Applications of matrix solid-phase dispersion in food analysis

Matrix solid phase dispersion extraction of ginsenosides in the leaves of Panax ginseng C.M. Mey

The matrix solid phase dispersion (MSPD) was applied to the extraction of eight kinds of ginsenosides from the leaves of Panax ginseng C.M. Mey. The experimental conditions were examined and optimised. The extracts were analysed by high performance liquid chromatography (HPLC). When the diatomaceous earth was used as dispersant and 75% methanol was used as elution solvent, the highest extraction yields of the eight kinds of ginsenosides were obtained. For comparison, the reflux extraction was applied. The extraction yields obtained by the proposed method were comparable with those obtained by the reflux extraction. The proposed method is convenient, time-saving, and organic solvent minimising.

Matrix solid-phase dispersion with sand in chromatographic analysis of essential oils in herbs

INTRODUCTION

Matrix solid-phase dispersion (MSPD) is a very simple, cheap and relatively quick sample preparation procedure which involves simultaneous disruption and extraction of various solid and semi-solid samples due to the direct mechanical blending of the sample with a SPE sorbent, mainly C(18). Little is known about MSPD application as a sample preparation method for the analysis of essential oil components in herbs.

OBJECTIVE

To evaluate if C(18) sorbent, commonly used in MSPD process, can be substituted with sand in the procedure of essential oil analysis.

METHODOLOGY

Essential oil extracts were obtained from mint, sage, chamomile, marjoram, savory and oregano using MSPD with C(18) sorbent or sand, pressurised liquid extraction and steam distillation. Their qualitative and quantitative compositions ware established by GC-MS and GC-FID.

RESULTS

The results prove that C(18) sorbent can be substituted with sand in the procedure of essential oil analysis in herbs. The recoveries of essential oil components estimated using MSPD/sand are almost equal to those using pressurised liquid extraction.

CONCLUSION

The results presented in the paper reveal that MSPD with sand is suitable for the isolation of essential oil components from herbs. Its extraction efficiency is equivalent to pressurised liquid extraction, recognised as one of the most efficient extraction methods. The cost of MSPD procedure for essential oil analysis can be significantly diminished by substituting C(18) with sand.

Potential of a metal-organic framework as a new material for solid-phase extraction of pesticides from lettuce (Lactuca sativa), with analysis by gas chromatography-mass spectrometry

The metal-organic framework (∞)[(La(0.9)Eu(0.1))(2)(DPA)(3)(H(2)O)(3)] was tested for extraction of pyrimicarb, procymidone, malathion, methyl parathion and α- and β-endosulfan from lettuce, with analysis using GC/MS in SIM mode. Experiments were carried out in triplicate at two fortification levels (0.1 and 0.5 mg/kg), and resulted in recoveries in the range of 78-107%, with RSD values between 1.6 and 8.0% for (∞)[(La(0.9)Eu(0.1))(2)(DPA)(3)(H(2)O)(3)] sorbent. Detection and quantification limits ranged from 0.02 to 0.05 mg/kg and from 0.05 to 0.10 mg/kg, respectively, for the different pesticides studied. The method developed was linear over the range tested (0.05-10.0 μg/mL), with correlation coefficients ranging from 0.9990 to 0.9997. Comparison between (∞)[(La(0.9)Eu(0.1))(2)(DPA)(3)(H(2)O)(3)] and conventional sorbent (silica gel) showed better performance of the (∞)[(La(0.9)Eu(0.1))(2)(DPA)(3)(H(2)O)(3)] polymeric sorbent for all pesticides tested.

Analysis of phenolic xenoestrogens by pressurized CEC with amperometric detection

A new method, pressurized CEC with end-column amperometric detection using carbon paste electrode, has been developed for the separation and determination of five phenolic xenoestrogens in chicken eggs and milk powder samples. Efficient separation of five analytes was performed by pressurized CEC using a mobile phase consisting of 60% v/v ACN and 40% v/v Tris buffer (5 mmol/L, pH 8.0), +6 kV of applied voltage and 7.0 MPa of supplementary pressure. Detection limits of 50, 5, 2, 10 and 20 ng/mL for pentachlorophenol, bisphenol-A, 2,4-dichlorophenol, 4-tert-octylphenol and 4-nonylphenol, respectively, were achieved using carbon paste electrode as working electrode and +0.8 V as detection potential. Matrix solid phase dispersion extraction method had been employed during sample preparation procedure, and mean recoveries ranged from 79.2 to 102.6% at different concentrations of phenolic xenoestrogens for spiked egg and milk powder samples were obtained.

An experimental design approach employing artificial neural networks for the determination of potential endocrine disruptors in food using matrix solid-phase dispersion

Matrix solid-phase dispersion (MSPD) as a sample preparation method for the determination of two potential endocrine disruptors, linuron and diuron and their common metabolites, 1-(3,4-dichlorophenyl)-3-methylurea (DCPMU), 1-(3,4-dichlorophenyl) urea (DCPU) and 3,4-dichloroaniline (3,4-DCA) in food commodities has been developed. The influence of the main factors on the extraction process yield was thoroughly evaluated. For that purpose, a 3 fractional factorial design in further combination with artificial neural networks (ANNs) was employed. The optimal networks found were afterwards used to identify the optimum region corresponding to the highest average recovery displaying at the same time the lowest standard deviation for all analytes. Under final optimal conditions, potato samples (0.5 g) were mixed and dispersed on the same amount of Florisil. The blend was transferred on a polypropylene cartridge and analytes were eluted using 10 ml of methanol. The extract was concentrated to 50 microl of acetonitrile/water (50:50) and injected in a high performance liquid chromatography coupled to UV-diode array detector system (HPLC/UV-DAD). Recoveries ranging from 55 to 96% and quantification limits between 5.3 and 15.2 ng/g were achieved. The method was also applied to other selected food commodities such as apple, carrot, cereals/wheat flour and orange juice demonstrating very good overall performance.

p-Nitro-N-propylaniline/silica: Synthesis, characterization, and its application in matrix solid phase dispersion for multiresidue analysis of pesticides in carrots

A new material for matrix solid phase dispersion (MSPD) was synthesized -- p-nitro-N-propylaniline/silica (pNNPASi) by grafting reactions, characterized by elemental analysis and N(2)-adsorption-desorption isotherms, and tested for multiclass multiresidue analysis of pesticides in wet and freeze-dried carrots. Results obtained applying this new solid phase sorbent to MSPD extraction of ten pesticides (trichlorphon, trifluralin, dicloran, chlorothalonil, prometryn, linuron, captan, procymidone, prochloraz, and deltametrin) in wet carrots showed better results than the ones obtained for freeze-dried samples. Recoveries were in the range of 48-106% and precisions varied from 6 to 20% when wet samples were employed. Comparison between pNNPASi sorbent and C(18) showed better performance of pNNPASi for eight out of ten pesticides tested. The LOQs show that the developed method can be used to detect the pesticides investigated in carrots at concentrations below the maximum residue levels (MRL) established by EU, USEPA, and National Sanitary Surveillance Agency (ANVISA). Linuron, captan, prochloraz, and deltamethrin were found in at least one of the two commercial samples studied in concentrations above the LOQ of this method. Concentrations of the last three pesticides were above the European MRL in one of the commercial samples.

Methods of sample preparation for determination of pesticide residues in food matrices by chromatography-mass spectrometry-based techniques: a review

Much progress has been made in pesticide analysis over the past decade, during which time hyphenated techniques involving highly efficient separation and sensitive detection have become the techniques of choice. Among these, methods based on chromatographic separation with mass spectrometric detection have resulted in greater likelihood of identification and are acknowledged to be extremely useful and authoritative methods for determination of pesticide residues. Even with such powerful instrumental techniques, however, the risk of interference increases with the complexity of the matrix studied, so sample preparation before instrumental analysis is still mandatory in many applications, for example food analysis. This article summarizes the analytical characteristics of the different methods of sample-preparation for determination of pesticide residues in a variety of food matrices, and surveys their recent applications in combination with chromatographic mass spectrometric analysis. We discuss the advantages and the disadvantages of the different methods, address instrumental aspects, and summarize conclusions and perspectives for the future.

Development and validation of a multi-residue method for pesticide determination in honey using on-column liquid–liquid extraction and liquid chromatography–tandem mass spectrometry

We report on the development and validation under ISO 17025 criteria of a multi-residue confirmatory method to identify and quantify 17 widely chemically different pesticides (insecticides: Carbofuran, Methiocarb, Pirimicarb, Dimethoate, Fipronil, Imidacloprid; herbicides: Amidosulfuron, Rimsulfuron, Atrazine, Simazine, Chloroturon, Linuron, Isoxaflutole, Metosulam; fungicides: Diethofencarb) and 2 metabolites (Methiocarb sulfoxide and 2-Hydroxytertbutylazine) in honey. This method is based on an on-column liquid-liquid extraction (OCLLE) using diatomaceous earth as inert solid support and liquid chromatography (LC) coupled to mass spectrometry (MS) operating in tandem mode (MS/MS). Method specificity is ensured by checking retention time and theoretical ratio between two transitions from a single precursor ion. Linearity is demonstrated all along the range of concentration that was investigated, from 0.1 to 20 ng g(-1) raw honey, with correlation coefficients ranging from 0.921 to 0.999, depending on chemicals. Recovery rates obtained on home-made quality control samples are between 71 and 90%, well above the range defined by the EC/657/2002 document, but in the range we had fixed to ensure proper quantification, as levels found in real samples could not be corrected for recovery rates. Reproducibility is found to be between 8 and 27%. Calculated CCalpha and CCbeta (0.0002-0.943 ng g(-1) for CCalpha, and 0.0002-1.232 ng g(-1) for CCbeta) show the good sensitivity attained by this multi-residue analytical method. The robustness of the method has been tested in analyzing more than 100 raw honey samples collected from different areas in Belgium, as well as some wax and bee samples, with a slightly adapted procedure.

Multiresidue analysis of pesticides in animal liver by gas chromatography using triple quadrupole tandem mass spectrometry

Two methods for extracting organochlorine (OCs) and organophosphorus (OPs) pesticides from animal liver have been developed. The determination was carried out by gas chromatography with electron impact ionization tandem mass spectrometry (GC-(EI-)MS/MS) using a triple quadrupole (QqQ) analyzer. First, a liquid-solid extraction performed with a high-speed homogenizer (Polytron) using ethyl acetate as solvent, and a subsequent clean-up by gel permeation chromatography (GPC) was applied, determining 34 pesticides. Secondly, a matrix solid phase dispersion (MSPD) extraction with octadecylsilyl (C(18)) sorbent combined with a Florisil clean-up and ethyl acetate elution was performed, analyzing 25 compounds. These methodologies have been tested and compared in the sample pre-treatment due to the fatty nature of the matrix. The GPC method was finally selected and validated, yielding recoveries in the range 70-115%, with precision values expressed as relative standard deviation (RSD) lower or equal to 20%, at the spiking levels of 25 and 50 microg kg(-1), and limits of quantification (LOQs) lower than the maximum residue levels (MRLs) set by the European Union in animal products, except for isofenphos. Linearity was also studied ranging between 5 and 300 microg kg(-1) for most of pesticides. This method was applied to the analysis of real liver samples of chicken, pork and lamb.

Current trends in solid-phase-based extraction techniques for the determination of pesticides in food and environment

Solid-phase extraction (SPE) procedures for pesticide residues in food and environment are reviewed and discussed. The use of these procedures, which include several approaches such as: matrix solid-phase dispersion (MSPD), solid-phase micro-extraction (SPME) and stir-bar sorptive extraction (SBSE), represents an opportunity to reduce analysis time, solvent consumption, and overall cost. SPE techniques differ from solvent extraction depending on the interactions between a sorbent and the pesticide. This interaction may be specific for a particular pesticide, as in the interaction with an immunosorbent, or non-specific, as in the way a number of different pesticides are adsorbed on apolar or polar materials. A variety of applications were classified according to the method applied: conventional SPE, SPME, hollow-fiber micro-extraction (HFME), MSPD and SBSE. Emphasis is placed on the multiresidue analysis of liquid and solid samples.

Comparison of matrix solid-phase dispersion and liquid–liquid extraction for the chromatographic determination of fenthion and its metabolites in olives and olive oils

Matrix solid-phase dispersion (MSPD) methodology has been developed to extract fenthion and its metabolites from olives and olive oils, and the technique compared with conventional liquid-liquid extraction (LLE). The method was applied to olives and olive oil samples obtained from olive groves treated with fenthion. Pesticide residues were analysed by gas chromatography (GC) using a nitrogen-phosphorus detector. Both extraction methods gave a linear response over the concentration range assayed (0.03-1 mg kg-1 for MSPD and 0.1-1 mg kg-1 for LLE). Recoveries and RSD (n = 6) values in olives were 85-112% and 2-6% for MSPD, and 68-108% and 4-16% for LLE, respectively. In the case of olive oil, recoveries and RSD (n = 6) values were 67-98% and 5-11% for MSPD, and 63-115% and 6-14% for LLE, respectively. When compared to LLE, the newly developed MSPD method was twice as sensitive and required 10 times less sample weight.

Development and validation of a multiresidue method for the analysis of 151 pesticide residues in strawberry by gas chromatography coupled to a triple quadrupole mass analyzer

A new method was developed and validated for the simultaneous determination of 151 pesticide residues in strawberry by gas chromatography coupled to a triple quadrupole mass analyzer (GC/QqQ-MS/MS), mainly using the selected reaction monitoring (SRM) mode. The list of target compounds included various classes of pesticides such as organochlorine (OCPs), organophosphorus (OPPs), carbamates, pyrethroids, triazoles and dicarboximides. A single extraction of 10 g of sample with acetonitrile followed by liquid-liquid partition formed by the addition of 4 g of MgSO4 and 1 g of NaCl was applied in sample preparation. Cleanup of the extracts was carried out by applying dispersive solid-phase extraction (D-SPE) with primary secondary amine (PSA). The analysis time was 21 min. The method was subjected to a thorough validation procedure. The recovery data were obtained by spiking blank samples at two concentration levels (11.5 and 50 microg/kg), yielding recoveries in the range 70-110%. Precision values expressed as relative standard deviation (RSD) were lower than 18% and 22% for the intraday and interday precision, respectively. Linearity was studied in the range 10-200 microg/kg and determination coefficients (R(2)) were higher than 0.98% for all compounds. Limits of detection (LODs) and limits of quantification (LOQs) were established as 4 and 10 microg/kg, respectively. The overall uncertainty of the method was estimated at two different concentrations (11.5 and 50 microg/kg), being lower than 25% in both cases. According to the validation data and performance characteristics as well as the high sample throughput and low cost, the proposed method is suitable for routine application.

A novel approach for simultaneous determination of 2-mercaptobenzimidazole and derivatives of 2-thiouracil in animal tissue by gas chromatography/mass spectrometry

A novel approach for determination of 2-mercaptobenzimidazole (MBI) and other thyreostatic residues in animal tissues by gas chromatography/mass spectrometry (GC/MS) in selected ion monitoring mode was developed. The analytes in animal tissues (including hypothyroid, pork muscle and beef samples) were extracted by acetonitrile, and then purified by a matrix solid-phase dispersion (MSPD) procedure after the extraction residues had been dissolved in water. The thyreostatic residues were derivatized by pentafluorobenzyl bromide (PFBBr) under strong basic conditions and then N-methyl-N-(trimethylsilyl)trifluoroacetamide (MSTFA) before GC/MS analysis. Different kinds of solid supports with various polarities for the MSPD procedure were investigated, and it was found that silica gel was suitable for the purpose. The average recoveries of the thyreostatic drugs in animal tissues ranged from 71.5-96.9% with the relative standard deviations below 10%. By using the developed method, the limits of detection were 10 microg/kg for MBI; 5 microg/kg for 6-phenyl-2-thiouracil; and 2 microg/kg for 2-thiouracil, 6-methyl-2-thiouracil and 6-propyl-2-thiouracil. The stability of the thyreostatic drugs in spiked animal tissues was tested, and the results showed that the thyreostatic drugs did not decompose within 3 months if the sample was stored in darkness below -20 degrees C.

Application of matrix solid-phase dispersion and liquid chromatography–mass spectrometry to fungicide residue analysis in fruits and vegetables

A method based on matrix solid-phase dispersion (MSPD) and liquid chromatography-electrospay ionization-mass spectrometry used to analyze fifteen fungicide residues in fruits and vegetables is described. The method required only 0.5 g of sample, C(18)-bonded silica was used as dispersant sorbent, and ethyl acetate was used as eluting solvent. Fortified recoveries in apple, orange, banana, lettuce, grape and tomato samples ranged from 71% to 102% and relative standard deviations were less than 13% with fortified levels of 0.03-1.5 mg kg(-1). Detection and quantification limits were 1 approximately 30 microg kg(-1) and 4 approximately 100 microg kg(-1), respectively, with linear calibration curves extending up to 15 mg kg(-1). The analytical characteristics of MSPD compared very favorably with those found for a classical multiresidue method: the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method. The method was applied to determine the fungicides in real samples. Liquid chromatography-tandem mass spectrometry (LC-MS-MS) was used as confirmatory tool for positive samples.

Method of analysis of a selected group of pyrethroids in soil samples using off-line flow-through extraction and on-column direct large-volume injection in reversed phase high performance liquid chromatography

An analytical method using flow-through extraction of a soil sample filled in a short HPLC column with methanol or methanol-water mixtures and large-volume injection in RP-HPLC has been developed for the simultaneous determination of residues of three pyrethroids--kadethrin, cypermethrin, and permethrin--from soil samples. The developed RP-HPLC method enables separation of four diastereoisomers of cypermethrin into three peaks and resolution of two diastereoisomers of permethrin. The UV photometric detection limits of direct on-column large-volume injection of 1.00 mL of extract were 30 ng/mL of kadethrin, 37 ng/mL of total content of cypermethrin, and 65 ng/mL of trans-permethrin, which corresponds to a pyrethroid soil content of around 0.3 mg/kg. Effects of extractant flow rate and optimal extractant volume on the percentage recovery of pyrethroids from Slovak soil samples were studied. Recovery studies were performed at 0.5- 5.0 microg/g fortification level of kadethrin and 1.0-2.5 microg/g fortification level of cypermethrin and permethrin in a soil sample. Recoveries ranged from 83 to 90% for kadethrin, from 87 to 94% for total cypermethrin, and from 85 to 98% for trans-permethrin. This work comprises a basic study aimed at elaboration of an RP-HPLC method of direct analysis of pyrethroids in a soil matrix at low concentration levels achieved by a "solid sample injection" in HPLC--on-line interfacing of analyte extraction, extract clean-up, and analysis.

Application of sample disruption methods in the extraction of anthocyanins from solid or semi-solid vegetable samples

Cassis, a commercial powder obtained from blackcurrant juice (Ribes nigrum L.), was used to optimize the anthocyanin extraction by matrix solid-phase dispersion (MSPD) and by sea sand disruption method (SSDM). The optimum eluent conditions were 5.0 mL of MeOH/H2O (1:1, v/v) at pH 2. The extracts were analyzed by HPLC with diode-array detection (DAD) and the extraction efficiency was evaluated by statistical comparison (analysis of variance, ANOVA-single factor) of the compounds peak areas. The extraction efficiency for the MSPD procedure was dependent on the chemical nature of the C18 material but the optimized procedure yielded results similar to those obtained by the inexpensive sea sand disruption method (SSDM). This procedure also compared favorably to a previously published liquid-liquid extraction method. The optimized sea sand method was then used in the anthocyanin extraction from red grapes (Vitis vinifera L.) and strawberries (Fragaria ananassa D.) yielding chromatographic profiles similar to those reported in the literature for these products.