acid oxidation and the biocatalysis reduction of CO₂ to HCOO^-, respectively. The as-proposed biohybrid photoelectrochemical system exhibits good performance with an open-circuit potential of 0.93 V and a maximum power output density of 76 μW cm^-2. This ingenious strategy not only exploits a robust carbon circulation system for the conversion of solar energy but also provides a way of constructing complex artificial photosynthesis systems.

Photocatalytic degradation of microcystin-LR by modified TiO2 photocatalysis: A review

Microcystin-LR (MC-LR), the most toxic and commonly encountered cyanotoxin, is produced by harmful cyanobacterial blooms and potentially threatens human and ecosystems health. Titanium dioxide (TiO₂) photocatalysis is attracting growing attention and has been considered as an efficient, environmentally friendly and promising solution to eliminate MC-LR in the aquatic ecosystems. Over recent decades, scientific efforts have been directed towards the understanding of fundamentals, modification strategies, and application potentials of TiO₂ photocatalysis in degrading MC-LR. In this article, recent reports have been reviewed and progress has been summarized in the development of heterogeneous TiO₂-based photocatalysts for MC-LR photodegradation under visible, UV, or solar light. The proposed photocatalytic principles of TiO₂ and destruction of MC-LR have been thoroughly discussed. Specifically, some main modification methods for improving the drawbacks and performance of TiO₂ nanoparticle were highlighted, including element doping, semiconductor coupling, immobilization, floatability amelioration and magnetic separation. Moreover, the performance evaluation metrics quantum yield (QY) and figure of merit (FOM) were used to compare different photocatalysts in MC-LR degradation. The best performance was seen in N-TiO₂ with QY and FOM values of 2.20E-07 molecules/photon and 1.00E-11 mol·L/(g·J·h). N-TiO₂ or N-TiO₂-based materials may be excellent options for photocatalyst design in terms of MC-LR degradation. Finally, a summary of the remaining challenges and perspectives on new tendencies in this exciting frontier and still an emerging area of research were addressed accordingly. Overall, the present review will offer a deep insight for understanding the photodegradation of MC-LR with modified TiO₂ to further inspire researchers that work in associated fields.

Observation of Molecular Hydrogen Produced from Bridging Hydroxyls on Anatase TiO2(101)

Anatase TiO₂ is used extensively in a wide range of catalytic and photocatalytic processes and is a promising catalyst for hydrogen production. Here, we show that molecular hydrogen was produced from bridging hydroxyls (HO_b) on the (101) surface of single-crystal anatase (TiO₂(101)). This stands in contrast to rutile TiO₂(110), where HO_b pairs react to form H₂O. Electron bombardment at 30 K produced bridging oxygen vacancies in the surface. Deuterated bridging hydroxyls (DO_b) were subsequently formed via dissociation of adsorbed D₂O and confirmed by infrared reflection-absorption spectroscopy. During temperature-programmed desorption (TPD) spectroscopy, D₂ desorption was observed at 520 K. Density functional theory calculations show that both H₂ and H₂O production from HO_b are endothermic at 0 K on TiO₂(101), but H₂ (H₂O) desorption is entropically driven above 230 K (800 K). The calculated activation barrier for H₂ desorption is 1.40 eV, which is similar to the desorption energy obtained from analysis of the D₂ TPD spectra. The H₂ desorption likely proceeds in two steps: H atom diffusion on the surface and then recombination.

Photocatalytic Advanced Oxidation Processes for Water Treatment: Recent Advances and Perspective

Nowadays, an ever-increasing variety of organic contaminants in water has caused hazards to the ecological environment and human health. Many of them are persistent and non-biodegradable. Various techniques have been studied for sewage treatment, including biological, physical and chemical methods. Photocatalytic advanced oxidation processes (AOPs) have received increasing attention due to their fast reaction rates and strong oxidation capability, low cost compared with the non-photolytic AOPs. This review is dedicated to summarizing up-to-date research progress in photocatalytic AOPs, such as Fenton or Fenton-like reaction, ozonation and sulfate radical-based advanced oxidation processes. Mechanisms and activation processes are discussed. Then, the paper summarizes photocatalytic materials and modification strategies, including defect chemistry, morphology control, heterostructure design, noble metal deposition. The future perspectives and challenges are also discussed.

Hexafluorotitanic acid-assisted synthesis of large-sized, ultrathin titania nanosheets as multifunctional and high-performance photocatalysts

A fast cyclohexanol solvothermal pathway was developed to prepare highly dispersed anatase titania (TiO₂) nanosheets with an edge length of ∼800 nm and a thickness of ∼6 nm. Under the synergistic control of hexafluorotitanic acid and cyclohexanol, the exposed 001 facets reached ∼98.5% on the TiO₂ nanosheets obtained by the treatment at 180 °C for 150 min. Moreover, it was found that the phase transformation and structural development drastically occurred during the solvothermal treatment. When used as a catalyst for photodegradation of rhodamine B, the TiO₂ nanosheets exhibited a good recycling stability and a much higher photocatalytic degradation rate (nearly 99% degradation within 2.5 h) than the commercial P25 (93.6%). After being uniformly loaded with 4 wt.% of the Pt nanoparticles, the TiO₂ nanosheets displayed a photocatalytic hydrogen production rate of 2.239 mmol g^-1 h^-1 under simulated solar light, which was much higher than the pristine TiO₂ nanosheets (0.045 mmol g^-1 h^-1) as well as most of the reported TiO₂-based photocatalysts. The remarkable photocatalytic activity and good stability of the TiO₂ nanosheets with highly exposed 001 facets would make them find potential applications in both water treatment and hydrogen generation from water splitting under solar light.

Progress in Graphene/Metal Oxide Composite Photocatalysts for Degradation of Organic Pollutants

The sewage discharge of industrial wastewater seriously pollutes the water source and rivers, which is very harmful to the health of humans and wildlife. Among those methods for treating wastewater, photocatalysis is a sustainable and environmental-friendly technique for removing the organic pollutants with no secondary pollution. As a popular photocatalyst, graphene/metal oxide nanocomposites have been widely reported in the photocatalysis field. In this review, the recent progress of graphene/metal oxide composites including binary and ternary composites is summarized in detail. The synthesis, microstructure design, and application performance of graphene/TiO2, graphene/ZnO, graphene/SnO2, graphene/WO3, graphene/Fe2O3, and graphene/Cu2O composites are introduced firstly. Then, the synthesis, the selection of components, and the performance of various ternary composites are summarized specifically, including graphene/TiO2-, graphene/ZnO-, graphene/SnO2-, graphene/Cu2O-, graphene/FexOy-, and graphene/Bi-containing ternary composites. At last, the possible research directions of graphene/metal oxide nanocomposites are put forward. The main purpose is to provide a theoretical guidance for designing high-performance graphene/metal oxide photocatalysts for wastewater treatment.

Photocatalytic and bactericidal properties and molecular docking analysis of TiO2 nanoparticles conjugated with Zr for environmental remediation

Despite implementing several methodologies including a combination of physical, chemical and biological techniques, aquatic and microbial pollution remains a challenge to this day. Recently, nanomaterials have attracted considerable attention due to their extraordinary prospective for utilization toward environmental remediation. Among several probable candidates, TiO2 stands out due to its potential for use in multifaceted applications. One way to improve the catalytic and antimicrobial potential of TiO2 is to dope it with certain elements. In this study, Zr-doped TiO2 was synthesized through a sol-gel chemical method using various dopant concentrations (2, 4, 6, and 8 wt%). Surface morphological, microstructural and elemental analysis was carried out using FESEM and HR-TEM along with EDS to confirm the formation of Zr-TiO2. XRD spectra showed a linear shift of the (101) anatase peak to lower diffraction angles (from 25.4° to 25.08°) with increasing Zr4+ concentration. Functional groups were examined via FTIR, an ample absorption band appearing between 400 and 700 cm-1 in the acquired spectrum was attributed to the vibration modes of the Ti-O-Ti linkage present within TiO2 nanoparticles, which denotes the formation of TiO2. Experimental results indicated that with increasing dopant concentrations, photocatalytic potential was enhanced significantly. In this respect, TiO2 doped with 8 wt% Zr (sample 0.08 : 1) exhibited outstanding performance by realizing 98% elimination of synthetic MB in 100 minutes. This is thought to be due to a decreased rate of electron-hole pair recombination that transpires upon doping. Therefore, it is proposed that Zr-doped TiO2 can be used as an effective photocatalyst material for various environmental and wastewater treatment applications. The good docking scores and binding confirmation of Zr-doped TiO2 suggested doped nanoparticles as a potential inhibitor against selected targets of both E. coli and S. aureus. Hence, enzyme inhibition studies of Zr-doped TiO2 NPs are suggested for further confirmation of these in silico predictions.

Size-dependent interaction of plasma with anatase TiO2 nanoparticles

We study the particle size distribution and phase changes of the anatase TiO2 nanopowder samples when they are subject to the plasma treatments of three different kinds of gases as nitrogen (N2), oxygen (O2), and argon (Ar). The plasma gas pressures vary as 0.1, 0.3, and 0.6 Torr. We demonstrate that the plasma treatments have an effect neither on the phase structure nor on the mean nanocrystalline size. The phase and size invariances of the samples are attributed to their nanoscale thermodynamic aspects. We find out that elevating the gas pressure in some cases creates fine-size amorphous nanoparticles with a narrow distribution. Our findings authenticate that plasma treatment affects the amorphous phase with etching particles down to a mean value of ∼3 nm. The small-angle X-ray scattering (SAXS) technique was utilized to obtain the size distribution of the nanoparticles, and the wide-angle X-ray scattering (WAXS) technique was used to probe the phase and size changes of the crystalline structure.

Highly Active Rutile TiO2 Nanocrystalline Photocatalysts

The controllable synthesis of rutile TiO₂ single crystal particles with the preferential orientation of {111} facets still remains a scientific and technological challenge. Here, we developed a facile route for fabrication of rutile TiO₂ nanorod crystals (RTiO₂NRs) having high ratios of oxidative {111} to reductive {110} surfaces. RTiO₂NRs were synthesized using a peroxo-titanium complex (PTC) approach, which was controlled by changing the Ti/H₂O₂ ratio. The thus obtained RTiO₂NRs revealed a high tendency to agglomerate through orientation-dependent attachment along the {110} facets. This resulted in an increased {111}/{110} surface ratio and led to a markedly improved photocatalytic activity of RTiO₂NR aggregates. The reported findings illustrate the rich potential of the herein proposed facile and energy-efficient synthesis of nanostructured rutile TiO₂-based photocatalysts.

Mg-O-Bridged Polypyrrole/g-C3 N4 Nanocomposites as Efficient Visible-Light Catalysts for Hydrogen Evolution

It is highly desired to improve the visible-light activity of g-C₃ N₄ for H₂ evolution by constructing closely contacted heterojunctions with conductive polymers. Herein, a polymer nanocomposite photocatalyst with high visible-light activity is fabricated successfully by coupling nanosized polypyrrole (NPPy) particles onto g-C₃ N₄ nanosheets through a simple wet-chemical process, and its visible-light activity is improved further by constructing Mg-O bridges between the NPPy and g-C₃ N₄ . The amount-optimized bridged nanocomposite displays an approximately ninefold improvement in visible-light activity compared with g-C₃ N₄ . On the basis of transient-state surface photovoltage responses, photoluminescence spectra, ^. OH amount evaluation, and photoelectrochemical curves, it is concluded that the exceptional photoactivity can be attributed to the significantly promoted charge transfer and separation along with visible photosensitization from NPPy. Interestingly, it is confirmed that the promoted charge separation depends mainly on the excited high-level electron transfer from g-C₃ N₄ to NPPy by single-wavelength photocurrent action spectra. This work provides a feasible strategy for designing polymer nano-heterojunction photocatalysts with exceptional visible-light activities.

Facile Preparation of WO3-x Dots with Remarkably Low Toxicity and Uncompromised Activity as Co-reactants for Clinical Diagnosis by Electrochemiluminescence

The exceptional nature of WO_3-x dots has inspired widespread interest, but it is still a significant challenge to synthesize high-quality WO_3-x dots without using unstable reactants, expensive equipment, and complex synthetic processes. Herein, the synthesis of ligand-free WO_3-x dots is reported that are highly dispersible and rich in oxygen vacancies by a simple but straightforward exfoliation of bulk WS₂ and a mild follow-up chemical conversion. Surprisingly, the WO_3-x dots emerged as co-reactants for the electrochemiluminescence (ECL) of Ru(bpy)₃ ²⁺ with a comparable ECL efficiency to the well-known Ru(bpy)₃ ²⁺ /tripropylamine (TPrA) system. Moreover, compared to TPrA, whose toxicity remains a critical issue of concern, the WO_3-x dots were ca. 300-fold less toxic. The potency of WO_3-x dots was further explored in the detection of circulating tumor cells (CTCs) with the most competitive limit of detection so far.

Research progress of TiO2 photocathodic protection to metals in marine environment

Corrosion protection has become an important issue as the amount of infrastructure construction in marine environment increased. Photocathodic protection is a promising method to reduce the corrosion of metals, and titanium dioxide (TiO₂) is the most widely used photoanode. This review summarizes the progress in TiO₂ photogenerated protection in recent years. Different types of semiconductors, including sulfides, metals, metal oxides, polymers, and other materials, are used to design and modify TiO₂. The strategy to dramatically improve the efficiency of photoactivity is proposed, and the mechanism is investigated in detail. Characterization methods are also introduced, including morphology testing, light absorption, photoelectrochemistry, and protected metal observation. This review aims to provide a comprehensive overview of TiO₂ development and guide photocathodic protection.

Effect of Annealing Temperature on Spatial Atomic Layer Deposited Titanium Oxide and Its Application in Perovskite Solar Cells

In this study, spatial atomic layer deposition (sALD) is employed to prepare titanium dioxide (TiO2) thin films by using titanium tetraisopropoxide and water as metal and water precursors, respectively. The post-annealing temperature is varied to investigate its effect on the properties of the TiO2 films. The experimental results show that the sALD TiO2 has a similar deposition rate per cycle to other ALD processes using oxygen plasma or ozone oxidant, implying that the growth is limited by titanium tetraisopropoxide steric hindrance. The structure of the as-deposited sALD TiO2 films is amorphous and changes to polycrystalline anatase at the annealing temperature of 450 °C. All the sALD TiO2 films have a low absorption coefficient at the level of 10-3 cm-1 at wavelengths greater than 500 nm. The annealing temperatures of 550 °C are expected to have a high compactness, evaluated by the refractive index and x-ray photoelectron spectrometer measurements. Finally, the 550 °C-annealed sALD TiO2 film with a thickness of ~8 nm is applied to perovskite solar cells as a compact electron transport layer. The significantly enhanced open-circuit voltage and conversion efficiency demonstrate the great potential of the sALD TiO2 compact layer in perovskite solar cell applications.

Facile polyol-triggered anatase-rutile heterophase TiO2-x nanoparticles for enhancing photocatalytic CO2 reduction

Solar-driven CO₂ photoreduction into fuels has great potential in addressing the environmental and energy crisis. Heterophase TiO₂ has attracted increasing attention in photoenergy applications owing to its fascinating properties, but much more attention has been paid on photodegradation and photocatalytic water splitting than that of photocatalytic CO₂ reduction. Herein, anatase-rutile heterophase TiO₂ nanoparticles with oxygen vacancy (TiO_2-x) were successfully synthesized by involving proper amounts of polyols (EG, DEG, TEG, etc.) into the reaction system. The heterophase TiO_2-x nanoparticles could accelerate the electron-hole separation and exhibit superior photocatalytic activity for reducing CO₂ into methane. This work offers an alternative approach to simply fabricate TiO_2-x-based heterophase photocatalyst towards efficient CO₂ photoreduction.

Photolysis and TiO2 Photocatalytic Treatment under UVC/VUV Irradiation for Simultaneous Degradation of Pesticides and Microorganisms

Efficiencies of various treatments for UVC photolysis (ultraviolet light-C at 254 nm), VUV photolysis (vacuum ultraviolet light at 254 nm and 185 nm), UVC-assisted titanium dioxide photocatalysis (UVC-TiO2), and VUV-assisted titanium dioxide photocatalysis (VUV-TiO2) were investigated for the degradation of pesticides including pyraclostrobin, boscalid, fludioxonil, and azoxystrobin and inactivation of microorganisms Escherichia coli K12 as a surrogate for E. coli O157:H7 and Saccharomyces cerevisiae in aqueous solutions and on the surface of fresh cut carrots. The degradation efficiencies of VUV were higher than for UVC on pesticides in aqueous solutions. However, there was no significant difference between degradation efficiencies for UVC and UVC-TiO2 treatments, and between VUV and VUV-TiO2 treatments. UVC, VUV, UVC-TiO2, and VUV-TiO2 showed similar inactivation effects against E. coli K12 and S. cerevisiae in aqueous solutions. The combined use of UVC and VUV treatments (combined UV) and combined use of UVC-TiO2 and VUV-TiO2 treatments (combined UV-TiO2) showed higher efficiencies (72–94% removal) for the removal of residual pesticides on fresh cut carrots than bubble water washing (53–73% removal). However, there was no significant difference in removal efficiency between combined UV and combined UV-TiO2 treatments. For E. coli K12 and S. cerevisiae on fresh cut carrots, the combined UV-TiO2 treatment (1.5 log and 1.6 log reduction, respectively) showed slightly higher inactivation effects than combined UV (1.3 log and 1.2 log reduction, respectively). Photolysis and TiO2 photocatalytic treatments under UV irradiation, including VUV as a light source, showed potential for the simultaneous degradation of pesticides and microorganisms as a non-chemical and residue-free technique for surface disinfection of fresh produce.

Dye degradation performance, bactericidal behavior and molecular docking analysis of Cu-doped TiO2 nanoparticles

Copper-doped TiO2 was prepared with a sol-gel chemical method. Various concentrations (3, 6, and 9 wt%) of Cu dopant were employed. Several techniques were implemented to assess the structural, optical, morphological and chemical properties of the synthesized samples. Evaluation of elemental composition using SEM-EDS and XRF techniques showed the presence of dopant element in the prepared samples. XRD analysis confirmed the presence of anatase (TiO2) phase with interstitial doping. Incorporation of dopant was observed to enhance the crystallinity and increase the crystallite size of the synthesized products. SAED profiles revealed a high degree of crystallinity in the prepared specimens, which was also evident in the XRD spectra. Optical properties studied using UV-vis spectroscopy depicted a shift of the maximum absorption to the visible region (redshift) that signified a reduction in the band gap energy of Cu-doped TiO2 samples. Examination of morphological features with scanning and high-resolution transmission electron microscopes revealed the formation of spherical nanoparticles with a tendency to agglomerate with increasing dopant concentration. Molecular vibrations and the formation of Ti-O-Ti bonds were revealed through FTIR spectra. PL spectroscopy recorded the trapping efficiency and migration of charge carriers, which exhibited electron-hole recombination behavior. Doped nanostructures showed enhanced bactericidal performance and synergism against S. aureus and E. coli. In summary, Cu-doped TiO2 nanostructures were observed to impede bacteria effectively, which is deemed beneficial in overcoming ailments caused by pathogens such as microbial etiologies. Furthermore, molecular docking analysis was conducted to study the interaction of Cu-doped TiO2 nanoparticles with multiple proteins namely β-lactamase (binding score: -4.91 kcal mol-1), ddlB (binding score: -5.67 kcal mol-1) and FabI (binding score: -6.13 kcal mol-1) as possible targets with active site residues. Dye degradation/reduction of control and Cu-doped samples were studied through absorption spectroscopy. The obtained outcomes of the performed experiment indicated that the photocatalytic activity of Cu-TiO2 enhanced with increasing dopant concentration, which is thought to be due to a decreased rate of electron-hole pair recombination. Consequently, it is suggested that Cu-TiO2 can be exploited as an effective candidate for antibacterial and dye degradation applications.

Porous Layered Double Hydroxide/TiO2 Photocatalysts for the Photocatalytic Degradation of Orange II

Layered Double Hydroxide (LDH)/TiO2 nanocomposites with photocatalytic properties were synthesized by both impregnation and the direct coprecipitation of LDH matrices using a colloidal suspension of TiO2 nanoparticles. While the two methods led to an efficient TiO2 nanoparticle immobilization, the direct coprecipitation allowed us to tune the amount of immobilized TiO2 within the materials. The LDH/TiO2 nanocomposites obtained were deeply characterized by chemical analysis (ICP-AES), Powder X-ray diffraction (XRD), Fourier Transformed Infra-Red (FTIR), Thermogravimetric analysis (TGA), and High-Resolution Transmission Electron Microscopy (HRTEM). Clearly, the immobilization of TiO2 by direct coprecipitation promoted a modification of the textural properties and a net increase in the surface area. The crystallized TiO2 nanoparticles can be distinctly visualized by HRTEM at the surface of the layered material. Several parameters, such as the nature of the chemical composition of LDH (ZnAl and MgAl), the method of immobilization and the amount of TiO2, were shown to play a crucial role in the physicochemical and photocatalytic properties of the nanocomposites. The photocatalytic efficiency of the different LDH/TiO2 nanocomposites was investigated using the photodegradation of a model pollutant, the Orange II (OII), and was compared to a pure TiO2 colloidal solution. The degradation tests revealed that the nanocomposite obtained from MgAl LDH at a low MgAl LDH/TiO2 ratio was the most efficient for the photodegradation of OII leading to complete mineralization in 48 h.

Solution-Based Deposition of Transparent Eu-Doped Titanium Oxide Thin Films for Potential Security Labeling and UV Screening

Transparent titanium oxide thin films attract enormous attention from the scientific community because of their prominent properties, such as low-cost, chemical stability, and optical transparency in the visible region. In this study, we developed an easy and scalable solution-based process for the deposition of transparent TiOx thin films on glass substrates. We showed that the proposed method is also suitable for the fabrication of metal-doped TiOx thin films. As proof-of-the-concept, europium Eu(III) ions were introduced into TiOx film. A photoluminescence (PL) study revealed that Eu-doped TiOx thin films showed strong red luminescence associated with ⁵D₀→⁷F_j relaxation transitions in Eu (III). We found that prepared TiOx thin films significantly reduce the transmittance of destructive UV radiation; a feature that can be useful for the protection of photovoltaic devices. In addition, transparent and luminescent TiOx thin films can be utilized for potential security labeling.

Spatially Separated Bifunctional Cocatalysts Decorated on Hollow-Structured TiO2 for Enhanced Photocatalytic Hydrogen Generation

Efficient charge separation can promote photocatalysis of semiconductors. Herein, a hollow-structured TiO₂ sphere decorated with spatially separated bifunctional cocatalysts was designed, which exhibited enhanced photocatalytic hydrogen generation. Ultrasmall-sized MO_x (M = Pd, Co, Ni, or Cu) nanoparticles (NPs) were first introduced into a zeolite via confinement synthesis, and then, hollow TiO₂ was fabricated by using the zeolite as a sacrificial template forming MO_x@TiO₂. Finally, Pt NPs were decorated on the outer shell, giving rise to MO_x@TiO₂@Pt, in which the MO_x NPs and Pt NPs acted as hole capturers and electron sinks, respectively. Thanks to the enhanced light harvesting of the hollow structure and improved charge separation induced by the smaller-sized cocatalysts as well as spatially separated bifunctional cocatalysts, the as-prepared PdO_x@TiO₂@Pt catalyst exhibited a superior photocatalytic hydrogen-generation property (0.45 mmol h^-1). This work demonstrates the advantage of the spatially separated bifunctional cocatalysts in enhancing the photocatalytic properties of semiconductors.

Surface chemistry of TiO2 connecting thermal catalysis and photocatalysis

Chemical reactions catalyzed under heterogeneous conditions have recently expanded rapidly from traditional thermal catalysis to photocatalysis due to the rising concerns about sustainable development of energy and the environment. Adsorption of reactants on catalyst surfaces, subsequent surface reactions, and desorption of products from catalyst surfaces occur in both thermal catalysis and photocatalysis. TiO₂ catalysts are widely used in thermal catalytic and photocatalytic reactions. Herein we review recent progress in surface chemistry, thermal catalysis and photocatalysis of TiO₂ model catalysts from single crystals to nanocrystals with the aim of examining if the surface chemistry of TiO₂ can bridge the fundamental understanding between thermal catalysis and photocatalysis. Following a brief introduction, the structures of major facets exposed on TiO₂ catalysts, including surface reconstructions and defects, as well as the electronic structure and charge properties, are firstly summarized; then the recent progress in adsorption, thermal chemistry and photochemistry of small molecules on TiO₂ single crystals and nanocrystals is comprehensively reviewed, focusing on manifesting the structure-(photo)activity relations and the commonalities/differences between thermal catalysis and photocatalysis; and finally concluding remarks and perspectives are given.

Metal Clusters on Semiconductor Surfaces and Application in Catalysis with a Focus on Au and Ru

Metal clusters typically consist of two to a few hundred atoms and have unique properties that change with the type and number of atoms that form the cluster. Metal clusters can be generated with a precise number of atoms, and therefore have specific size, shape, and electronic structures. When metal clusters are deposited onto a substrate, their shape and electronic structure depend on the interaction with the substrate surface and thus depend on the properties of both the clusters and those of the substrate. Deposited metal clusters have discrete, individual electron energy levels that differ from the electron energy levels in the constituting individual atoms, isolated clusters, and the respective bulk material. The properties of clusters with a focus on Au and Ru, the methods to generate metal clusters, and the methods of deposition of clusters onto substrate surfaces are covered. The properties of cluster-modified surfaces are important for their application. The main application covered here is catalysis, and the methods for characterization of the cluster-modified surfaces are described.

Design of a Silicon Photocatalyst for High-Efficiency Photocatalytic Water Splitting

Metallurgical silicon was studied for photocatalytic H₂ evolution activity. It has been found that metallurgical silicon with large particle size (above 800 nm) possesses poor photocatalytic activity because of the deteriorating photoelectric performance of the low-purity silicon. After size reduction (around 400 nm) and metal nanoparticle decoration, the photocatalytic performance was significantly enhanced to 1003.3 μmol·g^-1·h^-1. However, the photocatalytic performance of the Cu-, Ag-, and Pt-decorated silicon is degraded with the increase of time. Moreover, the degradation is independent of the metal. Electrochemical test and X-ray photoelectron spectroscopy suggested that the Mott-Schottky effect in the metal-silicon contact should be responsible for the degradation. After forming a heterojunction by vulcanizing the Ag-decorated silicon, the degradation was suppressed. Upgradation of the metal-silicon contact to form a heterojunction was a promising way to suppress the degradation and retain the high photocatalytic performance.