Microbiological assessment of the implant-abutment interface in different connections: cross-sectional study after 5 years of functional loading

Measurement of gap between abutment and fixture in dental conical connection implants. A focused ion beam SEM observation

BACKGROUND

The aim of the authors was to examine the abutment-fixture interface in Morse-type conical implants in order to verify gaps at this level using a new microscopical approach.

MATERIAL AND METHODS

In this in vitro study, 20 abutment-fixture complexes were prepared by sectioning (longitudinal and cross-sectional to the long axis) with a microtome and then with a focused ion beam (FIB). This is a micrometric machine tool that uses gallium ions to abrade circumscribed areas to dig deeper into the cuts obtained with the microtome in order to eliminate cut-induced artifacts. This is because the FIB abrasion is practically free from artifacts, which are normally generated by the action of the microtome blades or other techniques. Samples were then observed by scanning electron microscopy (SEM).

RESULTS

The observation of the abraded parts with the FIB permitted measurement of the real gap between the implant-abutment components. A variable amount of gap was retrieved (from 0 to 3 μm) by the observations, confirming the non-hermetic nature of the connection. It has to be pointed out that in approximately 65% of cases, the gap accounted for less than 1 μm.

CONCLUSIONS

The reported data confirmed that the analyzed connection system allowed for minimal gap. However, from the evidence of the present analysis, it cannot be assumed that the 2 parts of a Morse-type conical implant are fused in 1 piece, which would create a perfectly matched hermetic connection.

The Impact of Implant-Abutment Connection on Clinical Outcomes and Microbial Colonization: A Narrative Review

INTRODUCTION

Osseointegration are often suffering from oral conditions, especially, the micro gap at the implant-abutment connection represents a site for bacterial plaque aggregation, leading to increased inflammatory cells and causing peri-implantitis.

AIM

The aim of this narrative review was to describe the different kinds of implant-abutment connections and their ability to reduce bacterial leakage and thus prevent peri-implantitis.

MATERIALS AND METHODS

The following databases were consulted: Pubmed, Scopus, Cochrane Library, and Research gate and a total of 528 articles were found. After reading the abstract and titles, 473 items were excluded. The remaining articles (n = 55) were assessed for full-text eligibility. Thirty-three studies were included in the review.

RESULTS AND CONCLUSIONS

We selected 22 clinical trials and 11 reviews, examining a total sample of 2110 implants. From the review, it was clear that there exists a relationship between the implant-abutment interface and bacterial leakage. All the connections presented an amount of micro-gap and bacterial micro-leakage, though conical and mixed connection systems seemed to behave better. Moreover, both connections seemed to have a better load distribution and the mixed system also had anti-rotational properties which are very useful during the positioning of the prosthesis.

Candida albicans biofilms on different materials for manufacturing implant abutments and prostheses

BACKGROUND

Morphological, physical and chemical properties of both implants and prostheses can determine the biofilm formation on their surface and increase the risk of biological complications. The aim of this study was to evaluate the capacity of biofilm formation of Candida albicans on different materials used to manufacture abutments and prostheses.

MATERIAL AND METHODS

Biofilm formation was analyzed on cp grade II titanium, cobalt-chromium alloy and zirconia, silicone, acrylic resin (polymethylmethacrylate) and nano-hybrid composite. Some samples were partially covered with lithium disilicate glass ceramic to study specifically the junction areas.C. albicans was incubated in a biofilm reactor at 37 °C with agitation. The biofilm formation was evaluated at 24 and 48 hours. In addition, the morphology of the biofilm was evaluated by scanning electron microscopy.

RESULTS

C. albicans developed biofilms on the surface of all materials tested. Cobalt-chromium alloy showed the lowest density of adhered biofilm, followed by zirconia and titanium. Silicone and resin showed up to 20 times higher density of biofilm. A higher biofilm formation was observed when junctions of materials presented micropores or imperfections.

CONCLUSIONS

The biofilm formed in the three materials used in the manufacture of abutments and prostheses showed no major differences, being far less dense than in the resins. Two clinical recommendations can be made: to avoid the presence of resins in the subgingival area of implant prostheses and to design prostheses placing cobalt-chromium alloy/ceramic or titanium/ceramic junctions as far as possible from implants.

Sealing agent reduces formation of single and dual-species biofilms of Candida albicans and Enterococcus faecalis on screw joints at the abutment/implant interface

The aim of this research was to evaluate the efficacy of a commercial sealing agent at the abutment/implant interface against microleakage of single and dual-species biofilms of Candida albicans and Enterococcus faecalis into external hexagon (EH) and Morse taper (MT) prosthetic connections. A total of 216 samples of implants and their abutments were tested. Six groups (n = 36) were evaluated based on biofilm and period of incubation (7 and 14 days). The implant connections EH and MT (n = 18) were divided according to the use of the material (n = 9) (EH-T and MT-T: with the sealing agent; EH-C and MT-C: control). The biofilms were analyzed by microbial counting (CFU/mL) and SEM analysis and photographs of the material in the screw joints were also taken. Data were analyzed by Student t test, two-way ANOVA and Bonferroni test. For the single-species biofilms, there was a significant reduction in the growth of E. faecalis when compared MT-C and MT-T or EH-C and EH-T at 7 and 14 days. The same was observed for C. albicans biofilms. For dual-species biofilms of E. faecalis and C. albicans, the sealing agent was more effective in preventing microbial infiltration into the MT connection at 14 days, while microbial infiltration did not occur into EH connections even in absence of the sealing agent for both periods of evaluation. Overall, these data suggest that the presence of the sealing agent reduces or eliminates the microleakage of E. faecalis and C. albicans biofilms into the implants regardless of the period of incubation.

Bacterial Profile and Radiographic Analysis Around Osseointegrated Implants With Morse Taper and External Hexagon Connections: Split-Mouth Model

The aim of this clinical study was to evaluate bacterial colonization, marginal bone loss, and optical alveolar density in implants with Morse taper (MT) and external hexagon (EH) connections. Thirty-five implants were installed in 7 patients (mean age: 65.8 ± 6.7 years). Implants were divided into 2 groups, according to platform design: G1 - MT, installed 2mm infra-osseous and G2 - EH, positioned according to Branemark protocol. Patients were evaluated at baseline (T0), 21 days (T1), 3 months (T2), 6 months (T3), and 12 months (T4) after installations. Bone loss and alveolar density were evaluated by standardized periapical radiographs and bacterial profile with checkerboard DNA-DNA hybridization. Statistical analyses were performed using SPSS 23.0. To present the results, boxplots and a line graph of mean were used. P-values ≤ .05 were statistically significant. After 3 months, alveolar bone loss was significantly higher in the G2 (T2-T0: P = .006; T3-T0: P = .003; and T4-T0: P = .005). No significant differences between G1 and G2 groups were observed for optical alveolar density. Microbiological analysis showed similar profiles between studied groups; however, there were significantly higher counts of Tannerella forsythia (P = .048), Campylobacter showae (P = .038), and Actinomyces naeslundii (P = .027) in G1 after 12 months. Based on the results of this study, it can be concluded that there was less peri-implant bone loss in MT compared to EH connections, but microbiological profile did not seem to influence bone changes.

In Vitro Comparison of Microbial Leakage of the Implant-Healing Abutment Interface in Four Connection Systems

This study sought to assess microbial leakage through the implant-healing abutment interface in 4 dental implant connection systems. Ten implants of each of the 3i (double hexagon + flat to flat; group 1), IDI (internal hexagon + Morse taper; group 2), Swiss Plus (external bevel + internal octagon; group 3), and Tapered Screw-Vent (internal bevel + internal hexagon; group 4) systems were used in this in vitro, experimental study. Healing abutments were screwed to the implants with 10 Ncm torque. Implants were immersed in Escherichia coli suspension for 24 hours. Samples were taken of the internal surface of implants and cultured. The number of grown colonies was counted after 24 hours of culture and after 7 and 14 days of immersion in microbial suspension. The same was repeated with healing abutments torqued to 10 and 20 Ncm. With 10 Ncm torque, all specimens in all groups showed microleakage at one day with the highest microleakage in one sample in group 3. At 7 days, the highest microleakage was noted in one specimen in group 2. With 20 Ncm torque, group 3 showed significantly higher microleakage than other groups at 1 and 7 days (P < .05). Increasing the torque decreased microleakage in all groups except for group 3. Microbial leakage occurred in almost all implant systems in our study. In one-stage implant placement, healing abutments should be preferably torqued to 20 Ncm to minimize microleakage. Optimal torque for healing abutment insertion should be analyzed individually for each system.

Innovation by Computer-Aided Design/Computer-Aided Manufacturing Technology: A Look at Infection Prevention in Dental Settings

Recent data indicates limited awareness and compliance on infection prevention procedures by dental offices and by dental laboratories. Guidelines for infection prevention in dentistry have been published by Centres for Disease Control and Prevention since 2003; the section “IX-Special consideration” includes a subsection concerning the prevention in dental laboratories, but it has not been modernised in later versions to fit the needs of traditional and computer-aided technology. Traditional techniques required disinfecting items (impression, chewing waxes, and appliances) with well-suited products, which are also chosen for limiting impression changes or appliance deterioration. Effective procedures are available with difficulties. Some of these contain irritant or non-eco-friendly disinfectants. The transport of impression, to dental laboratories, is often delayed with limited precautions for limiting cross-infection. Gypsum casts are frequently contaminated mainly by bacteria and their antibiotic-resistant strains and even stored for long periods during dental implant supported restoration and orthodontic therapy, becoming a hidden source of infection. Nowadays, computer-aided design/computer-aided manufacturing technology seems to be an interesting way to promote both business and safety, being more comfortable for patients and more accurate than traditional technology. A further advantage is easier infection prevention since, for the most part, mainly digital impression and casts are not a source of cross-infection and the transport of contaminated items is reduced and limited to try-in stages. Nevertheless, a peculiar feature is that a digital electronic file is of course unalterable, but may be ruined by a computer virus. Additionally, the reconditioning of scanner tips is determinant for the optical characteristics and long term use of the scanner, but information for its reconditioning from producers is often limited. This study focuses on some critical points including (a) insufficient guidelines, (b) choice of proper procedure for scanner reconditioning, and (c) data protection in relation to patient privacy.

Effect of Implant-Abutment Connection Type on Bone Around Dental Implants in Long-Term Observation: Internal Cone Versus Internal Hex

PURPOSE

The purpose of this study was to evaluate the influence of the implant-abutment connection type on the bone level around dental implants in long-term observation and the survival rate for the different types of implant-abutment connections.

MATERIALS AND METHODS

Two groups of implants made of titanium grade 23 alloy and with sandblasted and acid-etched (SLA) surface were included in the study: (a) the internal hex implant-abutment connection group (480 SPI dental implants; Alpha-Bio Tec, Petach Tikwa, Israel, 184 patients) and (b) the internal cone implant-abutment connection group (60 C1 dental implants; MIS Implant Technologies, Shlomi, Israel, 34 patients). Certain inclusion and exclusion criteria were applied. Marginal bone loss (MBL) around the dental implants was measured in intraoral radiographs taken with parallel technique with a film holder and by bite recording index. X-rays were performed at the moment of functional loading, and at 12, 24, 36, and 60 months after loading. The digital analysis was conducted using Dental Studio 2.0 computer software.

RESULTS

Average MBL was significantly lower in the conical connection compared with internal hex group-0.68 ± 0.59 versus 0.99 ± 0.89 mm (12 months), 0.78 ± 0.80 versus 1.12 ± 1.00 mm (24 months), 0.83 ± 0.87 versus 1.22 ± 1.03 mm (36 months), and 0.96 ± 1.02 versus 1.30 ± 1.15 mm (60 months after loading). Both groups of implants achieved a 100% survival rate.

CONCLUSION

The internal cone connection reduced bone resorption compared with the internal hex. Both groups of implants had a 100% survival rate.

Efficacy of a Polyglycol Dimethacrylate-Based Adhesive in Sealing the Implant-Abutment Interface

PURPOSE

The purpose of this study was to assess the effectiveness of a polyglycol dimethacrylate-based adhesive in preventing bacterial leakage through implant-abutment interfaces (IAIs).

MATERIALS AND METHODS

After implant installation, the adhesive was applied in the experimental group (n = 10). None was applied in the control group (n = 10). Samples were collected from the inner walls of implants on days 0 and 90. The real-time polymerase chain reaction was used to detect bacterial DNA.

RESULTS

All samples from the control group, versus 30% from the experimental group, harbored bacterial DNA on day 90.

CONCLUSIONS

This polyglycol dimethacrylate-based adhesive may be used to seal the IAI. Further studies are warranted to verify its effectiveness over longer time periods.

Contact analysis of gap formation at dental implant-abutment interface under oblique loading: A numerical-experimental study

PURPOSE

To develop numerical and experimental methods for investigating the formation of micro-gaps and the change in contact area at the implant-abutment interface of two different connector designs under oblique cyclic loading.

MATERIALS AND METHODS

Samples (n = 10 per group) of two-piece implant systems with the conical connection (group A) and the external hexagonal connection (group B) were subjected to cyclic loading with increasing load amplitudes up to 220 N. After loading, the samples were scanned using micro-CT, with silver nitrate as a high-contrast penetrant, and the level of leakage was assessed using a discrete scoring system. Three-dimensional finite element (FE) analyses of the two implant systems were also conducted to reveal the micro-gap formation process, especially bridging of the internal abutment screw space. The experimental and numerical results for the bridging load were then compared.

RESULTS

90% of the samples in group A showed leakage into the internal implant space at a load of around 100 N; while over 80% of those in group B did so at a load of around 40 N. This agreed with the FE analysis, which showed bridging of the internal implant space at loads similar to those measured for the two implant systems. Residual gaps of less than 1.49 μm were predicted for group A only after unloading.

CONCLUSIONS

The FE-predicted loads for bridging agreed well with those found experimentally for leakage to occur. The conical connection showed more resistance against formation of micro-gaps at the implant-abutment interface than the external hexagonal connection. Although the minimum load required to bridge the internal implant space was within the range of human biting force, the relation between bacterial invasion and micro-gaps needs further research.

Mechanical Outcomes, Microleakage, and Marginal Accuracy at the Implant-Abutment Interface of Original versus Nonoriginal Implant Abutments: A Systematic Review of In Vitro Studies

Purpose

Instead of original abutments, compatible abutments are often selected for financial reasons. The present study aimed to evaluate mechanical outcomes, microleakage, and marginal accuracy at the implant-abutment interface of original versus nonoriginal implant abutments.

Study Selection

Search strategy encompassed literature from 1967 up to March 2017 to identify relevant studies meeting the inclusion criteria. The following electronic databases were consulted: PubMed database of the U.S. National Library of Medicine, Embase (Excerpta Medica dataBASE), and the Grey Literature Database (New York Academy of Medicine Grey Literature Report). Quality assessment of the full-text articles selected was performed. Abutments were classified in original (produced by the same implant manufacturer), nonoriginal certified (produced by a third-party milling center, certified by implant companies), and nonoriginal compatible (produced by a third-party milling center for similar connections).

Results

A total of 16 articles fulfilled inclusion criteria and quality assessment and were selected for the qualitative analysis. All of the included studies were in vitro research with high or moderate risk of bias and reported data from 653 implant abutments. Original and nonoriginal certified abutments showed better results in terms of mechanical outcomes, microleakage, and marginal accuracy compared to nonoriginal compatible abutments.

Conclusions

Following the clear warnings coming from the present systematic review, clinical suggestions regarding the effect of a nonoriginal abutment can be drawn. However, in vivo, long-term, randomized controlled trials are needed to provide definitive clinical conclusion about the long-term clinical outcomes of original and nonoriginal abutments.

Soft Tissue Contour Impression with Analogic or Digital Work Flow: A Case Report

Purpose: Transferring precise information to the dental laboratory is one of the key factors to achieving clinical success. The aim of the present study was to describe classical and digital work-flows used to rehabilitate an implant with a convergent collar in the aesthetic zone following the BOPT (biologically oriented preparation technique) approach and to report the three years follow-up outcomes of two patients rehabilitated following such procedures. Materials and methods: Two central incisors of two different patients were rehabilitated with a tissue-level implant with a convergent collar and, after a provisional and healing phase, one implant was “impressed” using a classical workflow and one using a digital one. The primary outcome measured was the mean bone loss. An intraoral radiograph was taken at crown delivery and at the three years follow-up visit. Secondary Esthetic outcomes pre-op and post-op were evaluated using the PES (pink esthetic score). Results: At the three years follow-up visit, radiographic analysis showed no signs of bone resorption. For the analogic procedure, the pre-and post-op PES scores were 8, whereas for the digital procedure the pre-op PES score was 4 and a post-op score of 9 was obtained. Conclusions: classical and digital work flows succeeded in giving precise and complete anatomical information of implant position, including the soft tissue contour. Minimum bone loss and an esthetic success were obtained in both procedures.

Influence of Luting Materials on the Retention of Cemented Implant-Supported Crowns: An In Vitro Study

The retention force of cemented crowns on implant abutments with various luting materials was evaluated. Cobalt⁻chromium crowns were cemented onto tapered titanium abutments (Camlog) with eugenol-free temporary cement (RelyX TempBond NE), composite-based temporary cement (Bifix Temp), zinc phosphate cement (Harvard Cement), glass-ionomer cements (Meron, Fuji I), and resin-modified glass-ionomer cements (Fuji II, Fuji Plus, Ketac Cem Plus). Specimen aging via hydrostress was performed in artificial saliva at 37 °C for 14 days (S1), followed by hydrothermal stress with thermocycling (S2). The crowns were removed, and the force was recorded (T1). Subsequently, the crowns were recemented, aged, and removed, and the force was recorded (T2, T3). The retention forces differences were statistically significant according to the storage conditions at T1 (p = 0.002) and T3 (p = 0.0002). After aging (S1), Ketac Cem Plus had the highest retention force median value difference (T3 versus T1) (-773 N), whereas RelyX TempBond NE had the lowest (-146 N). After aging (S2), Meron had the highest retention force median value difference (-783 N), whereas RelyX TempBond NE had the lowest (-168 N). Recementation decreased the retention force of the implant-supported cobalt⁻chromium crowns cemented and recemented with the same luting materials. Luting materials (at T1) and aging conditions significantly impacted the retention force.

Diagnostic accuracy of 4 intraoral radiographic techniques for misfit detection at the implant abutment joint

STATEMENT OF PROBLEM

A misfit or gap at the implant-abutment joint (IAJ) requires detection as it may compromise the health of the peri-implant tissue. However, which radiographic technique provides the most orthogonal relationship between the central beam and the implant/image receptor is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the diagnostic accuracy of 4 intraoral radiographic techniques on misfit detection at the IAJ.

MATERIAL AND METHODS

Twenty implants were placed in polyamide jaws, and customized dental implant abutments with a metal collar were installed. Different gaps were simulated by placing one or three 50-μm-thick polyester strips at the IAJ; the absence of the strip represented the control group (no gap). The 4 radiographic techniques were evaluated by using different film holders: a periapical with bisecting angle (PBA), a bitewing interproximal (BI), a periapical with standard paralleling (PSP), and a periapical with modified paralleling (PMP) holder (with a custom-made paralleling index). A total of 240 digital radiographs were evaluated by 4 clinicians experienced with dental implants. Differences were evaluated by using receiver operating characteristic (ROC) curves (Az) and Fisher tests (α=.05). Diagnostic values (sensitivity, specificity, accuracy, and positive and negative predictive values) were also obtained. The Kappa test was used to assess intra- and interevaluator reproducibility, which ranged from moderate to almost perfect.

RESULTS

All diagnostic values, except specificity, were lower for the PBA technique for both the 50- and 150-μm gaps. Az values for the PBA technique were significantly lower than those obtained for the other 3 techniques (P<.05), which did not differ from each other. The 150-μm gaps were more easily detected than the 50-μm gaps only for PBA (P<.05).

CONCLUSIONS

The BI, PSP, and PMP techniques detected misfits at the IAJ most accurately. The PBA technique is not recommended for this purpose.

Antimicrobial Efficacy of Materials Used for Sealing the Implant Abutment Screw Hole: An In Vitro Evaluation

AIM

The aim of this in vitro study was to assess the antimicrobial efficacy of materials (gutta percha [GP], polytetrafluoroethylene [PTFE] tape, and vinyl polysiloxane [VP]) used for sealing the implant abutment screw hole (IASH).

METHODS

Sixty implants with a Morse cone connection were used. The implants were randomly divided into 3 groups (20 implants/group). In groups 1, 2, and 3, the IASH was sealed with GP, PTFE, and VP, respectively. Unstimulated whole saliva (UWS) was used as a contaminant medium for the incubation of the specimens. After 7 days of incubation, the specimens were opened under aseptic conditions, and the contents of the inner parts of the IASH were collected using sterile microbrushes. The occurrence of microbial leakage through the screw access channel interface was assessed with the checkerboard DNA-DNA hybridization method. P < 0.05 was considered statistically significant.

RESULTS

Among samples in groups 1, 2, and 3, the UWS collected before incubation showed no statistically significant differences in relation to the prevalence of species investigated. Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis, Treponema denticola, Tannerella forsythia, and Candida albicans were isolated from group 1 than groups 2 and 3.

CONCLUSION

The choice of material for sealing the IASH is entirely dependent on the operators' choice and experience.

Novel expandable short dental implants in situations with reduced vertical bone height-technical note and first results

PURPOSE

Short implants often have the disadvantage of reduced primary stability. The present study was conducted to evaluate the feasibility and safety of a new expandable short dental implant system intended to increase primary stability.

METHODS

As a "proof of concept", a prospective clinical cohort study was designed to investigate intraoperative handling, primary and secondary implant stability (resonance frequency analysis), crestal bone changes, implant survival and implant success, of an innovative short expandable screw implant. From 2014 until 2015, 9 patients (7-9-mm vertical bone height) with 30 implants (length 5-7 mm, diameter 3.75-4.1 mm) were recruited consecutively.

RESULTS

All 30 implants in the 9 patients (age 44 to 80 years) could be inserted and expanded without intraoperative problems. Over the 3-year follow-up period, the implant success rate was 28/30 (93.3%). The mean implant stability quotients (ISQ) were as follows: primary stability, 69.7 ± 10.3 ISQ units, and secondary stability, 69.8 ± 10.2 ISQ units (p = 0.780), both without significant differences between the maxilla and mandible (p ≥ 0.780). The mean crestal bone changes after loading were (each measured from the baseline) as follows: in the first year, 1.0 ± 0.9 mm in the maxilla and 0.7 ± 0.4 mm in the mandible, and in the second year, 1.3 ± 0.8 mm and 1.0 ± 0.7 mm, respectively.

CONCLUSIONS

Compared to other prospective studies, in this indication, the success rate is acceptable. Implant stability shows high initial and secondary stability values. The system might present an extension of functional rehabilitation to the group of elderly patients with limited vertical bone height. Further long-term investigations should directly compare this compressive implant with standard short implants.

Investigation of peri-implant tissue conditions and peri-implant tissue stability in implants placed with simultaneous augmentation procedure: a 3-year retrospective follow-up analysis of a newly developed bone level implant system

Background

Guided bone regeneration (GBR) has been proven to be a reliable therapy to regenerate missing bone in cases of atrophy of the alveolar crest. The aim of the present retrospective analysis was to assess peri-implant tissue conditions and document peri-implant tissue stability in C-Tech implants when placed simultaneously with a GBR augmentation procedure.

Methods

A total of 47 implants, which were placed simultaneously with a GBR procedure with a synthetic bone substitute material in 20 patients, were investigated clinically and radiologically at least 3 years after loading. Implant survival, the width and thickness of peri-implant keratinized gingiva, probing depth, bleeding on probing (BOP), the Pink Esthetic Score (PES), peri-implant bone loss, and the presence of peri-implant osteolysis were determined.

Results

The follow-up investigation revealed a survival rate of 100% and only low median rates for probing depths (2.7 mm) and BOP (30%). The mean PES was 10.1 from the maximum value of 14. No osseous peri-implant defects were obvious, and the mean bone loss was 0.55 mm.

Conclusions

In conclusion, implants placed in combination with a GBR procedure can achieve long-term stable functionally and esthetically satisfying results for replacing missing teeth in cases of atrophy of the alveolar crest.

Microleakage at the Different Implant Abutment Interface: A Systematic Review

INTRODUCTION

Presence of gap at the implant-abutment interface, leads to microleakage and accumulation of bacteria which can affect the success of dental implants.

AIM

To evaluate the sealing capability of different implant connections against microleakage.

MATERIALS AND METHODS

In January 2017 an electronic search of literature was performed, in Medline, EBSCO host and Pubmed data base. The search was focused on ability of different implant connections in preventing microleakage. The related titles and abstracts available in English were screened, and the articles that fulfilled the inclusion criteria were selected for full text reading.

RESULTS

In this systematic review, literature search initially resulted in 78 articles among which 30 articles only fulfilled the criteria for inclusion and were finally included in the review. Almost all the studies showed that there was some amount of microleakage at abutment implant interface. Microleakage was very less in Morse taper implants in comparison to other implant connections. Majority of studies showed less microleakage in static loading conditions and microleakage increases in dynamic loading conditions.

CONCLUSION

In this systematic review maximum studies showed that there was some amount of microleakage at abutment implant interface. External hexagon implants failed completely to prevent microleakage in both static and dynamic loading conditions of implants. Internal hexagon implants mainly internal conical (Morse taper) implants are very promising in case of static loading and also showed less microleakage in dynamic loading conditions. Torque recommended by manufacturer should be followed strictly to get a better seal at abutment implant interface. Zirconia abutments are more to microleakage than Titanium abutments and there use should be discouraged. Zirconia abutments should be only restricted to cases where there was very high demand of aesthetics.

Microbial colonization at the implant-abutment interface and its possible influence on periimplantitis: A systematic review and meta-analysis

PURPOSE

The aim of this systematic review and meta-analysis was to evaluate the microbial colonization at the implant-abutment interfaces (IAI) on bone-level implants and to identify possible association with peri-implant conditions.

STUDY SELECTION

The focus question aimed to answer whether two-piece osseointegrated implants, in function for at least 1 year, in human, relate to higher bacterial count and the onset of periimplantitis, compared to healthy peri-implant conditions. Search strategy encompassed the on-line (MedLine, Google scholar, Cochrane library) literature from 1990 up to March 2015 published in English using combinations of MeSH (Medical Subject Headings) and search terms. Quality assessment of selected full-text articles was performed according to the ARRIVE and CONSORT statement guidelines. For data analysis, the total bacterial count of Porphyromonas gingivalis, Tannerella forsythia, Treponema denticola, Prevotella intermedia, and Fusobacterium nucleatum was calculated and compared to IAI with or without peri-implant pathology.

RESULTS

A total of 14 articles, reporting data from 1126 implants, fulfilled the inclusion criteria and subjected to quality assessment. The selected studies revealed contamination of the IAI, in patients who received two-piece implant systems. Meta-analysis indicated significant difference in total bacterial count between implants affected by periimplantitis versus healthy peri-implant tissues (0.387±0.055; 95% CI 0.279-0.496). Less bacterial counts were identified in the healthy IAI for all the investigated gram-negative bacteria except for T. forsythia.

CONCLUSIONS

Significantly higher bacterial counts were found for periodontal pathogenic bacteria within the IAI of implants in patients with periimplantitis compared to those implants surrounded by healthy peri-implant tissues.

In Vitro Microbiological Analysis of Bacterial Seal in Hybrid Zirconia Abutment Tapered Connection

PURPOSE

The aim of this study was to evaluate the bacterial seal at the implant-hybrid zirconia abutment interface and Morse taper-type connections through in vitro microbiological analysis.

MATERIALS AND METHODS

Sixteen implants and their respective abutments were divided into 3 groups: test (10 sets), positive control (3 sets), and negative control (3 sets). In the test group, 10 implants were contaminated with Escherichia coli using a sterile inoculating loop to the inner portion of the implants, followed by torque application to the abutment (30 N·cm). The positive controls were also contaminated, but no torque was applied to the abutment screw. The negative control consisted of uncontaminated sets. All specimens were immersed in test tubes containing 5 mL brain heart infusion (BHI) broth, maintained in a microbiological incubator for 14 days at 37°C under aerobic conditions, and monitored every 24 hours for evidence of bacterial growth.

RESULTS

During the 14 days of incubation, no significant increase in the number of cloudy culture media was observed in the test group (P = 0.448). No significant difference in broth turbidity ratio was observed (P > 0.05).

CONCLUSION

Hybrid zirconia abutments can create an effective seal at the tapered abutment-implant interface with a 30-N·cm installation torque.

The predictive value of microbiological findings on teeth, internal and external implant portions in clinical decision making

AIM

The primary aim of this study was to evaluate 23 pathogens associated with peri-implantitis at inner part of implant connections, in peri-implant and periodontal pockets between patients suffering peri-implantitis and participants with healthy peri-implant tissues; the secondary aim was to estimate the predictive value of microbiological profile in patients wearing dental implants using data mining methods.

MATERIAL AND METHODS

Fifty participants included in the present case─control study were scheduled for collection of plaque samples from the peri-implant pockets, internal connection, and periodontal pocket. Real-time polymerase chain reaction was performed to quantify 23 pathogens. Three predictive models were developed using C4.5 decision trees to estimate the predictive value of microbiological profile between three experimental sites.

RESULTS

The final sample included 47 patients (22 healthy controls and 25 diseased cases), 90 implants (43 with healthy peri-implant tissues and 47 affected by peri-implantitis). Total and mean pathogen counts at inner portions of the implant connection, in peri-implant and periodontal pockets were generally increased in peri-implantitis patients when compared to healthy controls. The inner portion of the implant connection, the periodontal pocket and peri-implant pocket, respectively, presented a predictive value of microbiologic profile of 82.78%, 94.31%, and 97.5% of accuracy.

CONCLUSION

This study showed that microbiological profile at all three experimental sites is differently characterized between patients suffering peri-implantitis and healthy controls. Data mining analysis identified Parvimonas micra as a highly accurate predictor of peri-implantitis when present in peri-implant pocket while this method generally seems to be promising for diagnosis of such complex infections.

Abutment Coating With Diamond-Like Carbon Films to Reduce Implant-Abutment Bacterial Leakage

BACKGROUND

The influence of diamond-like carbon (DLC) films on bacterial leakage through the interface between abutments and dental implants of external hexagon (EH) and internal hexagon (IH) designs was evaluated.

METHODS

Film deposition was performed by plasma-enhanced chemical vapor deposition. Sets of implants and abutments (n = 30 per group, sets of 180 implants) were divided according to connection design and treatment of the abutment base: 1) no treatment (control); 2) DLC film deposition; and 3) Ag-DLC film deposition. Under sterile conditions, 1 μL Enterococcus faecalis was inoculated inside the implants, and abutments were tightened. The sets were tested for immediate external contamination, suspended in test tubes containing sterile culture broth, and followed for 5 days. Turbidity of the broth indicated bacterial leakage. At the end of the period, the abutments were removed and the internal content of the implants was collected with paper points and plated in Petri dishes. After 24-hour incubation, they were assessed for bacterial viability and colony-forming unit counting. Bacterial leakage was analyzed by χ(2) and Fisher exact tests (α = 5%).

RESULTS

The percentage of bacterial leakage was 16.09% for EH implants and 80.71% for IH implants (P <0.0001). The bacterial load was higher inside IH implants (P = 0.000). The type of implant significantly influenced the results (P = 0.000), whereas the films did not (P = 0.487).

CONCLUSION

IH implants show a higher frequency of bacterial leakage; and DLC and Ag-DLC films do not significantly reduce the frequency of bacterial leakage and bacteria load inside the implants.

Microbial Leakage at the Implant-Abutment Connection Due to Implant Insertion Maneuvers: Cross-Sectional Study 5 Years Postloading in Healthy Patients

The aim of this study was to test if stress on the prosthetic connection during insertion maneuvers can induce micro-warping at the implant connection. From September 2011 to July 2013, patients with implants loaded for at least 5 years that were placed with 2 different insertion implant mounters-MP (conventional) and ME (mountless)-were selected from all of those who had received dental implant therapy in the past and were attending routine check-up or spontaneous visits during the study period. Samples were obtained from inside the connection and the abutment surface using absorbent sterile paper tips. Quantitative real-time polymerase chain reaction was performed for total bacterial counts and loads of Aggregatibacter actinomycetemcomitans (Aa), Porphyromonas gingivalis (Pg), Tannerella forsythensis (Tf), Treponema denticola (Td), Prevotella intermedia (Pi), Peptostreptococcus micros (Pm), Fusobacterium nucleatum (Fn), Campylobacter rectus (Cr), Eikenella corrodens (Ec), and Candida albicans (Ca). The analysis of variance test was used to test for differences. Nine patients (20 implants) were included in the MP group and 5 patients (10 implants) in the ME group. Regarding the red complex, Tf was seen in 80% and 30% of MP and ME implants, respectively (P < .001). Significant differences were also found in microbial load. For Td, proportions were 45% vs 10% (P = .022), with no significant differences at load levels. Regarding the orange complex, higher prevalence values were found in MP implants, although differences were nonsignificant. Microbial load levels for orange complex bacteria were higher for MP than ME, and these differences were statistically significant for Fn (4.94 vs 3.09; P = .001). Finally, Ec was detected only in the MP group, and Ca and Aa were not found in either group. Within its limitation (small sample size, retrospective analysis, indirect measurement method), the present study suggests that a mounter not affecting the prosthetic connection should be used to reduce microbial contamination of implants.