Interfacial control of lid opening in Thermomyces lanuginosa lipase

Novel and highly regioselective route for synthesis of 5-fluorouridine lipophilic ester derivatives by lipozyme TL IM

For the first time, lipozyme TL IM, an inexpensive lipase from Thermomyces lanuginosa, was successfully applied to the regioselective synthesis of lipophilic 5-fluorouridine ester derivatives. The ESI-MS and (13)C NMR analysis confirmed that the end products of the acylation were 5'-O-acyl 5-fluorouridines, more powerful anti-tumor drugs than 5-fluorouridine itself. Notably, the chain length of acyl donors had an obvious effect on the initial rate and the maximum substrate conversion of the regioselective acylation. The acylation of 5-fluorouridine with vinyl laurate was used as a model to explore the influence of various factors on the reaction with respect to the initial rate, the maximum substrate conversion and the regioselectivity. The optimum water activity, the molar ratio of vinyl laurate to 5-fluorouridine, reaction temperature and shaking rate were 0.07, 15/1, 45 degrees C and 200rpm, respectively, under which the maximum substrate conversion and the regioselectivity were as high as 98.4 and >99%, respectively, after a reaction time of around 6h.

Spectroscopic and catalytic studies of lipases in ternary hexane-1-propanol-water surfactantless microemulsion systems

A series of water-in-oil microemulsion systems formulated without surfactant were used to solubilize lipases from Rhizomucor miehei and Candida antarctica B. The effect of the system's composition on the velocity of enzymic reactions was investigated following a model esterification reaction. The interaction between enzymes and the microemulsion environment was studied by steady state fluorescence spectroscopy. The site of localization of the enzyme within the different microdomains of the dispersed phase was investigated by applying the fluorescence energy transfer technique. To determine the properties of the interface between water and organic solvent of the surfactantless microemulsion systems the Electron Paramagnetic Resonance (EPR) spectroscopic technique was applied. The results indicated that even at low water content, water-rich structures are formed. This was confirmed by conductivity measurements. By the addition of enzyme it was observed that when the aqueous phase of the surfactantless microemulsion systems exceeds 2% (v/v) the enzyme retains its catalytic activity, as it is located within the water pools that protect it from the organic solvent. These confined water phases show a propanol rich interface with hexane and their structure depends on the system's composition.

Creation of Rhizopus oryzae lipase having a unique oxyanion hole by combinatorial mutagenesis in the lid domain

Combinatorial libraries of the lid domain of Rhizopus oryzae lipase (ROL; Phe88Xaa, Ala91Xaa, Ile92Xaa) were displayed on the yeast cell surface using yeast cell-surface engineering. Among the 40,000 transformants in which ROL mutants were displayed on the yeast cell surface, ten clones showed clear halos on soybean oil-containing plates. Among these, some clones exhibited high activities toward fatty acid esters of fluorescein and contained non-polar amino acid residues in the mutated positions. Computer modeling of the mutants revealed that hydrophobic interactions between the substrates and amino acid residues in the open form of the lid might be critical for ROL activity. Based on these results, Thr93 and Asp94 were further combinatorially mutated. Among 6,000 transformants, the Thr93Thr, Asp94Ser and Thr93Ser, Asp94Ser transformants exhibited a significant shift in substrate specificity toward a short-chain substrate. Computer modeling of these mutants suggested that a unique oxyanion hole, which is composed of Thr85 Ogamma and Ser94 Ogamma, was formed and thus the substrate specificity was changed. Therefore, coupling combinatorial mutagenesis with the cell surface display of ROL could lead to the production of a unique ROL mutant.

A small-angle neutron scattering study of biologically relevant mixed surfactant micelles comprising 1,2-diheptanoyl-sn-phosphatidylcholine and sodium dodecyl sulfate or dodecyltrimethylammonium bromide

Small-angle neutron scattering (SANS) has been employed to characterize mixed micelles comprising the surfactants 1,2-diheptanoyl--phosphatidylcholine (DHPC)/sodium dodecyl sulfate (SDS) and 1,2-diheptanoyl--phosphatidylcholine (DHPC)/dodecyltrimethylammonium bromide (DTAB) using the classical model of a micelle consisting of a hydrocarbon core surrounded by a polar shell. Various constraints are applied to the data fitting, specifically the volume of the hydrocarbon core using the aggregation number determined from time-resolved fluorescence quenching (TRFQ) and the degree of micelle hydration as determined from an electron paramagnetic resonance (EPR) experiment. The morphologies of the DHPC/SDS and DHPC/DTAB mixed micelles are largely invariant with composition-as might be expected given the similarity in the tail volumes of the respective surfactants, and the observed behaviour of the aggregation number-with a radius comparable to the fully extended length of a dodecyl chain, the longer of the two hydrophobic moieties. The shell thickness is also largely invariant with composition, indicating that the phosphatidylcholine headgroup lies flat at the interface. For both cases, the degree of counter-ion dissociation extracted from the fitting of the SANS data increases significantly on addition of DHPC, in a manner very similar to that observed for related binary surfactant mixtures, provided there is only a small change in micelle aggregation number (micelle curvature). The coincidence of the degrees of counter-ion dissociation for these quite different systems suggests a common underlying behaviour in which the nonionic species merely dilutes the surface charge associated with the ionic headgroups.

Phospholipid containing mixed micelles

Mixed micelles of l,2-diheptanoyl-sn-grycero-3-phosphocholine (DHPC) with ionic detergents were prepared to develop well characterized substrates for the study of lipolytic enzymes. The aggregates that formed on mixing DHPC with the anionic surfactant sodium dodecyl sulfate (SDS) and with the positively charged dodecyl trimethylammonium bromide (DTAB) were investigated using time-resolved fluorescence quenching (TRFQ) to determine the aggregation numbers and bimolecular collision rates, and electron spin resonance (ESR) to measure the hydration index and microviscosity of the micelles at the micelle-water interface. Mixed micelles between the phospholipid and each of the detergents formed in all compositions, yielding interfaces with varying charge, hydration, and microviscosity. Both series of micelles were found to be globular up to 0.7 mole fraction of DHPC, while the aggregation numbers varied within the same concentration range of the components less than 15%. Addition of the zwitterionic phospholipid component increased the degree of counterion dissociation as measured by the quenching of the fluorescence of pyrene by the bromide ions bound to DHPC/DTAB micelles, showing that at 0.6 mole fraction of DHPC 80% of the bromide ions are dissociated from the micelles. The interface water concentration decreased significantly on addition of DHPC to each detergent. For combined phospholipid and detergent concentration of 50 mM the interface water concentration decreased, as measured by ESR of the spin-probes, from 38.5 M/L of interface volume in SDS alone to 9 M/L when the phospholipid was present at 0.7 mole fraction. Similar addition of DHPC to DTAB decreased the interfacial water concentration from 27 M/L to 11 M/L. Determination of the physicochemical parameters of the phospholipid containing mixed micelles here presented are likely to provide important insight into the design of assay systems for kinetic studies of phospholipid metabolizing enzymes.

Discrimination between closed and open forms of lipases using electrophoretic techniques

The enhanced catalytic activity of lipases is often associated with structural changes. The three-dimensional (3D) structures showed that the covalently inhibited lipases exist under their open conformations, in contrast to their native closed forms. We studied the inhibition of various lipases--human and dog gastric lipases, human pancreatic lipase, and Humicola lanuginosa lipase--by the octyl-undecyl phosphonate inhibitor, and we measured the subsequent modifications of their respective electrophoretic mobility. Furthermore, the experimental values of the isoelectric points found for the native (closed) and inhibited (open) lipases are in agreement with theoretical calculations based on the electrostatic potential. We concluded that there is a significant difference in the isoelectric points between the closed (native) and open (inhibited) conformations of the four lipases investigated. Thus, analysis of the electrophoretic pattern is proposed as an easy experimental tool to differentiate between a closed and an open form of a given lipase.

Low microwave-amplitude ESR spectroscopy: measuring spin-relaxation interactions of moderately immobilized spin labels in proteins

Electron spin resonance (ESR) spectroscopy in combination with site-directed spin labeling (SDSL) is a powerful tool for determining protein structure, dynamics and interactions. We report here a method for determining interactions between spin labels and paramagnetic relaxation agents, which is performed under subsaturating conditions. The low microwave-field amplitude employed (h(1)<0.36 G) only requires standard, commercially available ESR equipment. The effect of relaxation enhancement on the spin-spin-relaxation time, T(2e), is measured by this method, and compared to classical progressive power saturation performed on a free spin label, (1-oxyl-2,2,5,5-tetramethyl-Delta(3)-pyrroline-3-methyl)methanethiosulfonate (MTSL), and a spin-labeled protein (Thermomyces lanuginosa lipase, TLL-I252C), employing the water-soluble relaxation agent chromium(III) oxalate (Crox) in concentrations between 0-10 mM. The low-amplitude theory showed excellent agreement with that of classical power saturation in quantifying Crox-induced relaxation enhancement. Low-amplitude measurements were then performed using a standard resonator, with Crox, on 11 spin-labeled TLL mutants displaying rotational correlation times in the motional narrowing regime. All spin-labeled proteins exhibited significant changes in T(2e). We postulate that this novel method is especially suitable for studying moderately immobilized spin labels, such as those positioned at exposed sites in a protein. This method should prove useful for research groups with access to any ESR instrumentation.

Humicola lanuginosa lipase hydrolysis of mono-oleoyl-rac-glycerol at the lipid-water interface observed by atomic force microscopy

A new type of planar lipid substrate for Humicola lanuginosa lipase (HLL) has been prepared by depositing a monolayer of 1-mono-oleoyl-rac-glycerol (MOG) on top of a monolayer of dipalmitoyl-phosphatidylcholine (DPPC) on mica by the Langmuir-Blodgett (LB) technique. The bilayer was subsequently exposed to HLL in a liquid cell of an atomic force microscope (AFM) allowing the time course of the lipolytic degradation to be observed. By analysing a series of AFM images, we find that enzymes are preferentially activated at the edge of nano-scale defects present in the bilayer prior to enzyme injection, while defect-free areas of the substrate are surprisingly stable towards enzyme degradation. The initial rate of hydrolysis is found to be proportional to the perimeter length, P, of the initial nano-scale defects as well as the bulk enzyme concentration, c(HLL); d(lipid)/dt=k P c(HLL). We estimate the specific rate of MOG hydrolysis by HLL to be 2.5x10(4) MOG molecules/(minute x molecule of HLL).

Long-chain fatty acyl-CoA esters induce lipase activation in the absence of a water-lipid interface

In most lipases a mobile element or lid domain covers the catalytic site of the enzyme and the lid opening event, which usually proceed at a lipid-water interface, is required to form the catalytically competent lipase. We report here a noticeable increase in activity of two fungal lipases assayed in aqueous solution in absence of any interface when adding submicellar concentrations of amphipathic physiological molecules like long-chain acyl-CoAs. The catalytic activity was dramatically dependent on the acyl chain length of the amphiphile and could be related with a lid-opening process. Our data support that lipase activation can be triggered in the absence of a well-defined interface, and stresses the notion that other non-aggregated amphipathic constituents of the local microenvironment can act as putative regulators of lipase activity.

Effect of charge reversal mutations on the ligand- and membrane-binding properties of liver fatty acid-binding protein

Liver fatty acid-binding protein (FABP) is able to bind to anionic phospholipid vesicles under conditions of low ionic strength. This binding results in the release of ligand, the fluorescent fatty acid analogue 11-dansylaminoundecanoic acid (DAUDA), with loss of fluorescence intensity (Davies, J. K., Thumser, A. E. A., and Wilton, D. C. (1999) Biochemistry 38, 16932-16940). Using a strategy of charge reversal mutagenesis, the potential role of specific cationic residues in promoting interfacial binding of FABP to anionic phospholipid vesicles has been investigated. Cationic residues chosen included those within the alpha-helical region (Lys-20, Lys-31, and Lys-33) and those that make a significant contribution to the positive surface potential of the protein (Lys-31, Lys-36, Lys-47, Lys-57, and Arg-126). Only three cationic residues make a significant contribution to interfacial binding, and these residues (Lys-31, Lys-36, and Lys-57) are all located within the ligand portal region, where the protein may be predicted to exhibit maximum disorder. The binding of tryptophan mutants, F3W, F18W, and C69W, to dioleoylphosphatidylglycerol vesicles, containing 5 mol% of the fluorescent phospholipid dansyldihexadecanoylphosphatidylethanolamine, was monitored by fluorescence resonance energy transfer (FRET). All three mutants showed enhanced dansyl fluorescence due to FRET on addition of phospholipid to protein; however, this fluorescence was considerably greater with the F3W mutant, consistent with the N-terminal region of the protein coming in close proximity to the phospholipid interface. These results were confirmed by succinimide quenching studies. Overall, the results indicate that the portal region of liver FABP and specifically Lys-31, Lys-36, and Lys-57 are involved in the interaction with the interface of anionic vesicles and that the N-terminal region of the protein undergoes a conformational change, resulting in DAUDA release.

Surface fluorescence resonance energy transfer studies on interfacial adsorption of Thermomyces (humicola) lanuginosa lipase, using monomolecular films of cis-parinaric acid

The fluorescence resonance energy transfer (FRET) technique was adapted to study the process whereby lipase is adsorbed to monomolecular lipid films spread at the air-water interface. When cis-parinaric acid (cis-PnA) was spread over an aqueous subphase before the injection of sodium taurodeoxycholate (NaTDC) and Thermomyces lanuginosa lipase (TLL), no FRET was observed. Under these conditions, no adsorption of TLL was detected using an ELISA. In contrast, FRET occurred when cis-PnA was spread over an aqueous subphase containing NaTDC and TLL. The FRET signals observed were attributed to the interactions between the adsorbed TLL and the cis-PnA monomolecular films. Comparisons between the fluorescence emission spectra corresponding to the bulk phase and the aspirated film, in the presence and absence of TLL, showed that cis-PnA was undetectable in the bulk phase. We concluded that the FRET originated from the interface and not from the bulk phase. Using surface FRET, we estimated that the surface excess of the catalytically inactive mutant, TLL(S146A), was 1.6 higher than that present in the wild-type TLL. This finding is in agreement with independent measurements of the surface excess of TLL and TLL(S146A) on monomolecular films of cis-PnA.

Orientation and conformation of a lipase at an interface studied by molecular dynamics simulations

Electron density profiles calculated from molecular dynamics trajectories are used to deduce the orientation and conformation of Thermomyces lanuginosa lipase and a mutant adsorbed at an air-water interface. It is demonstrated that the profiles display distinct fine structures, which uniquely characterize enzyme orientation and conformation. The density profiles are, on the nanosecond timescale, determined by the average enzyme conformation. We outline a computational scheme that from a single molecular dynamics trajectory allows for extraction of electron density profiles referring to different orientations of the lipase relative to an implicit interface. Profiles calculated for the inactive and active conformations of the lipase are compared with experimental electron density profiles measured by x-ray reflectivity for the lipase adsorbed at an air-water interface. The experimental profiles contain less fine structural information than the calculated profiles because the resolution of the experiment is limited by the intrinsic surface roughness of water. Least squares fits of the calculated profiles to the experimental profiles provide areas per adsorbed enzyme and suggest that Thermomyces lanuginosa lipase adsorbs to the air-water interface in a semiopen conformation with the lid oriented away from the interface.

Selective reduction and chemical modification of oxidized lipase cysteine mutants

Thirteen single-cysteine mutants of the 33 kDa fungal triacylglycerol lipase Thermomyces (formerly Humicola) lanuginosa lipase (TLL, EC 3.1.1.3) were produced and characterized for the purpose of site-directed chemical modification with spectroscopic reporter groups. All cysteine mutants were found to be predominantly blocked by oxidation to disulfides with endogenous cysteine during production. The fraction of lipase molecules with free sulfhydryl groups was analyzed by labeling with N-biotinylaminoethyl methanethiosulfonate, followed by a novel dot-blot method based on biotin-streptavidin interactions. A non-invasive method for the reduction of the introduced cysteine was elaborated for this protein containing three native disulfide bridges. The site-specifically reduced TLL mutants were then labeled with the sulfhydryl-specific reagents 2-(5-dimethylaminonaphth-1-ylsulfonamido)ethyl methanethiosulfonate or (1-oxyl-2,2,5,5-tetramethyl-Δ3-pyrroline-3-methyl) methanethiosulfonate, and studied by fluorescence and electron spin resonance (ESR) spectroscopy.Key words: lipase, cysteine mutant, selective reduction, chemical modification, methanethiosulfonate.

Binding of Thermomyces (Humicola) lanuginosa lipase to the mixed micelles of cis-parinaric acid/NaTDC

The binding of Thermomyces lanuginosa lipase and its mutants [TLL(S146A), TLL(W89L), TLL(W117F, W221H, W260H)] to the mixed micelles of cis-parinaric acid/sodium taurodeoxycholate at pH 5.0 led to the quenching of the intrinsic tryptophan fluorescence emission (300-380 nm) and to a simultaneous increase in the cis-parinaric acid fluorescence emission (380-500 nm). These findings were used to characterize the Thermomyces lanuginosa lipase/cis-parinaric acid interactions occurring in the presence of sodium taurodeoxycholate. The fluorescence resonance energy transfer and Stern-Volmer quenching constant values obtained were correlated with the accessibility of the tryptophan residues to the cis-parinaric acid and with the lid opening ability of Thermomyces lanuginosa lipase (and its mutants). TLL(S146A) was found to have the highest fluorescence resonance energy transfer. In addition, a TLL(S146A)/oleic acid complex was crystallised and its three-dimensional structure was solved. Surprisingly, two possible binding modes (sn-1 and antisn1) were found to exist between oleic acid and the catalytic cleft of the open conformation of TLL(S146A). Both binding modes involved an interaction with tryptophan 89 of the lipase lid, in agreement with fluorescence resonance energy transfer experiments. As a consequence, we concluded that TLL(S146A) mutant is not an appropriate substitute for the wild-type Thermomyces lanuginosa lipase for mimicking the interaction between the wild-type enzyme and lipids.

In vitro selection of enzymatically active lipase variants from phage libraries using a mechanism-based inhibitor

The 'detergent lipase' Lipolase, from Thermomyces lanuginosa was subjected to a combinatorial protein engineering/phage display approach with the aim of identifying new enzyme variants with improved characteristics in the presence of detergents. First it was demonstrated that wild-type Lipolase could be produced in Escherichia coli retaining full activity and be displayed as an active enzyme fused to coat protein 3 on E. coli phage M13. A phagemid library designed to result in approximately two to three mutations per lipase gene was then constructed. Nine amino acids located in two regions close to the active site were targeted for randomization. Selections using a mechanism-based biotinylated inhibitor showed that phages displaying Lipolase could be specifically enriched from a population of control phages. Selections on a library phage stock in the presence of inhibitor and a commercial powder detergent resulted in a step-wise increase in the proportion of active clones. Analysis of 84 active clones revealed that they all expressed lipase activity, but with lower activities than that of a wild-type Lipolase-producing clone. In six of the seven most active clones a wild-type serine at position 83 had been replaced by threonine, a substitution known to alter the substrate chain length preference of Lipolase variants. Furthermore, the selection had enriched enzyme variants with a high degree of conservatism in one of the variegated regions, suggesting that this region is important for enzymatic activity and that the designed selection procedure was relevant. The selected variants contained primarily basic amino acid residues within the other variegated region. Taken together, the described results show that selection protocols based on enzymatic activity can be designed for this enzyme class which should be of importance for future protein engineering attempts.

Effects of i-propanol on the structural dynamics of Thermomyces lanuginosa lipase revealed by tryptophan fluorescence

Influence of isopropanol (iPrOH) on the structural dynamics of Thermomyces lanuginosa lipase (TLL) was studied by steady-state, time-resolved, and stopped-flow fluorescence spectroscopy, monitoring the intrinsic emission of Trp residues. The fluorescence of the four Trps of the wild-type enzyme report on the global changes of the whole lipase molecule. To monitor the conformational changes in the so-called "lid," an alpha-helical surface loop, the single Trp mutant W89m (W117F, W221H, W260H) was employed. Circular dichroism (CD) spectra revealed that iPrOH does not cause major alterations in the secondary structures of the wild-type TLL and W89m. With increasing [iPrOH], judged by the ratio of emission intensities at 350 nm and 330 nm, the average microenvironment of the Trps in the wild-type TLL became more hydrophobic, whereas Trp89 of W89m moved into a more hydrophilic microenvironment. Time-resolved fluorescence measurements revealed no major changes to be induced by iPrOH neither in the shorter fluorescence lifetime component (tau(1) = 0.5--1.2 ns) for the wild-type TLL nor in the longer fluorescence lifetime component (tau(2) = 4.8--6.0 ns) in the wild-type TLL and the W89m mutant. Instead, for W89m on increasing iPrOH from 25% to 50% the value for tau(1) increased significantly, from 0.43 to 1.5 ns. The shorter correlation time phi(1) of W89m had a minimum of 0.08 ns in 25% iPrOH. Judged from the residual anisotropy r(infinity) the amplitude of the local motion of Trp89 increased upon increasing [iPrOH] 10%. Stopped-flow fluorescence spectroscopy measurements suggested the lid to open within approximately 2 ms upon transfer of W89m into 25% iPrOH. Steady-state anisotropies and longer correlation times revealed increasing concentrations of iPrOH to result also in the formation of dimers as well as possibly also higher oligomers by TLL.

Effect of the lipid interface on the catalytic activity and spectroscopic properties of a fungal lipase

Lipase from the fungi Thermomyces (formerly Humicola) lanuginosa (TlL) is widely used in industry. This interfacial enzyme is inactive under aqueous conditions, but catalytic activation is induced on binding to a lipid-water interface. In order for protein engineering to design more efficient mutants of TlL for specific applications, it is important to characterize its interfacial catalysis. A complete analysis of steady-state kinetics for the hydrolysis of a soluble substrate by TlL has been developed using an interface different from the substrate. Small vesicles of 1-palmitoyl-2-oleoylglycero-sn-3-phosphoglycerol (POPG) or other anionic phospholipids are a neutral diluent interface for the partitioning of substrate and enzyme. TlL binds to these interfaces in an active or open form, thus implying a displacement of the helical lid away from the active site. A study of the influence of substrate and diluent concentration dependence of the rate of hydrolysis provides a basis for the determination of the primary interfacial catalytic parameters. The interfacial activation is not supported by zwitterionic vesicles or by large anionic vesicles of 100 nm diameter, although TlL binds to these interfaces. Using a combination of fluorescence-based techniques applied to several mutants of TlL with different tryptophan residues we have shown that TlL binds to phospholipid vesicles in different forms rendering different catalytic activities, and that the open lid conformation is achieved and stabilized by a combination of electrostatic and hydrophobic interactions between the enzyme's lipid-binding face and the interface.

A mechanism of membrane neutral lipid acquisition by the microsomal triglyceride transfer protein

The microsomal triglyceride transfer protein (MTP) and apolipoprotein B (apoB) belong to the vitellogenin (VTG) family of lipid transfer proteins. MTP is essential for the intracellular assembly and secretion of apoB-containing lipoproteins, the key intravascular lipid transport proteins in vertebrates. We report the predicted three-dimensional structure of the C-terminal lipid binding cavity of MTP, modeled on the crystal structure of the lamprey VTG gene product, lipovitellin. The cavity in MTP resembles those found in the intracellular lipid-binding proteins and bactericidal/permeability-increasing protein. Two conserved helices, designated A and B, at the entrance to the MTP cavity mediate lipid acquisition and binding. Helix A (amino acids 725-736) interacts with membranes in a manner similar to viral fusion peptides. Mutation of helix A blocks the interaction of MTP with phospholipid vesicles containing triglyceride and impairs triglyceride binding. Mutations of helix B (amino acids 781-786) and of N780Y, which causes abetalipoproteinemia, have no impact on the interaction of MTP with phospholipid vesicles but impair triglyceride binding. We propose that insertion of helix A into lipid membranes is necessary for the acquisition of neutral lipids and that helix B is required for their transfer to the lipid binding cavity of MTP.