The X-ray photoelectron spectra of Ir, IrO2 and IrCl3 revisited

Mn-Dopant Differentiating the Ru and Ir Oxidation States in Catalytic Oxides Toward Durable Oxygen Evolution Reaction in Acidic Electrolyte

Designing an efficient and durable electrocatalyst for the sluggish oxygen evolution reaction (OER) at the anode remains the foremost challenge in developing proton exchange membrane (PEM) electrolyzers. Here, a highly active and durable cactus-like nanoparticle with an exposed heterointerface between the IrO₂ and the low oxidation state Ru by introducing a trace amount of Mn dopant is reported. The heterostructure fabrication relies on initial mixing of the Ru and Ir phases before electrochemical oxidation to produce a conjoined Ru/IrO₂ heterointerface. Benefitting from electron transfer at the heterointerface, the low oxidation state Ru species shows excellent initial activity, which is maintained even after 180 h of continuous OER test. In a half-cell test, the Mn-doped RuIr nanocactus (Mn-RuIr NCT) achieves a mass activity of 1.85 A mg_Ir+Ru ^-1 at 1.48 V_RHE , which is 139-fold higher than that of commercial IrO₂ . Moreover, the superior electrocatalytic performance of Mn-RuIr NCT in the PEM electrolysis system ensures its viability in practical uses. The results of the excellent catalytic performance for acidic OER indicate that the heterostructuring robust rutile IrO₂ and the highly active Ru species with a low oxidation state on the catalyst surface drive a synergistic effect.

Hydrogen Peroxide Generation and Hydrogen Oxidation Reactions of Vacuum-prepared Ru/Ir(111) Bimetallic Surfaces

From the viewpoint of the application of Ir-Ru alloys for anode of proton exchange membrane fuel cells (PEMFCs), hydrogen peroxide (H2O2) generation and the hydrogen oxidation reaction (HOR) properties of...

Torsion strained iridium oxide for efficient acidic water oxidation in proton exchange membrane electrolyzers

Acidic oxygen evolution reaction is crucial for practical proton exchange membrane water splitting electrolysers, which have been hindered by the high catalytic overpotential and high loading of noble metal catalysts. Here we present a torsion-strained Ta_0.1Tm_0.1Ir_0.8O_2-δ nanocatalyst with numerous grain boundaries that exhibit a low overpotential of 198 mV at 10 mA cm^-2 towards oxygen evolution reaction in 0.5 M H₂SO₄. Microstructural analyses, X-ray absorption spectroscopy and theoretical calculations reveal that the synergistic effects between grain boundaries that result in torsion-strained Ir-O bonds and the doping induced ligand effect collectively tune the adsorption energy of oxygen intermediates, thus enhancing the catalytic activity. A proton exchange membrane electrolyser using a Ta_0.1Tm_0.1Ir_0.8O_2-δ nanocatalyst with a low mass loading of 0.2 mg cm^-2 can operate stably at 1.5 A cm^-2 for 500 hours with an estimated cost of US$1 per kilogram of H₂, which is much lower than the target (US$2 per kg of H₂) set by the US Department of Energy.

Identification of the Active-Layer Structures for Acidic Oxygen Evolution from 9R-BaIrO3 Electrocatalyst with Enhanced Iridium Mass Activity

Iridium-based perovskites show promising catalytic activity for oxygen evolution reaction (OER) in acid media, but the iridium mass activity remains low and the active-layer structures have not been identified. Here, we report highly active 1 nm IrO_x particles anchored on 9R-BaIrO₃ (IrO_x/9R-BaIrO₃) that are directly synthesized by solution calcination followed by strong acid treatment for the first time. The developed IrO_x/9R-BaIrO₃ catalyst delivers a high iridium mass activity (168 A g_Ir^-1), about 16 times higher than that of the benchmark acidic OER electrocatalyst IrO₂ (10 A g_Ir^-1), and only requires a low overpotential of 230 mV to reach a catalytic current density of 10 mA cm^-2_geo. Careful scanning transmission electron microscopy, synchrotron radiation-based X-ray absorption spectroscopy, and X-ray photoelectron spectroscopy analyses reveal that, during the electrocatalytic process, the initial 1 nm IrO_x nanoparticles/9R-BaIrO₃ evolve into amorphous Ir⁴⁺O_xH_y/IrO₆ octahedrons and then to amorphous Ir⁵⁺O_x/IrO₆ octahedrons on the surface. Such high relative content of amorphous Ir⁵⁺O_x species derived from trimers of face-sharing IrO₆ octahedrons in 9R-BaIrO3 and the enhanced metallic conductivity of the Ir⁵⁺O_x/9R-BaIrO₃ catalyst are responsible for the excellent acidic OER activity. Our results provide new insights into the surface active-layer structure evolution in perovskite electrocatalysts and demonstrate new approaches for engineering highly active acidic OER nanocatalysts.

Reductive electrophilic C-H alkylation of quinolines by a reusable iridium nanocatalyst

The incorporation of a coupling step into the reduction of unsaturated systems offers a desirable way for diverse synthesis of functional molecules, but it remains to date a challenge due to the difficulty in controlling the chemoselectivity. Herein, by developing a new heterogeneous iridium catalyst composed of Ir-species (Ir^δ+) and N-doped SiO₂/TiO₂ support (Ir/N-SiO₂/TiO₂), we describe its application in reductive electrophilic mono and dialkylations of quinolines with various 2- or 4-functionalized aryl carbonyls or benzyl alcohols by utilizing renewable formic acid as the reductant. This catalytic transformation offers a practical platform for direct access to a vast range of alkyl THQs, proceeding with excellent step and atom-efficiency, good substrate scope and functional group tolerance, a reusable catalyst and abundantly available feedstocks, and generation of water and carbon dioxide as by-products. The work opens a door to further develop more useful organic transformations under heterogeneous reductive catalysis.

By developing a heterogeneous iridium catalyst composed of a N-doped SiO₂/TiO₂ support and Ir-species (Ir/N-SiO₂/TiO₂), its application in reductive electrophilic alkylation of quinolines with various aryl carbonyls or benzyl alcohols is presented.

Sacrificial Cu Layer Mediated the Formation of an Active and Stable Supported Iridium Oxygen Evolution Reaction Electrocatalyst

The production of hydrogen via a proton-exchange membrane water electrolyzer (PEM-WE) is directly dependent on the rational design of electrocatalysts for the anodic oxygen evolution reaction (OER), which is the bottleneck of the process. Here, we present a smart design strategy for enhancing Ir utilization and stabilization. We showcase it on a catalyst, where Ir nanoparticles are efficiently anchored on a conductive support titanium oxynitride (TiON_x) dispersed over carbon-based Ketjen Black and covered by a thin layer of copper (Ir/CuTiON_x/C), which gets removed in the preconditioning step. Electrochemical OER activity, stability, and structural changes were compared to the Ir-based catalyst, where Ir nanoparticles without Cu are deposited on the same support (Ir/TiON_x/C). To study the effect of the sacrificial less-noble metal layer on the catalytic performance of the synthesized material, characterization methods, namely X-ray powder diffraction, X-ray photoemission spectroscopy, and identical location transmission electron microscopy were employed and complemented with scanning flow cell coupled to an inductively coupled plasma mass spectrometer, which allowed studying the online dissolution during the catalytic reaction. Utilization of these advanced methods revealed that the sacrificial Cu layer positively affects both Ir OER mass activity and its durability, which was assessed via S-number, a recently reported stability metric. Improved activity of Cu analogue was ascribed to the higher surface area of smaller Ir nanoparticles, which are better stabilized through a strong metal–support interaction (SMSI) effect.

Single-Atom Doping and High-Valence State for Synergistic Enhancement of NiO Electrocatalytic Water Oxidation

The NiO-based electrocatalytic oxygen evolution reaction (OER) of water splitting is recognized as a promising approach to produce clean H₂ fuel. However, the OER performance is still low, and especially, the overpotential is larger than 200 mV at the current density of 10 mA cm^-2 . Herein, an Ir@IrNiO sample is prepared with single-atom (SA) Ir⁴⁺ doping and surface metallic Ir nanoparticles loaded onto the NiO. Owing to the bonding of the loaded Ir with surface-exposed Ni²⁺ , the nearby Ni atoms exist in the +3 valence state, that is, the surface-loaded Ir particles behave like a stabilizer for the Ni³⁺ sites. Under the synergistic effect of SA Ir⁴⁺ and high-valance-state Ni³⁺ , the Ir@IrNiO nanostructure effectively reduces the overpotential to 195 mV at a current density of 10 mA cm^-2 . Moreover, it gives an Ir-content-normalized current density of 0.0457 A mg_Ir ^-1 , 72.1 times higher than that of the best commercialized IrO₂ (6.33 × 10^-4 A mg_Ir ^-1 ), under the condition of 1.5 V versus reversible hydrogen electrode. Operando Raman and X-ray absorption fine-structure (XAFS) measurements reveal that there are more surface-active species of Ni³⁺ , which adsorb and activate water molecules to form Ni³⁺ -*OH at low voltage, the intermediate of Ni⁴⁺ -•O is then formed at a relatively high bias voltage, and then the •O is transferred to the SA Ir⁴⁺ sites to generate Ir⁴⁺ -O-O with OH at increased voltage. This work can help design more SA-based highly active OER materials.

Extracting Turnover Frequencies of Electron Transfer in Heterogeneous Catalysis: A Study of IrO2-TiO2 Anatase for Water Oxidation Using Ce4+ Cations

Within the context of electron transfer during the catalytic water oxidation reaction, the Ir-based system is among the most active. The reaction, mimicking photosynthesis II, requires the use of an electron acceptor such the Ce4+ cation. This complex reaction, involving adsorbed water at the interface of the metal cation and Ce4+, has mostly been studied in homogenous systems. To address the ambiguity regarding the gradual transformation of a homogenous system into a heterogeneous one, we prepared and studied a heterogeneous catalyst system composed of IrO2, with a mean particle size ranging from about 5 Å to 10 Å, dispersed on a TiO2 anatase support, with the objective of probing into the different parameters of the reaction, as well as the compositional changes and rates. The system was stable for many of the runs that were conducted (five consecutive runs with 0.18 M of Ce4+ showed the same reaction rate with TON > 56,000) and, equally importantly, was stable without induction periods. Extraction of the reaction rates from the set of catalysts, with an attempt to normalize them with respect to Ir loading and, therefore, to obtain turnover frequencies (TOF), was conducted. While, within reasonable deviations, the TOF numbers extracted from TPR and XPS Ir4f were close, those extracted from the particle shape (HR-STEM) were considerably larger. The difference indicates that bulk Ir atoms contribute to the electron transfer reaction, which may indicate that the reaction rate is dominated by the reorganization energy between the redox couples involved. Therefore, the normalization of reaction rates with surface atoms may lead to an overestimation of the site activity.

Constant Change: Exploring Dynamic Oxygen Evolution Reaction Catalysis and Material Transformations in Strontium Zinc Iridate Perovskite in Acid

While iridium-based perovskites have been identified as promising candidates for the oxygen evolution reaction (OER) in proton exchange membrane (PEM) electrolyzer applications, an improved fundamental understanding of these highly dynamic materials under reaction conditions is needed to inform more robust future catalyst design. Herein, we study the highly active SrIr_0.8Zn_0.2O₃ perovskite for the OER in acid by employing electrochemical experiments with in situ and ex situ characterization techniques to understand the dynamic nature of this material at both short and long time scales. We observe initial intrinsic OER activity improvement with electrochemical cycling as well as an initial increase of Ir oxidation state under OER conditions via in situ X-ray absorption spectroscopy. We discover that the SrIr_0.8Zn_0.2O₃ perovskite experiences an OER-induced metal to insulator transition (MIT) with extensive electrochemical cycling, caused by surface reorganization and changes to the material crystallinity that occur with exposure to an acidic and oxidizing environment. Our novel identification of an OER-induced MIT for iridate perovskites reveals an additional stability concern for iridate catalysts which are known to experience material dissolution challenges; this work ultimately aims to inform future catalyst material design for PEM water electrolysis applications.

Hydrous Hydrazine Decomposition for Hydrogen Production Using of Ir/CeO2: Effect of Reaction Parameters on the Activity

In the present work, an Ir/CeO₂ catalyst was prepared by the deposition-precipitation method and tested in the decomposition of hydrazine hydrate to hydrogen, which is very important in the development of hydrogen storage materials for fuel cells. The catalyst was characterised using different techniques, i.e., X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM) equipped with X-ray detector (EDX) and inductively coupled plasma-mass spectroscopy (ICP-MS). The effect of reaction conditions on the activity and selectivity of the material was evaluated in this study, modifying parameters such as temperature, the mass of the catalyst, stirring speed and concentration of base in order to find the optimal conditions of reaction, which allow performing the test in a kinetically limited regime.

Thermal CO Oxidation and Photocatalytic CO2 Reduction over Bare and M-Al2O3 (M = Co, Ni, Cu, Rh, Pd, Ag, Ir, Pt, and Au) Cotton-Like Nanosheets

Aluminum oxide (Al₂O₃) has abundantly been used as a catalyst, and its catalytic activity has been tailored by loading transition metals. Herein, γ-Al₂O₃ nanosheets were prepared by the solvothermal method, and transition metals (M = Co, Ni, Cu, Rh, Pd, Ag, Ir, Pt, and Au) were loaded onto the nanosheets. Big data sets of thermal CO oxidation and photocatalytic CO₂ reduction activities were fully examined for the transition metal-loaded Al₂O₃ nanosheets. Their physicochemical properties were examined by scanning electron microscopy, high-resolution transmission electron microscopy, X-ray diffraction crystallography, and X-ray photoelectron spectroscopy. It was found that Rh, Pd, Ir, and Pt-loading showed a great enhancement in CO oxidation activity while other metals negated the activity of bare Al₂O₃ nanosheets. Rh-Al₂O₃ showed the lowest CO oxidation onset temperature of 172 °C, 201 °C lower than that of bare γ-Al₂O₃. CO₂ reduction experiments were also performed to show that CO, CH₃OH, and CH₄ were common products. Ag-Al₂O₃ nanosheets showed the highest performances with yields of 237.3 ppm for CO, 36.3 ppm for CH₃OH, and 30.9 ppm for CH₄, 2.2×, 1.2×, and 1.6× enhancements, respectively, compared with those for bare Al₂O₃. Hydrogen production was found to be maximized to 20.7 ppm during CO₂ reduction for Rh-loaded Al₂O₃. The present unique pre-screening test results provided very useful information for the selection of transition metals on Al₂O₃-based energy and environmental catalysts.

Linear-Organic-Polymer-Supported Iridium Complex as a Recyclable Auto-Tandem Catalyst for the Synthesis of Quinazolinones via Selective Hydration/Acceptorless Dehydrogenative Coupling from o-Aminobenzonitriles

A linear-organic-polymer-supported iridium complex Cp*Ir@P4VP, which is designed and synthesized by the coordinative immobilization of [Cp*IrCl₂]₂ on poly(4-vinylpyridine), was proven to be an efficient heterogeneous autotandem catalyst for synthesizing quinazolinones via selective hydration/acceptorless dehydrogenative coupling from o-aminobenzonitriles. Furthermore, the synthesized catalyst was recycled five times without an obvious decrease in the catalytic activity.

Nickel Structures as a Template Strategy to Create Shaped Iridium Electrocatalysts for Electrochemical Water Splitting

Low-cost, highly active, and highly stable catalysts are desired for the generation of hydrogen and oxygen using water electrolyzers. To enhance the kinetics of the oxygen evolution reaction in an acidic medium, it is of paramount importance to redesign iridium electrocatalysts into novel structures with organized morphology and high surface area. Here, we report on the designing of a well-defined and highly active hollow nanoframe based on iridium. The synthesis strategy was to control the shape of nickel nanostructures on which iridium nanoparticles will grow. After the growth of iridium on the surface, the next step was to etch the nickel core to form the NiIr hollow nanoframe. The etching procedure was found to be significant in controlling the hydroxide species on the iridium surface and by that affecting the performance. The catalytic performance of the NiIr hollow nanoframe was studied for oxygen evolution reaction and shows 29 times increased iridium mass activity compared to commercially available iridium-based catalysts. Our study provides novel insights to control the fabrication of iridium-shaped catalysts using 3d transition metal as a template and via a facile etching step to steer the formation of hydroxide species on the surface. These findings shall aid the community to finally create stable iridium alloys for polymer electrolyte membrane water electrolyzers, and the strategy is also useful for many other electrochemical devices such as batteries, fuel cells, sensors, and solar organic cells.

Effect of Modification of Amorphous Silica with Ammonium Agents on the Physicochemical Properties and Hydrogenation Activity of Ir/SiO2 Catalysts

The modification of commercial silica with solutions of NH₄F or NH₄Cl salts, followed by thermal treatment, enabled generation of the acidic sites in SiO₂ and changed its textural properties. The use of ammonium salts solution also caused the generation of additional porosity. Using NH₄F solution caused significant decrease in the specific surface area and the increase in the average pore diameter. The number and strength of resulting acid sites depend on the nature of anion in the applied ammonium salt and the concentration of salt solution. It has been found that the sample treated with NH₄F presented higher total acidity (TPD–NH₃) and the amount as well as the strength of acid sites increased with the concentration of the used modifier. As modified amorphous SiO₂ materials used as a support for iridium (1 wt %, Ir(acac)₃) nanoparticles permitted to obtain highly active catalysts for toluene hydrogenation under atmospheric pressure. The highest activity (expressed as the apparent rate and TOF) was obtained for iridium catalysts supported on silica modified by NH₄F with the highest acidity. The modification of silica with NH₄F favors the generation of centers able to adsorb toluene, which results in higher activity of this catalyst.

Molecular Analysis of the Unusual Stability of an IrNbOx Catalyst for the Electrochemical Water Oxidation to Molecular Oxygen (OER)

Adoption of proton exchange membrane (PEM) water electrolysis technology on a global level will demand a significant reduction of today's iridium loadings in the anode catalyst layers of PEM electrolyzers. However, new catalyst and electrode designs with reduced Ir content have been suffering from limited stability caused by (electro)chemical degradation. This has remained a serious impediment to a wider commercialization of larger-scale PEM electrolysis technology. In this combined DFT computational and experimental study, we investigate a novel family of iridium-niobium mixed metal oxide thin-film catalysts for the oxygen evolution reaction (OER), some of which exhibit greatly enhanced stability, such as minimized voltage degradation and reduced Ir dissolution with respect to the industry benchmark IrO_x catalyst. More specifically, we report an unusually durable IrNbO_x electrocatalyst with improved catalytic performance compared to an IrO_x benchmark catalyst prepared in-house and a commercial benchmark catalyst (Umicore Elyst Ir75 0480) at significantly reduced Ir catalyst cost. Catalyst stability was assessed by conventional and newly developed accelerated degradation tests, and the mechanistic origins were analyzed and are discussed. To achieve this, the IrNbO_x mixed metal oxide catalyst and its water splitting kinetics were investigated by a host of techniques such as synchrotron-based NEXAFS analysis and XPS, electrochemistry, and ab initio DFT calculations as well as STEM-EDX cross-sectional analysis. These analyses highlight a number of important structural differences to other recently reported bimetallic OER catalysts in the literature. On the methodological side, we introduce, validate, and utilize a new, nondestructive XRF-based catalyst stability monitoring technique that will benefit future catalyst development. Furthermore, the present study identifies new specific catalysts and experimental strategies for stepwise reducing the Ir demand of PEM water electrolyzers on their long way toward adoption at a larger scale.

Polyvinylpyrrolidone-Stabilized Iridium Nanoparticles Catalyzed the Transfer Hydrogenation of Nitrobenzene Using Formic Acid as the Source of Hydrogen

Catalytic nitrobenzene reduction is crucial for the synthesis of 4,4-methylene diphenyl diisocyanate, which is used to produce polyurethane foams, thermoplastic elastomers, and adhesives. The stability and activity of nanoparticle catalysts are affected by surface ligands and stabilizers. We established the complete composition of 7.0 ± 1.1 nm iridium oxide nanoparticles that were stabilized by polyvinylpyrrolidone (PVP[Ir]). PVP[Ir] and its surface stabilizers were characterized using elemental analysis (EA), high-resolution X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (PXRD), FT-IR, and UV-vis spectroscopy. Notably, PVP[Ir] contained 33.8 ± 0.4% Ir. XPS binding energy analyses suggest that 7% of the Ir is Ir(0) and 93% is IrO2. Using formic acid as the source of hydrogen, PVP[Ir] catalyzed the selective hydrogenation of nitrobenzene to give aniline as the only product in 66% yield in 1 h at 160 °C in a high-pressure metal reactor. Less than 1% of the side products (azobenzene and azoxybenzene) were detected. In contrast, using alcohol as the hydrogen source led to a low yield and a poor selectivity for aniline.

IrO_{2} Surface Complexions Identified through Machine Learning and Surface Investigations

A Gaussian approximation potential was trained using density-functional theory data to enable a global geometry optimization of low-index rutile IrO_{2} facets through simulated annealing. Ab initio thermodynamics identifies (101) and (111) (1×1) terminations competitive with (110) in reducing environments. Experiments on single crystals find that (101) facets dominate and exhibit the theoretically predicted (1×1) periodicity and x-ray photoelectron spectroscopy core-level shifts. The obtained structures are analogous to the complexions discussed in the context of ceramic battery materials.

Extraordinary Stability of IrO2(110) Ultrathin Films Supported on TiO2(110) under Cathodic Polarization

Down to a cathodic potentials of -1.20 V versus the reversible hydrogen electrode, the structure of IrO₂(110) electrodes supported by TiO₂(110) is found to be stable by in situ synchrotron-based X-ray diffraction. Such high cathodic potentials should lead to reduction to metallic Ir (Pourbaix diagram). From the IrO₂ lattice parameters, determined during cathodic polarization in a H₂SO₄ electrolyte solution (pH 0.4), it is estimated that the unit cell volume increases by 1% due likely to proton incorporation, which is supported by the lack of significant swelling of the IrO₂(110) film derived from X-ray reflectivity experiments. Ex situ X-ray photoelectron spectroscopy suggests that protons are incorporated into the IrO₂(110) lattice below -1.0 V, although Ir remains exclusively in the IV+ oxidation state down to -1.20 V. Obviously, further hydrogenation of the lattice oxygen of IrO₂(110) toward water is suppressed for kinetic reasons and hints at a rate-determining chemical step that cannot be controlled by the electrode potential.

In situ studies of the cathodic stability of single-crystalline IrO2(110) ultrathin films supported on RuO2(110)/Ru(0001) in an acidic environment

We investigate with in situ surface X-ray diffraction (SXRD) and X-ray reflectivity (XRR) experiments the cathodic stability of an ultrathin single-crystalline IrO2(110) film with a regular array of mesoscopic rooflike structures that is supported on a RuO2(110)/Ru(0001) template. It turns out that the planarity of the single-crystalline IrO2(110) film is lost in that IrO2(110) oxide domains delaminate at a cathodic potential of -0.18 V. Obviously, the electrolyte solution is able to reach the RuO2(110) layer presumably through the surface grain boundaries of the IrO2(110) layer. Subsequently, the single-crystalline RuO2(110) structure-directing template is reduced to amorphous hydrous RuO2, with the consequence that the IrO2(110) film loses partly its adhesion to the template. From in situ XRR experiments we find that the IrO2(110) film does not swell upon cathodic polarization down to -0.18 V, while from in situ SXRD experiments, the lattice constants of IrO2(110) are shown to be not affected. The rooflike mesostructure of the IrO2(110) flakes remains intact after cathodic polarization to -0.18 V, evidencing that the crystallinity of IrO2(110) is retained.

Synthesis of IrO2 decorated core-shell PS@PPyNH2 microspheres for bio-interface application

In this paper, an effective approach is demonstrated for the fabrication of IrO₂-decorated polystyrene@functionalized polypyrrole (core@shell; PS@PPyNH₂) microspheres. The synthesis begins with the preparation of monodispersive PS microspheres with a diameter of 490 nm, by a process of emulsifier-free emulsion polymerization, followed by a copolymerization process involving pyrrole and PyNH₂ monomers in a PS microsphere aqueous suspension, to produce uniform PS@PPyNH₂ microspheres with a diameter of 536 nm. The loading of 2 nm IrO₂ nanoparticles onto the PS@PPyNH₂ microspheres can be easily adjusted by tuning the pH value of the IrO₂ colloidal solution and the PS@PPyNH₂ suspension. At pH 4, we successfully obtain IrO₂-decorated PS@PPyNH₂ microspheres via electrostatic attraction and hydrogen bonding simultaneously between the negatively-charged IrO₂ nanoparticles and the positively-charged PS@PPyNH₂ microspheres. These IrO₂-decorated PS@PPyNH₂ microspheres exhibit a characteristic cyclic voltammetric profile, similar to that of an IrO₂ thin film. The charge storage capacity is 5.19 mA cm^-2, a value almost five times greater than that of PS@PPyNH₂ microspheres. In addition, these IrO₂-decorated PS@PPyNH₂ microspheres exhibit excellent cell viability and biocompatibility.

High-Resolution X-ray Photoelectron Spectroscopy of an IrO2(110) Film on Ir(100)

High-resolution X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) were used to characterize IrO₂(110) films on Ir(100) with stoichiometric as well as OH-rich terminations. Core-level Ir 4f and O 1s peaks were identified for the undercoordinated Ir and O atoms and bridging and on-top OH groups at the IrO₂(110) surfaces. Peak assignments were validated by comparison of the core-level shifts determined experimentally with those computed using DFT, quantitative analysis of the concentrations of surface species, and the measured variation of the Ir 4f peak intensities with photoelectron kinetic energy. We show that exposure of the IrO₂(110) surface to O₂ near room temperature produces a large quantity of on-top OH groups because of reaction of background H₂ with the surface. The peak assignments made in this study can serve as a foundation for future experiments designed to utilize XPS to uncover atomic-level details of the surface chemistry of IrO₂(110).

Exsolution of Catalytically Active Iridium Nanoparticles from Strontium Titanate

The search for new functional materials that combine high stability and efficiency with reasonable cost and ease of synthesis is critical for their use in renewable energy applications. Specifically in catalysis, nanoparticles, with their high surface-to-volume ratio, can overcome the cost implications associated with otherwise having to use large amounts of noble metals. However, commercialized materials, that is, catalytic nanoparticles deposited on oxide supports, often suffer from loss of activity because of coarsening and carbon deposition during operation. Exsolution has proven to be an interesting strategy to overcome such issues. Here, the controlled emergence, or exsolution, of faceted iridium nanoparticles from a doped SrTiO₃ perovskite is reported and their growth preliminary probed by in situ electron microscopy. Upon reduction of SrIr_0.005Ti_0.995O₃, the generated nanoparticles show embedding into the oxide support, therefore preventing agglomeration and subsequent catalyst degradation. The advantages of this approach are the extremely low noble metal amount employed (∼0.5% weight) and the catalytic activity reported during CO oxidation tests, where the performance of the exsolved SrIr_0.005Ti_0.995O₃ is compared to the activity of a commercial catalyst with 1% loading (1% Ir/Al₂O₃). The high activity obtained with such low doping shows the possibility of scaling up this new catalyst, reducing the high cost associated with iridium-based materials.

Assembly of a Highly Active Iridium-Based Oxide Oxygen Evolution Reaction Catalyst by Using Metal-Organic Framework Self-Dissolution

The proton exchange membrane (PEM) electrolyzer for hydrogen production has multiple advantages but is greatly restricted by expensive iridium and sluggish oxygen evolution reaction (OER) kinetics. The most promising way to reduce the precious metal loading is to design and develop highly active Ir-based catalysts. In this study, a versatile approach is reported to prepare a hybrid in the form of a catalyst-support structure (Fe-IrO_x@α-Fe₂O₃, abbreviated Ir@Fe-MF) by utilizing the self-dissolving properties of Fe-MIL-101 under aqueous conditions. The formation of this hybrid is mainly due to the Ir⁴⁺ and released Fe³⁺ ions coprecipitated to assemble into Fe-IrO_x nanoparticles, and the Fe³⁺ released from the inward collapse of the metal-organic framework (MOF) spontaneously forms α-Fe₂O₃. The prepared Ir@Fe-MF-2 hybrid exhibits enhanced catalytic activity toward OER with a lower onset potential and Tafel slop, and only 260 mV overpotential is required to drive the current density to reach 10 mA cm^-2. The performed characterizations clearly indicate that the IrO₆ coordination structure is changed significantly by Fe incorporated into the IrO₂ lattice. The performed X-ray adsorption spectra (XAS) provides evidence that Ir 5d orbital degeneracy is eliminated because of multiple orbitals being semi-occupied in the presence of Fe, which is mainly responsible for the enhancement of OER activity. These findings open an opportunity for the design and preparation of more efficient OER catalysts of transition metal oxides by utilization of the MOF materials. It should be highlighted that a long-term stability of this catalyst run at a high current density in acidic conditions still faces great challenges.

Design-controlled synthesis of IrO2 sub-monolayers on Au nanoflowers: marrying plasmonic and electrocatalytic properties

We develop herein plasmonic-catalytic Au-IrO₂ nanostructures with a morphology optimized for efficient light harvesting and catalytic surface area; the nanoparticles have a nanoflower morphology, with closely spaced Au branches all partially covered by an ultrathin (1 nm) IrO₂ shell. This nanoparticle architecture optimizes optical features due to the interactions of closely spaced plasmonic branches forming electromagnetic hot spots, and the ultra-thin IrO₂ layer maximizes efficient use of this expensive catalyst. This concept was evaluated towards the enhancement of the electrocatalytic performances towards the oxygen evolution reaction (OER) as a model transformation. The OER can play a central role in meeting future energy demands but the performance of conventional electrocatalysts in this reaction is limited by the sluggish OER kinetics. We demonstrate an improvement of the OER performance for one of the most active OER catalysts, IrO₂, by harvesting plasmonic effects from visible light illumination in multimetallic nanoparticles. We find that the OER activity for the Au-IrO₂ nanoflowers can be improved under LSPR excitation, matching best properties reported in the literature. Our simulations and electrocatalytic data demonstrate that the enhancement in OER activities can be attributed to an electronic interaction between Au and IrO₂ and to the activation of Ir-O bonds by LSPR excited hot holes, leading to a change in the reaction mechanism (rate-determinant step) under visible light illumination.

Rational Design of an Iridium-Tungsten Composite with an Iridium-Rich Surface for Acidic Water Oxidation

Developing highly active and stable water oxidation catalysts with reduced cost in acidic media plays a critical role in clean energy technologies such as fuel cells and electrolyzers. Precious iridium-based oxides are still the only oxygen evolution reaction (OER) catalysts with reasonable activity and stability in acid. Herein, we design iridium-tungsten composites with a metallic tungsten-rich core and an iridium-rich surface by the sol-gel method followed by hydrogen reduction. The thus obtained iridium-tungsten catalyst shows much higher intrinsic water oxidation activity (100 mA/mg_Ir at an overpotential of 290 mV) and stability (100 h at 10 mA/cm²_geom) together with reduced iridium content (33 wt % only) as compared with pure iridium oxide. An operando method using H₂O₂ as a probe molecule is developed to determine the relative adsorption strength of the reaction intermediates (*OH and *OOH) in the OER process. Detailed characterization shows that the tungsten-incorporated surface not only modulates the adsorption energy of oxygen intermediates on iridium but also enhances the stability of iridium species in acid, while the metallic tungsten core exhibits high electrical conductivity, all of which collectively give rise to the much enhanced catalytic performance of iridium-tungsten composite in acidic water oxidation. A single-membrane electrode assembly is further prepared to demonstrate the advantages and potential application of iridium-tungsten composite in practical proton exchange membrane electrolyzers.

Kinetics of the Thermal Oxidation of Ir(100) toward IrO2 Studied by Ambient-Pressure X-ray Photoelectron Spectroscopy

Using time-lapsed ambient-pressure X-ray photoelectron spectroscopy, we investigate the thermal oxidation of single-crystalline Ir(100) films toward rutile IrO₂(110) in situ. We initially observe the formation of a carbon-free surface covered with a complete monolayer of oxygen, based on the binding energies of the Ir 4f and O 1s core level peaks. During a rather long induction period with nearly constant oxygen coverage, the work function of the surface changes continuously as sensed by the gas phase O 1s signal. The sudden and rapid formation of the IrO₂ rutile phase with a thickness above 3 nm, manifested by distinct binding energy changes and substantiated by quantitative XPS analysis, provides direct evidence that the oxide film is formed via an autocatalytic growth mechanism that was previously proposed for PbO and RuO₂.

Molecular chemisorption of N2 on IrO2(110)

We investigated adsorption of N₂ on stoichiometric and O-rich IrO₂(110) surfaces using temperature programmed desorption (TPD) experiments and density functional theory (DFT) calculations. TPD shows that N₂ desorbs predominantly from the stoichiometric-IrO₂(110) surface in a well-defined peak at 270 K for N₂ coverages below about 0.5 ML and that a shoulder centered near 235 K develops in the N₂ TPD traces as the coverage approaches saturation, indicating that adsorbed N₂ molecules destabilize at high N₂ coverages. Experiments of N₂ adsorption onto O-rich IrO₂(110) surfaces provide evidence that N₂ adsorbs exclusively on the coordinatively unsaturated Ir atoms (Ir_cus) of the surface and that pre-adsorbed O-atoms ("on-top" oxygen) stabilize adsorbed N₂ molecules, causing the main N₂ TPD peak to shift toward higher temperature with increasing oxygen coverages. Consistent with prior results, our DFT calculations predict that an N₂ molecule preferentially adsorbs into an upright configuration on an Ir_cus atom of the IrO₂(110) surface and achieves a binding energy of about 100 kJ/mol. The computed binding energy agrees well with our experimental estimate of ∼90 kJ/mol for low N₂ coverages on stoichiometric IrO₂(110). The DFT calculations also quantitatively reproduce the observed stabilization of N₂ by co-adsorption on-top O-atoms and predict the destabilization of N₂ on IrO₂(110) as the N₂ adlayer becomes crowded at high coverages.

Probing the solid-liquid interface with tender x rays: A new ambient-pressure x-ray photoelectron spectroscopy endstation at the Swiss Light Source

A new endstation to perform operando chemical analysis at solid-liquid interfaces by means of ambient pressure x-ray photoelectron spectroscopy (APXPS) is presented. The endstation is located at the Swiss Light Source and can be attached to the soft x-ray in situ spectroscopy beamline (X07DB) for solid-gas type experiments and to a tender x-ray beamline (PHOENIX I) for solid-liquid interface experiments. The setup consists of three interconnected ultrahigh vacuum chambers: one for sample preparation using surface science techniques, the analysis chamber for APXPS experiments, and an entry-lock chamber for sample transfer across the two pressure regimes. The APXPS chamber is designed to study solid-liquid interfaces stabilized by the dip and pull method. Using a three-electrode setup, the potential difference across the solid-electrolyte interface can be controlled, as is demonstrated here using an Ir(001) electrode dipped and pulled from a 0.1M KOH electrolyte. The new endstation is successfully commissioned and will offer unique opportunities for fundamental studies of phenomena that take place at solid-liquid interfaces and that are relevant for fields such as electrochemistry, photochemistry, or biochemistry, to name a few.

Mechanistic study of hydrazine decomposition on Ir(111)

Hydrogen transport and storage technology remain one of the critical challenges of the hydrogen economy. Hydrazine (N2H4) is a carbon-free hydrogen carrier which has been widely used as fuel in the field of space exploration. We have combined experiments and computer simulations in order to gain a better understanding of the N2H4 decomposition on Ir catalyst, the most efficient catalyst for hydrazine decomposition up to date. We have identified metallic Ir rather than IrO2 as the active phase for hydrazine decomposition and carried out density functional theory (DFT) calculations to systematically investigate the changes in the electronic structure along with the catalytic decomposition mechanisms. Three catalytic mechanisms to hydrazine decomposition over Ir(111) have been found: (i) intramolecular reaction between hydrazine molecules, (ii) intramolecular reaction between co-adsorbed amino groups, and (iii) hydrazine dehydrogenation assisted by co-adsorbed amino groups. These mechanisms follow five different pathways for which transition states and intermediates have been identified. The results show that hydrazine decomposition on Ir(111) starts preferentially with an initial N-N bond scission followed by hydrazine dehydrogenation assisted by the amino group produced, eventually leading to ammonia and nitrogen production. The preference for N-N scission mechanisms was rationalized by analyzing the electronic structure. This analysis showed that upon hydrazine adsorption, the π bond between nitrogen atoms becomes weaker.