An overview of photocatalytic degradation: photocatalysts, mechanisms, and development of photocatalytic membrane

Synergistic activation of persulfate by a manganese cobalt oxide/reduced graphene oxide nanocomposite with enhanced degradation of trichloroethylene

Advanced oxidation technology based on persulfate is one of the most reliable and effective technologies for the degradation of wastewater, however the key lies in developing highly efficient catalysts to activate persulfate. Herein, manganese cobalt oxide/reduced graphene oxide (MnCo2O4/rGO) nanocomposites were successfully synthesized via a facile solvothermal method and employed as a highly efficient catalyst to active persulfate for the degradation of trichloroethylene (TCE). The rGO nanosheets have large surface areas, which can increase the contact area with reactants and make the degradation more efficient. Additionally, the MnCo2O4 nanoparticles are in situ grown on the surface of ultrathin rGO nanosheets, endowing the material with high structural porosity and fast transport channels, and are beneficial for the improvement of catalytic sites and the transport of catalysis-relevant species. More importantly, the close contact between MnCo2O4 nanoparticles and rGO nanosheets synergistically favors the electron transfer, thereby accelerating the electron transfer, improving the activation efficiency, and promoting the generation of sulfate radicals (·SO4-). rGO can also reduce the spillover of metal ions. The kinetics model and degradation mechanism of the nanocomposites are also proposed.

Surfactant supported chitosan for efficient removal of Cr(VI) and anionic food stuff dyes from aquatic solutions

In order to develop a novel and cost-effective adsorbent with outstanding adsorption capacity and excellent recyclability for anionic pollutants, the chitosan-modified cetyltrimethylammonium bromide sorbent (CS@CTAB) was fabricated. Fourier-transform infrared spectroscopy, N2 adsorption-desorption isotherm, elemental analysis, Thermogravimetric analysis, X-ray diffraction, and Scanning electron microscopy have been applied to evaluate both raw and surfactant modified chitosan (CS@CTAB). Azorubine, Sunset Yellow, and hexavalent chromium were used to study the adsorption behavior of CS@CTAB under various parameters such as adsorbent dose, initial dye and metal ion concentration, contact time, and temperature. Adsorption equilibrium, kinetics models and thermodynamic parameters were investigated. The adsorption isotherm fitted well with the Langmuir isotherm model, with a maximum adsorption capacity of 492.6 mg/g, 492.6 mg/g, and 490.196 mg/g for Azorubine, Sunset Yellow, and Hexavalent Chromium, respectively. The kinetic studies showed that the pseudo-second-order model provided a better correlation between experimental data. Furthermore, the calculated thermodynamic parameters confirmed that the adsorption of Cr(VI), E110, and E122 by CS@CTAB material is a spontaneous and exothermic process. The fabricated CS@CTAB adsorbent was employed for the efficient elimination of Azorubine, Sunset Yellow, and hexavalent chromium from real water samples, synthetic mixtures, and colored soft drinks, with a percentage of recovery of ~ 96%. The plausible adsorption mechanisms of Azorubine, Sunset Yellow, and hexavalent chromium on the surface of CS@CTAB are elucidated. The adsorption anticipated to be due to electrostatic interaction and hydrogen bond formation for hexavalent chromium; while the adsorption of Azorubine and Sunset Yellow, was assumed to be due to electrostatic interaction, hydrogen bonding, and n-π interaction. Finally, the study demonstrates the efficiency of CS@CTAB for the removal of anionic species from several samples, including natural water and colored beverages.

Morphology Controlled Deposition of Vanadium Oxide (VOx) Nanoparticles on the Surface of Highly Reduced Graphene Oxide for the Photocatalytic Degradation of Hazardous Organic Dyes

Semiconducting nanomaterials based heterogeneous photocatalysis represent a low-cost, versatile technique for environmental remediation, including pollution mitigation, energy management and other environmental aspects. Herein, we demonstrate the syntheses of various heterogeneous photocatalysts based on highly reduced graphene oxide (HRG) and vanadium oxide (VOx)-based nanocomposites (HRG-VOx). Different shapes (rod, sheet and urchin forms) of VOx nanoparticles were successfully fabricated on the surface of HRG under solvo-/hydrothermal conditions by varying the amount of water and ethanol. The high concentration of water in the mixture resulted in the formation of rod-shaped VOx nanoparticles, whereas increasing the amount of ethanol led to the production of VOx sheets. The solvothermal condition using pure ethanol as solvent produced VOx nano-urchins on the surface of HRG. The as-prepared hybrid materials were characterized using various spectroscopic and microscopic techniques, including X-ray diffraction, UV-vis, FTIR, SEM and TEM analyses. The photocatalytic activities of different HRG-VOx nanocomposites were investigated for the photodegradation of methylene blue (MB) and methyl orange (MO). The experimental data revealed that all HRG-VOx composite-based photocatalysts demonstrated excellent performance toward the photocatalytic degradation of the organic dyes. Among all photocatalysts studied, the HRG-VOx nanocomposite consisting of urchin-shaped VOx nanoparticles (HRG-VOx-U) demonstrated superior photocatalytic properties towards the degradation of dyes.

An overview of biogenic metallic nanoparticles for water treatment and purification: the state of the art

The environment is fundamental to human existence, and protecting it from dangerous contaminants should be a top priority for all stakeholders. Reducing garbage output has helped, but as the world's population grows, more waste will be generated. Tons of waste inadvertently and advertently received by environmental matrixes adversely affect the sustainable environment. The pollution caused by these activities affects the environment and human health. Conventional remediation processes ranging from chemical, physical, and biological procedures use macroaggregated materials and microorganisms to degrade or remove pollutants. Undesirable limitations of expensiveness, disposal challenges, maintenance, and formation of secondary contaminants abound. Additionally, multiple stages of treatments to remove different contaminants are time-consuming. The need to avoid these limitations and shift towards sustainable approaches brought up nanotechnology options. Currently, nanomaterials are being used for environmental rejuvenation that involves the total degradation of pollutants without secondary pollution. As nanoparticles are primed with vast and modifiable reactive sites for adsorption, photocatalysis, and disinfection, they are more useful in remediating pollutants. Review articles on metallic nanoparticles usually focus on chemically synthesized ones, with a particular focus on their adsorption capacity and toxicities. Therefore, this review evaluates the current status of biogenic metallic nanoparticles for water treatment and purification.

Controlled Size Oils Based Green Fabrication of Silver Nanoparticles for Photocatalytic and Antimicrobial Application

The particle size at the nanometric level allows the manifestation of remarkable properties, chiefly due to changes in surface-to-volume ratio. This study is attributed to the novel green synthesis of nano silver by using essential oils as a capping and reducing agent. Clove oil, cinnamon oil, and cardamom oil were selected for the eco-friendly and low-cost fabrication of silver nanoparticles. The prepared nanoparticles were characterized by photoluminescence spectroscopy, FT-IR spectroscopy, X-Ray diffraction, energy dispersive X-ray spectroscopy, dynamic laser light scattering, thermogravimetric analysis, and transmission electron microscopy. It was found that samples prepared by using cinnamon oil (20 nm) and cardamom oil (12 nm) had smaller particle sizes as compared to those synthesized by using clove oil (45 nm). All the prepared samples exhibited very strong antimicrobial activities with a clear zone of inhibition (6-24 mm) against Staphylococcus aureus, Klebsiella pneumoniae, and Candida albicans. Very resilient photocatalytic activities of the samples were observed against Allura red and fast green dyes. It was concluded that the cinnamon oil-based system is the best size reducer and size homogenizer (less chances of agglomeration) as compared to clove oil and cardamom oil (more chances of agglomeration) for the synthesis of silver nanoparticles.

Experimental and computational study of metal oxide nanoparticles for the photocatalytic degradation of organic pollutants: a review

Photocatalysis is a more proficient technique that involves the breakdown or decomposition of different organic contaminants, various dyes, and harmful viruses and fungi using UV or visible light solar spectrum. Metal oxides are considered promising candidate photocatalysts owing to their low cost, efficiency, simple fabricating method, sufficient availability, and environment-friendliness for photocatalytic applications. Among metal oxides, TiO2 is the most studied photocatalyst and is highly applied in wastewater treatment and hydrogen production. However, TiO2 is relatively active only under ultraviolet light due to its wide bandgap, which limits its applicability because the production of ultraviolet is expensive. At present, the discovery of a photocatalyst of suitable bandgap with visible light or modification of the existing photocatalyst is becoming very attractive for photocatalysis technology. However, the major drawbacks of photocatalysts are the high recombination rate of photogenerated electron-hole pairs, the ultraviolet light activity limitations, and low surface coverage. In this review, the most commonly used synthesis method for metal oxide nanoparticles, photocatalytic applications of metal oxides, and applications and toxicity of different dyes are comprehensively highlighted. In addition, the challenges in the photocatalytic applications of metal oxides, strategies to suppress these challenges, and metal oxide studied by density functional theory for photocatalytic applications are described in detail.

β-CD-Induced Precipitation of Eriochrome Black T Recovered via CTAB-Assisted Foam Fractionation for Adsorption of Trace Cu(II)

In order to remove and reuse the ecotoxic dye Eriochrome black T (EBT) from dyeing wastewater, we used a process called cetyltrimethylammonium bromide (CTAB)-assisted foam fractionation. By optimizing this process with response surface methodology, we achieved an enrichment ratio of 110.3 ± 3.8 and a recovery rate of 99.1 ± 0.3%. Next, we prepared composite particles by adding β-cyclodextrin (β-CD) to the foamate obtained through foam fractionation. These particles had an average diameter of 80.9 μm, an irregular shape, and a specific surface area of 0.15 m²/g. Using these β-CD-CTAB-EBT particles, we were able to effectively remove trace amounts of Cu²⁺ ions (4 mg/L) from the wastewater. The adsorption of these ions followed pseudo-second-order kinetics and Langmuir isotherm models, and the maximal adsorption capacities at different temperatures were 141.4 mg/g at 298.15 K, 143.1 mg/g at 308.15 K, and 144.5 mg/g at 318.15 K. Thermodynamic analysis showed that the mechanism of Cu²⁺ removal via β-CD-CTAB-EBT was spontaneous and endothermic physisorption. Under the optimized conditions, we achieved a removal ratio of 95.3 ± 3.0% for Cu²⁺ ions, and the adsorption capacity remained at 78.3% after four reuse cycles. Overall, these results demonstrate the potential of β-CD-CTAB-EBT particles for the recovery and reuse of EBT in dyeing wastewater.

An Overview of Photocatalytic Membrane Degradation Development

Environmental pollution has become a worldwide issue. Rapid industrial and agricultural practices have increased organic contaminants in water supplies. Hence, many strategies have been developed to address this concern. In order to supply clean water for various applications, high-performance treatment technology is required to effectively remove organic and inorganic contaminants. Utilizing photocatalytic membrane reactors (PMRs) has shown promise as a viable alternative process in the water and wastewater industry due to its efficiency, low cost, simplicity, and low environmental impact. PMRs are commonly categorized into two main categories: those with the photocatalyst suspended in solution and those with the photocatalyst immobilized in/on a membrane. Herein, the working and fouling mechanisms in PMRs membranes are investigated; the interplay of fouling and photocatalytic activity and the development of fouling prevention strategies are elucidated; and the significance of photocatalysis in membrane fouling mechanisms such as pore plugging and cake layering is thoroughly explored.

Metal organic framework-loaded polyethersulfone/polyacrylonitrile photocatalytic nanofibrous membranes under visible light irradiation for the removal of Cr(vi) and phenol from water

In this work, various amounts of the UiO-66-NH₂ and UiO-66-NH₂/TiO₂ MOFs have been loaded into polyacrylonitrile (PAN) nanofibers supported on polyethersulfone (PES). The visible light irradiation was used to investigate the influence of pH (2-10), initial concentration (10-500 mg L^-1), and time (5-240 min) on the removal efficiency of phenol and Cr(vi) in the presence of MOFs. The reaction time: 120 min, catalyst dosage: 0.5 g L^-1, pH: 2 for Cr(vi) ions and pH: 3 for phenol molecules were optimum to degrade phenol and to reduce Cr(vi) ions. The characterization of the produced samples was performed using X-ray diffraction, ultraviolet-visible diffuse reflectance spectroscopy, scanning electron microscopy, and Brunauer-Emmett-Teller analysis. The capability of synthesized photocatalytic membranes was investigated for the removal of phenol and Cr(vi) ions from water. The water flux, Cr(vi) and phenol solutions fluxes and their rejection percentages were evaluated under pressure of 2 bar in the presence of visible light irradiation and in the dark. The best performance of the synthesized nanofibers was obtained for UiO-66-NH₂/TiO₂ MOF 5 wt% loaded-PES/PAN nanofibrous membranes at temperature of 25 °C and pH of 3. Results demonstrated the high capability of MOFs-loaded nanofibrous membranes for the removal of various contaminants such as Cr(vi) ions and phenol molecules from water.

Self-Assembly of Bi2Sn2O7/β-Bi2O3 S-Scheme Heterostructures for Efficient Visible-Light-Driven Photocatalytic Degradation of Tetracycline

Fabrication of S-scheme heterojunctions with enhanced redox capability offers an effective approach to address environmental remediation. In this study, high-performance Bi₂Sn₂O₇/β-Bi₂O₃ S-scheme heterojunction photocatalysts were fabricated via the in situ growth of Bi₂Sn₂O₇ on β-Bi₂O₃ microspheres. The optimized Bi₂Sn₂O₇/β-Bi₂O₃ (BSO/BO-0.4) degradation efficiency for tetracycline hydrochloride was 95.5%, which was 2.68-fold higher than that of β-Bi₂O₃. This improvement originated from higher photoelectron-hole pair separation efficiency, more exposed active sites, excellent redox capacity, and efficient generation of ^·O₂ ^- and ^·OH. Additionally, Bi₂Sn₂O₇/β-Bi₂O₃ exhibited good stability against photocatalytic degradation, and the degradation efficiency remained >89.7% after five cycles. The photocatalytic mechanism of Bi₂Sn₂O₇/β-Bi₂O₃ S-scheme heterojunctions was elucidated. In this study, we design and fabricate high-performance heterojunction photocatalysts for environmental remediation using S-scheme photocatalysts.

Facile Fabrication of Highly Active CeO2@ZnO Nanoheterojunction Photocatalysts

Photocatalyst performance is often limited by the poor separation and rapid recombination of photoinduced charge carriers. A nanoheterojunction structure can facilitate the separation of charge carrier, increase their lifetime, and induce photocatalytic activity. In this study, CeO₂@ZnO nanocomposites were produced by pyrolyzing Ce@Zn metal-organic frameworks prepared from cerium and zinc nitrate precursors. The effects of the Zn:Ce ratio on the microstructure, morphology, and optical properties of the nanocomposites were studied. In addition, the photocatalytic activity of the nanocomposites under light irradiation was assessed using rhodamine B as a model pollutant, and a mechanism for photodegradation was proposed. With the increase in the Zn:Ce ratio, the particle size decreased, and surface area increased. Furthermore, transmission electron microscopy and X-ray photoelectron spectroscopy analyses revealed the formation of a heterojunction interface, which enhanced photocarrier separation. The prepared photocatalysts show a higher photocatalytic activity than CeO₂@ZnO nanocomposites previously reported in the literature. The proposed synthetic method is simple and may produce highly active photocatalysts for environmental remediation.

Microplastic remediation technologies in water and wastewater treatment processes: Current status and future perspectives

Microplastics (MPs) are a type of contaminants produced during the use and disposal of plastic products, which are ubiquitous in our lives. With the high specific surface area and strong hydrophobicity, MPs can adsorb various hazardous microorganisms and chemical contaminants from the environment, causing irreversible damage to our humans. It is reported that the MPs have been detected in infant feces and human blood. Therefore, the presence of MPs has posed a significant threat to human health. It is critically essential to develop efficient, scalable and environmentally-friendly methods to remove MPs. Herein, recent advances in the MPs remediation technologies in water and wastewater treatment processes are overviewed. Several approaches, including membrane filtration, adsorption, chemically induced coagulation-flocculation-sedimentation, bioremediation, and advanced oxidation processes are systematically documented. The characteristics, mechanisms, advantages, and disadvantages of these methods are well discussed and highlighted. Finally, the current challenges and future trends of these methods are proposed, with the aim of facilitating the remediation of MPs in water and wastewater treatment processes in a more efficient, scalable, and environmentally-friendly way.

Construction of SnO2/CuO/rGO nanocomposites for photocatalytic degradation of organic pollutants and antibacterial applications

Water contamination by reactive dyes is a serious concern for human health and the environment. In this study, we prepared high efficient SnO₂/CuO/rGO nanocomposites for reactive dye degradation. For structural analysis of SnO₂/CuO/rGO nanocomposites, XRD, UV-Vis DRS, SEM, TEM-EDAX, and XPS analysis were used to characterize the physicochemical properties of the material. The characterization results confirmed great crystallinity, purity, and optical characteristics features. For both Rhodamine B (RhB) and Reactive Red 120 (RR120) degradation processes, SnO₂/CuO/rGO nanocomposites were tested for their photocatalytic degradation performance. The SnO₂/CuO/rGO nanocomposites have expressed the degradation rate exposed to 99.6% of both RhB and RR120 dyes. The main reason behind the photocatalytic degradation was due to the formation of OH radical's generation by the composite materials. Moreover, the antibacterial properties of synthesized SnO₂/CuO/rGO nanocomposites were studied against E. coli, S. aureus, B. subtilis and P. aeroginosa and exhibited good antibacterial activity against the tested bacterial strains. Thus, the synthesized SnO₂/CuO/rGO nanocomposites are a promising photocatalyst and antibacterial agent. Furthermore, mechanisms behind the antibacterial effects will be ruled out in near future.

Converting synthetic azo dye and real textile wastewater into clean energy by using synthesized CuO/C as photocathode in dual-photoelectrode photocatalytic fuel cell

Cathode in photocatalytic fuel cell (PFC) plays a crucial role in degradation of organic contaminants. In this study, synthesized copper oxide (CuO) was loaded on carbon plate and used as photocathode in PFC for degradation of synthetic azo dye Reactive Black 5 (RB5) and real textile wastewater. Morphology and structural phase of the synthesized CuO were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. Several operating parameters had been investigated such as light irradiation, initial dye concentration, and pH of azo dye solution within 6 h of irradiation time. The lowest initial concentration of RB5 (10 mg L^-1) achieved 100% color removal compared to the highest initial concentration (40 mg L^-1) which only achieved 77.1% color removal within 6 h of irradiation time. The influence of external resistance was significant in electricity generation but trivial in dye degradation efficiency. The external resistance of 6000 Ω yielded highest maximum power density, with P_max of 0.2631 μW cm^-2, followed by 1000 Ω (0.2196 μW cm^-2) and 8000 Ω (0.1587 μW cm^-2), respectively. The real textile wastewater with dilution ratio (DR) 1:6 yielded the highest energy conversion efficiency, η (3.62%), followed by DR 1:4 (3.19%) and DR 1:2 (1.96%), respectively.

Bismuth-based semiconductors applied in photocatalytic reduction processes: fundamentals, advances and future perspectives

Bismuth-based semiconductors (BBSs) with their typical layered structures and unique electronic properties are considered an attractive visible light-responsive photocatalysts. Recently, BBS exhibited promising properties and was rapidly developed in photoreduction reactions. In this review, we firstly focus on the photoreduction reactions of BBS with a description of the basic principles. Specifically, the restrictive factors of the photoreduction reactions and the design directions of the catalysts are addressed. BBS photocatalysts, such as bismuth oxide, bismuth halide oxide and bismuth-based oxygenates, are presented in terms of the catalyst material design, crystal structure and other features. Furthermore, the primary applications of BBS in photoreduction reactions are described, including CO₂ reduction, N₂ reduction, H₂ evolution, and nitrate reduction. Additionally, the advances and shortages of BBS applied in these processes are summarized and comprehensively discussed. Future works for BBS applied in photoreduction processes are also proposed.

Main/side chain asymmetric molecular design enhances charge transfer of two-dimensional conjugated polymer/g-C3N4 heterojunctions for high-efficiency photocatalytic sterilization and degradation

Heterojunctions based on conjugated polymers (PHJs) are of promise as photocatalysts. Here, we fabricate the two-dimensional benzodithiophene (BDT) and thieno[2,3-f]benzofuran (TBF) based conjugated polymers/g-C₃N₄ PHJs creatively using the symmetry-breaking strategy. PD1 and PD3 with the asymmetric backbone TBF have better crystallinity. Moreover, PD3 utilizing fluorinated benzotriazole as the electron acceptor unit possesses more compact π - π stacking and higher charge mobility. The conjugated polymer PD5 with asymmetric side chains in the donor unit BDT guarantees more efficient charge transfer in the corresponding PD5/g-C₃N₄ PHJ while maintaining comparable light utilization rate. Consequently, PD5/g-C₃N₄ shows the champion performance with photocatalytic sterilization rates reaching 99.1% and 97.3% for S. aureus and E. coli. Notably, the reaction rate constant for Rhodamine B degradation of PD5/g-C₃N₄ is 8 times that of g-C₃N₄, a record high among conjugated polymers/g-C₃N₄. This study aims to reveal the structure - property correlation of asymmetric conjugated polymers/g-C₃N₄ for potential photocatalysis applications.

Effective Removal of Methylene Blue by Mn3O4/NiO Nanocomposite under Visible Light

Wastewater treatment is indispensable as wastewater can lead to adverse health effects and deteriorate the quality of life on earth. Photocatalysis is a facile methodology to address this issue. In this study, nanocomposites (NCs) of manganese oxide (Mn3O4) and nickel oxide (NiO) were synthesized in different weight ratios via the solid-state reaction route. Structural properties, optical properties, surface morphology, and functional group analysis of the synthesized nanomaterials were conducted using X-ray diffraction (XRD), UV– Vis spectroscopy, scanning electron microscopy (SEM) along with energy-dispersive X-ray (EDX) analysis, and Fourier-transform infrared (FTIR) spectroscopy, respectively. The bandgap of the nanocomposite decreases significantly from 2.35 eV for the Mn3O4 NPs to 1.65 eV for the Mn3O4/NiO nanocomposite (NC). Moreover, adsorption studies followed by the photocatalytic performance of the Mn3O4/NiO NCs were evaluated to determine the removal of methylene blue (MB) dye from wastewater. The photocatalytic performance of the nanocomposite enhances as the ratio of Mn3O4 in the composite increases from one weight percentage to three weight percentage. The photocatalytic degradation efficiency was calculated to be 95%. The results show that the synthesized NCs could play an important role in photocatalytic wastewater purification and environmental remediation.

Membrane Fabrication and Modification by Atomic Layer Deposition: Processes and Applications in Water Treatment and Gas Separation

Membrane-based separation processes are part of most water purification plants worldwide. Industrial separation applications, primarily water purification and gas separation, can be improved with novel membranes or modification to existing ones. Atomic layer deposition (ALD) is an emerging technique that is proposed to upgrade certain kinds of membranes independent of their chemistry and morphology. ALD deposits thin, defect-free, angstrom-scale, and uniform coating layers on a substrate's surface by reacting with gaseous precursors. The surface-modifying effects of ALD are described in the present review, followed by a description of various types of inorganic and organic barrier films and how these can be used in combination with ALD. The role of ALD in membrane fabrication and modification is categorized into different membrane-based groups according to the treated medium, i.e., water or gas. In all membrane types, the ALD-based direct deposition of inorganic materials, mainly metal oxides, on the membrane surface can improve antifouling, selectivity, permeability, and hydrophilicity. Therefore, the ALD technique can broaden the applications of membranes to the treatment of emerging contaminants in water and air. Finally, the advancement, limitations, and challenges of ALD-based membrane fabrication and modification are compared to provide a comprehensive guideline for developing next-generation membranes with improved filtration and separation performance.

An Overview of Recent Developments in Improving the Photocatalytic Activity of TiO2-Based Materials for the Treatment of Indoor Air and Bacterial Inactivation

Indoor air quality has become a significant public health concern. The low cost and high efficiency of photocatalytic technology make it a natural choice for achieving deep air purification. Photocatalysis procedures have been widely investigated for environmental remediation, particularly for air treatment. Several semiconductors, such as TiO₂, have been used for photocatalytic purposes as catalysts, and they have earned a lot of interest in the last few years owing to their outstanding features. In this context, this review has collected and discussed recent studies on advances in improving the photocatalytic activity of TiO₂-based materials for indoor air treatment and bacterial inactivation. In addition, it has elucidated the properties of some widely used TiO₂-based catalysts and their advantages in the photocatalytic process as well as improved photocatalytic activity using doping and heterojunction techniques. Current publications about various combined catalysts have been summarized and reviewed to emphasize the significance of combining catalysts to increase air treatment efficiency. Besides, this paper summarized works that used these catalysts to remove volatile organic compounds (VOCs) and microorganisms. Moreover, the reaction mechanism has been described and summarized based on literature to comprehend further pollutant elimination and microorganism inactivation using photocatalysis. This review concludes with a general opinion and an outlook on potential future research topics, including viral disinfection and other hazardous gases.

In-situ fabrication of manganese ferrite grafted polyaniline nanocomposite: A magnetically reusable visible light photocatalyst and a robust electrode material for supercapacitor

Herein, we reported the in-situ preparation of manganese ferrite (MnFe₂O₄) grafted polyaniline (Pani), a magnetic nanocomposite for the potential visible light photocatalytic material as well as electrode material for supercapacitor. The physical characterization of the prepared nanoparticle and nanocomposite was examined with various spectroscopic and microscopic analyses. The peaks observed in the X-ray diffraction study confirm the face-centered cubic phase of MnFe₂O₄ nanoparticles with a grain size of ∼17.6 nm. The surface morphology analysis revealed the uniform distribution of spherical-like MnFe₂O₄ nanoparticles on the surface of Pani. The degradation of malachite green (MG) dye under exposure to visible light was investigated using MnFe₂O₄/Pani nanocomposite as a photocatalyst. The results exposed the faster degradation of MG dye was accomplished by MnFe₂O₄/Pani nanocomposite than MnFe₂O₄ nanoparticles. The energy storage performance of the MnFe₂O₄/Pani nanocomposite was analyzed through cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy analyses. The results exposed that the MnFe₂O₄/Pani electrode achieved a capacitance of 287.1 F/g than the MnFe₂O₄ electrode (94.55 F/g). Further, the respectable capacitance of 96.92% was achieved even after 3000 repetitive cycles stability . Based on the outcomes, the MnFe₂O₄/Pani nanocomposite can be suggested as a promising material for both photocatalytic and supercapacitor applications.

Anchoring black phosphorous quantum dots on Bi2WO6 porous hollow spheres: A novel 0D/3D S-scheme photocatalyst for efficient degradation of amoxicillin under visible light

Reasonable regulation of the micro-morphology of material can significantly enhance the related performance. Herein, bismuth tungstate (Bi₂WO₆, simplified as BWO) porous hollow spheres with flower-like surface were prepared successfully, and this unique morphology endowed BWO with improved photocatalytic performance by reflecting and absorbing the light multiple times inside the cavity. To inhibit the rapid recombination of photogenerated e^--h⁺ pairs within BWO itself, black phosphorous quantum dots (BPQDs) were anchored onto the nanosheets of BWO sphere closely by a facile self-assembly process, which will not shade the pores of BWO owing to the small size of BPQDs, but the BP nanosheets have the chance to do that. The band gap of BPQDs expanded much after exfoliation due to the quantum confinement effects, which matched the energy band of BWO well to form S-scheme heterojunction, achieving more efficient separation of photogenerated charges. As a result, the BPQDs/BWO exhibited attractive photocatalytic performance in the degradation of amoxicillin (AMX) and other antibiotics. Besides, the operation conditions were optimized, specifically, 94.5 % of AMX (20 mg/L, 200 mL) can be removed in 60 min when 50 mg of 2BPQDs/BWO was used as catalyst with solution pH = 11. Moreover, a possible degradation pathway of AMX was proposed based on the detected intermediates.

Preparation of MnO2-Carbon Materials and Their Applications in Photocatalytic Water Treatment

Water pollution is one of the most important problems in the field of environmental protection in the whole world, and organic pollution is a critical one for wastewater pollution problems. How to solve the problem effectively has triggered a common concern in the area of environmental protection nowadays. Around this problem, scientists have carried out a lot of research; due to the advantages of high efficiency, a lack of secondary pollution, and low cost, photocatalytic technology has attracted more and more attention. In the past, MnO₂ was seldom used in the field of water pollution treatment due to its easy agglomeration and low catalytic activity at low temperatures. With the development of carbon materials, it was found that the composite of carbon materials and MnO₂ could overcome the above defects, and the composite had good photocatalytic performance, and the research on the photocatalytic performance of MnO₂-carbon materials has gradually become a research hotspot in recent years. This review covers recent progress on MnO₂-carbon materials for photocatalytic water treatment. We focus on the preparation methods of MnO₂ and different kinds of carbon material composites and the application of composite materials in the removal of phenolic compounds, antibiotics, organic dyes, and heavy metal ions in water. Finally, we present our perspective on the challenges and future research directions of MnO₂-carbon materials in the field of environmental applications.

Characterization and Gel Properties of Low-Molecular-Weight Carrageenans Prepared by Photocatalytic Degradation

Low-molecular-weight carrageenan has attracted great interest because it shows advantages in solubility, absorption efficiency, and bioavailability compared to original carrageenan. However more environment-friendly and efficient methods to prepare low-molecular-weight carrageenan are still in great need. In the present study, a photocatalytic degradation method with only TiO₂ has been developed and it could decrease the average molecular weight of κ-carrageenan to 4 kDa within 6 h. The comparison of the chemical compositions of the degradation products with those of carrageenan by FT-IR, NMR, etc., indicates no obvious removement of sulfate group, which is essential for bioactivities. Then 20 carrageenan oligosaccharides in the degradation products were identified by HPLC-MSⁿ, and 75% of them possessed AnGal or its decarbonylated derivative at their reducing end, indicating that photocatalysis is preferential to break the glycosidic bond of AnGal. Moreover, the analysis results rheology and Cryo-SEM demonstrated that the gel property decreased gradually. Therefore, the present study demonstrated that the photocatalytic method with TiO₂ as the only catalyst has the potential to prepare low-molecular-weight carrageenan with high sulfation degree and low viscosity, and it also proposed the degradation rules after characterizing the degradation products. Thus, the present study provides an effective green method for the degradation of carrageenan.

Heterogeneous photocatalytic oxidation for the removal of organophosphorus pollutants from aqueous solutions: A review

Organophosphorus pollutants (OPs), which are compounds containing carbon‑phosphorus bonds or phosphate derivatives containing organic groups, have received much attention from researchers because of their persistence in the aqueous environment for long periods of time and the threat they pose to human health. Heterogeneous photocatalysis has been widely applied to the removal of OPs from aqueous solutions due to its better removal effect and environmental friendliness. In this review, the removal of OPs from aqueous matrices by heterogeneous photocatalysis was presented. Herein, the application and the heterogeneous photocatalysis mechanism of OPs were described in detail, and the effects of catalyst types on degradation effect are discussed categorically. In particular, the heterojunction type photocatalyst has the most excellent effect. After that, the photocatalytic degradation pathways of several OPs were summarized, focusing on the organophosphorus pesticides and organophosphorus flame retardants, such as methyl parathion, dichlorvos, dimethoate and chlorpyrifos. The toxicity changes during degradation were evaluated, indicating that the photocatalytic process could effectively reduce the toxicity of OPs. Additionally, the effects of common water matrices on heterogeneous photocatalytic degradation of OPs were also presented. Finally, the challenges and perspectives of heterogeneous photocatalysis removal of OPs are summarized and presented.

CuO/ZnO/CQDs@PAN Nanocomposites with Ternary Heterostructures for Enhancing Photocatalytic Performance

Photocatalysis is a green technology. In this paper, CuO/ZnO/carbon quantum dots (CQDs)@PAN nanocomposites with ternary heterostructures (CZC@PAN)—as high-performance environmentally friendly nanophotocatalysts—were prepared by electrospinning, heat treatment, and hydrothermal synthesis in sequence, and their practical applications were investigated by degrading methylene blue (MB). The synergistic effects of components in ternary heterostructures on the morphology, structure, and photocatalytic performance of CZC@PAN were analyzed, and their photocatalytic mechanism was further discussed. The results showed that due to the formation of p-n heterojunctions and the loading of CQDs and CZC@PAN had excellent photocatalytic degradation performance, and its photocatalytic degradation rate for MB reached 99.56% under natural sunlight for 4 h.

Antifouling CuO@TiO2 coating on plasma-grafted PAA/PES membrane based on photocatalysis and hydrogen peroxide activation

Because of the small size effect leading to the high bandgap of TiO₂ P25, the photocatalytic membrane using this photocatalyst has low antifouling efficiency. This study prepared CuO@TiO₂ composite photocatalyst with a lower bandgap than TiO₂ P25 and used it as antifouling coatings on the PES membrane with PAA intermediate adhesive layer. PAA was grafted onto the surface of the PES membranes through free radicals generated by the cold plasma treatment of the PES membrane. The composite photocatalysts were characterized by FTIR, SEM-EDS, TEM-EDS, XRD, BET, UV-Vis DRS, XPS, and ESR methods demonstrating high surface area (51.0 m²/g), decreased bandgap, and the formation of active free radicals under UV light irradiation. Under photocatalysis and hydrogen peroxide activation, the degradation of AB260 (acid blue 260) catalyzed by 10%CuO@TiO₂ reached about 92% after 60 min. Besides, the photocatalytic and antifouling activities of CuO@TiO₂/PAA/PES membranes are high and stable over five continuous cycles. The water flux of the modified membrane was not significantly influenced and only decreased about 10% compared to the pristine membrane. In addition, the flux recovery ratios (FRR) of fouled membranes treated by photocatalysis were almost 100%.

Photocatalytic Degradation of Tetracycline by Supramolecular Materials Constructed with Organic Cations and Silver Iodide

Photocatalytic degradation, as a very significant advanced oxidation technology in the field of environmental purification, has attracted extensive attention in recent years. The design and synthesis of catalysts with high-intensity photocatalytic properties have been the focus of many researchers in recent years. In this contribution, two new supramolecular materials {[(L1)·(Ag4I7)]CH3CN} (1), {[(L2)·(Ag4I7)]CH3CN} (2) were synthesized by solution volatilization reaction of two cationic templates 1,3,5-Tris(4-aminopyridinylmethyl)-2,4,6-Trimethylphenyl bromide (L1) and 1,3,5-Tris(4-methyl pyridinyl methyl)-2,4,6-trimethylphenyl bromide (L2) with metal salt AgI at room temperature, respectively. The degradation effect of 1 and 2 as catalyst on tetracycline (TC) under visible light irradiation was studied. The results showed that the degradation of TC by 1 was better than that by 2 and both of them had good stability and cyclability. The effects of pH value, catalyst dosage, and anion in water on the photocatalytic performance were also investigated. The adsorption kinetics fit the quasi-first-order model best. After 180 min of irradiation with 1, the degradation rate of TC can reach 97.91%. In addition, the trapping experiments showed that ·OH was the main active substance in the photocatalytic degradation of TC compared with ·O2− and h+. Because of its simple synthesis and high removal efficiency, catalyst 1 has potential value for the treatment of wastewater containing organic matter.

Analytical Review on Membrane Water Filter using Different Materials to Prevent Microbial Activities

Drinking water quality monitoring technologies have made significant progress in monitoring water resources and water treatment plants. This paper discusses the adverse effect of microbial contamination and also gives a brief description of the important parameters for drinking water and the technologies currently available used in this field. This paper is focused on studying the requirement for the development of low-cost filter materials that can be suitable as well as economical to be produced on a large-scale for real applications. There are several parameters such as porosity, contact angle, water flux, thickness, microbial activity needed to be focused on in the future to study the transformation of the hydrophilic property on the surface of the water.

A Brief Review of Photocatalytic Reactors Used for Persistent Pesticides Degradation

Pesticide pollution is a major issue, given their intensive use in the 20th century, which led to their accumulation in the environment. At the international level, strict regulations are imposed on the use of pesticides, simultaneously with the increasing interest of researchers from all over the world to find methods of neutralizing them. Photocatalytic degradation is an intensively studied method to be applied for the degradation of pesticides, especially through the use of solar energy. The mechanisms of photocatalysis are studied and implemented in pilot and semi-pilot installations on experimental platforms, in order to be able to make this method more efficient and to identify the equipment that can achieve the photodegradation of pesticides with the highest possible yields. This paper proposes a brief review of the impact of pesticides on the environment and some techniques for their degradation, with the main emphasis on different photoreactor configurations, using slurry or immobilized photocatalysts. This review highlights the efforts of researchers to harmonize the main elements of photocatalysis: choice of the photocatalyst, and the way of photocatalyst integration within photoreaction configuration, in order to make the transfer of momentum, mass, and energy as efficient as possible for optimal excitation of the photocatalyst.

Surfactant-Modified CdS/CdCO3 Composite Photocatalyst Morphology Enhances Visible-Light-Driven Cr(VI) Reduction Performance

The surfactant modification of catalyst morphology is considered as an effective method to improve photocatalytic performance. In this work, the visible-light-driven composite photocatalyst was obtained by growing CdS nanoparticles in the cubic crystal structure of CdCO₃, which, after surfactant modification, led to the formation of CdCO₃ elliptical spheres. This reasonable composite-structure-modification design effectively increased the specific surface area, fully exposing the catalytic-activity check point. Cd²⁺ from CdCO₃ can enter the CdS crystal structure to generate lattice distortion and form hole traps, which productively promoted the separation and transfer of CdS photogenerated electron-hole pairs. The prepared 5-CdS/CdCO₃@SDS exhibited excellent Cr(VI) photocatalytic activity with a reduction efficiency of 86.9% within 30 min, and the reduction rate was 0.0675 min^-1, which was 15.57 and 14.46 times that of CdS and CdCO₃, respectively. Finally, the main active substances during the reduction process, the photogenerated charge transfer pathways related to heterojunctions and the catalytic mechanism were proposed and analyzed.

Study on visible light photocatalytic performance of BiVO4 modified by graphene analogue boron nitride

In this study, a variety of boron nitride (BN) modified BiVO₄ (BN-BiVO₄) composites with visible-light response were prepared and used to degrade tetracyclines (TCs), including tetracycline (TC) and oxytetracycline (OTC). When treating the TCs solution under visible light irradiation, 4BN-BiVO₄ displayed high photocatalytic performance (87.1% for TC and 86.2% for OTC), which were 3.6 and 2.3 times than that of BiVO₄, respectively. Photoluminescence spectroscopy (PL) and transient photocurrent proved that the combination of BN and BiVO₄ effectively promotes the efficient separation of photogenerated electrons and holes in the material, resulting in enhanced photocatalytic activity. Further, radical trapping experiments in combination with electron spin resonance (ESR) revealed that ·OH radicals and holes were the predominant reactive species. Ultimately, the possible photocatalytic mechanism for TCs degradation was proposed on the basis of the experiments and characterization analysis. This study offers a new promising approach for the design of photocatalysts with visible-light response for efficient TCs elimination.

Insulator polymers achieve efficient catalysis under visible light due to contact electrification

Under the limitation of the carrier yield and mobility of semiconductor photocatalysts and the reaction domain, it seems that the photocatalytic efficiency cannot be greatly improved. Here, an efficient contact-electro-catalysis (CEC) system based on droplet triboelectric nanogenerator (TENG) is developed. Instead of using traditional semiconductor catalysts, the electric charge transferred during the electrification process of the contact between water droplets and polytetrafluoroethylene (PTFE) is used to participate in catalysis, and the output electrical signal can also monitor the degree of catalysis. The important role of light in the circulation of this CEC system is studied and discussed for the first time. It is proved that the contact electrification at the liquid-solid interface is accompanied by the generation of a large number of strong oxidizing radicals. The efficient transport of charge carriers driven by mechanical force and the active oxygen species distributed in the whole domain greatly improve the degradation rate of dyes. The experimental data show that the degradation efficiency of crystal violet (CV) reaches 90% within 38 s, and the rate constant k is as high as 3.7 min^-1. This is a breakthrough in the field of catalysis.

Engineered inverse opal structured semiconductors for solar light-driven environmental catalysis

Inverse opal (IO) macroporous semiconductor materials with unique physicochemical advantages have been widely used in solar-related environmental areas. In this minireview, we first summarize the synthetic methods of IO materials, emphasizing the two-step and three-step approaches, with the typical physicochemical properties being compared where applicable. We subsequently discuss the application of IO semiconductors (e.g., TiO₂, ZnO, g-C₃N₄) in various photo-related environmental techniques, including photo- and photoelectro-catalytic organic pollutant degradation in water, optical sensors for environmental monitoring, and water disinfection. The engineering strategies of these hierarchical structures for optimizing the activities for different catalytic reactions are discussed, ranging from heterojunction construction, cocatalyst loading, and heteroatom doping, to surface defect construction. Structure-activity relationships are established correspondingly. With a systematic understanding of the unique properties and catalytic activities, this review is expected to orient the design and structure optimization of IO semiconductor materials for photo-related performance improvement in various environmental techniques. Finally, the challenges of emerging IO structured semiconductors and future development directions are proposed.

Synthesis and applicability of reduced graphene oxide/porphyrin nanocomposite as photocatalyst for waste water treatment and medical applications

This study presents the synthesis and doping of reduced graphene oxide (rGO) with synthesized porphyrin (5,15-bisdodecyl porphyrin, C12P) nanoparticles to fabricate reduced graphene oxide-porphyrin (rGO-P) nanocomposite as well as demonstrates their outstanding removal activity of azo dye and antimicrobial potential. The synthesized porphyrin, rGO, and rGO-P nanocomposites were characterised using SEM, HRTEM, Raman spectroscopy, XRD, ¹H-NMR, mass spectrometry, and UV-Visible spectroscopy. The ability of the synthesized rGO-P nanocomposite was then investigated (as catalyst and/or adsorbent) to impact its removal efficacy against Congo red (CR) as a well-known toxic, mutagenic and carcinogenic synthetic dye. The findings indicated that 0.01 g of rGO-P nanocomposite achieved 78.0% removal of CR at pH 3.0. Besides, the removal efficacy was evaluated while studying many aspects i.e. pH, CR initial concentration, and rGO-P nanocomposite amount. Moreover, the minimum inhibitory concentration (MIC) and zone of inhibition (ZOI) of antimicrobial activity against pathogenic bacteria and yeast were evaluated. The antimicrobial results showed that rGO-P nanocomposite revealed the greatest antimicrobial activity against Candida albicans, Enterococcus faecalis, and Staphylococcus aureus with ZOI values of 24.3, 21.8, and 22.1 mm, respectively. Consequently, it demonstrates the substantial potential of rGO-P nanocomposite in the effective removal of pollutant dyes as well as significant antibacterial and antifungal properties.