Poly(ionic liquid)s: An update

Heteroployacid on the composite of boehmite and polyionic liquid as a catalyst for alcohol oxidation and tandem alcohol oxidation Knoevenagel condensation reactions

Using boehmite as an available and low-cost natural compound, a bi-functional catalytic composite is prepared through vinyl-functionalization of boehmite, followed by polymerization with the as-prepared bis-vinylimidazolium bromide ionic liquid and supporting of phosphotungstic acid. The catalyst was characterized via ICP, XRD, TGA, FTIR, SEM/EDS and elemental mapping analysis and applied for promoting alcohol oxidation reaction and one-pot tandem alcohol oxidation/Knoevenagel condensation reaction in aqueous media under mild reaction condition. The results indicated high catalytic activity of the catalyst for both reactions. This protocol showed high generality and aliphatic, aromatic and heterocyclic alcohols could be applied as substrates to furnish the corresponding products in high to excellent yields. Furthermore, hot filtration test confirmed true heterogeneous nature of the catalysis. The catalyst could also be recovered readily and reused for at least five runs of the reaction with low loss of the activity and phosphotungstic acid leaching upon each run.

Poly(ionic liquid) Gating Materials for High-Performance Organic Thin-Film Transistors: The Role of Block Copolymer Self-Assembly at the Semiconductor Interface

The widespread realization of wearable electronics requires printable active materials capable of operating at low voltages. Polymerized ionic liquid (PIL) block copolymers exhibit a thickness-independent double-layer capacitance that makes them a promising gating medium for the development of organic thin-film transistors (OTFTs) with low operating voltages and high switching speed. PIL block copolymer structure and self-assembly can influence ion conductivity and the resulting OTFT performance. In an OTFT, self-assembly of the PIL gate on the semiconducting polymer may differ from bulk self-assembly, which would directly influence electrical double-layer formation. To this end, we used poly{[N,N'-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} (P(NDI2OD-T2)) as a model semiconductor for our OTFTs, on which our PILs exhibited self-assembly. In this study, we explore this critical interface by grazing-incidence small-angle X-ray scattering (GISAXS) and atomic force microscopy (AFM) of P(NDI2OD-T2) and a series of poly(styrene)-b-poly(1-(4-vinylbenzyl)-3-butylimidazolium-random-poly(ethylene glycol) methyl ether methacrylate) (poly(S)-b-poly(VBBI⁺[X]-r-PEGMA)) block copolymers with varying PEGMA/VBBI⁺ ratios and three different mobile anions (where X = TFSI^-, PF₆^-, or BF₄^-). We investigate the thin-film self-assembly of block copolymers as a function of device performance. Overall, a mixed orientation at the interface leads to improved device performance, while predominantly hexagonal packing leads to nonfunctional devices, regardless of the anion present. These PIL gated OTFTs were characterized with a threshold voltage below 1 V, making understanding of their structure-property relationships crucial to enabling the further development of high-performance gating materials.

Ionic Liquid-Based Polymer Nanocomposites for Sensors, Energy, Biomedicine, and Environmental Applications: Roadmap to the Future

Current interest toward ionic liquids (ILs) stems from some of their novel characteristics, like low vapor pressure, thermal stability, and nonflammability, integrated through high ionic conductivity and broad range of electrochemical strength. Nowadays, ionic liquids represent a new category of chemical-based compounds for developing superior and multifunctional substances with potential in several fields. ILs can be used in solvents such as salt electrolyte and additional materials. By adding functional physiochemical characteristics, a variety of IL-based electrolytes can also be used for energy storage purposes. It is hoped that the present review will supply guidance for future research focused on IL-based polymer nanocomposites electrolytes for sensors, high performance, biomedicine, and environmental applications. Additionally, a comprehensive overview about the polymer-based composites' ILs components, including a classification of the types of polymer matrix available is provided in this review. More focus is placed upon ILs-based polymeric nanocomposites used in multiple applications such as electrochemical biosensors, energy-related materials, biomedicine, actuators, environmental, and the aviation and aerospace industries. At last, existing challenges and prospects in this field are discussed and concluding remarks are provided.

Sulfonates as Versatile Structural Counterions of Epoxidized Salts

Ionic liquids have recently emerged as monomers to synthesize multifunctional polymeric materials. Among such species, ionic epoxy-based networks represent promising but underdeveloped materials that are hindered by tricky access to the functionalized ionic liquid monomers. To date, the reported epoxidized imidazolium salts have focused on highly toxic epichlorohydrin. This study concerns flexible and efficient methods to synthesize versatile building blocks with sulfonates as valuable anions. The judicious combination of an aliphatic or aromatic sulfonate with an imidazolium leads to new epoxidized salts with high structural variability and good chemical and thermal stability (>300 °C).

Poly(ionic liquid)-Armored MXene Membrane: Interlayer Engineering for Facilitated Water Transport

Two-dimensional (2D) MXene-based lamellar membranes bearing interlayers of tunable hydrophilicity are promising for high-performance water purification. The current challenge lies in how to engineer the pore wall's surface properties in the subnano-confinement environment while ensuring its high selectivity. Herein, poly(ionic liquid)s, equipped with readily exchangeable counter anions, succeeded as a hydrophilicity modifier in addressing this issue. Lamellar membranes bearing nanochannels of tailorable hydrophilicity are constructed via assembly of poly(ionic liquid)-armored MXene nanosheets. By shifting the interlayer galleries from being hydrophilic to more hydrophobic via simple anion exchange, the MXene membrane performs drastically better for both the permeance (by two-fold improvement) and rejection (≈99 %). This facile method opens up a new avenue for building 2D material-based membranes of enhancing molecular transport and sieving effect.

Single Lithium Ion Conducting "Binderlyte" for High-Performing Lithium Metal Batteries

Rechargeable lithium metal batteries (LMBs) are deemed as a viable solution to improve the power and/or energy density of the contemporary lithium-ion batteries (LIBs). However, poor Li-ion diffusivity within high-energy cathodes causes sluggish kinetics of the corresponding redox reactions particularly at high C-rates, thereby largely impeding the performance of rechargeable LMBs. In this work, a dual-functional single Li-ion conducting polysalt is proposed as both catholyte and binding agent (coined "Binderlyte") for rechargeable LMBs. The designed Binderlyte is thermally and electrochemically stable, allowing its use for high-energy cathodes like Li(Ni_1/3 Mn_1/3 Co_1/3 )O₂ (NMC111). The implementation of designer Binderlyte endows the Li° || NMC111 cell with superior cycling stability and capacity retention even at an extremely high C-rate of 10C. In particular, the soft and flexible nature of the Binderlyte allows the thick NMC cathode to operate at extremely low porosity (20 vol%) with almost no capacity decay. This work may provide a paradigm shift on the design of innovative polymeric materials, which are essential for developing high-performing rechargeable LMBs.

Protected Poly(3-sulfopropyl methacrylate) Copolymers: Synthesis, Stability, and Orthogonal Deprotection

Because of their permanent charge, strong polyelectrolytes remain challenging to characterize, in particular, when they are combined with hydrophobic features. For this reason, they are typically prepared through a postmodification of a fully hydrophobic precursor. Unfortunately, these routes often result in an incomplete functionalization or otherwise require harsh reaction conditions, thus limiting their applicability. To overcome these problems, in this work a strategy is presented that facilitates the preparation of well-defined strong polyanions by starting from protected 3-sulfopropyl methacrylate monomers. Depending on the chemistry of the protecting group, the hydrophobic precursor could be quantitatively converted into a strong polyanion under nucleophilic, acidic, or basic conditions. As a proof of concept, orthogonally protected diblock copolymers were synthesized, selectively deprotected, and allowed to self-assemble in aqueous solution. Further conversion into a fully water-soluble polyanion was achieved by deprotecting the second block as well.

Electrically Accelerated Self-Healable Polyionic Liquid Copolymers

Electrically accelerated self-healable poly(ionic liquids) copolymers that exhibit resistor-capacitor (RC) circuit properties are developed. At low alternating current (AC) frequencies these materials behave as a resistor (R), whereas at higher frequencies as a capacitor (C). These properties are attributed to a combination of dipolar and electrostatic interactions in (1-[(2-methacryloyloxy)ethyl]-3-butylimidazolium bis(trifluoromethyl-sulfonyl)imide) copolymerized with methyl methacrylate (MMA) monomers to form p(MEBIm-TSFI/MMA)] copolymers. When the monomer molar ratio (MEBIm-TSFI:MMA) is 40/60, these copolymers are capable of undergoing multiple damage-repair cycles and self-healing is accelerated by the application of alternating 1.0-4.0 V electric field (EF). Self-healing in the absence of EFs is facilitated by van der Waals (vdW) interactions, but the application of AC EF induces back and forth movement of charges against the opposing force that result in dithering of electrostatic dipoles giving rise to interchain physical crosslinks. Electrostatic inter- and intrachain interactions facilitated by copolymerization of ionic liquid monomers with typically dielectric acrylic-based monomers result in enhanced cohesive energy densities that accelerate the recovery of vdW forces facilitating self-healing. Incorporating ionic liquids into commodity polymers offers promising uses as green conducting solid polyelectrolytes in self-healable energy storage, energy-harvesting devices, and many other applications.

A Computer Simulation Study of Thermal and Mechanical Properties of Poly(Ionic Liquid)s

Thermal and mechanical properties of poly(ionic liquid)s (PILs), an epoxidized ionic liquid-amine network, are studied via molecular dynamics simulations. The poly(ionic liquid)s are designed with two different ionic liquid monomers, 3-[2-(Oxiran-2-yl)ethyl]-1-{4-[(2-oxiran-2-yl)ethoxy]phenyl}imidazolium (EIM2) and 1-{4-[2-(Oxiran-2-yl)ethyl]phenyl}-3-{4-[2-(oxiran-2-yl)ethoxy]benzyl}imidazolium (EIM1), each of which is networked with tris(2-aminoethyl)amine, paired with different anions, bis(trifluoromethanesulfonyl)imide (TFSI⁻) and chloride (Cl⁻). We investigate how ionic liquid monomers with high ionic strength affect structures of the cross-linked polymer networks and their thermomechanical properties such as glass transition temperature (T_g) and elastic moduli, varying the degree of cross-linking. Strong electrostatic interactions between the cationic polymer backbone and anions build up their strong structures of which the strength depends on their molecular structures and anion size. As the anion size decreases from TFSI⁻ to Cl⁻, both T_g and elastic moduli of the PIL increase due to stronger electrostatic interactions present between their ionic moieties, making it favorable for the PIL to organize with stronger bindings. Compared to the EIM2 monomer, the EIM1 monomers and TFSI⁻ ions generate a PIL with higher T_g and elastic moduli. This attributes to the less flexible structure of the EIM1 monomer for the chain rotation, in which steric hindrance by ring moieties in the EIM1-based PIL enhances their structural rigidity. The π-π stacking structures between the rings are found to increase in EIM1-based PIL compared to the EIM2-based one, which becomes stronger with smaller Cl⁻ ion rather than TFSI⁻. The effect of the degree of the cross-linking on thermal and mechanical properties is also examined. As the degree of cross-linking decreases from 100% to 60%, T_g also decreases by a factor of 10–20%, where the difference among the given PILs becomes decreased with a lower degree of cross-linking. Both the Young’s (E) and shear (G) moduli of all the PILs decrease with degree of cross-linking, which the reduction is more significant for the PIL generated with EIM2 monomers. Transport properties of anions in PILs are also studied. Anions are almost immobilized globally with very small structural fluctuations, in which Cl⁻ presents lower diffusivity by a factor of ~2 compared to TFSI⁻ due to their stronger binding to the cationic polymer backbone.

Hydrophilic and Positively Charged Polyvinylidene Fluoride Membranes for Water Treatment with Excellent Anti-Oil and Anti-Biocontamination Properties

Membrane fouling limits the rapid development of membrane separations. In this study, a blend membrane containing polycationic liquid (P(BVImBr₁-co-PEGMA₁)) is presented that can improve the antifouling performance of polyvinylidene fluoride (PVDF) membranes. By mixing the polycationic liquid into PVDF, an improved membrane-surface hydrophilicity and enlarged membrane porosity were detected. The water contact angle decreased from 82° to 67°, the porosity enlarged from 7.22% to 89.74%, and the pure water flux improved from 0 to 631.68 L m⁻² h⁻¹. The blend membrane surfaces were found to be always positively charged at pH 3~10. By applying the membranes to the filtration of oil/water emulsion and bovine serum albumin (BSA) solution, they showed a very high rejection rate to pollutants in wastewater (99.4% to oil droplets and 85.6% to BSA). The positive membrane surface charge and the increased membrane hydrophilicity resulted in excellent antifouling performance, with the flux recovery rates of the dynamic filtration tests reaching 97.3% and 95.5%, respectively. Moreover, the blend membranes demonstrated very low BSA adhesion and could even kill S. aureus, showing excellent antifouling properties.

Siloxane-Based Main-Chain Poly(ionic liquid)s via a Debus-Radziszewski Reaction

Herein, we synthesized a series of siloxane-based poly(ionic liquid)s (PILs) with imidazolium-type species in the main chain via the multicomponent Debus–Radziszewski reaction. We employed oligodimethylsiloxane diamine precursors to integrate flexible spacers in the polymer backbone and ultimately succeeded in obtaining main-chain PILs with low glass transition temperatures (T_gs) in the range of −40 to −18 °C. Such PILs were combined with conventional hydrophobic vinylimidazolium-based PILs for the fabrication of porous membranes via interpolyelectrolyte complexation with poly(acrylic acid), which leads to enhanced mechanical performance in the tensile testing measurements. This study will enrich the structure library of main-chain PILs and open up more opportunities for potential industrial applications of porous imidazolium-based membranes.

Recent advances in poly(ionic liquid)s for biomedical application

Poly(ionic liquid)s (PILs) are polymers containing ions in their side-chain or backbone, and the designability and outstanding physicochemical properties of PILs have attracted widespread attention from researchers. PILs have specific characteristics, including negligible vapor pressure, high thermal and chemical stability, non-flammability, and self-assembly capabilities. PILs can be well combined with advanced analytical instruments and technology and have made outstanding contributions to the development of biomedicine aiding in the continuous advancement of science and technology. Here we reviewed the advances of PILs in the biomedical field in the past five years with a focus on applications in proteomics, drug delivery, and development. This paper aims to engage pharmaceutical and biomedical scientists to full understand PILs and accelerate the progress from laboratory research to industrialization.

Tuning the activity and selectivity of polymerised ionic liquid-stabilised ruthenium nanoparticles through anion exchange reactions

The development of highly active and selective heterogeneous-based catalysts with tailorable properties is not only a fundamental challenge, but is also crucial in the context of energy savings and sustainable chemistry. Here, we show that ruthenium nanoparticles (RuNPs) stabilised with simple polymerised ionic liquids (PILs) based on N-vinyl imidazolium led to highly active and robust nano-catalysts in hydrogenation reactions, both in water and organic media. Of particular interest, their activity and selectivity could simply be manipulated through counter-anion exchange reactions. Hence, as a proof of concept, the activity of RuNPs could be reversibly turned on and off in the hydrogenation of toluene, while in the case of styrene, the hydrogenation could be selectively switched from ethylbenzene to ethylcyclohexane upon anion metathesis. According to X-ray photoelectron spectroscopy (XPS) and dynamic light scattering (DLS) analyses, these effects could originate not only from the relative hydrophobicity and solvation of the PIL corona but also from the nature and strength of the PIL-Ru interactions.

Thermodynamic stability of cis-azobenzene containing DNA materials based on van der Waals forces

Taking advantage of van der Waals forces, an azobenzene-containing surfactant with a stable cis-state was designed and synthesized to fabricate photoresponsive DNA material. The reported DNA material exhibited reversible liquid crystalline-to-isotropic liquid transition under UV/Vis illuminations via the trans-cis isomerization of azobenzene. It also gained the ability to maintain the isotropic liquid state after UV light had ceased thanks to the thermodynamic stability of the cis-isomer of the azobenzene-containing surfactant. This work provides a design strategy for fabricating photoresponsive phase-change biomaterials.

New Epoxy Thermosets Organic-Inorganic Hybrid Nanomaterials Derived from Imidazolium Ionic Liquid Monomers and POSS®Ph

New epoxy-amine networks issue from epoxydized imidazolium ionic liquid monomers (ILMs) and isophorone diamine (IPD) were modified for the first time by incorporating unmodified trisilanol phenyl POSS® (POSS®Ph-triol) and two ionic liquid-modified POSS®Ph (IL-g-POSS®Ph) having chloride (Cl-) and bis-trifluoromethanesulfonimidate (NTf2-) counter anions. Then, 5 wt.% of unmodified and IL-modified POSS®Ph were introduced in order to develop new solid electrolytes. First, a homogeneous dispersion of the POSS®Ph aggregates (diameters from 80 to 400 nm) into epoxy networks was observed. As a consequence, ILM/IPD networks with glass transition temperatures between 45 and 71 °C combined with an enhancement of the thermal stability (>380 °C) were prepared. Moreover, a significant increase of the hydrophobic character and high oil repellency of the network surfaces were obtained by using IL-g-POSS®Ph (19-20 mJ.m-2), opening up promising prospects for surface coating applications. Finally, these new epoxy networks exhibited outstanding high ionic conductivities (from 3.4 × 10-8 to 6.8 × 10-2 S.m-1) combined with an increase in permitivity.

Photoregulative phase change biomaterials showing thermodynamic and mchanical stabilities

Azobenzenes are great photochromic molecules for switching the physical properties of various materials via trans-cis isomerization. However, the UV light resulted cis-azobenzene is metastable and thermodynamically gets back to trans-azobenzene after ceasing UV irradiation, which causes an unwanted property change of azobenzene-containing materials. Additionally, thermal and mechanical conditions would accelerate this process dramatically. In this present work, a new type of azobenzene-containing surfactant is designed for the fabrication of photoresponsive phase change biomaterials. With a "locked" cis-azobenzene conformation, the resulting biomaterials could maintain their disordered state after ceasing UV light, which exhibit great resistance to thermal and piezo conditions. Interestingly, the "locked" cis-azobenzene could be unlocked by Vis light in high efficiency, which opens a new way for the design of phase change materials only responding to light. By showing stable cis-azobenzene maintained physical state, the newly fabricated biomaterials provide new potential for the construction of advanced materials, like self-healing materials, with less use of long time UV irradiation for maintaining their disordered states.

Exploration of Ion Transport in Blends of an Ionic Liquid and a Polymerized Ionic Liquid Graft Copolymer

In this study, we prepared a composite membrane consisting of a poly(1-butyl-3-vinylimidazolium-tetrafluoroborate) (poly([BVIM]-[BF₄])) polymerized ionic liquid graft copolymer (PILGC) and a blend of PILGC and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]-[BF₄]) ionic liquid (IL) to explore techniques for improving the conductivity of PILGCs, which is normally three orders of magnitude lower than that of ILs. PILGCs, which are environmentally friendly, have attracted much interest. To gain a better understanding of ion transport in composites, the mechanisms of ion transport in composite components should be explored. We investigated anion transport in ILs and PILGCs and were able to obtain the correct ion transport mechanisms in IL-PILGC blends based on a previous work. We performed molecular dynamics (MD) simulations, which are commonly used to investigate molecular mechanisms. According to the MD simulation results, in most IL-PILGC blends of various compositions, the contributions of cations are greater than those of anions. This is one reason that blends have higher conductivities than their component PILGCs. To the best of our knowledge, we are the first to identify ion transport mechanisms in PILGCs and their blends with ILs by exploring subdiffusive ion motion regimes. The ratio of the number of cages with more than three cationic branch chains in the blend with 50 wt % PILGC, the blend with 80 wt % PILGC, and the PILGC was 0.26:0.39:0.65. Therefore, the ratio of firm cages gets a promotion as the PILGC content increases. Because the ratio of fast ions decreases as the ratio of firm cages increases, the blend with 80 wt % PILGC has lower anion diffusivities than the blend with 50 wt % PILGC. It was inappropriate to probe ion transport in PILGCs (or IL-PILGC blends) solely via analyzing ion association interactions. Analysis of only ion association interactions led to the incorrect conclusion that the time scales of ion transport in PILGCs are given by the continuous ion association time, which is the time when the ion association remains paired rather than the time when an ion is caught inside a cage. Proper methods should be used to obtain more accurate theories.

Immobilization of molecule-based ionic liquids: a promising approach to improve elecrocatalyst performance towards the hydrogen evolution reaction

Ionic liquids (ILs) have received continuous attention owing to their unique chemical and physical properties and to their successful integration in several applications.

Inorganic reinforced poly(ionic liquid) microcapsules: confined cooling-assisted phase separation self-assembly and enhanced electro-responsive property

We report a simple preparation of inorganic reinforced poly(ionic liquid) (PIL) microcapsules by combining dispersion polymerization and confined cooling-assisted phase separation self-assembly. Silane coupling agent-modified PIL microbeads were first prepared by dispersion polymerization. Then, the microbeads were dissolved in a mixed solvent composed of good solvent and non-solvent to form hollow SiO_x microcapsules at a relatively high temperature. Finally, the solution was cooled to induce the nucleation and growth of dissolved PIL chains on the inner and outer surface of hollow SiO_x microcapsules to form inorganic reinforced microcapsules with asymmetric PIL/SiO_x /PIL sandwich-like shell. The morphology of microcapsules can be controlled by adjusting PIL concentration and cooling rate. The inorganic reinforced microcapsules show enhanced suspended stability and electro-responsive characteristic when used as the dispersed phase of smart suspensions. This article is protected by copyright. All rights reserved.

Porous polyelectrolyte frameworks: synthesis, post-ionization and advanced applications

Porous organic polymers (POPs), which feature high surface areas, robust skeletons, tunable pores, adjustable functionality and versatile applicability, have constituted a designable platform to develop advanced organic materials. Endowing polyelectrolytes with the distinct characteristics of POPs will attract mounting interest as the structural diversity of polyelectrolytes will bring the new hope of intriguing applications and potential benefits. In this review, the striking progress in ionized POPs (i-POPs) has been systematically summarized with regard to their synthetic strategies and applications. In the synthesis of i-POPs, we illustrate the representative ionic building blocks and charged functional groups capable of constructing the polyelectrolyte frameworks. The synthetic methods, including direct synthesis and post-modification, are detailed for the i-POPs with amorphous or crystalline structures, respectively. Subsequently, we outline the distinctive performances of i-POPs in adsorption, separation, catalysis, sensing, ion conduction and biomedical applications. The survey concerns the interplay between the surface chemistry, ionic interaction and pore confinement that cooperatively promote the performance of i-POPs. Finally, we conclude with the remaining challenges and promising opportunities for the on-going development of i-POPs.