Green preparation of activated carbon from pomegranate peel coated with zero-valent iron nanoparticles (nZVI) and isotherm and kinetic studies of amoxicillin removal in water

Removal of Cr(III) from Aqueous Solution Using Labeo rohita Chitosan-Based Composite

This study focusses on the synthesis of chitosan-cellulose composite membrane derived from Labeo rohita fish scales (FS) for the removal of Cr(III) from aqueous solution, while chromium is a serious threat to groundwater. Waste FS are valorized to chitosan by demineralization, deproteination, and deacetylation successively. Cellulose was extracted from sugarcane bagasse using acidic hydrolysis. Chitosan-based cellulose composite porous membrane was fabricated by evaporating solvent from polymer solution in petri dish. The impact of pH, contact time, and absorbent dosage on the removal of Cr(III) from an aqueous solution was investigated. Atomic absorption spectrophotometer was used to check the Cr(III). Results showed that chitosan comprising 85% degree of deacetylation was achieved by alkali treatment, while yield was 22%. FTIR analysis confirmed the chitosan and chitosan-cellulose-based composite membrane. Morphology studies showed that the cellulose was strongly staggered and due to the chitosan, the surface of cellulose became rougher, which is good to enhance the adsorption capacity. The maximum removal 57% of Cr(III) from aqueous solution was observed at pH 6 at 60 min and 50 mg dosage of adsorbent. The minimum removal (47%) of Cr (III) was found at pH 2. These results confer that Labeo rohita-based chitosan-cellulose composite membrane has great potential for the removal of metals from industrial effluents.

Removal of Amoxicillin from Aqueous Media by Fenton-like Sonolysis/H2O2 Process Using Zero-Valent Iron Nanoparticles

High concentrations of antibiotics have been identified in aqueous media, which has diminished the quality of water resources. These compounds are usually highly toxic and have low biodegradability, and there have been reports about their mutagenic or carcinogenic effects. The aim of this study was to apply zero-valent iron-oxide nanoparticles in the presence of hydrogen peroxide and the sonolysis process for the removal of the amoxicillin antibiotic from aqueous media. In this study, zero-valent iron nanoparticles were prepared by an iron chloride reduction method in the presence of sodium borohydride (NaBH4), and the obtained nanoparticles were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and vibrating-sample magnetometry (VSM). Then, using a Fenton-like process, synthetic wastewater containing 100 to 500 mg/L amoxicillin antibiotic was investigated, and the effects of different parameters, such as the frequency (1 and 2 kHz), contact time (15 to 120 min), the concentration of hydrogen peroxide (0.3%, 0.5%, and 6%), the dose of zero-valent iron nanoparticles (0.05, 0.1, 0.5 g/L), and pH (3, 5, 10) were thoroughly studied. A pH of 3, hydrogen peroxide concentration of 3%, ultrasonic-wave frequency of 130 kHz, zero-valent iron nanoparticles of 0.5 g/L, and contaminant concentration of 100 mg/L were obtained as the optimal conditions of the combined US/H2O2/nZVI process. Under the optimal conditions of the combined process of zero-valent iron nanoparticles and hydrogen peroxide in the presence of ultrasonic waves, a 99.7% removal efficiency of amoxicillin was achieved in 120 min. The results show that the combined US/H2O2/nZVI process could be successfully used to remove environmental contaminants, including antibiotics such as amoxicillin, with a high removal percentage.

Simple preparation of a CuO@γ-Al2O3 Fenton-like catalyst and its photocatalytic degradation function

We designed a photocatalyst and developed sustainable wastewater purification technology, which have significant advantages in effectively solving the global problem of drinking water shortage. In this study, a new nanocomposite was reported and shown to be a catalyst with excellent performance; CuO was coated successively onto functionalized nano γ-Al₂O₃, and this novel structure could provide abundant active sites. We evaluated the performance of the CuO@γ-Al₂O₃ nanocomposite catalyst for polyvinyl alcohol (PVA) degradation under visible light irradiation. Under optimized conditions (calcination temperature, 450 °C; mass ratio of γ-Al₂O₃:Cu(NO₃)₂·3H₂O, 1:15; pH value, 7; catalyst dosage, 2.6 g/L; reaction temperature, 20 °C; and H₂O₂ dosage, 0.2 g/mL), the CuO@γ-Al₂O₃ nanocomposite catalyst presented an excellent PVA removal rate of 99.21%. After ten consecutive degradation experiments, the catalyst could still maintain a PVA removal rate of 97.58%, thus demonstrating excellent reusability. This study provides an efficient and easy-to-prepare photocatalyst and proposes a mechanism for the synergistic effect of the photocatalytic reaction and the Fenton-like reaction.

Efficient adsorption of Pb(II) by sodium dodecyl benzene sulfonate intercalated calcium aluminum hydrotalcites: kinetic, isotherm, and mechanisms

Two novel adsorbents of CaAl-LDHs and sodium dodecyl benzene sulfonate (SDBS) intercalated CaAl-LDHs (SDBS-CaAl-LDHs) were successfully prepared by co-precipitation. The main composition and physical properties of two samples were characterized by XRD, XPS, FT-IR, TG, and SEM. Batch adsorption experiments were conducted to study the effect of pH, adsorption time, and initial concentration of Pb²⁺. The results showed that the prime adsorption conditions obtained were pH of 5.2 after 60 min with the initial concentration of 300 mg g^-1 for CaAl-LDHs and 350 mg g^-1 for SDBS-CaAl-LDHs. At 303 K, the adsorption capacities and removal rates of CaAl-LDHs and SDBS-CaAl-LDHs were found to be 456.05 mg g^-1, 91.21% and 682.26 mg g^-1, 97.47%, respectively. For CaAl-LDHs, the kinetic data for Pb²⁺ was best fitted with pseudo-2nd-order model, and the adsorption isotherms followed Langmuir and Freundlich isotherm model. The adsorption data of SDBS-CaAl-LDHs can be best described by the pseudo-second-order kinetic and Langmuir model. The Pb²⁺ adsorption mechanism on SDBS-CaAl-LDHs was explored by XRD, XPS, and SEM, and the important roles of the electrostatic attraction, precipitation, complexation, and ion exchange were demonstrated. The Langmuir adsorption capacities for SDBS-CaAl-LDHs were 797.63, 828.76, and 854.29 mg g^-1 at 293 k, 303 k, and 313 k, respectively. Thus, SDBS-CaAl-LDHs may be a highly economical adsorbent for the treatment of contaminated water.

Kinetics, isotherms and thermodynamics of oil spills removal by novel amphiphilic Chitosan-g-Octanal Schiff base polymer developed by click grafting technique

Kinetic, isothermal and thermodynamic studies for the oil spills removal process have been conducted by Chitosan and novel amphiphilic Chitosan-g-Octanal Schiff base adsorbents developed by click chemistry and evaluated successfully in the removal of heavy crude oil spills. Chitosan was first prepared from wastes of marine shrimp shells, and then Chitosan and Chitosan-g-Octanal Schiff base adsorbents were synthesized and verified their structures, thermal stability and their morphological changes using FT-IR spectroscopy, TGA and SEM. The oil adsorption percentages (%) using heavy crude oil were 96.41% for the Chitosan-g-Octanal Schiff base adsorbent compared to 64.99% for native Chitosan counterpart. High rate of adsorption was observed where 40% of oil adsorbed within 15 min only using the Chitosan-g-Octanal Schiff base adsorbent compared to 90 min for native Chitosan adsorbent. The adsorption process followed the pseudo-second order model, and the equilibrium data were sufficiently fitted with the Langmuir model with a maximum adsorption capacity 30.30 g/g at 25 °C. Thermodynamic parameters computed from Van’t Hoff plot confirmed the process to be endothermic, favorable and spontaneous.

Adsorptive Behavior of Tartaric Acid Treated Holarrhena antidysenterica and Citrullus colocynthis Biowastes for Decolourization of Congo Red Dye from Aqueous Solutions

The aim of the present work is to eradicate Congo red (CR) dye from aqueous solutions since the dye compounds are harmful to human life and the environment leading to detrimental results. For this purpose, Holarrhena antidysenterica (HA) and Citrullus colocynthis (CC) adsorbents were used for the adsorptive removal of Congo red dye from wastewaters. The unmodified adsorbents (U-HA and U-CC) were chemically modified using tartaric acid (TA). Morphological structures were examined by FTIR and SEM. Batch adsorption studies were tested at a variety of pH, time exposure, temperatures, and adsorbent dosages. Thermodynamic parameters such as Gibbs free energy ( $∆G^{°}$ ), enthalpy ( $∆H^{°}$ ), entropy changes ( $∆S^{°}$ ), and energy of activation ( $E_{\text{a}}$ ) were also calculated. The results revealed that tartaric acid-Citrullus colocynthis (TA-CC) gave optimum conditions of time of contact (35 min), temperature conditions (40°C), pH (3), and dosage of adsorbent (1.6 g) for maximum dye removal. Tartaric acid-Holarrhena antidysenterica (TA-HA) gave equilibrium time of contact (30 min), temperature (40°C), and pH optimum (2) along with a 1.6 g dosage of adsorbent. Mechanistic understanding of adsorption isotherm provided that the Langmuir model was followed by raw and modified adsorbents. Maximum adsorption capacities $Q_{\max }$ attained were 60.61 (mg g-1), 128.21 (mg g-1), 87.71 (mg g-1), and 131.57 (mg g-1), respectively, for U-HA, TA-HA, U-CC, and TA-CC. The results of kinetic modeling displayed a high value of $R^2$ (0.99) along with minimal error (RMSE) for dye removal showing that the pseudo-second-order kinetic model has acceptable accuracy. Fourier transform infrared proposed the electrostatic, pi-pi interactions, and hydrogen bonding as dominant adsorption mechanisms at acidic pH, respectively. Rate-determining steps comprise both surface and intraparticle diffusions. Thermodynamics indicated that the dye adsorption of CR is spontaneous, exothermic, and favorable in nature. These agricultural wastes due to specific points such as low cost, availability, and high removal rates of adsorption are highly competent for the expulsion of anionic dye like CR from wastewaters.

Optimizing the Extraction Conditions of Hydroxytyrosol from Olive Leaves Using a Modified Spherical Activated Carbon: A New Experimental Design

The purification of hydroxytyrosol from olive leaves extract by modified activated carbon was studied experimentally in a batch system and a column by adsorption and desorption processes. The extraction yield reached 90% of hydroxytyrosol, which is the major compound found in the extract. Despite the abundance of research on extracts of hydroxytyrosol from olive leaves, it seems that the applied methods can be further improved. In this study, several approaches were applied to optimize the extraction conditions of this molecule. Hence, the response surface method and the Box-Behnken design (BBD) were used to evaluate the effect of the temperature, time, and adsorbent dose on the hydroxytyrosol recovery. Moreover, adsorption isotherm, kinetics, and thermodynamic studies were also performed to clarify the nature of the process. The main finding was the obtainment of a maximum adsorption yield of 97.5% at an adsorbent/adsorbate ratio of 1 : 20, after a 6 h cycle and at a temperature of 30°C. Furthermore, adsorption process seemed to fit best with Freundlich model. In addition, the thermodynamic study describes a spontaneous and endothermic process. Desorption assay using ethanol helped to recover 73% of hydroxytyrosol. Furthermore, the HPLC analysis of fractions after column adsorption showed a simple peak of hydroxytyrosol with purity higher than 97% and a flavonoids-rich fraction. These findings would indicate that this separation method for the recovery of phenolic compounds with high antioxidant activity can be a very promising one.

The Application of Response Surface Methodology for 2,4,6-Trichlorophenol Removal from Aqueous Solution Using Synthesized Zn2+-Al3+-Tartrate Layered Double Hydroxides

Trichlorophenols are on the US environmental protection agency’s list of priority pollutants due to their serious damage to water safety. With the aim of adsorbing the 2,4,6-trichlorophenol (2,4,6-TCP), Zn2+-Al3+-tartrate layered double hydroxides (Zn2+-Al3+-C4H4O62−-LDHs) adsorbent was synthesized via homogeneous precipitation method. X-ray powder diffraction (XRD), Fourier infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) were used to characterize Zn2+-Al3+-C4H4O62−-LDHs. The concentration of 2,4,6-TCP was determined using gas chromatography–mass spectrometry (GC-MS). Zn2+-Al3+-C4H4O62−-LDHs exhibited a good adsorption performance of 2,4,6-trichlorophenol, since a bigger layer spacing of Zn2+-Al3+-C4H4O62−-LDHs was obtained than that in Zn2+-Al3+-CO32−-LDHs. Adsorption parameters of adsorption temperature, contact time, adsorbent dosage, and solution pH were investigated, the initial concentration of 2,4,6-TCP was 2.0 g/L. Response surface methodology (RSM) was employed to provide an investigative approach towards optimization of the adsorption process. The highest removal rate of 89.94% and the average removal rate of 88.74% were achieved under a temperature of 20.0 °C, a contact time of 2.5 h, an adsorbent dosage of 0.15 g, and a solution pH of 3. the capacity of the adsorbent is 599.6 mg/g. Meanwhile, the reusable properties of Zn2+-Al3+-C4H4O62−-LDHs were evaluated by the same adsorption system, and the removal rate of 2,4,6-TCP was 85.57% at the fifth regeneration. The obtained results confirmed that the Zn2+-Al3+-C4H4O62−-LDHs can be used as a potential introduction in practical applications for the removal of 2,4,6-TCP.

Green synthesis of zinc oxide nanoparticles loaded on activated carbon prepared from walnut peel extract for the removal of Eosin Y and Erythrosine B dyes from aqueous solution: experimental approaches, kinetics models, and thermodynamic studies

Water contamination due to release of dye containing effluents is one of the environmental problems of serious concern today. The present study investigate the green synthesis of zinc oxide nanoparticles (ZnO-NPs) doped on activated carbon (AC) prepared from walnut peel extract and to estimate its efficiency in the removal of Eosin Y (Eo-Y) and Erythrosine B (Er-B) from its aqueous solution. The synthesized AC-ZnO was identified by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), and the Brunauer-Emmett-Teller. The influence of various parameters such as pH, dosage of AC-ZnO, contact time, and concentrations of Eo-Y and Er-B was also studied. The pH 3 was observed as the optimum pH while the equilibrium was noticed to reach in 30 min at dosage of 1 g/L and initial concentration 100 mg/L for Eo-Y and Er-B adsorption onto AC-ZnO. The maximum adsorption capacity of Eo-Y and Er-B onto AC-ZnO was found to be 163.9 and 144.92 mg/g (and removal efficiencies of 95.11 and 98.31 %), respectively. The process of Eo-Y and Er-B adsorption on AC-ZnO was observed to be depended on the pseudo-second-order kinetic model which indicates chemisorption processes. Langmuir adsorption isotherm model test described the removal of Eo-Y and Er-B on AC-ZnO. The thermodynamic data indicated that the adsorption was endothermic process. Also, the values, S_BET and V_TOTAL, for the AC-ZnO were equal to 725.65 m²/g and 0.6004 cm³/g, respectively. The results of this study exhibited that AC-ZnO was a very effective method that can be used for the removal of Eo-Y and Er-B from aqueous solutions.

Green Synthesis of Nano-Zero-Valent Iron Using Ricinus Communis Seeds Extract: Characterization and Application in the Treatment of Methylene Blue-Polluted Water

In this study, the removal of methylene blue dye (MB) from aqueous solution was examined using a novel green adsorbent to overcome the obstacles encountered in chemical methods. Ricinus communis (RC) aqueous seeds extract was herein used as a reducing and capping agent to synthesize a novel nano-zero-valent iron (RC-nZVI) for the adsorption of harmful MB. Structural and morphological characterization of the synthesized RC-nZVI were performed using several techniques, e.g., steady-state absorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and zeta potential. The maximum efficiency of the removal was 96.8% at pH 6 and 25 °C. According to the kinetics study results, the adsorption process obeys the pseudo-first-order model. The experimental equilibrium data were fitted to the Freundlich isotherm model, the maximum adsorption capacity reached was 61.37 mg·g-1, and the equilibrium parameters were determined. The synthesized RC-nZVI possesses good reusability and can be considered as a potential economic and environmentally friendly adsorbent.

Using Pomegranate Peel and Date Pit Activated Carbon for the Removal of Cadmium and Lead Ions from Aqueous Solution

Some agricultural byproducts are useful for solving wastewater pollution problems. These byproducts are of low cost and are effective and ecofriendly. The study aim was to investigate the possibility of using pomegranate peel (PP) and date pit (DP) activated carbon (PPAC and DPAC, respectively) as sorbents to remove Cd(II) and Pb(II) from aqueous solutions. Agricultural wastes of DPs and PPs were subjected to carbonization and chemical activation with H3PO4 (60%) and ZnCl2 and used as adsorbents to remove Cd(II) and Pb(II) from their aqueous solutions. The physical characterizations of PPAC and DPAC, including determination of surface area, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy, were performed. The following factors affected adsorption: solution pH, adsorbent dosage, initial metal ion concentration, and contact time. These factors were studied to identify the optimal adsorption conditions. The results showed that the maximum adsorptions of Cd(II) and Pb(II) were achieved at pH ranging from 6 to 6.5, 90 min contact time, and 0.5 g/L for PPAC and 1 g/L for DPAC dosage. Furthermore, the adsorption efficiencies for both Pb(II) and Cd(II) were higher for PPAC than for DPAC. However, the recorded Qmax values for PPAC were 68.6 and 53.8 mg/g for Pb(II) and Cd(II) and for DPAC were 34.18 and 32.90 mg/g for Pb(II) and Cd(II), respectively. The Langmuir isotherm model fit the adsorption data better than the Freundlich model. Kinetically, the adsorption reaction followed a pseudo-second-order reaction model, with qe ranging from 12.0 to 22.37 mg/g and an R2 value of 0.99.

Water Purification of Classical and Emerging Organic Pollutants: An Extensive Review

The main techniques used for organic pollutant removal from water are adsorption, reductive and oxidative processes, phytoremediation, bioremediation, separation by membranes and liquid–liquid extraction. In this review, strengths and weaknesses of the different purification techniques are discussed, with particular attention to the newest results published in the scientific literature. This study highlighted that adsorption is the most frequently used method for water purification, since it can balance high organic pollutants removal efficiency, it has the possibility to treat a large quantity of water in semi-continuous way and has acceptable costs.

Mesoporous Biopolymer Architecture Enhanced the Adsorption and Selectivity of Aqueous Heavy-Metal Ions

Halloysite nanotubes (HNT) and ball-milled biochar (BC) incorporated biocompatible mesoporous adsorbents (HNT-BC@Alg) were synthesized for adsorption of aqueous heavy-metal ions. HNT-BC@Alg outperformed the BC, HNT, and BC@Alg in removing cadmium (Cd), copper (Cu), nickel (Ni), and lead (Pb). Mesoporous structure (∼7.19 to 7.56 nm) of HNT-BC@Alg was developed containing an abundance of functional groups induced from encapsulated BC and tubular HNT, which allowed heavy metals to infiltrate and interact with the adsorbents. Siloxane groups from HNT, oxygen-containing functional groups from BC, and hydroxyl and carboxyl groups from alginate polymer play a significant role in the adsorption of heavy-metal ions. The removal percentage of heavy metals was recorded as Pb (∼99.97 to 99.05%) > Cu (∼95.01 to 90.53%) > Cd (∼92.5 to 55.25%) > Ni (∼80.85 to 50.6%), even in the presence of 0.01/0.001 M of CaCl₂ and Na₂SO₄ as background electrolytes and charged organic molecule under an environmentally relevant concentration (200 μg/L). The maximum adsorption capacities of Ni, Cd, Cu, and Pb were calculated as 2.85 ± 0.08, 6.96 ± 0.31, 16.87 ± 1.50, and 26.49 ± 2.04 mg/g, respectively. HNT-BC@Alg has fast sorption kinetics and maximum adsorption capacity within a short contact time (∼2 h). Energy-dispersive X-ray spectroscopy (EDS) elemental mapping exhibited that adsorbed heavy metals co-distributed with Ca, Si, and Al. The reduction of surface area, pore volume, and pore area of HNT-BC@Alg (after sorption of heavy metals) confirms that mesoporous surface (2-18 nm) supports diffusion, infiltration, and interaction. However, a lower range of mesoporous diameter of the adsorbent is more suitable for the adsorption of heavy-metal ions. The adsorption isotherm and kinetics fitted well with the Langmuir isotherm and the pseudo-second-order kinetic models, demonstrating the monolayer formation of heavy-metal ions through both the physical sorption and chemical sorption, including pore filling, ion exchange, and electrostatic interaction.