Electroosmotic properties of microfluidic channels composed of poly(dimethylsiloxane)

The effects of shear stress on isolated receptor-ligand interactions of Staphylococcus epidermidis and human plasma fibrinogen using molecularly patterned microfluidics

Staphylococcus epidermidis is an opportunistic pathogen that has been implicated in hospital-acquired infections, specifically related to implanted intravascular devices. S. epidermidis adhesion is a mechanism of colonization, leading to pathogenesis. Here we demonstrate an easily fabricated and robust parallel microfluidic platform to investigate the physiologically-relevant effects of fluid shear on S. epidermidis adhesion to human fibrinogen (hFg) with increased experimental throughput. In situ molecular patterning using fluid flow boundaries allows for isolation of the molecular interactions in highly defined shear stress environments, while keeping the device operation simple and reproducible. We characterize two modes of attachment of S. epidermidis to hFg coated surfaces. Single colonies adhere in high fractions at low shear stresses (~1 dyne cm(-2)) and adhesion decays with increasing shear. However, clusters of bacteria adhere the highest at median wall shear stress (up to 10 dyne cm(-2)), and adhesion subsequently decays above this critical shear stress. This initial characterization suggests a previously unobserved phenomenon of shear activated cell-cell adhesion in S. epidermidis, which acts to increase the overall attachment strength to hFg. Both of these modes of attachment are dependant upon the presence of intact hFg, indicating that adhesion is resultant from specific molecular recognition between the bacteria and human fibrinogen. This platform provides new insight into complex host-pathogen interactions, and will allow for further investigation of colonization and pathogenesis in more physiologically relevant conditions.

Detection of immunoglobulins in a laser induced fluorescence system utilizing polydimethysiloxane microchips with advanced surface and optical properties

We developed an automated laser induced fluorescence system utilizing microfluidic chips for detection and quantification of immunoglobulins. Microchips were fabricated from polydimethysiloxane (PDMS) using the so-called "prepolymerization technique." The microchip structure helped minimize the effects of PDMS autofluorescence and light scattering. Furthermore, a thin and uniform PDMS layer forming the top of the microchip enabled proper focusing and collection of the excitation beam and the emitted fluorescence, respectively. The developed system was tested for the detection of mouse immunoglobulins. The capturing antibodies were immobilized on internal microchannel walls in the form of a polyelectrolyte. We clearly show that this immobilization technique, if correctly realized, gives results with high reproducibility. After sample incubation and washing, secondary antibodies labeled by fluorescein isothiocyanate were introduced into microchannels to build a detectable complex. We show that mouse antibodies can be quantified in a wide concentration range, 0.01-100 μg ml(-1). The lower detection limit was below 0.001 μg ml(-1) (6.7 pM). The developed laser induced fluorescence (LIF) apparatus is relatively cheap and easy to construct. The total cost of the developed LIF detector is lower than a typical price of plate readers. If compared to classical ELISA (enzyme linked immunosorbent assay) plate systems, the detection of immunoglobulins or other proteins in the developed PDMS microfluidic device brings other important benefits such as reduced time demands (10 min incubation) and low reagent consumption (less than 1 μl). The cost of the developed PDMS chips is comparable with the price of commercial ELISA plates. The main troubleshooting related to the apparatus development is also discussed in order to help potential constructors.

Simple surface modification of poly(dimethylsiloxane) for DNA hybridization

Here, we present a simple chemical modification of poly(dimethylsiloxane) (PDMS) by curing a mixture of 2 wt% undecylenic acid (UDA) in PDMS prepolymer on a gold-coated glass slide. This gold slide had been previously pretreated with a self-assembled hydrophilic monolayer of 3-mercaptopropionic acid (MPA). During curing of the UDA∕PDMS prepolymer, the hydrophilic UDA carboxyl moieties diffuses toward the hydrophilic MPA carboxyl moieties on the gold surface. This diffusion of the UDA within the PDMS prepolymer to the surface is a direct result of surface energy minimization. Once completely cured, the PDMS is peeled off the gold substrate, thereby exposing the interfacial carboxyl groups. These groups are then available for subsequent attachment of 5(')-amino terminated DNA oligonucleotides via amide linkages. Our results show that the covalently tethered oligonucleotides can successfully capture fluorescein-labeled complementary oligonucleotides via hybridization, which are visualized using fluorescence microscopy.

Sodium hydroxide treatment of PDMS based microfluidic devices

We discuss the use of aqueous NaOH as a facile surface treatment method to control the electroosmotic flow in PDMS microchannels. Flushing of PDMS/PDMS and glass/PDMS microchannels with 1 M NaOH for 24 h leads to a doubling of the electroosmotic flow. This high flow rate is comparable to the flow rates achieved by treating PDMS microchannels with O2 plasma. Contact angle measurements and ATR-FTIR analysis show that the surface chemistry of the NaOH treated PDMS differs from O2 plasma treated PDMS. An important advantage of the NaOH treated surfaces is the enhanced stability, irrespective of whether the devices are stored in air or water.

Study on surface properties of PDMS microfluidic chips treated with albumin

Electrokinetic properties and morphology of PDMS microfluidic chips intended for bioassays are studied. The chips are fabricated by a casting method followed by polymerization bonding. Microchannels are coated with 1% solution of bovine serum albumin (BSA) in Tris buffer. Albumin passively adsorbs on the PDMS surface. Electrokinetic characteristics (electro-osmotic velocity, electro-osmotic mobility, and zeta potential) of the coated PDMS channels are experimentally determined as functions of the electric field strength and the characteristic electrolyte concentration. Atomic force microscopy (AFM) analysis of the surface reveals a "peak and ridge" structure of the protein layer and an imperfect substrate coating. On the basis of the AFM observation, several topologies of the BSA-PDMS surface are proposed. A nonslip mathematical model of the electro-osmotic flow is then numerically analyzed. It is found that the electrokinetic characteristics computed for a channel with the homogeneous distribution of a fixed electric charge do not fit the experimental data. Heterogeneous distribution of the fixed electric charge and the surface roughness is thus taken into account. When a flat PDMS surface with electric charge heterogeneities is considered, the numerical results are in very good agreement with our experimental data. An optimization analysis finally allowed the determination of the surface concentration of the electric charge and the degree of the PDMS surface coating. The obtained findings can be important for correct prediction and possibly for robust control of behavior of electrically driven PDMS microfluidic chips. The proposed method of the electro-osmotic flow analysis at surfaces with a heterogeneous distribution of the surface electric charge can also be exploited in the interpretation of experimental studies dealing with protein-solid phase interactions or substrate coatings.

An accessible micro-capillary electrophoresis device using surface-tension-driven flow

We present a rapidly fabricated micro-capillary electrophoresis chip that utilizes surface-tension-driven flow for sample injection and extraction of DNA. Surface-tension-driven flow (i.e. passive pumping) [G. M. Walker et al., Lab. Chip. 2002, 2, 131-134] injects a fixed volume of sample that can be predicted mathematically. Passive pumping eliminates the need for tubing, valves, syringe pumps, and other equipment typically needed for interfacing with microelectrophoresis chips. This method requires a standard micropipette to load samples before separation, and remove the resulting bands after analysis. The device was made using liquid phase photopolymerization to rapidly fabricate the chip without the need of special equipment typically associated with the construction of microelectrophoresis chips (e.g. cleanroom) [A. K. Agarwal et al., J. Micromech. Microeng. 2006, 16, 332-340; S. K. Mohanty et al., Electrophoresis 2006, 27, 3772-3778]. Batch fabrication time for the device presented here was 1.5 h including channel coating time to suppress electroosmotic flow. Devices were constructed out of poly-isobornyl acrylate and glass. A standard microscope with a UV source was used for sample detection. Separations were demonstrated using Promega BenchTop 100 bp ladder in hydroxyl ethyl cellulose (HEC) and oligonucleotides of 91 and 118 bp were used to characterize sample injection and extraction of DNA bands. The end result was an inexpensive micro-capillary electrophoresis device that uses tools (e.g. micropipette, electrophoretic power supplies, and microscopes) already present in most labs for sample manipulation and detection, making it more accessible for potential end users.

A microfluidic device for multiplexed protein detection in nano-liter volumes

We describe a microfluidic immunoassay device that permits sensitive and quantitative multiplexed protein measurements on nano-liter-scale samples. The device exploits the combined power of integrated microfluidics and optically encoded microspheres to create an array of approximately 100-microm(2) sensors functionalized with capture antibodies directed against distinct targets. This strategy overcomes the need for performing biochemical coupling of affinity reagents to the device substrate, permits multiple proteins to be detected in a nano-liter-scale sample, is scalable to large numbers of samples, and has the required sensitivity to measure the abundance of proteins derived from single mammalian cells. The sensitivity of the device is sufficient to detect 1000 copies of tumor necrosis factor (TNF) in a volume of 4.7nl.

Electrochemical generation of gradients in surfactant concentration across microfluidic channels

We report the generation and manipulation of spatial gradients in surfactant and micelle concentration across microfluidic channels by combining use of a redox-active surfactant with electrochemical methods. The approach is founded on the observation that 11-ferrocenylundecyltrimethylammonium bromide (FTMA) behaves as a surfactant in aqueous solution (e.g., self-assembles to form micelles at a critical concentration of 0.1 mM in aqueous 0.1 M Li(2)SO(4)) whereas oxidized FTMA remains dispersed in a monomeric state up to concentrations of at least 30 mM. By flowing aqueous FTMA solutions through microfluidic channels (width of 80 microm, depth of 72 microm, and length of 42 mm) and by applying potentials of 0 V (vs Ag|AgCl; cathode) and +0.3 V (vs Ag|AgCl; anode) to gold electrodes lining both side-walls of the microfluidic channels, we measured lateral gradients in concentration of oxidized FTMA and reduced FTMA to be generated across the microfluidic channels by splitting the exiting stream into four channels. These measurements revealed the lateral concentration profile of FTMA to be consistent with the presence of slowly diffusing micelles of FTMA in a spatially localized region near the cathode and monomeric FTMA only near the anode. The lateral concentration profiles of reduced and oxidized FTMA, and thus the patterning of micelles within the microfluidic channels, were manipulated via changes in the inlet FTMA concentration, potentials applied to the electrodes, and flow rate. These experimental measurements were compared to a simple model, which assumed fast electrode kinetics, lateral transport of FTMA by diffusion only (no migration), and local micelle-monomer equilibrium within the bulk solution. This comparison revealed qualitative but not quantitative agreement between model and experiment. Calculations of ionic conductivity and associated experimental measurements support the proposition that Ohmic resistance to the passage of current along the channel (between the working and the counter electrodes) contribute, in part, to the lack of quantitative agreement between the model and the measurements. The capability to generate and manipulate lateral concentration profiles of surfactants and micelles across microfluidic channels, as demonstrated by the results presented in this paper, offers the basis of new principles for continuous separation processes and microanalytical systems, and more broadly, new methods to generate gradients in concentration of analytes that interact with surfactants.

Separations in poly(dimethylsiloxane) microchips coated with supported bilayer membranes

Hybrid microchannels composed of poly(dimethylsiloxane) and glass were coated with supported bilayer membranes (SBMs) by the process of vesicle fusion. The electroosmotic mobility (mu(eo)) of zwitterionic, positively charged, and negatively charged phospholipid membranes was measured over a 4 h time to evaluate the stability of the coatings in an electric field. Coated microchips with a simple cross design were used to separate the fluorescent dyes fluorescein and Oregon Green. Migration time reproducibility was better than 5% RSD over 70 min of continuous separations. Separation of Oregon Green and fluorescein in channels coated with zwitterionic phosphatidylcholine (PC) membranes yielded efficiencies of 611,000 and 499,000 plates/m and a resolution of 2.4 within 2 s. Both zwitterionic and negatively charged membranes were used to separate peptide substrates from their phosphorylated analogues with efficiencies of 200,000-400,000 plates/m. Notably, separations of fluorescently labeled ABL substrate peptide from its phosphorylated counterpart were achieved using a high-salt physiological buffer with near-baseline resolution in 10 s. PC-coated devices were used to successfully separate enhanced green fluorescent protein (eGFP) from a fusion protein (eGFP-Crakl) with an efficiency of 358,000 and 278,000 plates/m respectively in less than 12 s. These SBM-based coatings may enable the separation of a broad range of analytes and may be ideal in biological applications for microfluidics.

Comparison of the analytical performance of electrophoresis microchannels fabricated in PDMS, glass, and polyester-toner

This paper compares the analytical performance of microchannels fabricated in PDMS, glass, and polyester-toner for electrophoretic separations. Glass and PDMS chips were fabricated using well-established photolithographic and replica-molding procedures, respectively. PDMS channels were sealed against three different types of materials: native PDMS, plasma-oxidized PDMS, and glass. Polyester-toner chips were micromachined by a direct-printing process using an office laser printer. All microchannels were fabricated with similar dimensions according to the limitations of the direct-printing process (width/depth 150 microm/12 microm). LIF was employed for detection to rule out any losses in separation efficiency due to the detector configuration. Two fluorescent dyes, coumarin and fluorescein, were used as model analytes. Devices were evaluated for the following parameters related to electrophoretic separations: EOF, heat dissipation, injection reproducibility, separation efficiency, and adsorption to channel wall.

Characterization and use of laser-based lysis for cell analysis on-chip

We demonstrate the use of a pulsed laser microbeam for cell lysis followed by electrophoretic separation of cellular analytes in a microfluidic device. The influence of pulse energy and laser focal point within the microchannel on the threshold for plasma formation was measured. The thickness of the poly(dimethylsiloxane) (PDMS) layer through which the beam travelled was a critical determinant of the threshold energy. An effective optical path length, Leff, for the laser beam can be used to predict the threshold for optical breakdown at different microchannel locations. A key benefit of laser-based cell lysis is the very limited zone (less than 5 microm) of lysis. A second asset is the rapid cell lysis times (approx. microseconds). These features enable two analytes, fluorescein and Oregon Green, from a cell to be electrophoretically separated in the channel in which cell lysis occurred. The resolution and efficiency of the separation of the cellular analytes are similar to those of standards demonstrating the feasibility of using a pulsed laser microbeam in single-cell analysis.

Dielectrophoretic manipulation of particles in a modified microfluidic H filter with multi-insulating blocks

The conventional microfluidic H filter is modified with multi-insulating blocks to achieve a flow-through manipulation and separation of microparticles. The device transports particles by exploiting electro-osmosis and electrophoresis, and manipulates particles by utilizing dielectrophoresis (DEP). Polydimethylsiloxane (PDMS) blocks fabricated in the main channel of the PDMS H filter induce a nonuniform electric field, which exerts a negative DEP force on the particles. The use of multi-insulating blocks not only enhances the DEP force generated, but it also increases the controllability of the motion of the particles, facilitating their manipulation and separation. Experiments were conducted to demonstrate the controlled flow direction of particles by adjusting the applied voltages and the separation of particles by size under two different input conditions, namely (i) a dc electric field mode and (ii) a combined ac and dc field mode. Numerical simulations elucidate the electrokinetic and hydrodynamic forces acting on a particle, with theoretically predicted particle trajectories in good agreement with those observed experimentally. In addition, the flow field was obtained experimentally with fluorescent tracer particles using the microparticle image velocimetry (mu-PIV) technique.

Zeta potential and electroosmotic mobility in microfluidic devices fabricated from hydrophobic polymers: 1. The origins of charge

This paper combines new experimental data for electrokinetic characterization of hydrophobic polymers with a detailed discussion of the putative origins of charge at water-hydrophobe interfaces. Complexities in determining the origin of charge are discussed in the context of design and modeling challenges for electrokinetic actuation in hydrophobic microfluidic devices with aqueous working fluids. Measurements of interfacial charge are complicated by slip and interfacial water structuring phenomena (see Part 2, this issue). Despite these complexities, it is shown that (i) several hydrophobic materials, such as Teflon and Zeonor, have predictable electrokinetic properties and (ii) electrokinetic data for hydrophobic microfluidic systems is most consistent with the postulate that hydroxyl ion adsorption is the origin of charge.

Temperature gradient focusing in a PDMS/glass hybrid microfluidic chip

This paper reports the application of temperature gradient focusing (TGF) in a PDMS/glass hybrid microfluidic chip. With TGF, by the combination of a temperature gradient along a microchannel, an applied electric field, and a buffer with a temperature-dependent ionic strength, analytes are focused by balancing their electrophoretic velocities against the bulk velocity of the buffer containing the analytes. In this work, Oregon Green 488 carboxylic acid was concentrated approximately 30 times as high as the initial concentration in 45 s at moderate electric strength of 70 V/cm and a temperature gradient of 55 degrees C across the PDMS/glass hybrid microfluidic chip with a 1 cm long capillary.

Surface modification of poly(dimethylsiloxane) with a perfluorinated alkoxysilane for selectivity toward fluorous tagged peptides

Poly(dimethylsiloxane) (PDMS) and similar polymers have proved to be of widespread interest for use in microfluidic and similar microanalytical devices. Surface modification of PDMS is required to extend the range of applications for devices made of this polymer, however. Here we report on the grafting of perfluorooctyltriethoxysilane via hydrolysis onto an oxidized PDMS substrate in order to form a fluorinated microchannel. Such a fluorinated device could be used for separating fluorous tagged proteins or peptides, similar to that which has been recently demonstrated in a capillary electrophoresis system or in an open tubular capillary column. The modified polymer is characterized using chemical force titrations, contact angle measurements, and X-ray photoelectron spectroscopy (XPS). We also report on a novel means of performing electroosmotic measurements on this material to determine the surface zeta potential. As might be expected, contact angle and chemical force titration measurements indicate the fluorinated surface to be highly hydrophobic. XPS indicates that fluorocarbon groups segregate to the surface of the polymer over a period of days following the initial surface modification, presumably driven by a lower surface free energy. One of the most interesting results is the zeta potential measurements, which show that significant surface charge can be maintained across a wide range of pH on this modified polymer, sufficient to promote electroosmotic flow in a microfluidic chip. Matrix-assisted time-of-flight mass spectrometry (MALDI-TOF MS) measurements show that a fluorous-tagged peptide will selectively adsorb on the fluorinated PDMS in aqueous solution, demonstrating that the fluorinated polymer could be used in devices designed for the enrichment or enhanced detection of fluorous-labeled proteins and peptides.

An impulsive, electropulsation-driven backflow in microchannels during electroporation

We describe for the first time an impulsive, electropulsation-driven backflow in microchannels for on-chip cell electroporation.

Phase-changing sacrificial layer fabrication of multilayer polymer microfluidic devices

We present a new approach for fabricating multilayer microfluidic devices in poly(methyl methacrylate). Paraffin wax was used as a phase-changing sacrificial layer to protect microstructures during solvent bonding. Microchannels in the top and bottom pieces were aligned with through-holes in the middle layer, resulting in microchannels that cross one another. No discernible delamination of the layers or leakage between channels was observed at pressures as high as 300 psi. The current versus voltage linearity in the crossover channel indicates that no Joule heating occurs at voltages of at least 2.0 kV. Moreover, a potential in the crossover channel did not affect the current in the separation channel. Rapid and efficient separation of fluorescently labeled amino acids was performed in these devices. Pressurized buffer flow or voltage applied in the crossover channel caused no leakage into or electrical interference with the separation channel. Our results demonstrate that sacrificial layers with solvent bonding can be implemented readily in the fabrication of robust and fluidically complex multilayer polymer microchips. These capabilities should facilitate the development of a new generation of sophisticated microfluidic systems.

Steady surface modification of polydimethylsiloxane microchannel and its application in simultaneous analysis of homocysteine and glutathione in human serum

A novel polydimethylsiloxane (PDMS) surface modification method for microchip electrophoresis has been developed to make a stable and sufficient electroosmotic flow (EOF). Poly(l-glutamic acid) (PGA) which had ionizable carboxyl groups at a high pH-range was immobilized on the surface of microchannel fabricated with PDMS. The surface modification involved surface oxidation by plasma, the silanization of 3-aminopropyldimethylethoxysilane (APDMES) and immobilization of PGA via amide bond. The modified channel was extremely stable against consecutive electric power supply over 5h, and its long-term stability was demonstrated by the efficient separation of four amino acid derivatives reproducibly after a week. Additionally, homocysteine (Hcy), important risk factor of cardiovascular disease, osteoporosis and problems in pregnancy, was successfully measured in human serum in modified PDMS channel with the other thio amino acid simultaneously.

Performance of SU-8 Microchips as Separation Devices and Comparison with Glass Microchips

Effective analytical performance of native, all-SU-8 separation microdevices is addressed by comparing their performance to commercial glass microdevices in microchip zone electrophoresis accompanied by fluorescence detection. Surface chemistry and optical properties of SU-8 microdevices are also examined. SU-8 was shown to exhibit repeatable electroosmotic properties in a wide variety of buffers, and SU-8 microchannels were successfully utilized in peptide and protein analyses without any modification of the native polymer surface. Selected, fluorescent labeled, biologically active peptides were baseline resolved with migration time repeatability of 2.3-3.6% and plate numbers of 112,900-179,800 m(-1). Addition of SDS (0.1%) or SU-8 developer (1.0%) to the separation buffer also enabled protein analysis by capillary zone electrophoresis. Plate heights of 2.4-5.9 microm were obtained for fluorescent labeled bovine serum albumin. In addition, detection sensitivity through SU-8 microchannels was similar to that through BoroFloat glass, when fluorescence illumination was provided at visible wavelengths higher than 500 nm. On the whole, the analytical performance of SU-8 microchips was very good and fairly comparable to that of commercial glass chips as well as that of traditional capillary electrophoresis and chromatographic methods. Moreover, lithography-based patterning of SU-8 enables straightforward integration of multiple functions on a single chip and favors fully microfabricated lab-on-a-chip systems.

Microchips and single-photon avalanche diodes for DNA separation with high sensitivity

Modern techniques for DNA and protein analysis and separation rely on measurements of LIF and face a trend toward employing progressively smaller samples. The currently employed detectors that provide the required ultrahigh sensitivity, e.g. photomultiplier tubes (PMTs), are bulky and/or costly and delicate, whereas a key issue for the development of compact and economical instruments is the availability of miniaturized, inexpensive, and ultrasensitive photodetectors. The planar epitaxial silicon single-photon avalanche diodes (SPADs) combine the typical advantages of microelectronics (miniaturization, ruggedness, low voltage, low power, low cost, etc.) with high sensitivity, even better than that of PMTs. The suitability of such SPADs to microchip CE has been here ascertained by developing a new apparatus with dual-wavelength LIF detection. The apparatus has been experimented in studies on the EOF suppression and on the coating stability and tested in rapid sizing of DNA fragments. The experimental results obtained in the separation of Cy5-labeled oligonucleotide demonstrate sensitivity better than 3 pM, which corresponds to less than 100 fluorescent molecules in the 50 pL illuminated volume.

The intrinsic charge on hydrophobic microfluidic substrates

A synthesis of the literature provides an explanation for the hitherto unexplained charge on hydrophobic microfluidic substrates. It is due to the adsorption of hydroxide ions created by the enhanced autolysis of water at these surfaces.

Miniaturized fluorescence detection chip for capillary electrophoresis immunoassay of agricultural herbicide atrazine

This paper reports a miniaturized fluorescence detection chip for capillary electrophoresis immunoassay of atrazine, which effectively reduces the size of fluorescence detection system. The photodiode with fluorescence filter was embedded in PDMS (polydimethylsiloxane) microfluidic chip and was placed just below the microfluidic channel. This detection chip is only few mm thick without loss of fluorescence due to the proximity of photodiode and channel. To investigate the feasibility of in situ detection of agricultural herbicide, atrazine was detected using capillary electrophoresis immunoassay in microfluidic chip. Mixture of 570 nM fluorescence-labeled atrazine (Ag*) and 700 nM anti-atrazine antibody (Ab) was injected and separated in 25 mm long microfluidic channel. The separated peaks of Ab-Ag* immunocomplex and Ag* were detected by the miniaturized detector and the change of peak magnitude was also observed with the variation of Ab concentration. The result was verified with those of external PMT (photomultiplier tube) and commercial capillary electrophoresis system. Hence, we have demonstrated the feasibility of portable CE immunoassay of atrazine with on-chip fluorescence detector.

Zeta-potential measurement using the Smoluchowski equation and the slope of the current-time relationship in electroosmotic flow

The zeta -potential of a solid-liquid interface is an important surface characterization quantity for applications ranging from the development of biomedical polymers to the design of microfluidic devices. This study presents a novel experimental technique to measure the zeta -potentials of flat surfaces. This method combines the Smoluchowski equation with the measured slope of current-time relationship in electroosmotic flow. This method is simple and accurate in comparison with the traditional streaming potential and electrophoresis techniques. Using this method the zeta -potentials of glass and poly(dimethylsiloxane) (PDMS) coated surfaces in KCl and LaCl3 aqueous solutions were measured using several flow channels ranging from 200 to 300 microm in height. The zeta -potential was found to vary from -88 to -66 mV for glass surface and -110 to -68 mV for PDMS surfaces depending on the electrolyte and the ionic concentration. The measured values of the zeta -potential are found to be independent of the channel size and the applied driving voltage and generally are repeatable within +/-6%.

Thin double layer approximation to describe streaming current fields in complex geometries: analytical framework and applications to microfluidics

We set up an analytical framework that allows one to describe and compute streaming effects and electro-osmosis on an equal footing. This framework relies on the thin double layer approximation commonly used for description of electroosmotic flows, but rarely used for streaming problems. Using this framework we quantitatively assess the induction of bulk streaming current patterns by topographic or charge heterogeneities on surfaces. This too also permits analytical computation of all linear electrokinetic effects in complex microfluidic geometries, and we discuss a few immediate applications.

Sulfonated-polydimethylsiloxane (PDMS) microdevices with enhanced electroosmotic pumping and stability

Polydimethylsiloxane (PDMS) microfluidic devices offer several advantages in terms of cost and ease of fabrication compared with those fabricated from both glass and silicon materials. PDMS, however, has some potential disadvantages compared with other materials including high hydrophobicity, which makes filling the micron-sized channels difficult, and minimal surface charge resulting in reduced electroosmotic flow (EOF). Here, we describe the oxidation of the PDMS surface to form silanol groups using both air plasma and a discharge from a Tesla coil, and subsequent modification to form sulfonated-PDMS surfaces. The flow performance of freshly prepared and aged sulfonated-PDMS chips was determined at pH 5 and compared with those of unmodified and oxidized PDMS chips. The electroosmotic mobility (µeo) for a sulfonated-PDMS microdevice was determined at various pH values (pH 3~8) and compared with that for an oxidized PDMS chip. The lower pKa of a sulfonic acid modified surface compared with a silanol modified surface generated a stronger EOF over the entire pH range studied. Chemical force titrations were used to characterize the changes in functional groups present on the surface of freshly prepared and aged sulfonated-PDMS surfaces. These experiments show that the sulfonated-PDMS is a superior material for use in microfluidic applications because (i) it supports EOF over a much wider range of pH than similar polymer materials and (ii) is less susceptible to degradation of its EOF rate owing to air aging effects and surface reorganization.Key words: polydimethylsiloxane (PDMS), sulfonated surface modification, electroosmotic flow (EOF), aging effect, chemical force titrations.

Electrokinetic-driven microfluidic system in poly(dimethylsiloxane) for mass spectrometry detection integrating sample injection, capillary electrophoresis, and electrospray emitter on-chip

A novel microsystem device in poly(dimethylsiloxane) (PDMS) for MS detection is presented. The microchip integrates sample injection, capillary electrophoretic separation, and electrospray emitter in a single substrate, and all modules are fabricated in the PDMS bulk material. The injection and separation flow is driven electrokinetically and the total amount of external equipment needed consists of a three-channel high-voltage power supply. The instant switching between sample injection and separation is performed through a series of low-cost relays, limiting the separation field strength to a maximum of 270 V/cm. We show that this set-up is sufficient to accomplish electrospray MS analysis and, to a moderate extent, microchip separation of standard peptides. A new method of instant in-channel oxidation makes it possible to overcome the problem of irreversibly bonded PDMS channels that have recovered their hydrophobic properties over time. The fast method turns the channel surfaces hydrophilic and less prone to nonspecific analyte adsorption, yielding better separation efficiencies and higher apparent peptide mobilities.

Electroosmotic flow in poly(dimethylsiloxane) microchannels

This paper reports on the study of electroosmotic flow (EOF) in poly(dimethylsiloxane) (PDMS) microchannels on the basis of indirect amperometric detection method. Gradual increase of EOF rate in freshly prepared PDMS microchannels was observed with the running buffer of phosphate buffer solution (PBS). With the same concentration (10 mM) of PBS containing different cations and the same pH value (7.0) and, the time of the stable EOF in PDMS microchannels under the applied separation voltage of 1000 V was 49.8 s (Li+ -PBS), 57.1 s (Na+ -PBS), 91 s (K+ -PBS), respectively. Meanwhile, the different adsorption of cations (Li+, Na+ and K+) on hydrophobic PDMS wall was observed through their separation in PDMS microchannels. Such experimental results demonstrated that the EOF in PDMS microchannels came from the cations and anions adsorbed on PDMS wall. This study would not only help us understand the surface state of PDMS, but also provide a useful guidance for establishing the effective surface modification methods in PDMS microchip CE.

Functionality and stability of heparin immobilized onto poly(dimethylsiloxane)

Poly(dimethylsiloxane) (PDMS) has become an attractive material when working in the field of microfluidics, mainly because of the rapid prototyping process it involves. The increased surface volume ratio in microchannels makes the interaction between sample and material surface highly important, evident when handling complex biological samples such as plasma or blood. This study demonstrates a new grade of non-covalent heparin surface that adds efficient anticoagulant property to the PDMS material. The surface modification is a simple and fast one-step process performed at neutral pH, optimal when working with closed microsystems. The heparin formed a uniform and functional coating on hydrophobic PDMS with comparatively high level of antithrombin-binding capacity. In addition, long-term studies revealed that the immobilized heparin was more or less stable in the microchannels over a time of three weeks. Recalcified plasma in contact with native PDMS showed complete coagulation after 1h, while no fibrin formation was detected in plasma incubated on heparin-coated PDMS within the same time. In conclusion, we see the heparin coating developed and evaluated in this study as a tool that greatly facilitates the use of PDMS in microfluidics dealing with plasma or blood samples.

Profiling pH Gradients Across Nanocapillary Array Membranes Connecting Microfluidic Channels

Nanocapillary array membranes (NCAMs), comprised of thin (d approximately 5-10 microm) nuclear track-etched polycarbonate sheets containing approximately 10(8) cm(-2) nearly parallel nanometer-diameter capillaries, may act to gate fluid transport between microfluidic channels to effect, for example, sample collection. There is interest in H+-transport across these NCAMs because there is significant practical interest in being able to process analyte-containing samples under different pH conditions in adjacent layers of an integrated microfluidic circuit and because protons, with their inherently high mobility, present a challenge in separating microfluidic environments with different properties. To evaluate the capability of NCAMs to support pH gradients, the proton transport properties of NCAMs were studied using laser scanning confocal fluorescence microscopy (LSCFM). Spatiotemporal maps of [H+] in microfluidic channels adjacent to the NCAMs yield information regarding diffusive and electrokinetic transport of protons. The NCAMs studied here are characterized by a positive zeta potential, zeta > 0, so at small nanocapillary diameters, the overlap of electrical double layers associated with opposite walls of the nanocapillary establish an energy barrier for either diffusion or electrokinetic transport of cations through the nanometer-diameter capillaries due to the positive charge on the nanocapillary surface. Proton transfer through an NCAM into microchannels is reduced for pore diameters, d < or = 50 nm and ionic strengths I < or = 50 mM, while for large pore diameters or solution ionic strengths, the incomplete overlap of electric double layer allows more facile ionic transfer across the membranes. These results establish the operating conditions for the development of multilevel integrated nanofluidic/microfluidic architectures which can support multidimensional chemical analysis of mass-limited samples requiring sequential operations to be implemented at different pH values.

Isoelectric focusing in cyclic olefin copolymer microfluidic channels coated by polyacrylamide using a UV photografting method

As an alternative material to glass or silicon, microfluidic devices made from a cyclic olefin copolymer (COC) were fabricated. This material is of interest because of the relative ease of fabrication, low costs, and solvent resistance. However, as a result of the strong hydrophobic interactions normally present, COC surfaces are not suitable for protein separations. To reduce the protein adsorption and make COC suitable for protein separations, UV-initiated grafting of polyacrylamide was used to coat the surface of COC devices. The change in surface properties caused by different graft times was studied. The surface hydrophilicity and electroosmotic mobility were characterized by contact angle and electroosmosis measurements. Isoelectric focusing was performed to test protein separations in polyacrylamide-coated COC microchannels. A single protein, carbonic anhydrase, was used to analyze the focusing effects and peak capacities in uncoated and polyacrylamide-coated COC devices. Peak capacities ranging from 75 to 190 were achieved with a polyacrylamide-coated surface. A mixture of two proteins, conalbumin labeled with Alexa Fluor 488 and beta-lactoglobulin A labeled with Alexa Fluor 546, was used to test protein separations. Linear and rapid separation of proteins was achieved in the polyacrylamide-coated COC microfluidic device.

Characterization of SU-8 for electrokinetic microfluidic applications

The characterization of SU-8 microchannels for electrokinetic microfluidic applications is reported. The electroosmotic (EO) mobility in SU-8 microchannels was determined with respect to pH and ionic strength by the current monitoring method. Extensive electroosmotic flow (EOF), equal to that for glass microchannels, was observed at pH > or =4. The highest EO mobility was detected at pH > or =7 and was of the order of 5.8 x 10(-4) cm(2) V(-1) s(-1) in 10 mM phosphate buffer. At pH < or =3 the electroosmotic flow was shown to reverse towards the anode and to reach a magnitude of 1.8 x 10(-4) cm(2) V(-1) s(-1) in 10 mM phosphate buffer (pH 2). Also the zeta-potential on the SU-8 surface was determined, employing lithographically defined SU-8 microparticles for which a similar pH dependence was observed. SU-8 microchannels were shown to perform repeateably from day to day and no aging effects were observed in long-term use.

Poly(dimethylsiloxane) thin films as biocompatible coatings for microfluidic devices: cell culture and flow studies with glial cells

Oxygen plasma treatment of poly(dimethylsiloxane) (PDMS) thin films produced a hydrophilic surface that was biocompatible and resistant to biofouling in microfluidic studies. Thin film coatings of PDMS were previously developed to provide protection for semiconductor-based microoptical devices from rapid degradation by biofluids. However, the hydrophobic surface of native PDMS induced rapid clogging of microfluidic channels with glial cells. To evaluate the various issues of surface hydrophobicity and chemistry on material biocompatibility, we tested both native and oxidized PDMS (ox-PDMS) coatings as well as bare silicon and hydrophobic alkane and hydrophilic oligoethylene glycol silane monolayer coated under both cell culture and microfluidic studies. For the culture studies, the observed trend was that the hydrophilic surfaces supported cell adhesion and growth, whereas the hydrophobic ones were inhibitive. However, for the fluidic studies, a glass-silicon microfluidic device coated with the hydrophilic ox-PDMS had an unperturbed flow rate over 14 min of operation, whereas the uncoated device suffered a loss in rate of 12%, and the native PDMS coating showed a loss of nearly 40%. Possible protein modification of the surfaces from the culture medium also were examined with adsorbed films of albumin, collagen, and fibrinogen to evaluate their effect on cell adhesion.

Chemical force titrations of amine- and sulfonic acid-modified poly(dimethylsiloxane)

Chemical force titrations-measurements of the adhesive interaction between a pair of suitably chemically modified atomic force microscopy (AFM) tip and sample surfaces as a function of pH-have been carried out for various combinations of silanol, amine, carboxylic acid, and sulfonic acid functional groups on both tip and sample. The primary surface material studied was poly(dimethylsiloxane) (PDMS). Surface modification was carried out using a plasma oxidation process to form silanol sites; further modification with amine or sulfonic acid sites was carried out by reaction of the silanol sites with the appropriate trialkoxysilane derivative. AFM tips were also modified using trialkoxysilane compounds. In the cases of tip/sample combinations with the same functional group on each, surface pK(1/2) values could be determined. In several "mixed" tip/sample combinations, a peak appeared in the titration curve midway between the surface pK(1/2) values of the tip and sample, consistent with an ionic H-bonding model for the interactions. The amine/sulfonic acid pair showed more complex behavior; the amine-terminated tip/sulfonic acid-terminated PDMS surface force titration curve consisted of two peaks centered at pH 4 and pH 8. Reversing the tip/sample pair resulted in the peak positions being shifted upward by 1.0 pH unit. The peak appearing at lower pH is assigned to electrostatic interactions between the two oppositely charged surfaces, whereas the higher pH peak is believed to arise due to ionic H-bonding interactions. AFM images show the effects on surface patterning of amine- and sulfonic acid-modified PDMS surfaces that have undergone two different oxidation methods (air plasma oxidation and Tesla coil oxidation). The surface morphologies of freshly prepared and 24 h aged air plasma oxidized PDMS are also discussed in this study.

Parametric investigation on the effect of channel topologies on electrophoretic separations

This paper presents a systematic study that illustrates the importance of the topologies of microchannels on electrokinetically based separation. Using theoretical and numerical analyses, we designed and showed that topologies that significantly increased the surface-to-volume ratio of the channel can provide dramatic improvement in the ability of the channel both to dissipate the heat generated by Joule heating and to reduce the axial dispersion associated with the siphoning effect. The incremental benefit and tradeoff of geometric complexity was also evaluated. The improvement offered by topographically patterned channels, such as finned structures, is especially pertinent in the development of preparative or semi-preparative scale electrokinetically driven separations, such as capillary electrophoresis and capillary electrochromatography, in which large cross sections of channels are required to achieve the needed volumetric throughput.

Low-dispersion electrokinetic flows for expanded separation channels in microfluidic systems:

A novel methodology to design on-chip conduction channels is presented for expansion of low-dispersion separation channels. Designs are examined using two-dimensional numerical solutions of the Laplace equation with a Monte Carlo technique to model diffusion. The design technique relies on trigonometric relations that apply for ideal electrokinetic flows. Flows are rotated and stretched along the abrupt interface between adjacent regions having differing specific permeability. Multiple interfaces can be placed in series along a channel. The resulting channels can be expanded to extreme widths while minimizing dispersion of injected analyte bands. These channels can provide a long path length for line-of-sight optical absorption measurements. Expanded sections can be reduced to enable point detection at the exit section of the channel. Designed to be shallow, these channels have extreme aspect ratios in the wide section, greatly increasing the surface-to-volume ratio to increase heat removal and decrease unwanted pressure-driven flow. The use of multiple interfaces is demonstrated by considering several three-interface designs. Faceted flow splitters can be constructed to divide channels into any number of exit channels while minimizing dispersion. The resulting manifolds can be used to construct medians for structural support in wide, shallow channels.