Functionalized graphene sheets for polymer nanocomposites

A simple route to enhance the interface between graphite oxide nanoplatelets and a semi-crystalline polymer for stress transfer

This report shows that thermal treatment is a simple and effective approach to create a polymer crystalline layer on the surface of graphite oxide nanoplatelets (GONPs) in polycaprolactone (PCL) melts. It was found that the crystallization temperature of the PCL increased significantly by nearly 9 degrees C with the incorporation of 2 wt% GONPs. As the composite melts isothermally crystallized at the temperature that was 14 degrees C higher than the crystallization temperature, the polymer crystalline layer was optimized on the surface of the GONPs. At 2 wt% GONPs, the Young's modulus of the composite was nearly 1.5 times greater than for the pure PCL. In comparison with untreated composites, the improvement in the Young's modulus of treated composites nearly doubled. It confirmed that a non-covalent interface for stress transfer can be enhanced by the formation of the polymer crystalline layer bridging the GONPs and the polymer matrix.

Fabrication of Graphene/Polyaniline Composite Paper via In Situ Anodic Electropolymerization for High-Performance Flexible Electrode

Freestanding and flexible graphene/polyaniline composite paper was prepared by an in situ anodic electropolymerization of polyaniline film on graphene paper. This graphene-based composite paper electrode, consisting of graphene/polyaniline composite sheets as building blocks, shows a favorable tensile strength of 12.6 MPa and a stable large electrochemical capacitance (233 F g(-1) and 135 F cm(-3) for gravimetric and volumetric capacitances), which outperforms many other currently available carbon-based flexible electrodes and is hence particularly promising for flexible supercapacitors.

Extraordinary synergy in the mechanical properties of polymer matrix composites reinforced with 2 nanocarbons

One of the applications of nanomaterials is as reinforcements in composites, wherein small additions of nanomaterials lead to large enhancements in mechanical properties. There have been extensive studies in the literature on composites where a polymer matrix is reinforced by a single nanomaterial such as carbon nanotubes. In this article, we examine the significant synergistic effects observed when 2 different types of nanocarbons are incorporated in a polymer matrix. Thus, binary combinations of nanodiamond, few-layer graphene, and single-walled nanotubes have been used to reinforce polyvinyl alcohol. The mechanical properties of the resulting composites, evaluated by the nanoindentation technique, show extraordinary synergy, improving the stiffness and hardness by as much as 400% compared to those obtained with single nanocarbon reinforcements. These results suggest a way of designing advanced materials with extraordinary mechanical properties by incorporating small amounts of 2 nanomaterials such as graphene plus nanodiamond or nanodiamond plus carbon nanotube.

Layer-by-layer self-assembly of graphene nanoplatelets

In this report, graphene nanoplatelets were self-assembled through the layer-by-layer (LBL) method. The graphene surface was modified with poly(acrylic acid) and poly(acryl amide) by covalent bonding, which introduced negative and positive charge on the surface of graphene, respectively. Through electrostatic interaction, the positively and negatively charged graphene nanoplatelets assembled together to form a multilayer structure. Thermogravimetric analysis, Raman spectroscopy, scanning electron microscopy (SEM), and atomic force microscopy were used to demonstrate the modification of graphene nanoplatelets. Fourier transform infrared spectroscopy and SEM proved this method is feasible for preparing graphene-containing films. Ultraviolet-visible spectroscopy confirmed that the adsorption technique resulted in uniform film growth.

Atomic force and scanning tunneling microscopy imaging of graphene nanosheets derived from graphite oxide

Graphene nanosheets produced in the form of stable aqueous dispersions by chemical reduction of graphene oxide and deposited onto graphite substrates have been investigated by atomic force and scanning tunneling microscopy (AFM/STM). The chemically reduced graphene oxide nanosheets were hardly distinguishable from their unreduced counterparts in the topographic AFM images. However, they could be readily discriminated through phase imaging in the attractive regime of tapping-mode AFM, probably because of differences in hydrophilicity arising from their distinct oxygen contents. The chemically reduced nanosheets displayed a smoothly undulated, globular morphology on the nanometer scale, with typical vertical variations in the subnanometer range and lateral feature sizes of approximately 5-10 nm. Such morphology was attributed to be the result of significant structural disorder in the carbon skeleton, which originates during the strong oxidation that leads to graphene oxide and remains after chemical reduction. Direct evidence of structural disorder was provided by atomic-scale STM imaging, which revealed an absence of long-range periodicity in the graphene nanosheets. Only structured domains a few nanometers large were observed instead. Likewise, the nanosheet edges appeared atomically rough and ill-defined, though smooth on the nanometer scale. The unreduced graphene oxide nanosheets could only be imaged by STM at very low tunneling currents (approximately 1 pA), being visualized in some cases with inverted contrast relative to the graphite substrate, a result that was attributed to their extremely low conductivity. Complementary characterization of the unreduced and chemically reduced nanosheets was carried out by thermogravimetric analysis as well as UV-visible absorption and X-ray photoelectron and Raman spectroscopies. In particular, the somewhat puzzling Raman results were interpreted to be the result of an amorphous character of the graphene oxide material.

Real-time study of graphene's phase transition in polymer matrices

We present real-time study of pristine graphene sandwiched in a homogeneous polymer matrix and its phase transition where the graphene membrane irreversibly scrolls and folds above the polymer's glass temperature. Tubular structures tend to form by curling up from edge defects of graphene and roll along its surface. A single-layer can also fold into two- or three-layer stacks and the overlapping between layers extends along the membrane surface to enlarge up to micrometer sizes. Further, oxidized graphene does not show such reactivity at even higher temperatures, indicating that the intrinsic thermal instability of pristine graphene in the polymer matrix is the origin of the transition.

Self-assembled TiO2-graphene hybrid nanostructures for enhanced Li-ion insertion

We used anionic sulfate surfactants to assist the stabilization of graphene in aqueous solutions and facilitate the self-assembly of in situ grown nanocrystalline TiO2, rutile and anatase, with graphene. These nanostructured TiO2-graphene hybrid materials were used for investigation of Li-ion insertion properties. The hybrid materials showed significantly enhanced Li-ion insertion/extraction in TiO2. The specific capacity was more than doubled at high charge rates, as compared with the pure TiO2 phase. The improved capacity at high charge-discharge rate may be attributed to increased electrode conductivity in the presence of a percolated graphene network embedded into the metal oxide electrodes.

Chemical methods for the production of graphenes

Interest in graphene centres on its excellent mechanical, electrical, thermal and optical properties, its very high specific surface area, and our ability to influence these properties through chemical functionalization. There are a number of methods for generating graphene and chemically modified graphene from graphite and derivatives of graphite, each with different advantages and disadvantages. Here we review the use of colloidal suspensions to produce new materials composed of graphene and chemically modified graphene. This approach is both versatile and scalable, and is adaptable to a wide variety of applications.

Colloidal suspensions of highly reduced graphene oxide in a wide variety of organic solvents

We report that homogeneous colloidal suspensions of chemically modified graphene sheets were readily produced in a wide variety of organic solvent systems. Two different sets of solubility parameters are used to rationalize when stable colloidal suspensions of graphene oxide sheets and, separately, of reduced graphene oxide sheets in a given solvent type are possible and when they are not. As an example of the utility of such colloidal suspensions, "paperlike" materials generated by very simple filtration of the reduced graphene oxide sheets had electrical conductivity values as high as 16,000 S/m.

Nano-indentation studies on polymer matrix composites reinforced by few-layer graphene

The mechanical properties of polyvinyl alcohol (PVA) and poly(methyl methacrylate) (PMMA)-matrix composites reinforced by functionalized few-layer graphene (FG) have been evaluated using the nano-indentation technique. A significant increase in both the elastic modulus and hardness is observed with the addition of 0.6 wt% of graphene. The crystallinity of PVA also increases with the addition of FG. This and the good mechanical interaction between the polymer and the FG, which provides better load transfer between the matrix and the fiber, are suggested to be responsible for the observed improvement in mechanical properties of the polymers.

Atomic and electronic structure of graphene-oxide

We elucidate the atomic and electronic structure of graphene oxide (GO) using annular dark field imaging of single and multilayer sheets and electron energy loss spectroscopy for measuring the fine structure of C and O K-edges in a scanning transmission electron microscope. Partial density of states and electronic plasma excitations are also measured for these GO sheets showing unusual pi* + sigma* excitation at 19 eV. The results of this detailed analysis reveal that the GO is rough with an average surface roughness of 0.6 nm and the structure is predominantly amorphous due to distortions from sp3 C-O bonds. Around 40% sp3 bonding was found to be present in these sheets with measured O/C ratio of 1:5. These sp2 to sp3 bond modifications due to oxidation are also supported by ab initio calculations

The mechanical properties and morphology of a graphite oxide nanoplatelet/polyurethane composite

Significant reinforcement of polyurethane (PU) using graphite oxide nanoplatelets (GONPs) is reported. Morphologic study shows that, due to the formation of chemical bonding, there is a strong interaction between the GONPs and the hard segment of the PU, which allows effective load transfer. The GONPs can prevent the formation of crystalline hard segments due to their two-dimensional structure. With the incorporation of 4.4 wt% of GONPs, the Young's modulus and hardness of the PU are significantly increased by approximately 900% and approximately 327%, respectively. The resultant high resistance to scratching indicates promise for application of these composite materials in surface coating.

Synthesis of graphene sheets with high electrical conductivity and good thermal stability by hydrogen arc discharge exfoliation

We developed a hydrogen arc discharge exfoliation method for the synthesis of graphene sheets (GSs) with excellent electrical conductivity and good thermal stability from graphite oxide (GO), in combination with solution-phase dispersion and centrifugation techniques. It was found that efficient exfoliation and considerable deoxygenation of GO, and defect elimination and healing of exfoliated graphite can be simultaneously achieved during the hydrogen arc discharge exfoliation process. The GSs obtained by hydrogen arc discharge exfoliation exhibit a high electrical conductivity of approximately 2 x 10(3) S/cm and high thermal stability with oxidization resistance temperature of 601 degrees C, which are much better than those prepared by argon arc discharge exfoliation (approximately 2 x 10(2) S/cm, 525 degrees C) and by conventional thermal exfoliation (approximately 80 S/cm, 507 degrees C) with the same starting GO. These results demonstrate that this hydrogen arc discharge exfoliation method is a good approach for the preparation of GSs with a good quality.

Graphene-based composite thin films for electronics

The electrical properties of solution-processed composite thin films consisting of functionalized graphene sheets (FGS) as the filler and polystyrene (PS) as the host material are described. We demonstrate that transistors from graphene-based composite thin films exhibit ambipolar field effect characteristics, suggesting transport via percolation among FGS in the insulating PS matrix. Device characteristics as a function of the FGS size are also reported. The results indicate that devices fabricated using the largest size FGS yield the highest mobility values. This simple and scaleable fabrication scheme based on a commodity plastic could be useful for low-cost, macro-scale electronics.

Functionalized Graphenes and Thermoplastic Nanocomposites Based upon Expanded Graphite Oxide

Exfoliation of expanded GO represents an attractive route to functionalized graphenes as versatile 2D carbon nanomaterials and components of a wide variety of polymer nanocomposites. Thermally reduced graphite oxides (TrGO) with specific surface areas of 600 to 950 m(2)  · g(-1) were obtained by oxidation of graphite followed by thermal expansion at 600 °C. Thermal post treatment at 700 °C and 1 000 °C increased carbon content (81 to 97 wt.-%) and lowered resistivity (1 600 to 50 Ω · cm). During melt extrusion with PC, iPP, SAN and PA6, exfoliation afforded uniformly dispersed graphenes with aspect ratio > 200. In comparison to conventional 0D and 1D carbon nanoparticles, TrGO afforded nanocomposites with improved stiffness and lower percolation threshold. Recent progress and new strategies in development of functionalized graphenes and graphene-based nanocomposites are highlighted.

Bending properties of single functionalized graphene sheets probed by atomic force microscopy

We probe the bending characteristics of functionalized graphene sheets with the tip of an atomic force microscope. Individual sheets are transformed from a flat into a folded configuration. Sheets can be reversibly folded and unfolded multiple times, and the folding always occurs at the same location. This observation suggests that the folding and bending behavior of the sheets is dominated by pre-existing kink (or even fault) lines consisting of defects and/or functional groups.