Extracellular polymer substances and physicochemical properties of flocs in steady and unsteady-state activated sludge systems

Nutrient removal and microalgal biomass production on urine in a short light-path photobioreactor

Due to the high nitrogen and phosphorus content, source-separated urine can serve as a major nutrient source for microalgae production. The aim of this study was to evaluate the nutrient removal rate and the biomass production rate of Chlorella sorokiniana being grown continuously in urine employing a short light-path photobioreactor. The results demonstrated, for the first time, the possibility of continuous microalgae cultivation in human urine. The lowest dilution factor successfully employed was a factor of 2 (50% v/v urine). Microalgae dominated a smaller bacterial population and were responsible for more than 90% of total nitrogen and phosphorus removal. With a light-path of 10 mm, a maximum volumetric biomass productivity as high as 9.3 g L(-1) d(-1) was achieved. The co-existing bacterial population removed up to 70% of organic pollutants from the urine at a rate of 1300 mg COD L(-1) d(-1). Enriching the urine with magnesium, adjusting the N:P molar ratio, and shortening the reactor light-path further increased the volumetric biomass productivity to 14.8 g L(-1) d(-1). The corresponding nitrogen and phosphorus removal rates were 1300 and 150 mg L(-1) d(-1), respectively. The subsequently produced biomass contained 43-53% w/w proteins and 16-25% w/w total fatty acids.

Rheology measurements for online monitoring of solids in activated sludge reactors of municipal wastewater treatment plant

Rheological behaviour of recycled sludge from a secondary clarifier of a municipal wastewater treatment plant was studied by using the rate controlled coaxial cylinder viscometer Rotovisko-Haake 20, system M5-osc., measuring device NV. The tests (hysteresis cycles) were performed under continuous flow conditions and following an ad hoc measurement protocol. Sludge shear stress versus shear rate curves were fitted very satisfactorily by rheological models. An experimental equation correlating the solid concentration of sludge to relative viscosity and fitting satisfactorily flow curves at different Total Suspended Solids (TTS%) was obtained. Application of the empirical correlation should allow the monitoring of the proper functioning of a wastewater treatment plant measuring viscosity of sludge.

Dynamics of intracellular polymers in enhanced biological phosphorus removal processes under different organic carbon concentrations

Enhanced biological phosphorus removal (EBPR) may deteriorate or fail during low organic carbon loading periods. Polyphosphate accumulating organisms (PAOs) in EBPR were acclimated under both high and low organic carbon conditions, and then dynamics of polymers in typical cycles, anaerobic conditions with excess organic carbons, and endogenous respiration conditions were examined. After long-term acclimation, it was found that organic loading rates did not affect the yield of PAOs and the applied low organic carbon concentrations were advantageous for the enrichment of PAOs. A low influent organic carbon concentration induced a high production of extracellular carbohydrate. During both anaerobic and aerobic endogenous respirations, when glycogen decreased to around 80 ± 10 mg C per gram of volatile suspended solids, PAOs began to utilize polyphosphate significantly. Regressed by the first-order reaction model, glycogen possessed the highest degradation rate and then was followed by polyphosphate, while biomass decay had the lowest degradation rate.

Effect of exo-polysaccharide concentration in the rheological properties and settling ability of activated sludge

The non-Newtonian properties of activated sludge (AS) suspension lead to transfer limitations (oxygen, substrate...) and operation difficulties in Waste Water Treatment Plants (WWTP). The current approach involves assuming the sludge behaves like water on a rheological point of view, and then oversizing pumping and aeration devices, which represent over 60% of the operating cost in WWTP. The objective of this work is to understand the effect of bioflocculation on the rheological properties and the settling ability of AS suspensions, by means of variations in concentration of exo-cellular polysaccharides. Experiments have been conducted in a 20 L laboratory scale bioreactor at a constant retention time of 20 days and with a total suspended solid concentration between 15 and 20 g L(-1). The bioreactor was fed with a synthetic substrate at a constant mass loading rate of 0.3 kg(DCO) kg(-1)(TSS) d(-1). Our results show that increasing the exo-polysaccharide (EPS) concentration from 10 to 80 mg g(-1)(TSS) leads to an increase in shear-thinning properties of AS. An improvement of the settling ability is also obtained, at least when the EPSs increase from 10 to 45 mg g(-1)(TSS). Above 45 mg g(-1)(TSS) of adsorbed polysaccharides, the settling ability seems to decrease again.

Nitrification performance in a membrane bioreactor treating industrial wastewater

The influence of industrial (pharmaceutical and chemical) wastewater composition on membrane bioreactor (MBR) performance was investigated in a pilot-scale installation. The study focussed on nitrification performance, which was evaluated based on influent and effluent parameters as well as batch nitrification rate tests. The industrial wastewater was pumped into the MBR in a mixture with municipal wastewater at constant flow rate. The loading of the MBR with industrial wastewater was increased stepwise from 0 to 75% share in the mixed influent to study the adaptation of nitrifying bacteria. Stable nitrification performance was observed until the content of industrial wastewater in the influent reached 40%, with effluent values of around 0.56 mg L(-1) NH4-N and 98.3% ammonia removal. Breakdown of nitratation was observed at a 40% industrial wastewater dose and breakdown of nitritation at a 50% dose, respectively. However, after several months of adaptation, both processes recovered. No nitrification was observed when the industrial wastewater share exceeded 50%. Adaptation of nitrifying bacteria in the MBR was also confirmed by results of kinetic tests. The inhibition effect of the concentrated industrial wastewater to the MBR sludge decreased substantially after several months of exposure, while the inhibition of referential activated sludge remained constant.

Impact of oxygen cut off and starvation conditions on biological activity and physico-chemical properties of activated sludge

Physico-chemical and biological parameters were monitored both throughout different oxygen cut off and starvation (OCS) times (6 h-72 h) and after the restoration of normal operational conditions. Sludge apparent viscosity and soluble extracellular polymeric substances (EPS) characteristics were measured to determine the activated sludge (AS) properties. Oxygen transfer, biological activity with specific oxygen uptake rate (SOUR) measurements during endogenous/exogenous conditions (without any external substrate/with external substrate consumption) and chemical oxygen demand (COD) removal were measured to assess the AS performances. During the different stress times, AS deflocculated as a decrease of apparent viscosity was observed and microorganisms biodegraded the released EPS to survive. After aeration return, and under endogenous conditions, size exclusion chromatographic fingerprints of soluble EPS were modified and macromolecules probably of type humic-like substances appeared in significant quantities. These new macromolecules presumably acted as biosurfactants. Consequently, the liquid surface tension, as well as the oxygen transfer rate (OTR), decreased. Under exogenous conditions, high biological activity (SOUR = 11.8 +/- 2.1 mg(O2 x g(MLVSS)(-1) x h(-1)) compensated the decrease of oxygen transfer. Finally, AS biomass maintained a constant COD degradation rate (15.7 +/- 1.9 mg(O2) x g(MLVSS)(-1) x h(-1)) before and after the disturbances for all times tested. This work demonstrates that AS microorganisms can counteract concomitant oxygen and nutrients shortage when the duration of such a condition does not exceed 72 h. Dissociation of endogenous/exogenous conditions appears to offer an ideal laboratory model to study EPS and biomass activity effects on oxygen transfer.

Fluorescence detection to determine proteins and humic-like substances fingerprints of exopolymeric substances (EPS) from biological sludges performed by size exclusion chromatography (SEC)

Fingerprints of extracellular polymeric substances (EPS) from activated and anaerobic granular sludges were obtained by size exclusion chromatography coupled to UV (210 and 280 nm) and fluorescence (221/350 nm (protein-like molecules) and 345/443 nm (humic-like substances)) detection. The total area below the peaks obtained with fluorescence detection is linked to the protein or humic-like substances EPS content. The EPS protein fingerprints, usually recorded with UV-280 nm, change dramatically, mainly in the relative size of peaks when they were measured by a florescence detection method. It means that the apparent molecular weight (aMW) distribution of EPS chomatophores and fluorophores is different. Protein-like and humic-like substances were found to be specific fingerprints of the EPS, affected by the type and origin of the bacterial aggregate and improve EPS sample differentiation. The protein-like fraction of EPS displays a wide range of aMW (>600 kDa-<10 kDa) whereas the humic-like substances fraction is composed of molecules of low aMW (6-<1.2 kDa).

Influence of extraction method on size exclusion chromatography fingerprints of EPS from wastewater sludges

Extracellular polymeric substances (EPS) were separated using two serial-linked size exclusion chromatography (SEC) columns to obtain detailed fingerprints. The chromatographic profile results were influenced by the nature of biological sludge (activated sludges, anaerobic granules, anaerobic flocculated sludges). Furthermore, our results highlight that EPS fingerprints are also highly dependent on the extraction method. If physical extractions modify only the relative absorbance of the chromatographic peaks, heating during extraction induces significant modifications of the fingerprints, probably owing to better organic matter extraction efficiency as well as an increase in hydrolysis for some compounds but not for EPS extracted from anaerobic granular sludges. This confirms that thermal treatment is a proper method to extract EPS from anaerobic granular sludges. The use of chemical extraction results in major changes on the EPS fingerprints. This work demonstrates that some chromatographic peaks are due to residues from the chemical reagent (such as EDTA, glutaraldehyde) which can modify or form complexes with some EPS macromolecules. As a result, due to its sensitivity to sludge origin and/or extraction procedure, SEC appears to be a suitable tool for an accurate qualitative EPS characterization.

A mini-review on membrane fouling

During the last decades, the interest of using membrane technology has emerged in wastewater treatment as well as drinking water and process water production. However, the impediment of the membrane technology is the fouling problem and consequently higher operating and membrane replacement cost. Hence, better understanding of membrane fouling is not only the key to solve the problems, but also is one of the main factors driving membrane technology forward. This mini-review paper identifies the major foulants and the principal membrane fouling mechanisms such as pore blocking, cake formation, concentration polarization, organic adsorption, inorganic precipitation and biological fouling. It also gives a holistic review about different fouling phenomena during the application of membrane separation technologies in water and wastewater treatment, with specific references to various problems, membranes, treatment processes and its practical applications.

Effect of cyclic aeration on fouling in submerged membrane bioreactor for wastewater treatment

Due to the inefficiency of aeration measures in preventing fouling by soluble and colloidal particles. The effect of alternating high/low cyclic aeration mode on the membrane fouling in the submerged membrane bioreactor was studied by comparing to fouling in a constant aeration mode. Results indicated a higher overall fouling rate in the cyclic aeration mode than in the constant aeration. However, a higher percentage of reversible fouling was observed for the cyclic aeration mode. The membrane permeability can be more easily recovered from physical cleaning such as backwashing in the cyclic aeration mode. The activated sludge floc size distribution analysis revealed a floc destruction and re-flocculation processes caused by the alternating high/low aeration. The short high aeration period could prevent the destruction of strong strength bonds within activated sludge flocs. Therefore, less soluble and colloidal material was observed in the supernatant due to the preservation of the strong strength bonds. The weak strength bonds damaged in the high aeration period could be recovered in the re-flocculation process in the low aeration period. The floc destruction and re-flocculation processes were suggested to be the main reason for the low irreversible fouling in the cyclic aeration mode.

Qualitative characterization of the protein fraction of exopolymeric substances (EPS) extracted with EDTA from sludge

Exopolymeric substances (EPS) were extracted by EDTA from activated and anaerobic granular sludge. Due to the presence of EDTA in EPS extract, interferences were pointed out for the characterization of EPS by means of the colorimetric methods and fluorescence spectroscopy. Other methods have been investigated to characterize the EPS protein fraction. Size exclusion chromatography (SEC), performed at a fluorescence excitation-emission matrix of 221/360 nm (tryptophan protein-like substances) for detection, was suitable and allowed obtaining a fingerprint of the protein-like substance fractions and determining apparent molecular weight (MW). Polyacrylamide gel electrophoresis (PAGE) was performed under either native or denaturing conditions. Various staining applications after EPS migration are effective in obtaining a protein (silver staining) or glycoprotein (PAS staining) fingerprint or MW distribution. SEC and PAGE are both appropriate techniques for the qualitative characterization of protein fractions from EPS extracted by EDTA and moreover differentiate EPS according to sludge origin and type.

The population dynamics of nitrifiers in ammonium-rich systems

Non-optimal pH, dissolved oxygen concentration, the presence of toxic substances, or the influence of grazers are known to cause disturbances in nitrification. Because activated sludge is a mixture of different organisms, bacteria, and higher organisms, the stability of processes such as carbon removal, nitrification, denitrification, and dephosphatation depends on a range of interactions. These interactions occur both between and within trophic levels. Understanding of the ecology of microorganisms involved in bioprocesses is essential for effective control of startup and operation of a particular process. The aim of the study was to gain further insight into the dynamics of nitrifiers in activated sludge at various sludge ages while treating higher concentrations of ammonium. The results confirmed the importance of Nitrosococcus mobilis and Nitrobacter sp. as the dominant nitrifiers responsible for nitritation and nitratation, respectively, in the presence of unlimited ammonium. The size of the dominant bacteria colony was larger compared to the other species present and reached 25 microm. Problems with nitrification occurred in all high-ammonium loaded reactors. The dynamics of nitrifier population was monitored by oxygen uptake rate (OUR) using a test enabling the OUR measurement separately for ammonium-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB). The results reveal the hypersensitivity of nitrifiers to the substrate and products of incomplete nitrification.

Fate of hazardous aromatic substances in membrane bioreactors

In this work, the removal of hazardous aromatic compounds was investigated in two types of membrane bioreactors (MBRs), based on cross-flow and semi dead-end filtration systems. BTEX and PAH were efficiently eliminated from wastewater during treatment via a membrane bioreactor (90-99.9%) but non-biotic processes, i.e. volatilisation and sorption, contributed significantly. The semi dead-end MBR showed slightly better removal efficiencies than the cross-flow MBR. However, non-biotic processes were more significant in the first process and, finally, degradation rates were higher in the cross-flow MBR. Higher degradation rates were explained by a higher bio-availability of pollutants. Differences in shear stress imposed in cross-flow and semi dead-end filtration systems radically modify the sludge morphology. High shear stress (cross-flow filtration) generates dispersed bacteria and larger quantities of dissolved and colloidal matter. Sorption of hydrophobic compounds (PAHs) on suspended solid was less marked in disaggregated sludge. The results suggest new strategies for improving micro-pollutant degradation in MBRs.

Characterisation of the mineral fraction in extracellular polymeric substances (EPS) from activated sludges extracted by eight different methods

This work characterises the mineral fraction of EPS extracts obtained using eight different methods from two activated sludges by total mineral content determination, Fourier Transformed Infrared spectrometry and with scanning electron microscopy coupled with an EDX probe. Despite EPS dialysis, the EPS extracts displayed a mineral fraction between 2% and 40% of the EPS dry weight depending on the extraction method used. The main mineral elements found in the EPS extract were Ca, Mg, Na, K, Al, Fe, Mn, P, Si and S, but their contents were strongly affected by the extraction method used. Some of the minerals are associated with the organic molecules within the EPS. The presence of mineral particles of various compositions and structures (clays, quartz or carbonate) in the EPS extract with a wide range in size was clearly demonstrated. Moreover, the association of metallic elements with the mineral particles in the EPS extract was highlighted.

Effect of C/N ratio on extracellular polymeric substances (EPS) and physicochemical properties of activated sludge flocs

The influences of C/N ratio on the extracellular polymeric substances (EPS) and physicochemical properties of the activated sludge flocs were investigated using laboratory-scale sequencing batch reactors (SBRs). Flocs sizes decreased when C/N ratio increased from 20 to 100 and decreased from 20 to 4. The amount of total EPS, TB-EPS, and the carbohydrate and protein contents in TB-EPS were independent of the C/N ratio. In LB-EPS, the protein content increased and the carbohydrate content decreased at decreased C/N ratio, whereas the protein content decreased and the carbohydrate content increased at increased C/N ratio. Effluent suspended solids (ESS) content, turbidity, sludge volume index (SVI), capillary suction time (CST), and specific resistance to filtration (SRF) increased when the C/N ratio decreased, indicating poor flocculation, settleability and dewaterability of the flocs. However, when the C/N ratio increased, only ESS content, SVI and CST value increased. These properties of the flocs were deteriorated greatly under decreased C/N ratio as compared to increased C/N ratio. The characteristics of the flocs could be recovered when C/N ratio returned to the original value. Only the content of protein in LB-EPS was positively correlated with the flocculation, settleability and dewaterability of the flocs.

Adsorption of nitrobenzene from aqueous solution on activated sludge modified by cetyltrimethylammonium bromide

A novel method was conducted to modify activated sludge with cetyltrimethylammonium bromide (CB) to obtain an adsorbent to remove aqueous nitrobenzene. The adsorption characteristics of nitrobenzene onto modified activated sludge (MAS) were investigated, by contrast with those of unmodified activated sludge (UMAS). Nitrobenzene adsorption onto MAS is more favorable than that of UMAS at initial nitrobenzene concentrations below 150 mg/L, above which they have an equivalent adsorption capacity. pH value has a significant influence on the adsorption capacity, especially from 10.0 to 12.6 for MAS and from 9.0 to 11.0 for UMAS. The modification changes the steady even surface of activated sludge into uneven one, which is better for adsorption. The hydroxyl of activated sludge and hydrophobic group of CB adsorb nitrobenzene molecules, and CB increases the adsorption sites. The nitrobenzene adsorption onto MAS follows Langmuir isotherm, implying the adsorption occurrence tends to be on a homogeneous surface by monolayer adsorption other than multi-layer adsorption which accounts for the adsorption onto UMAS. The maximum adsorption capacity of MAS is 40.6, 25.0 and 25.6 mg/g at 6.0, 25.0 and 40.0°C, respectively. MAS presents to be a good adsorbent to remove nitrobenzene from water, and CB is a successful modifier.

Influence of sludge discharge on sludge settleability and membrane flux in a membrane bioreactor

In this study, the correlations between sludge characteristics, amount of extracellular polymeric substances (EPS) and membrane fouling were investigated and analysed, using continuous sludge discharges from a membrane bioreactor (MBR). The results showed that continuous sludge discharges improved sludge settleability, but not always weakened membrane fouling. The changes in the EPS amount, caused by continuous sludge discharge from MBRs, could resolve this situation well. Soluble EPS concentration could be regulated, to some extent, by sludge discharges. But it was embarrassed to artificially adjust bound EPS amount because the MBRs included living microorganisms and their metabolites. After sludge had been discharged four times, the sludge volume index (SVI) was in the range of 50-60 mL x gSS(-1) with a VSS:SS ratio of about 0.8. Sludge settleability mainly depended on the bound EPS content. The bound EPS content and its components presented a closer relationship to sludge hydrophobicity than to the membrane flux. Soluble EPS dominated both the EPS content on the membrane surface and membrane fouling.

Extracellular polymeric substances (EPS) of microbial aggregates in biological wastewater treatment systems: a review

A review concerning the definition, extraction, characterization, production and functions of extracellular polymeric substances (EPS) of microbial aggregates in biological wastewater treatment reactors is given in this paper. EPS are a complex high-molecular-weight mixture of polymers excreted by microorganisms, produced from cell lysis and adsorbed organic matter from wastewater. They are a major component in microbial aggregates for keeping them together in a three-dimensional matrix. Their characteristics (e.g., adsorption abilities, biodegradability and hydrophilicity/hydrophobicity) and the contents of the main components (e.g., carbohydrates, proteins, humic substances and nucleic acids) in EPS are found to crucially affect the properties of microbial aggregates, such as mass transfer, surface characteristics, adsorption ability, stability, the formation of microbial aggregates etc. However, as EPS are very complex, the knowledge regarding EPS is far from complete and much work is still required to fully understand their precise roles in the biological treatment process.

Submerged membrane bioreactor at substrate-limited conditions: activity and biomass characteristics

A pilot-scale membrane bioreactor was operated for advanced treatment of secondary effluent from a wastewater treatment plant. The performance and biomass characteristics were evaluated under two different hydraulic retention time (HRT) values (7.5 and 15 hours). The system was operated successfully without biomass purge and, after an initial phase, evolved until reaching a constant mixed-liquor volatile suspended solids (MLVSS) concentration, which resulted in the same value of carbon utilization rate (0.067 +/- 0.004 kg COD kg(-1) MLVSS d(-1)) for both HRTs. Respiration tests (maximum and endogenous oxygen uptake rates) confirmed a low microbial activity, which approached constant values (0.32 +/- 0.001 and 0.064 +/- 0.007 g O2 g(-1) MLVSS d(-1), respectively), regardless of the HRT. The sludge morphology and bound and supernatant extracellular polymeric substances also were assessed. Membrane performance was characterized by a stable behavior occurring simultaneously with a high level of biodegradation in the microcolloidal and soluble fraction.

Evaluation of size exclusion chromatography (SEC) for the characterization of extracellular polymeric substances (EPS) in anaerobic granular sludges

The extracellular polymeric substances (EPS) extracted from three granular and one flocculant anaerobic sludges were characterised by size exclusion chromatography (SEC) using two serially linked chromatographic columns in order to obtain more detailed chromatograms. A Superdex peptide 10/300 GL (0.1-7 kDa) and Superdex 20010/300 GL (10-600 kDa) from Amersham Biosciences were used in series with a mobile phase at pH 7 with an ionic strength of 0.223 M (phosphate buffer 50 mM and NaCl 150 mM). A part of the EPS molecules displays hydrophobic and/or ionic interactions with the column packing. Interactions could be modified by changing the mobile phase ionic strength or polarity (addition of acetonitrile). The detection wavelength (210 or 280 nm) affects strongly the EPS chromatogram. For a sludge originating from the same type of biofilms (i.e., anaerobic granules), the differences in EPS fingerprints are mainly due to differences in the absorbance of the chromatographic peaks, linked to EPS molecules content and composition. The EPS fingerprint changes significantly when the EPS originate from another type of anaerobic sludges. In addition, EPS fingerprints were affected by the extraction method used (centrifugation only; heat and centrifugation or cationic exchange resin and centrifugation). This phenomenon was observed mainly for the largest and smallest molecules and molecules which display interactions with column packing.

Sorption of Cd(II) and Pb(II) by exopolymeric substances (EPS) extracted from activated sludges and pure bacterial strains: modeling of the metal/ligand ratio effect and role of the mineral fraction

The present study deals with the sorption of Cd(II) and Pb(II) by exopolymeric substances (EPS) extracted from activated sludges or pure bacterial strains. The percentage of sorbed metal increases with the concentration of the EPS-water solution. Pb(II) always presents a higher affinity than Cd(II) for EPS. For the EPS extracted from pure bacterial strains, only one global binding constant from a simple equilibrium sorption model, may be used to assess the effect of microbial products such as EPS on Cd(II) and Pb(II) speciation or mobility in the environment. However, for EPS extracted from activated sludges, the wide variation of the global binding constants determined for Cd(II) and Pb(II) do not permit such a simple approach. The differences in sorption to metals between the two types of EPS (bacterial, activated sludges) could be explained by the differences in EPS composition: organic macromolecules, as well as the nature of the mineral fraction.

Application of chemical precipitation and membrane bioreactor hybrid process for piggery wastewater treatment

This study was conducted to investigate the chemical precipitation (CP) and membrane bioreactor (MBR) hybrid process for the treatment of piggery wastewater. Average removal efficiencies for BOD, COD and turbidity in CP process were 64.3%, 77.3% and 96.4%, respectively. CP process had a moderate effect on NH(3)-N removal (40.4%) which improved up to 98.2% mainly due to nitrification and filtration processes in MBR. The average removal efficiencies of BOD, COD and turbidity in MBR were 99.5%, 99.4% and 99.8%, respectively. Monod equation was used to explain the microbial activities in terms of specific growth rate. The specific growth rate of bacteria in aeration tank (N-batch) and anoxic tank (D-batch) were 0.013 and 0.005d(-1) with a biomass yield of 0.78 and 0.43mg MLSS produced/mg COD utilized, respectively. Microorganisms from the N-batch and D-batch showed a low-level of nitrifying and moderate-level of denitrifying capabilities which were 1.08mg NH(3)-N/(g MLVSS.h) and 2.82mg NO(3)-N/(g MLVSS.h), respectively. Carbohydrates were the main component in extracellular polymeric substance (EPS) compounds that could be attached to the membrane surface easily and led to membrane biofouling. The increase of MLSS, EPS and sludge viscosity concentration, decrease of sludge floc size and incomplete chemical cleaning procedure resulted in the increase of membrane resistance. Total membrane resistance increased from 3.19x10(12)m(-1) to 5.43x10(14)m(-1).

A high yield multi-method extraction protocol for protein quantification in activated sludge

A multi-method extraction protocol based on mechanical, ionic and hydrophobic methods was investigated on two types of activated sludge samples. Extraction methods were chosen with regards to optimal protein yield without cell disruption. Sonication, EDTA and Tween extraction methods were selected and combined. The total amount of protein released by the multi-method protocol sums up to 191 and 264 mg equiv. BSA/g VSS for the two different sludge samples. Protocol repetition on the same sample showed that protein yield after each successive protocol fitted an exponential curve model. The total amount of extractable proteins was evaluated by model predictions, 423 and 516 mg equiv. BSA/g VSS for the two sludge samples. The multi-method extraction protocol appears relevant for harvesting a representative quantity of proteins from the original sample (45-49%), moreover the multi-method criterion of the protocol also offers a heterogeneous pool of proteins. Thus, further qualitative studies may not be biased by the extraction protocol.

Lead and cadmium biosorption by extracellular polymeric substances (EPS) extracted from activated sludges: pH-sorption edge tests and mathematical equilibrium modelling

The sorption of Cd and Pb by extracellular polymeric substances (EPS) extracted from activated sludges originated from wastewater treatment plants (WWTPs) or Lab-scale bioreactors was investigated as a function of pH. The study was carried out using a polarographic method in the SMDE (stripping mercury dropping electrode) mode which is suited to determine labile metals in solution containing soluble ligands such as EPS. The results obtained provide evidence of the presence of a pH-sorption/desorption edge for Cd and Pb by EPS. The use of Kurbatov's model gives information on the mechanisms involved through the determination of "relative complexation constants" (operationally defined) and the number of protons exchanged. The use of this model demonstrates that proton exchange with metals is not the only mechanism involved in metal biosorption by EPS. Other mechanisms such as cation exchange with Ca or Mg, global electric field surrounding the ligand or micro-precipitation of metals could be involved in metal sorption by EPS. The position of the pH-sorption edge curves and the "relative complexation constants" show that Pb displays a greater affinity for EPS than Cd. The studied EPS have large differences regarding binding strength of Cd and Pb. These differences are not correlated with the organic parameters measured to characterize the EPS, however the mineral fraction of the EPS could be involved to a large extent in the sorption of metal.

Influence of different substrates on the formation and characteristics of aerobic granules in sequencing batch reactors

The effects of different substrates on the aerobic granulation process were studied using laboratory-scale sequencing batch reactors (SBRs). Four parallel granules sequencing batch reactors (GSBR): R1, R2, R3, and R4 were fed with acetate, glucose, peptone and fecula, respectively. Stable aerobic granules were successfully cultivated in R1, R2, R4, and smaller granules less than 500 microm were formed in R3. Morphology and the physic-chemical characteristics of aerobic granules fed with different carbon substrates were investigated by the four reactors operated under the same pressure. The aerobic granules in the four reactors were observed and found that peptone was the most stable one due to its good settleability even after a sludge age as short as 10 d. A strong correlation was testified between the characteristics of aerobic granules and the properties of carbon substrates. The stability of aerobic granules was affected by extracellular polymer substances (EPS) derived from microorganism growth during feast time fed with different carbon substrates, and the influence of the property of storage substance was greater than that of its quantity. Optimal carbon substrates, which are helpful in the cultivation and retention of well-settling granules and in the enhancement of the overall ability of the aerobic granules reactors, were found.

Comparative study of laboratory-scale thermophilic and mesophilic activated sludge processes

Laboratory-scale mesophilic (20-35 degrees C) and thermophilic (55 degrees C) activated sludge processes (ASPs) treating diluted molasses wastewater were compared in effluent quality, removal of different COD fractions, sludge yield, floc size, and sludge settleability. The effect of polyaluminium chloride (PAC) with high cationic charge on sludge settleability and effluent quality was also studied. In the ASPs, the hydraulic retention time was 12h in both processes, corresponding to a volumetric loading rate of 3.2+/-1.0 kg COD(filt) m(-3)d(-1). The mesophilic ASP gave 79+/-18% and 90+/-2% and the thermophilic ASP gave 50+/-6% and 67+/-11% total COD (COD(tot)) and GF/A-filtered COD (COD(filt)) removals, respectively. The higher COD values in the thermophilic effluent were due to dispersed particles, such as free bacteria, measured as colloidal COD (COD(col)=difference between soluble COD (COD(sol)) and COD(filt)). Both ASPs gave high (90%) COD(sol) removals. Aeration (24-h) of the thermophilic ASP effluent at 35 degrees C reduced the density of the free bacteria by half, which was also measured as 90% COD(col) removal. Post-aeration of thermophilic effluent at 55 degrees C had no influence either on the density of free bacteria or on the COD(col) values. The use of PAC did not increase COD(tot) or COD(filt) removals in either process, but reduced the mesophilic and increased the thermophilic sludge volume index values.

Production of extracellular polymeric substances in anoxic/oxic process with zeolite carriers for nitrogen removal

During the hydraulic retention time (HRT) from 12 to 6 h, the production of extracellular polymeric substance (EPS) decreased from 82 to 70 EPS mg volatile suspended solids (VSS) g(-1) in an anoxic/oxic (A/O) reactor with zeolite carriers. Added zeolite could successfully control the EPS production by the formation of stable biofilm and the maintenance the lower chemical oxygen demand/ammonium (C/N) ratio on its surface.