Bone tissue engineering techniques, advances and scaffolds for treatment of bone defects

Three-Dimensional Printing of Poly-L-Lactic Acid Composite Scaffolds with Enhanced Bioactivity and Controllable Zn Ion Release Capability by Coupling with Carbon-ZnO

Poly-L-lactic acid (PLLA) has gained great popularity with researchers in regenerative medicine owing to its superior biocompatibility and biodegradability, although its inadequate bioactivity inhibits the further use of PLLA in the field of bone regeneration. Zinc oxide (ZnO) has been utilized to improve the biological performance of biopolymers because of its renowned osteogenic activity. However, ZnO nanoparticles tend to agglomerate in the polymer matrix due to high surface energy, which would lead to the burst release of the Zn ion and, thus, cytotoxicity. In this study, to address this problem, carbon–ZnO (C–ZnO) was first synthesized through the carbonization of ZIF-8. Then, C–ZnO was introduced to PLLA powder before it was manufactured as scaffolds (PLLA/C–ZnO) by a selective laser sintering 3D printing technique. The results showed that the PLLA/C–ZnO scaffold was able to continuously release Zn ions in a reasonable range, which can be attributed to the interaction of Zn–N bonding and the shielding action of the PLLA scaffold. The controlled release of Zn ions from the scaffold further facilitated cell adhesion and proliferation and improved the osteogenic differentiation ability at the same time. In addition, C–ZnO endowed the scaffold with favorable photodynamic antibacterial ability, which was manifested by an efficient antibacterial rate of over 95%.

Development of Scaffolds from Bio-Based Natural Materials for Tissue Regeneration Applications: A Review

Tissue damage and organ failure are major problems that many people face worldwide. Most of them benefit from treatment related to modern technology's tissue regeneration process. Tissue engineering is one of the booming fields widely used to replace damaged tissue. Scaffold is a base material in which cells and growth factors are embedded to construct a substitute tissue. Various materials have been used to develop scaffolds. Bio-based natural materials are biocompatible, safe, and do not release toxic compounds during biodegradation. Therefore, it is highly recommendable to fabricate scaffolds using such materials. To date, there have been no singular materials that fulfill all the features of the scaffold. Hence, combining two or more materials is encouraged to obtain the desired characteristics. To design a reliable scaffold by combining different materials, there is a need to choose a good fabrication technique. In this review article, the bio-based natural materials and fine fabrication techniques that are currently used in developing scaffolds for tissue regeneration applications, along with the number of articles published on each material, are briefly discussed. It is envisaged to gain explicit knowledge of developing scaffolds from bio-based natural materials for tissue regeneration applications.

[Development of osteoplastic gene-activated 3D matrices based on adenoviral vectors]

Gene therapy is one of the most promising approaches in regenerative medicine for the restoration of extensive bone defects in dentistry and maxillofacial surgery. Matrices obtained using three-dimensional printing from bioresorbable polymers, impregnated with adenoviral constructs with genes for osteoinductive factors, can ensure safe and effective formation of bone tissue.

OBJECTIVE

To study the properties of three-dimensional matrices based on polylactic-co-glycolic acid and adenoviral constructs with the GFP gene in vitro.

MATERIALS AND METHODS

The matrices were obtained by antisolvent three-dimensional printing. Transduction efficiency was assessed by fluorescence microscopy and flow cytometry. The cytocompatibility of the matrices was assessed by the MTT test and by staining cells with fluorescent dyes.

RESULTS

Matrices based on polylactic-co-glycolic acid have high cytocompatibility on adipose tissue-derived mesenchymal stem cells. Impregnation of adenoviral vectors with the green fluorescent protein gene in 3D matrices ensures the release of viral particles within a week, maintaining their high transducing ability.

CONCLUSION

The developed method for obtaining gene-activated matrices can serve as the basis for the creation of effective osteoplastic materials for bone regeneration.

Management of bone diseases: looking at scaffold-based strategies for drug delivery

The bone tissue can regenerate itself completely and continuously; however, large-scale bone defects may overpower this self-regenerative process. Furthermore, the aging population, the increment in obesity incidence, and the sedentary lifestyles are serious risk factors for bone diseases' development which are associated with the self-regenerative process's failure, high morbidity, and mortality rates. Thus, there is an ever-growing need for strategic approaches targeting bone replacement, its remodelling, and its regeneration. Bone scaffolds have successfully been used as synthetic bone grafts for many years, yet recent bone tissue engineering strategies attempt to explore their multifunctionality by investigating them as drug delivery systems. Bone diseases' treatments can be substantially difficult due to the avascular nature of the surrounding cartilage; thus, targeted drug delivery to the bone can be advantageous: it provides local high drug concentrations and minimizes adverse effects while securing a space for new, healthy tissue growth. Despite the promising scientific progress, studies underlining bone scaffolds' use as local drug delivery systems are not abundant. Hence, this work reviews bone scaffolds' therapeutic interest for local drug delivery in five distinct bone disorders-osteomyelitis, osteoporosis, osteoarthritis, osteosarcoma, and cancer bone metastasis. Additionally, it presents the challenges of this possible therapeutic approach and its future perspectives. Albeit bone scaffolds present therapeutic benefits by acting as drug delivery systems, further pre-clinical and clinical assessments are needed to strengthen their understanding and enable research evidence translation into clinical practice. The mismatch between scientific evolution and regulatory frameworks remains one of the major future challenges.

About 3D Printability of Thermoplastic Collagen for Biomedical Applications

With more than 1.5 million total knee and hip implants placed each year, there is an urgent need for a drug delivery system that can effectively support the repair of bone infections. Scaffolds made of natural biopolymers are widely used for this purpose due to their biocompatibility, biodegradability, and suitable mechanical properties. However, the poor processability is a bottleneck, as highly customizable scaffolds are desired. The aim of the present research is to develop a scaffold made of thermoplastic collagen (TC) using 3D printing technology. The viscosity of the material was measured using a rheometer. A 3D bioplotter was used to fabricate the scaffolds out of TC. The mechanical properties of the TC scaffolds were performed using tension/compression testing on a Zwick/Roell universal testing machine. TC shows better compressibility with increasing temperature and a decrease in dynamic viscosity (η), storage modulus (G'), and loss modulus (G″). The compressive strength of the TC scaffolds was between 3-10 MPa, depending on the geometry (cylinder or cuboid, with different infills). We have demonstrated for the first time that TC can be used to fabricate porous scaffolds by 3D printing in various geometries.

Fabrication and biological evaluation of three-dimensional (3D) Mg substituted bi-phasic calcium phosphate porous scaffolds for hard tissue engineering

This work reports on the fabrication of three-dimensional (3D) magnesium substituted bi-phasic calcium phosphate (Mg-BCP) scaffolds by gel-casting, their structural and physico-chemical characterization, and on the assessment of their in vitro and in vivo performances. The crystalline phase assemblage, chemical functional groups and porous morphology features of the scaffolds were evaluated by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR) and field emission scanning electron microscopy (FE-SEM), respectively. The sintered scaffolds revealed an interconnected porosity with pore sizes ranging from 4.3 to 7.28 μm. The scaffolds exhibited good biomineralization activity upon immersion in simulated body fluid (SBF), while an in vitro study using MG-63 cell line cultures confirmed their improved biocompatibility, cell proliferation and bioactivity. Bone grafting of 3D scaffolds was performed in non-load bearing bone defects surgically created in tibia of rabbits, used as animal model. Histological and radiological observations indicated the successful restoration of bone defects. The overall results confirmed the suitability of the scaffolds to be further tested as synthetic bone grafts in bone regeneration surgeries and in bone tissue engineering applications.

Recent advances on small molecules in osteogenic differentiation of stem cells and the underlying signaling pathways

Bone-related diseases are major contributors to morbidity and mortality in elderly people and the current treatments result in insufficient healing and several complications. One of the promising areas of research for healing bone fractures and skeletal defects is regenerative medicine using stem cells. Differentiating stem cells using agents that shift cell development towards the preferred lineage requires activation of certain intracellular signaling pathways, many of which are known to induce osteogenesis during embryological stages. Imitating embryological bone formation through activation of these signaling pathways has been the focus of many osteogenic studies. Activation of osteogenic signaling can be done by using small molecules. Several of these agents, e.g., statins, metformin, adenosine, and dexamethasone have other clinical uses but have also shown osteogenic capacities. On the other hand, some other molecules such as T63 and tetrahydroquinolines are not as well recognized in the clinic. Osteogenic small molecules exert their effects through the activation of signaling pathways known to be related to osteogenesis. These pathways include more well-known pathways including BMP/Smad, Wnt, and Hedgehog as well as ancillary pathways including estrogen signaling and neuropeptide signaling. In this paper, we review the recent data on small molecule-mediated osteogenic differentiation, possible adjunctive agents with these molecules, and the signaling pathways through which each small molecule exerts its effects.

Enhancing physicochemical, mechanical, and bioactive performances of monetite nanoparticles reinforced chitosan‐PEO electrospun scaffold for bone tissue engineering

In the current work, monetite (DCPA) nanoparticles incorporated chitosan (CH)‐based composite was prepared using by electrospinning technique. A smooth and defect‐free fibrous matrix with an average fiber diameter in the range between 311 ± 13 to 380 ± 28 nm was obtained for 5 wt% (CH‐DCPA5) and 7 wt% DCPA (CH‐DCPA7) containing electrospun scaffolds. The results indicated that the addition of 7 wt% DCPA nanoparticles to chitosan caused an increase in the tensile strength of scaffolds from 6.2 to 12.34 MPa. A slow degradation rate (~37% in 28 days) indicates its suitability for bone tissue regeneration. A study on the biomineralization capability of the electrospun scaffolds after their immersion in simulated body fluid in vitro revealed that the addition of DCPA strongly promoted the deposition of the apatite layer onto electrospun nanofibrous scaffolds. The culture of MG‐63 osteoblast cells on the scaffolds demonstrated that the incorporation of DCPA nanoparticles into the chitosan polymeric matrix helped in the adhesion, spreading, and migration of cells. CH‐DCPA5 and CH‐DCPA7 scaffolds exhibited a higher capacity to proliferate osteoblast cell lines as compared to pure CH scaffold as confirmed by MTT assay and qualitative cell viability analysis from fluorescence microscopy. Immunocytochemistry analysis for osteocalcin expression revealed a higher capacity of DCPA‐containing scaffolds to differentiate MG‐63 cells into bone lineage as compared to pure chitosan scaffolds. DCPA incorporation into chitosan also resulted in MG‐63 cultured on to it to elicit higher alkaline phosphatase activity suggesting the highest capacity of CH‐DCPA7 to differentiate MG 63 cell line among all the scaffolds studied here. The results indicated superior osteogenic properties of DCPA nanoparticle reinforced chitosan matrix for use in BTE in the form of nanofibrous scaffolds.

FeMn with Phases of a Degradable Ag Alloy for Residue-Free and Adapted Bioresorbability

The development of bioresorbable materials for temporary implantation enables progress in medical technology. Iron (Fe)-based degradable materials are biocompatible and exhibit good mechanical properties, but their degradation rate is low. Aside from alloying with Manganese (Mn), the creation of phases with high electrochemical potential such as silver (Ag) phases to cause the anodic dissolution of FeMn is promising. However, to enable residue-free dissolution, the Ag needs to be modified. This concern is addressed, as FeMn modified with a degradable Ag-Calcium-Lanthanum (AgCaLa) alloy is investigated. The electrochemical properties and the degradation behavior are determined via a static immersion test. The local differences in electrochemical potential increase the degradation rate (low pH values), and the formation of gaps around the Ag phases (neutral pH values) demonstrates the benefit of the strategy. Nevertheless, the formation of corrosion-inhibiting layers avoids an increased degradation rate under a neutral pH value. The complete bioresorption of the material is possible since the phases of the degradable AgCaLa alloy dissolve after the FeMn matrix. Cell viability tests reveal biocompatibility, and the antibacterial activity of the degradation supernatant is observed. Thus, FeMn modified with degradable AgCaLa phases is promising as a bioresorbable material if corrosion-inhibiting layers can be diminished.

Novel Approaches and Biomaterials for Bone Tissue Engineering: A Focus on Silk Fibroin

Bone tissue engineering (BTE) represents a multidisciplinary research field involving many aspects of biology, engineering, material science, clinical medicine and genetics to create biological substitutes to promote bone regeneration. The definition of the most appropriate biomaterials and structures for BTE is still a challenge for researchers, aiming at simultaneously combining different features such as tissue generation properties, biocompatibility, porosity and mechanical strength. In this scenario, among the biomaterials for BTE, silk fibroin represents a valuable option for the development of functional devices because of its unique biological properties and the multiple chances of processing. This review article aims at providing the reader with a general overview of the most recent progresses in bone tissue engineering in terms of approaches and materials with a special focus on silk fibroin and the related mechanisms involved in bone regeneration, and presenting interesting results obtained by different research groups, which assessed the great potential of this protein for bone tissue engineering.

Enhanced In Vitro Biocompatible Polycaprolactone/Nano-Hydroxyapatite Scaffolds with Near-Field Direct-Writing Melt Electrospinning Technology

Polycaprolactone (PCL) scaffold is a common biological material for tissue engineering, owing to its good biocompatibility, biodegradability and plasticity. However, it is not suitable for osteoblast adhesion and regeneration of bone tissue due to its non-biological activity, poor mechanical strength, slow degradation speed, smooth surface and strong hydrophobicity. To improve the mechanical properties and biocompatibility of PCL scaffold, the PCL/nHA scaffolds were prepared by melting and blending different proportions of nano-hydroxyapatite (nHA) with PCL by the near-field direct-writing melt electrospinning technology in this study. The morphology, porosity, mechanical properties and in vitro biocompatibility of the PCL/nHA scaffolds were studied. The results showed that when the proportion of nHA was less than or equal to 25%, PCL/nHA composite scaffolds were easily formed in which bone marrow mesenchymal stem cells proliferated successfully. When the proportion of nHA was 15%, the PCL/nHA composite scaffolds had excellent structural regularity, good fiber uniformity, outstanding mechanical stability and superior biocompatibility. The PCL/nHA composite scaffolds were ideal scaffold materials, which would broaden their applications for bone tissue engineering.

Polycaprolactone/Gelatin/Hydroxyapatite Electrospun Nanomembrane Materials Incorporated with Different Proportions of Attapulgite Synergistically Promote Bone Formation

Purpose

To enhance the osteoinductive effect of Hydroxyapatite (HA) in bone tissue engineering, this study manufactured polycaprolactone (PCL)/gelatin (GEL)/HA nanofibrous scaffolds incorporated with different ratios of attapulgite (ATP): HA (0:3, 0:0, 1:1, 2:1 and 3:0) by high-voltage electrospinning. The synergistic effect exerted by ATP and HA on bone formation was explored both in vivo and in vitro.

Methods and Results

First, we determined the group composition and crystal structure of the nanosheets by Fourier transform infrared (FTIR) and X-ray diffraction (XRD) analyses. Then, the physical properties of the scaffolds, including the modulus of elasticity, porosity and water absorption were evaluated. Moreover, the surface microstructure of the nanofibrous scaffolds was captured by Scanning electron microscopy (SEM) and Transmission Electron Microscope (TEM). The biocompatibility of the fabricated scaffolds represented by cell counting kit 8 (CCK-8) and phalloidin staining was also assessed. Next, in vitro osteogenesis was evaluated. Real-time PCR, alkaline phosphatase (ALP) staining and Alizarin red S (ARS) staining results showed that the materials incorporated with HA and ATP at a ratio of 2:1 synergistically promoted more osteoblastic differentiation and extracellular mineralization than scaffolds doped with HA and ATP alone. Last, in vivo, Hematoxylin-Eosin staining (HE staining) and Masson staining showed that groups treated with HA and ATP acquired optimal patterns of bone regeneration.

Conclusion

This study clarified for the first time that the combination of HA and ATP orchestrated biomaterial-induced osseointegration, and the synergistic effect was more significant when the ratio of ATP/HA was 2:1. This conclusion also provides new ideas and a scientific basis for the development of functionalized nanomaterials in bone tissue engineering.

Influences of Process Parameters of Near-Field Direct-Writing Melt Electrospinning on Performances of Polycaprolactone/Nano-Hydroxyapatite Scaffolds

In this paper, near-field direct-writing melt electrospinning technology was employed to fabricate a polycaprolactone/nano-hydroxyapatite (PCL/nHA) scaffold for future applications in tissue engineering. The influences of different fabrication parameters on the structural characteristics, mechanical properties, and thermal stability of the scaffolds were discussed. It was found that the moving speed of the receiving plate had the most significant effect on the scaffold performance, followed by the receiving distance and spinning voltage. The results also showed that these process parameters affected the fiber diameter, corresponding coefficient of variation, porosity of the composite scaffolds, and mechanical properties of the samples, including the tensile strength and fiber peeling strength. Moreover, the process parameters could influence the thermal degradation performance and melting process. Although the mass loss of the composite scaffolds was not obvious after degradation, the mechanical performance degraded severely. It was concluded that the more appropriate process parameters for preparing PCL/nHA scaffolds were a spinning voltage of -4 kV, receiving distance of 4 mm, moving speed of receiving plate of 5 mm/s, and melt temperature of 130 °C. This study proved that near-field direct-writing melt electrospinning technology is a good method to obtain PCL/nHA composite scaffolds with an excellent mechanical properties and desired morphology for future tissue engineering applications.

Vitamin D and curcumin-loaded PCL nanofibrous for engineering osteogenesis and immunomodulatory scaffold

The accelerating bone healing process is still a major challenge in clinical orthopedics, especially in critical-sized bone defects. Recently, Nanofiber membranes are showing increasing attention in the biomedical field due to their good biocompatibility, mechanical stability, and the ability to work as a drug carrier to achieve localized and sustained drug delivery. Herein, a multifunction nanofiber membrane loaded with vitamin D (Vit D) and curcumin (Cur) was successfully fabricated using electrospinning technology. In addition, we innovatively modified Vit D with PEG to improve the hydrophilicity of PCL nanofibers. The vitro results of CCK-8, alkaline phosphatase (ALP) and mineralization demonstrated that the PCL/Vit D-Cur membrane had great potential for enhancing the proliferation/differentiation of osteoblasts. Moreover, the synergistic effect of Vit D-Cur loaded PCL nanofiber membrane showed a superior ability to improve the anti-inflammatory activity through M2 polarization. Furthermore, in vivo results confirmed that the defect treated with PCL/Vit D-Cur nanofiber membrane was filled with the newly formed bone after 1 month. These results indicate that the Vit D/Cur loaded membrane can be applied for potential bone regeneration therapy.

Ceramic Nanofiber Materials for Wound Healing and Bone Regeneration: A Brief Review

Ceramic nanofibers have been shown to be a new horizon of research in the biomedical area, due to their differentiated morphology, nanoroughness, nanotopography, wettability, bioactivity, and chemical functionalization properties. Therefore, considering the impact caused by the use of these nanofibers, and the fact that there are still limited data available in the literature addressing the ceramic nanofiber application in regenerative medicine, this review article aims to gather the state-of-the-art research concerning these materials, for potential use as a biomaterial for wound healing and bone regeneration, and to analyze their characteristics when considering their application.

Electrospun Silk Fibroin/kappa-Carrageenan Hybrid Nanofibers with Enhanced Osteogenic Properties for Bone Regeneration Applications

In this study, a novel nanofibrous hybrid scaffold based on silk fibroin (SF) and different weight ratios of kappa-carrageenan (k-CG) (1, 3, and 5 mg of k-CG in 1 mL of 12 wt% SF solution) was prepared using electrospinning and genipin (GP) as a crosslinker. The presence of k-CG in SF nanofibers was analyzed and confirmed using Fourier transform infrared spectroscopy (FTIR). In addition, X-ray diffraction (XRD) analysis confirmed that GP could cause SF conformation to shift from random coils or α-helices to β-sheets and thereby facilitate a more crystalline and stable structure. The ultimate tensile strength (UTS) and Young's modulus of the SF mats were enhanced after crosslinking with GP from 3.91 ± 0.2 MPa to 8.50 ± 0.3 MPa and from 9.17 ± 0.3 MPa to 31.2 ± 1.2 MP, respectively. Notably, while the mean fiber diameter, wettability, and biodegradation rate of the SF nanofibers increased with increasing k-CG content, a decreasing effect was determined in terms of UTS and Young's modulus. Additionally, better cell viability and proliferation were observed on hybrid scaffolds with the highest k-CG content. Osteogenic differentiation was determined from alkaline phosphatase (ALP) activity and Alizarin Red staining and expression of osteogenic marker genes. To this end, we noticed that k-CG enhanced ALP activity, calcium deposition, and expression of osteogenic genes on the hybrid scaffolds. Overall, hybridization of SF and k-CG can introduce a promising scaffold for bone regeneration; however, more biological evaluations are required.

Roles of Chondroitin Sulfate Proteoglycans as Regulators of Skeletal Development

The extracellular matrix (ECM) is critically important for most cellular processes including differentiation, morphogenesis, growth, survival and regeneration. The interplay between cells and the ECM often involves bidirectional signaling between ECM components and small molecules, i.e., growth factors, morphogens, hormones, etc., that regulate critical life processes. The ECM provides biochemical and contextual information by binding, storing, and releasing the bioactive signaling molecules, and/or mechanical information that signals from the cell membrane integrins through the cytoskeleton to the nucleus, thereby influencing cell phenotypes. Using these dynamic, reciprocal processes, cells can also remodel and reshape the ECM by degrading and re-assembling it, thereby sculpting their environments. In this review, we summarize the role of chondroitin sulfate proteoglycans as regulators of cell and tissue development using the skeletal growth plate model, with an emphasis on use of naturally occurring, or created mutants to decipher the role of proteoglycan components in signaling paradigms.

The Effect of Low-Temperature Thermal Processing on Bovine Hydroxyapatite Bone Substitutes, toward Bone Cell Interaction and Differentiation

Ideal bone grafting scaffolds are osteoinductive, osteoconductive, and encourage osteogenesis through the remodeling processes of bone resorption, new bone formation, and successful integration or replacement; however, achieving this trifecta remains challenging. Production methods of bone grafts, such as thermal processing, can have significant effects on the degree of cell-surface interactions via wide-scale changes in the material properties. Here, we investigated the effects of small incremental changes at low thermal processing temperatures on the degree of osteoclast and osteoblast attachment, proliferation, and differentiation. Bovine bone scaffolds were prepared at 100, 130, 160, 190, and 220 °C and compared with a commercial control, Bio-Oss^®. Osteoclast attachment and activity were significantly higher on lower temperature processed bone and were not present ≥190 °C. The highest osteoblast proliferation and differentiation were obtained from treatments at 130 and 160 °C. Similarly, qRT²-PCR assays highlighted osteoblasts attached to bone processed at 130 and 160 °C as demonstrating the highest osteogenic gene expression. This study demonstrated the significant effects of small-scale processing changes on bone graft materials in vitro, which may translate to a tailored approach of cellular response in vivo.

Optimization of a Tricalcium Phosphate-Based Bone Model Using Cell-Sheet Technology to Simulate Bone Disorders

Bone diseases such as osteoporosis, delayed or impaired bone healing, and osteoarthritis still represent a social, financial, and personal burden for affected patients and society. Fully humanized in vitro 3D models of cancellous bone tissue are needed to develop new treatment strategies and meet patient-specific needs. Here, we demonstrate a successful cell-sheet-based process for optimized mesenchymal stromal cell (MSC) seeding on a β-tricalcium phosphate (TCP) scaffold to generate 3D models of cancellous bone tissue. Therefore, we seeded MSCs onto the β-TCP scaffold, induced osteogenic differentiation, and wrapped a single osteogenically induced MSC sheet around the pre-seeded scaffold. Comparing the wrapped with an unwrapped scaffold, we did not detect any differences in cell viability and structural integrity but a higher cell seeding rate with osteoid-like granular structures, an indicator of enhanced calcification. Finally, gene expression analysis showed a reduction in chondrogenic and adipogenic markers, but an increase in osteogenic markers in MSCs seeded on wrapped scaffolds. We conclude from these data that additional wrapping of pre-seeded scaffolds will provide a local niche that enhances osteogenic differentiation while repressing chondrogenic and adipogenic differentiation. This approach will eventually lead to optimized preclinical in vitro 3D models of cancellous bone tissue to develop new treatment strategies.

Biomimetic porous scaffolds containing decellularized small intestinal submucosa and Sr2+/Fe3+co-doped hydroxyapatite accelerate angiogenesis/osteogenesis for bone regeneration

The design of bone scaffolds is predominately aimed to well reproduce the natural bony environment by imitating the architecture/composition of host bone. Such biomimetic biomaterials are gaining increasing attention and acknowledged quite promising for bone tissue engineering. Herein, novel biomimetic bone scaffolds containing decellularized small intestinal submucosa matrix (SIS-ECM) and Sr²⁺/Fe³⁺co-doped hydroxyapatite (SrFeHA) are fabricated for the first time by the sophisticated self-assembled mineralization procedure, followed by cross-linking and lyophilization post-treatments. The results indicate the constructed SIS/SrFeHA scaffolds are characterized by highly porous structures, rough microsurface and improved mechanical strength, as well as efficient releasing of bioactive Sr²⁺/Fe³⁺and ECM components. These favorable physico-chemical properties endow SIS/SrFeHA scaffolds with an architectural/componential biomimetic bony environment which appears to be highly beneficial for inducing angiogenesis/osteogenesis both in vitro and in vivo. In particular, the cellular functionality and bioactivity of endotheliocytes/osteoblasts are significantly enhanced by SIS/SrFeHA scaffolds, and the cranial defects model further verifies the potent ability of SIS/SrFeHA to accelerate in vivo vascularization and bone regeneration following implantation. In this view these results highlight the considerable angiogenesis/osteogenesis potential of biomimetic porous SIS/SrFeHA scaffolds for inducing bone regeneration and thus may afford a new promising alternative for bone tissue engineering.

Enhanced Bone Regeneration via PHA Scaffolds Coated with Polydopamine-Captured BMP2

The hierarchical three-dimensional (3D)-printing scaffolds based on microbial polyester poly(3-hydrxoybutyrate-co-4-hydroxybutyrate) (P34HB) were designed and used for bone tissue engineering via surface functionalization on the 3D-printed (P34HB) scaffolds using polydopamine (PDA)-mediated...

Biologically modified implantation as therapeutic bioabsorbable materials for bone defect repair

For decades, researches have concentrated on the mechanical properties, biodegradation, and biocompatibility of implants used in the therapy of large size bone defect. In vivo studies demonstrate that bioabsorbable bone substitute materials can reduce the risk of common symptoms such as inflammation and osteonecrosis caused by bio-inert materials after long-term implantation. Several organic, inorganic, and composite materials have been approved for clinical application, based on their unique characteristics and advantages. Although some artificial bioabsorbable bone substitute materials have been used for years, there are still some disadvantages existing, such as low mechanical strength, high brittleness, and low degradation rate. Therefore, novel bioabsorbable composite materials biomaterials have been developed for bone defect repair. In this review, we provide an overview of the development of artificial bioabsorbable bone substitute materials and highlight the advantages and disadvantages. Furthermore, recent advances in bioabsorbable bone substitute materials used in bone defect repair are outlined. Finally, we discuss current challenges and further developments in the clinical application of bioabsorbable bone substitute materials.

Nanocomposites of Chitosan/Graphene Oxide/Titanium Dioxide Nanoparticles/Blackberry Waste Extract as Potential Bone Substitutes

New technologies based on nanocomposites of biopolymers and nanoparticles inspired by the nature of bone structure have accelerated their application in regenerative medicine, thanks to the introduction of reinforcing properties. Our research incorporated chitosan (CS) covalently crosslinked with glutaraldehyde (GLA) beads with graphene oxide (GO) nanosheets, titanium dioxide nanoparticles (TiO₂), and blackberry processing waste extract (BBE) and evaluated them as partial bone substitutes. Skullbone defects in biomodels filled with the scaffolds showed evidence through light microscopy, scanning electron microscopy, histological studies, soft tissue development with hair recovery, and absence of necrotic areas or aggressive infectious response of the immune system after 90 days of implantation. More interestingly, newly formed bone was evidenced by elemental analysis and Masson trichromacy analysis, which demonstrated a possible osteoinductive effect from the beads using the critical size defect experimental design in the biomodels. The results of this research are auspicious for the development of bone substitutes and evidence that the technologies for tissue regeneration, including chitosan nanocomposites, are beneficial for the adhesion and proliferation of bone cells.

Hydroxyapatite Obtained via the Wet Precipitation Method and PVP/PVA Matrix as Components of Polymer-Ceramic Composites for Biomedical Applications

The aspect of drug delivery is significant in many biomedical subareas including tissue engineering. Many studies are being performed to develop composites with application potential for bone tissue regeneration which at the same provide adequate conditions for osteointegration and deliver the active substance conducive to the healing process. Hydroxyapatite shows a great potential in this field due to its osteoinductive and osteoconductive properties. In the paper, hydroxyapatite synthesis via the wet precipitation method and its further use as a ceramic phase of polymer-ceramic composites based on PVP/PVA have been presented. Firstly, the sedimentation rate of hydroxyapatite in PVP solutions has been determined, which allowed us to select a 15% PVP solution (sedimentation rate was 0.0292 mm/min) as adequate for preparation of homogenous reaction mixture treated subsequently with UV radiation. Both FT-IR spectroscopy and EDS analysis allowed us to confirm the presence of both polymer and ceramic phase in composites. Materials containing hydroxyapatite showed corrugated and well-developed surface. Composites exhibited swelling properties (hydroxyapatite reduced this property by 25%) in simulated physiological fluids, which make them useful in drug delivery (swelling proceeds parallel to the drug release). The short synthesis time, possibility of preparation of composites with desired shapes and sizes and determined physicochemical properties make the composites very promising for biomedical purposes.

AK, Olaiya NG, Iqbal MO, Jummaat F, A.K. AS, Adnan AS. Insights into the Role of Biopolymer Aerogel Scaffolds in Tissue Engineering and Regenerative Medicine

The global transplantation market size was valued at USD 8.4 billion in 2020 and is expected to grow at a compound annual growth rate of 11.5% over the forecast period. The increasing demand for tissue transplantation has inspired researchers to find alternative approaches for making artificial tissues and organs function. The unique physicochemical and biological properties of biopolymers and the attractive structural characteristics of aerogels such as extremely high porosity, ultra low-density, and high surface area make combining these materials of great interest in tissue scaffolding and regenerative medicine applications. Numerous biopolymer aerogel scaffolds have been used to regenerate skin, cartilage, bone, and even heart valves and blood vessels by growing desired cells together with the growth factor in tissue engineering scaffolds. This review focuses on the principle of tissue engineering and regenerative medicine and the role of biopolymer aerogel scaffolds in this field, going through the properties and the desirable characteristics of biopolymers and biopolymer tissue scaffolds in tissue engineering applications. The recent advances of using biopolymer aerogel scaffolds in the regeneration of skin, cartilage, bone, and heart valves are also discussed in the present review. Finally, we highlight the main challenges of biopolymer-based scaffolds and the prospects of using these materials in regenerative medicine.

Scaffolds from Self-Assembling Tetrapeptides Support 3D Spreading, Osteogenic Differentiation, and Angiogenesis of Mesenchymal Stem Cells

The apparent rise of bone disorders demands advanced treatment protocols involving tissue engineering. Here, we describe self-assembling tetrapeptide scaffolds for the growth and osteogenic differentiation of human mesenchymal stem cells (hMSCs). The rationally designed peptides are synthetic amphiphilic self-assembling peptides composed of four amino acids that are nontoxic. These tetrapeptides can quickly solidify to nanofibrous hydrogels that resemble the extracellular matrix and provide a three-dimensional (3D) environment for cells with suitable mechanical properties. Furthermore, we can easily tune the stiffness of these peptide hydrogels by just increasing the peptide concentration, thus providing a wide range of peptide hydrogels with different stiffnesses for 3D cell culture applications. Since successful bone regeneration requires both osteogenesis and vascularization, our scaffold was found to be able to promote angiogenesis of human umbilical vein endothelial cells (HUVECs) in vitro. The results presented suggest that ultrashort peptide hydrogels are promising candidates for applications in bone tissue engineering.

A hierarchical scaffold with a highly pore-interconnective 3D printed PLGA/n-HA framework and an extracellular matrix like gelatin network filler for bone regeneration

The ideal scaffold for bone repair should have a hierarchical pore structure and gradient degradation performance to satisfy the uniform adhesion and proliferation of cells in the scaffold at the early stage of implantation, as well as providing space for the subsequent regeneration of bone tissue. To this end, we developed a hierarchical polylactic acid glycolic acid copolymer (PLGA)/nano-hydroxyapatite (n-HA)/gelatin (Gel) (PHG) scaffold with a printed PLGA/n-HA (PH) framework and a Gel network filler for bone regeneration by the combination of 3D printing and freeze-drying technologies. The fabricated PHG scaffold features large front hole size (>1100 μm × 1100 μm) and side hole size (>500 μm) to provide sufficient open space and reliable integrated support for cell and tissue ingrowth. The gelatin network filled in the PH framework played the role of a cell holder just like an extracellular matrix (ECM) in the early stage. In vitro degradation experiments revealed that the gelatin network completely degraded within 5 weeks while the structural integrity of the framework still remained at the 32nd week. The results of cell culture confirmed that the PHG scaffold was more conducive to cell attachment. In vivo assessments in a rat femoral defect model showed that PHG scaffolds were more favored for new bone formation and achieving a tighter bond between the scaffold and the original tissues. The hierarchical PHG scaffold has great application potential in bone tissue engineering and will provide a reference for the model design of bone scaffolds.