Synthesis methods for nanosized hydroxyapatite with diverse structures

PCL/Si-Doped Multi-Phase Calcium Phosphate Scaffolds Derived from Cuttlefish Bone

Increasing attention is focused on developing biomaterials as temporary scaffolds that provide a specific environment and microstructure for bone tissue regeneration. The aim of the present work was to synthesize silicon-doped biomimetic multi-phase composite scaffolds based on bioactive inorganic phases and biocompatible polymers (poly(ε-caprolactone), PCL) using simple and inexpensive methods. Porous multi-phase composite scaffolds from cuttlefish bone were synthesized using a hydrothermal method and were further impregnated with (3-aminopropyl)triethoxysilane 1–4 times, heat-treated (1000 °C) and coated with PCL. The effect of silicon doping and the PCL coating on the microstructure and mechanical and biological properties of the scaffolds has been investigated. Multi-phase scaffolds based on calcium phosphate (hydroxyapatite, α-tricalcium phosphate, β-tricalcium phosphate) and calcium silicate (wollastonite, larnite, dicalcium silicate) phases were obtained. Elemental mapping revealed homogeneously dispersed silicon throughout the scaffolds, whereas silicon doping increased bovine serum albumin protein adsorption. The highly porous structure of cuttlefish bone was preserved with a composite scaffold porosity of ~78%. A compressive strength of ~1.4 MPa makes the obtained composite scaffolds appropriate for non-load-bearing applications. Cytocompatibility assessment by an MTT assay of human mesenchymal stem cells revealed the non-cytotoxicity of the obtained scaffolds.

Modulatory activity of a bovine hydrolyzed collagen-hydroxyapatite food complex on human primary osteoblasts after simulating its gastrointestinal digestion and absorption

INTRODUCTION

osteoporosis is the most prevalent bone disease and one of the main causes of chronic disability in middle and advanced ages. Conventional pharmacological treatments are still limited, and their prolonged use can cause adverse effects that motivate poor adherence to treatment. Nutritional strategies are traditionally based on supplementing the diet with calcium and vitamin D. Recent studies confirm that the results of this supplementation are significantly improved if it is accompanied by the intake of oral hydrolyzed collagen.

OBJECTIVE

to evaluate the possible in vitro osteogenic activity of a peptide-mineral complex formed by bovine hydrolyzed collagen and bovine hydroxyapatite (Phoscollagen®, PHC®).

METHODS

the digestion and absorption of PHC® were simulated using the dynamic gastrointestinal digester of AINIA and Caco-2 cell model, respectively. Primary cultures of human osteoblasts were treated with the resulting fraction of PHC® and changes were evaluated in the proliferation of preosteoblasts and in the mRNA expression of osteogenic biomarkers at different stages of osteoblast maturation: Runt-related transcription factor 2 (Runx2), alkaline phosphatase (ALP), osteocalcin (OC) and type I collagen (ColA1).

RESULTS

an increase in preosteoblastic proliferation was observed (p ≤ 0,05). No changes were detected in the biomarkers of osteoblasts with 5 days of differentiation, but were with 14 days, registering an increase in Runx2 (p = 0.0008), ColA1 (p = 0.035), OC (p = 0.027) and ALP (without significance).

CONCLUSION

these results show that the PHC® peptide-mineral complex stimulates the activity of mature osteoblasts, being capable of promoting bone formation.

Light-Activated Hydroxyapatite Photocatalysts: New Environmentally-Friendly Materials to Mitigate Pollutants

This review focuses on a reasoned search for articles to treat contaminated water using hydroxyapatite (HAp)-based compounds. In addition, the fundamentals of heterogeneous photocatalysis were considered, combined with parameters that affect the pollutants’ degradation using hydroxyapatite-based photocatalyst design and strategies of this photocatalyst, and the challenges of and perspectives on the development of these materials. Many critical applications have been analyzed to degrade dyes, drugs, and pesticides using HAp-based photocatalysts. This systematic review highlights the recent state-of-the-art advances that enable new paths and good-quality preparations of HAp-derived photocatalysts for photocatalysis.

Co-doping of iron and copper ions in nanosized bioactive glass by reactive laser fragmentation in liquids

Bioactive glass (BG) is a frequently used biomaterial applicable in bone tissue engineering and known to be particularly effective when applied in nanoscopic dimensions. In this work, we employed the scalable reactive laser fragmentation in liquids method to produce nanosized 45S5 BG in the presence of light-absorbing Fe and Cu ions. Here, the function of the ions was twofold: (i) increasing the light absorption and thus causing a significant increase in laser fragmentation efficiency by a factor of 100 and (ii) doping the BG with bioactive metal ions up to 4 wt%. Our findings reveal an effective downsizing of the BG from micrometer-sized educts into nanoparticles having average diameters of <50 nm. This goes along with successful element-specific incorporation of the metal ions into the BG, inducing co-doping of Fe and Cu ions as verified by energy-dispersive X-ray spectroscopy (EDX). In this context, the overall amorphous structure is retained, as evidenced by X-ray powder diffraction (XRD). We further demonstrate that the level of doping for both elements can be adjusted by changing the BG/ion concentration ratio during laser fragmentation. Consecutive ion release experiments using inductively-coupled plasma mass spectrometry (ICP-MS) were conducted to assess the potential bioactivity of the doped nanoscopic BG samples, and cell culture experiments using MG-63 osteoblast-like cells demonstrated their cytocompatibility. The elegant method of in situ co-doping of Fe and Cu ions during BG nanosizing may provide functionality-advanced biomaterials for future studies on angiogenesis or bone regeneration, particularly as the level of doping may be adjusted by ion concentrations and ion type in solution.

(Bio)manufactured Solutions for Treatment of Bone Defects with Emphasis on US-FDA Regulatory Science Perspective

Bone defects, with second highest demand for surgeries around the globe, may lead to serious health issues and negatively influence patient lives. The advances in biomedical engineering and sciences have led to the development of several creative solutions for bone defect treatment. This review provides a brief summary of bone graft materials, an organized overview of top-down and bottom-up (bio)manufacturing approaches, plus a critical comparison between advantages and limitations of each method. We specifically discuss additive manufacturing techniques and their operation mechanisms in detail. Next, we review the hybrid methods and promising future directions for bone grafting, while giving a comprehensive US-FDA regulatory science perspective, biocompatibility concepts and assessments, and clinical considerations to translate a technology from a research laboratory to the market. The topics covered in this review could potentially fuel future research efforts in bone tissue engineering, and perhaps could also provide novel insights for other tissue engineering applications.

The Synthesis of Hydroxyapatite by Hydrothermal Process with Calcium Lactate Pentahydrate: The Effect of Reagent Concentrations, pH, Temperature, and Pressure

Hydroxyapatite and other calcium phosphates in the form of whiskers are lately widely considered as fillers for biocomposites due to their special biological and reinforcing properties. Depending on the method of synthesis, apatite whiskers of various sizes and phase composition can be obtained. In our work, hydroxyapatite (HAp) whiskers were successfully prepared in reaction between calcium lactate pentahydrate and orthophosphoric acid. The advantage of the proposed technique is the simple but precise control of the HAp crystal morphology and high product purity which is necessary for biomedical applications. The effect of reagent concentrations, pH, reaction temperature, and pressure on HAp whiskers' morphology and composition was investigated. In the result, we obtained hydroxyapatite of different morphology such as whiskers, hexagonal rods, and nanorods. The products were characterized by SEM, XRD, and FTIR. In this work, the synthesis of HAp whiskers by direct decomposition of calcium lactate pentahydrate chelates under hydrothermal conditions was showed for the first time.

Trace element adsorption from acid mine drainage and mine residues on nanometric hydroxyapatite

Mining Ag, Cu, Pb, and Zn sulfides by flotation produces great volume of residues, which oxidized through time and release acid solutions. Leachates from tailing heaps are a concern due to the risk of surface water pollution. Hydroxyapatite nanoparticles may remove trace elements from acid leachate collected from an oxidized tailing heap (pH ranged 1.69 ± 0.3 to 2.23 ± 0.16; [SO₄^2-] = 58 ± 0.67 to 60.69 ± 0.39 mmol). Based on the batch experiments under standard conditions, the average removal efficiency was 96%, 92%, 86%, and 67% for Cd, Pb, Zn, and Cu, respectively. The Zn adsorption was modeled by the Freundlich equation, but Cd, Cu, and Pb isotherms do not fit to Freundlich nor Lagmuir equations. Adsorption and other mechanisms occur during trace elements removal by hydroxyapatite. In the polymetallic system, trace elements saturate the specific surface of hydroxyapatite in the following order Zn, Cd, Cu, and Pb. The pH values must be higher than 7.5 to adsorb trace elements. The dose of 3.8% of hydroxyapatite to acid mine drainage removed efficiently > 80% of the soluble Fe, Cu, Mn, Zn, Cd, Ni, and Pb: 4020.0, 37.3, 34.8, 432.0, 4.4, 0.7, and 0.11 mg L^-1 from leachate A and 3357.1, 46.6, 27.8, 569.0, 4.7, 0.6, and 1.7 from leachate B, respectively. The application of 0.7% of hydroxyapatite decreased the extractable Pb in unoxidized tailing heaps from 272 to 100 mg kg^-1. It is likely to use hydroxyapatite to control trace element mobility from mine residues to surrounding soils and surface water.

Anhydrous calcium phosphate crystals stabilize DNA for dry storage

The resilience of ancient DNA (aDNA) in bone gives rise to the preservation of synthetic DNA with bioinorganic materials such as calcium phosphate (CaP). Accelerated aging experiments at elevated temperature and humidity displayed a positive effect of co-precipitated, crystalline dicalcium phosphate on the stability of synthetic DNA in contrast to amorphous CaP. Quantitative PXRD in combination with SEM and EDX measurements revealed distinct CaP phase transformations of calcium phosphate dihydrate (brushite) to anhydrous dicalcium phosphate (monetite) influencing DNA stability.

Advances of Hydroxyapatite Hybrid Organic Composite Used as Drug or Protein Carriers for Biomedical Applications: A Review

Hydroxyapatite (HA), especially in the form of HA nanoparticles (HANPs), has excellent bioactivity, biodegradability, and osteoconductivity and therefore has been widely used as a template or additives for drug delivery in clinical applications, such as dentistry and orthopedic repair. Due to the atomically anisotropic distribution on the preferred growth of HA crystals, especially the nanoscale rod-/whisker-like morphology, HA can generally be a good candidate for carrying a variety of substances. HA is biocompatible and suitable for medical applications, but most drugs carried by HANPs have an initial burst release. In the adsorption mechanism of HA as a carrier, specific surface area, pore size, and porosity are important factors that mainly affect the adsorption and release amounts. At present, many studies have developed HA as a drug carrier with targeted effect, porous structure, and high porosity. This review mainly discusses the influence of HA structures as a carrier on the adsorption and release of active molecules. It then focuses on the benefits and effects of different types of polymer-HA composites to re-examine the proteins/drugs carry and release behavior and related potential clinical applications. This literature survey can be divided into three main parts: 1. interaction and adsorption mechanism of HA and drugs; 2. advantages and application fields of HA/organic composites; 3. loading and drug release behavior of multifunctional HA composites in different environments. This work also presents the latest development and future prospects of HA as a drug carrier.

Stimulation of Metabolic Activity and Cell Differentiation in Osteoblastic and Human Mesenchymal Stem Cells by a Nanohydroxyapatite Paste Bone Graft Substitute

Advances in nanotechnology have been exploited to develop new biomaterials including nanocrystalline hydroxyapatite (nHA) with physical properties close to those of natural bone mineral. While clinical data are encouraging, relatively little is understood regarding bone cells’ interactions with synthetic graft substitutes based on this technology. The aim of this research was therefore to investigate the in vitro response of both osteoblast cell lines and primary osteoblasts to an nHA paste. Cellular metabolic activity was assessed using the cell viability reagent PrestoBlue and quantitative, real-time PCR was used to determine gene expression related to osteogenic differentiation. A potential role of calcium-sensing receptor (CaSR) in the response of osteoblastic cells to nHA was also investigated. Indirect contact of the nHA paste with human osteoblastic cells (Saos-2, MG63, primary osteoblasts) and human bone marrow-derived mesenchymal stem cells enhanced the cell metabolic activity. The nHA paste also stimulated gene expression of runt-related transcription factor 2, collagen 1, alkaline phosphatase, and osteocalcin, thereby indicating an osteogenic response. CaSR was not involved in nHA paste-induced increases in cellular metabolic activity. This investigation demonstrated that the nHA paste has osteogenic properties that contribute to clinical efficacy when employed as an injectable bone graft substitute.

Solvothermal Synthesis of Calcium-Deficient Hydroxyapatite via Hydrolysis of α-Tricalcium Phosphate in Different Aqueous-Organic Media

In the present work, the effects of various organic solvents (solvent nature and fraction within the solution) and solvothermal conditions on the formation of calcium-deficient hydroxyapatite (CDHA) via hydrolysis of α-tricalcium phosphate (α-TCP) are investigated. The wet precipitation method is applied for α-TCP synthesis, and the hydrolysis reaction is performed in solutions with different water-to-organic solvent ratios under solvothermal conditions at 120 °C for 3 h and at 200 °C for 5 h. Ethyl alcohol, isopropyl alcohol, and butyl alcohol did not inhibit the hydrolysis of α-TCP, while methyl alcohol and ethylene glycol have a more prominent inhibitory effect on the hydrolysis, hence the formation of single-phased CDHA. From all the solvents analysed, ethylene glycol has the highest impact on the sample morphology. Under certain water to ethylene glycol ratios and solvothermal conditions, samples containing a significant fraction of rods are obtained. However, samples prepared with ethylene glycol are characterised by a particularly low BET surface area.

Hydroxyapatite-based adsorbents: Applications in sequestering heavy metals and dyes

Hydroxyapatite (HAp) is a calcium phosphate material that was used primarily in bone regeneration and repair as a result of its chemical similarity with bone. However, HAp has emerged as a very promising adsorbent for sequestering contaminants like heavy metals, dyes, hydrocarbons as well as other emerging pollutants from wastewater as a result of its versatility and encouraging adsorptive properties. Contaminants like heavy metals and dyes have been a major source of environmental concern. Research studies involving the use of HAp as adsorbents for the adsorptive treatment of heavy metal- and dye-contaminated wastewater have become increasingly popular due to its eco-friendliness, easy synthesis, unique adsorption properties etc. Various methods are available for the synthesis of HAp and its composites with some of these methods used in combination with other methods to obtain more efficient HAp-based adsorbents. In this work, the adsorptive removal of heavy metals and dyes by HAp and its composites was extensively reviewed as well as the parametric effects of process factors like contact time, solution pH, temperature, solute concentration etc on the adsorption process. Kinetic, thermodynamic, and isotherm models for elucidating the adsorption process were also considered. Generally, from the works reviewed, HAp-based adsorbents were found to be very effective for sequestering heavy metals and dyes from solution and thus presents a low-cost option for adsorptive wastewater treatment.

Prevention of Caries and Dental Erosion by Fluorides-A Critical Discussion Based on Physico-Chemical Data and Principles

Dental erosion is a common problem in dentistry. It is defined as the loss of tooth mineral by the attack of acids that do not result from caries. From a physico-chemical point of view, the nature of the corroding acids only plays a minor role. A protective effect of fluorides, to prevent caries and dental erosion, is frequently claimed in the literature. The proposed modes of action of fluorides include, for example, the formation of an acid-resistant fluoride-rich surface layer and a fluoride-induced surface hardening of the tooth surface. We performed a comprehensive literature study on the available data on the interaction between fluoride and tooth surfaces (e.g., by toothpastes or mouthwashes). These data are discussed in the light of general chemical considerations on fluoride incorporation and the acid solubility of teeth. The analytical techniques available to address this question are presented and discussed with respect to their capabilities. In summary, the amount of fluoride that is incorporated into teeth is very low (a few µg mm-2), and is unlikely to protect a tooth against an attack by acids, be it from acidic agents (erosion) or from acid-producing cariogenic bacteria.

Surface functionalization of natural hydroxyapatite by polymerization of β-cyclodextrin: application as electrode material for the electrochemical detection of Pb(II)

A composite material prepared by polymerization of β-cyclodextrin (β-CD) on the surface of natural hydroxyapatite using citric acid as cross linker, was employed as electrode material for the detection of Pb(II). Hydroxyapatite was obtained from bovine bones, following a three-step procedure including pre-calcination, chemical treatment with (NH₄)₂HPO_4, and calcination. The structure and morphology of the pristine hydroxyapatite (NHAP_P0.5) and its functionalized counterpart (NHAP_p0.5-CA-β-CD) were examined using XRD, FTIR, and SEM. Upon deposition as thin film on a glassy carbon electrode (GCE), the ion exchange ability of NHAP_p0.5-CA-β-CD was exploited to elaborate a sensitive sensor for the detection of lead. The electroanalytical procedure was based on the chemical accumulation of Pb(II) ions under open-circuit conditions, followed by the detection of the preconcentrated species using differential pulse anodic stripping voltammetry. The reproducibility of the proposed method, based on a series of 8 measurements in a solution containing 2 μM Pb(II) gave a coefficient of variation of 1.27%. Significant parameters that can affect the stripping response of Pb(II) were optimized, leading to a linear calibration curve for lead in the concentration range of 2 × 10^-8 mol L^-1 - 20 × 10^-8 mol L^-1 (R² = 0.998). The detection limit (3S/m) and the sensitivity of the proposed sensor were 5.06 × 10^-10 mol L^-1 and 100.80 μA.μM^-1, respectively. The interfering effect of several ions expected to affect the determination of lead was evaluated, and the proposed sensor was successfully applied in the determination of Pb(II) ions in spring water, well water, river water and tap water samples.

Treatment of Traumatic Cartilage Defects of Rabbit Knee Joint by Adipose Derived Stem Cells Combined with Kartogenin Hydroxyapatite Nano-Microsphere Complex

Kartogenin (KGN) can effectively promote the differentiation of adipose derived stem cells (ADSCs) into chondrocytes. With the help of three-dimensional slow-release technology, nano-microspheres are generated and used for cartilage repair. First, KGN solution was prepared, which was dissolved in distilled water, and NaOH solution, HEPES buffer, sodium chloride particles, and hydroxyapatite (HA) solution were added to prepare KGN-HA gel solution containing KGN. ADSCs were isolated from the posterior iliac of four-week-old New Zealand rabbits. After 0.5 mL of rabbit second-generation ADSCs suspension was taken, 2 mL KGN-HA gel solution was added, and they were mixed well to obtain ADSCs/KGN-HA gel. After drying treatment, ADSCs/KGN-HA nanospheres were precipitated. In the experiment, the minimum inhibitory concentration (MIC) of Staphylococcus aureus (MIC) > 2 μg/mL in each group of KGN-HA gel solution was reached within 30 days. Group K3 had the highest KGN encapsulation rate and the largest cumulative release. The biological activity of ADSCs was good in the ADSCs/KGN-HA nanoparticle solution. After two weeks of incubation, the nanospheres were positive for type II collagen staining/toluidine blue staining, that was, chondrocyte phenotype. The rabbit knee articular cartilage defect model was established. The defect part was filled with ADSCs/KGN-HA gel, which was similar in color to the surrounding tissues. The two sides of the tissue section and the surrounding cartilage tissue healed well, and no carrier material remained. Moreover, the cells were round, with cartilage lacuna formed around them, and after the simple periosteum was covered and repaired, the surface was sunken. The cell structure changed, and the healing with the surroundings was poor. In summary, under the slow release of KGN, ADSCs/KGN-HA nanospheres made ADSCs maintain a good biological form, which grew and proliferated normally. The ADSCs/KGN-HA nanoparticles cultured in vitro had a good repair effect on the animal model of articular cartilage defects.

Hydroxyapatite as a bifunctional nanocatalyst for solventless Henry reaction: a demonstration of morphology-dependent catalysis

Hydroxyapatite nanorods are catalytically active while nanoplates are inactive towards Henry reaction due to the differences in the exposed surfaces.

Nanosized calcium deficient hydroxyapatites for tooth enamel protection

Calcium phosphates (CaP) are extensively studied as additives to dental care products for tooth enamel protection against caries. However, it is not clear yet whether substituted CaP could provide better enamel protection. In this study we produced, characterized and tested in vitro substituted and co‐substituted calcium deficient hydroxyapatite (CDHAp) with Sr²⁺ and F⁻ ions. X‐ray powder diffractometry, Fourier transformation infrared spectroscopy, scanning electron microscopy, energy‐dispersive X‐ray analysis, Brunauer–Emmett–Teller were used to characterize synthesized powders and also cytotoxicity was evaluated. pH = f(t) test was performed to estimate, weather synthesized CDHAp suspensions are able to increase pH of experimental media after acid addition. Synthesis products were incorporated into paste to perform in vitro remineralization on the bovine enamel. In addition to mentioned instrumental methods, profilometry was used for evaluation of remineralised enamel samples. The obtained results confirmed formation of CDHAp substituted with 1.5–1.6 wt% of fluoride and 7.4–7.8 wt% of strontium. pH = f(t) experiment pointed out that pH increased by approximately 0.3 within 10 min after acid addition for all CDHAp suspensions. A new layer of the corresponding CDHAp was formed on the enamel. Its thickness increased by 0.8 ± 0.1 μm per day and reached up to 5.8 μm after 7 days. Additionally, octa calcium phosphates were detected on the surface of control samples. In conclusion, we can assume that CDHAp substituted with Sr²⁺ and/or F⁻ could be used as an effective additive to dental care products promoting formation of protecting layer on the enamel, but there was no significant difference among sample groups.

A Narrative Review of u-HA/PLLA, a Bioactive Resorbable Reconstruction Material: Applications in Oral and Maxillofacial Surgery

The advent of bioresorbable materials to overcome limitations and replace traditional bone-reconstruction titanium-plate systems for bone fixation, thus achieving greater efficiency and safety in medical and dental applications, has ushered in a new era in biomaterial development. Because of its bioactive osteoconductive ability and biocompatibility, the forged composite of uncalcined/unsintered hydroxyapatite and poly L-lactic acid (u-HA/PLLA) has attracted considerable interest from researchers in bone tissue engineering, as well as from clinicians, particularly for applications in maxillofacial reconstructive surgery. Thus, various in vitro studies, in vivo studies, and clinical trials have been conducted to investigate the feasibility and weaknesses of this biomaterial in oral and maxillofacial surgery. Various technical improvements have been proposed to optimize its advantages and limit its disadvantages. This narrative review presents an up-to-date, comprehensive review of u-HA/PLLA, a bioactive osteoconductive and bioresorbable bone-reconstruction and -fixation material, in the context of oral and maxillofacial surgery, notably maxillofacial trauma, orthognathic surgery, and maxillofacial reconstruction. It simultaneously introduces new trends in the development of bioresorbable materials that could used in this field. Various studies have shown the superiority of u-HA/PLLA, a third-generation bioresorbable biomaterial with high mechanical strength, biocompatibility, and bioactive osteoconductivity, compared to other bioresorbable materials. Future developments may focus on controlling its bioactivity and biodegradation rate and enhancing its mechanical strength.

Effectiveness of a Nanohydroxyapatite-Based Hydrogel on Alveolar Bone Regeneration in Post-Extraction Sockets of Dogs with Naturally Occurring Periodontitis

Pathological mandibular fracture after dental extraction usually occurs in dogs with moderate to severe periodontitis. A nanohydroxyapatite-based hydrogel (HAP hydrogel) was developed to diminish the limitations of hydroxyapatite for post-extraction socket preservation (PSP). However, the effect of the HAP hydrogel in dogs has still not been widely investigated. Moreover, there are few studies on PSP in dogs suffering from clinical periodontitis. The purpose of this study was to evaluate the effectiveness of the HAP hydrogel for PSP in dogs with periodontitis. In five dogs with periodontitis, the first molar (309 and 409) of each hemimandible was extracted. Consequently, all the ten sockets were filled with HAP-hydrogel. Intraoral radiography was performed on the day of operation and 2, 4, 8 and 12 weeks post operation. The Kruskal-Wallis test and paired t-test were adopted for alveolar bone regeneration analysis. The results demonstrated that the radiographic grading, bone height measurement, and bone regeneration analysis were positively significant at all follow-up times compared to the day of operation. Moreover, the scanning electron microscopy with energy-dispersive X-ray spectroscopy imaging after immersion showed a homogeneous distribution of apatite formation on the hydrogel surface. Our investigation suggested that the HAP hydrogel effectively enhances socket regeneration in dogs with periodontitis and can be applied as a bone substitute for PSP in veterinary dentistry.

Self-Organized Spatiotemporal Mineralization of Hydrogel: A Simulant of Osteon

Nature creates fascinating self-organized spatiotemporal patterns through the delicate control of reaction-diffusion dynamics. As the primary unit of cortical bone, osteon has concentric lamellar architecture, which plays a crucial role in the mechanical and physiological functions of bone. However, it remains a great challenge to fabricate the osteon-like structure in a natural self-organization way. Taking advantage of the nonequilibrium reaction in hydrogels, a simple mineralization strategy to closely mimic the formation of osteon in a mild physiological condition is developed. By constructing two reverse concentration gradients of ions from periphery to interior of cylindrical hydrogel, spatiotemporal self-organization of calcium phosphate in concentric rings is generated. It is noteworthy that minerals in different layers possess diverse contents and crystalline phases, which further guide the adhesion and spread of osteoblasts on these patterns, resembling the architecture and cytological behavior of osteon. Besides, theoretical data indicates the predominate role of ion concentrations and pH values of solution, in good accordance with experimental results. Independent of precise instruments, this lifelike method is easily obtained, cost-efficient, and effectively imitates the mineral deposition in osteon from a physiochemical view. The strategy may be expanded to develop other functional material patterns via spatiotemporal self-organization.

Effect of Doping Element and Electrolyte’s pH on the Properties of Hydroxyapatite Coatings Obtained by Pulsed Galvanostatic Technique

Hydroxyapatite (HAp) is the most widely used calcium phosphate as a coating on metal implants due to its biocompatibility and bioactivity. The aim of this research is to evaluate the effect of the pH’s electrolyte and doping element on the morphology, roughness, chemical, and phasic composition of hydroxyapatite-based coatings obtained by pulsed galvanostatic electrochemical deposition. As doping elements, both Sr and Ag were selected due to their good osseoinductive character and antibacterial effect, respectively. The electrolytes were prepared at pH 4 and 5, in which specific concentrations of Sr, Ag, and Sr + Ag were added. In terms of morphology, all coatings consist in ribbon-like crystals, which at pH 5 appear to be a little larger. Addition of Sr did not affect the morphology of HAp, while Ag addition has led to the formation of flower-like crystals agglomeration. When both doping elements were added, the flowers like agglomerations caused by the Ag have diminished, indicating the competition between Sr and Ag. X-Ray Diffraction analysis has highlighted that Sr and/or Ag have successfully substituted the Ca in the HAp structure. Moreover, at higher pH, the crystallinity of all HAp coatings was enhanced. Thus, it can be said that the electrolyte’s pH enhances to some extent the properties of HAp-based coatings, while the addition of Sr and/or Ag does not negatively impact the obtained features of HAp, indicating that by using pulsed galvanostatic electrochemical deposition, materials with tunable features dictated by the function of the coated medical device can be designed.

Effect of Hydroxyapatite Microspheres, Amoxicillin-Hydroxyapatite and Collagen-Hydroxyapatite Composites on Human Dental Pulp-Derived Mesenchymal Stem Cells

In this study, the preparation and characterization of three hydroxyapatite-based bioactive scaffolds, including hydroxyapatite microspheres (HAps), amoxicillin–hydroxyapatite composite (Amx–HAp), and collagen–hydroxyapatite composite (Col–HAp) were performed. In addition, their behavior in human dental pulp mesenchymal stem cell (hDPSC) culture was investigated. HAps were synthesized through the following methods: microwave hydrothermal, hydrothermal reactor, and precipitation, respectively. hDPSCs were obtained from samples of third molars and characterized by immunophenotypic analysis. Cells were cultured on scaffolds with osteogenic differentiation medium and maintained for 21 days. Cytotoxicity analysis and migration assay of hDPSCs were evaluated. After 21 days of induction, no differences in genes expression were observed. hDPSCs highly expressed the collagen IA and the osteonectin at the mRNA. The cytotoxicity assay using hDPSCs demonstrated that the Col–HAp group presented non-viable cells statistically lower than the control group (p = 0.03). In the migration assay, after 24 h HAps revealed the same migration behavior for hDPSCs observed compared to the positive control. Col–HAp also provided a statistically significant higher migration of hDPSCs than HAps (p = 0.02). Migration results after 48 h for HAps was intermediate from those achieved by the control groups. There was no statistical difference between the positive control and Col–HAp. Specifically, this study demonstrated that hydroxyapatite-based bioactive scaffolds, especially Col-Hap, enhanced the dynamic parameters of cell viability and cell migration capacities for hDPSCs, resulting in suitable adhesion, proliferation, and differentiation of this osteogenic lineage. These data presented are of high clinical importance and hold promise for application in therapeutic areas, because Col–HAp can be used in ridge preservation, minor bone augmentation, and periodontal regeneration. The development of novel hydroxyapatite-based bioactive scaffolds with clinical safety for bone formation from hDPSCs is an important yet challenging task both in biomaterials and cell biology.

Mechanical Properties of Differently Nanostructured and High-Pressure Compressed Hydroxyapatite-Based Materials for Bone Tissue Regeneration

Hydroxyapatite (HAp) has long been considered the gold standard in the biomedical field, considering its composition and close resemblance to human bone. However, the brittle nature of hydroxyapatite (HAp) biomaterial, constrained by its low fracture toughness (of up to 1.2 vs. 2–12 MPa m1/2 of human bone), remains one of the significant factors impairing its use in bone regeneration. In the present study, HAp nanoparticles synthesized by the solid-state (SHAp) and sonochemical (EHAp) approaches using eggshell-derived calcium hydroxide and ammonium dihydrogen orthophosphate as precursors are compared with those synthesized using commercially available calcium hydroxide and ammonium dihydrogen orthophosphate as precursors (CHAp) employing sonochemical method. The HAp samples were then compressed into compact materials using a uniaxial high-pressure compression technique at a preoptimized load and subsequently characterized for mechanical properties using the Vickers indentation method and compressive strength testing. The analysis revealed that the material with smaller particle size (30–40 nm) and crystalline nature (EHAp and CHAp) resulted in mechanically robust materials (σm = 54.53 MPa and 47.72 MPa) with high elastic modulus (E = 4011.1 MPa and 2750.25 MPa) and density/hardness-dependent fracture toughness (σf = 4.34 MPa m1/2and 6.57 MPa m1/2) than SHAp (σm =28.40 MPa, E = 2116.75 MPa, σf = 5.39 MPa m1/2). The CHAp material was found to be the most suitable for applications in bone regeneration.

An update on hydroxyapatite/collagen composites: What is there left to say about these bioinspired materials?

Hydroxyapatite (HAp)/collagen-based composite materials have been a constant in the development of bioinspired materials for bone tissue engineering. The most fundamental research works focus on combining HAp, due to its chemical similarity with the mineral component of bones, and collagen, which is the most abundant protein in the body. Modern studies have explored different two-dimensional (2D) and 3D structures, in order to obtain biomaterials with specific physicochemical, mechanical, and biological characteristics that can be applied in distinct biomedical applications. However, as there is already so much work developed with these materials, it is crucial to question: what can still be done? What is the importance of current know-how for the future of bioinspired materials? In this paper we intend to review and update the available methodologies to synthesize HAp/collagen composites, along with their characteristics. In addition, the future of these materials in terms of applications and their potential as a cutting-edge technology is discussed.

A Study of Thermal Stability of Hydroxyapatite

High-temperature powder sintering is an integral part of the dense ceramic manufacturing process. In order to find the optimal conditions for producing a ceramic product, the information about its behavior at high temperatures is required. However, the data available in the literature are very contradictory. In this work, the thermal stability of hydroxyapatite prepared by a solid-state mechanochemical method and structural changes occurring during sintering were studied. Stoichiometric hydroxyapatite was found to remain as a single-phase apatite structure with the space group P63/m up to 1300 °C inclusively. A further increase in the sintering temperature leads to its partial decomposition, a decrease in the crystallite size of the apatite phase, and the appearance of significant structural strains. It was shown that small deviations from stoichiometry in the Ca/P ratio upward or downward during the hydroxyapatite synthesis lead to a significant decrease in the thermal stability of hydroxyapatite. An apatite containing almost no hydroxyl groups, which is close to the composition of oxyapatite, was prepared. It was shown that the congruent melting of stoichiometric hydroxyapatite upon slow heating in a high-temperature furnace does not occur. At the same time, the fast heating of hydroxyapatite by laser radiation allows, under certain conditions, its congruent melting with the formation of a recrystallized monolayer of oxyhydroxyapatite. The data obtained in this study can be used when choosing sintering conditions to produce hydroxyapatite-based ceramics.

Biomimetic Mechanically Strong One-Dimensional Hydroxyapatite/Poly(d,l-lactide) Composite Inducing Formation of Anisotropic Collagen Matrix

Natural bone is a complex composite, consisting predominantly of collagen and hydroxyapatite (HA), which form a highly organized, hierarchical structure from the nano- to the macroscale. Because of its biphasic, anisotropic, ultrafine structural design, bone tissue possesses excellent mechanical properties. Herein, inspired by the composition and microstructure of natural bone, a biphasic composite consisting of highly aligned strontium/copper-doped one-dimensional hydroxyapatite (Sr/Cu-doped 1D HA) and poly(d,l-lactide) (PDLA) was developed. The presence and alignment of Sr/Cu-doped 1D HA crystals resulted in mechanical reinforcement of the polymer matrix, including compressive and tensile strength and modulus, fracture toughness, swelling resistance, and long-term structural stability. The compressive strength, tensile strength, and Young's modulus of the biomimetic composite were comparable to that of cortical bone. Biologically, the biomimetic composite showed a sustained release of the incorporated Sr and Cu ions, facilitated mineral deposition from simulated body fluid, and supported attachment, proliferation, and alkaline phosphatase activity of human mesenchymal stromal cells (hMSCs). Moreover, the highly aligned Sr/Cu-doped 1D HA crystals in the 3D porous scaffolds induced the alignment of hMSCs and secretion of an anisotropic collagen fiber matrix in 3D. The biomimetic Sr/Cu-doped 1D HA/PDLA composite presented here contributes to the current efforts aiming at the design and development of load-bearing bioactive synthetic bone graft substitutes. Moreover, the biomimetic composite may serve as a 3D platform for studying cell-extracellular matrix interactions in bone tissue.

Nano-Hydroxyapatite Gel and Its Effects on Remineralization of Artificial Carious Lesions

Introduction

Nano-hydroxyapatite gel (NHG) has never been investigated for enamel remineralization. This study evaluated the effects of two concentrations of NHG on remineralization of an artificial carious lesion in comparison with nano-HA toothpaste (NHT) and fluoride varnish (FV).

Materials and Methods

Carious lesions were prepared on 100 enamel samples and divided into 5 groups: FV, NHT, 20% NHG, and 30% NHG. One untreated (NT) group was left as control. The hardness of the surface was evaluated before, during, and after remineralization. Microhardness at various phases and the percent recovery of hardness (%HR) were determined and analyzed with ANOVA. Polarized-light micrographs (PLM) were evaluated for depth of the carious lesion.

Results

Significantly different remineralization capability was indicated for tested agents (p < 0.05). NHT was significantly capable of remineralization greater than NHG, FV, and NT (p < 0.05). No noticeable difference in %HR between 20% NHG and 30% NHG (p > 0.05) was found. Decreasing in the depth of caries lesion was notified by PLM as applying either NHT or NHG as greater than FV, with no reduction in the depth for NT.

Conclusions

Nano-HA both in toothpaste and gel form was capable of remineralization better than fluoride varnish. Comparable remineralization of 20% versus 30% NHG was evidenced. NHG for both concentrations was recommended as a capable remineralizing agent for caries remineralization. Clinical Significance: This study indicated that an application of nano-HA gel is an attractive route to deliver the material and can be more effective and less toxic than conventional formulations and provide its effectiveness directly at the site of action, especially for a noncooperative young child and medicinally intimidated patients who may face with inconvenience in using toothbrush and toothpaste for hygiene control.

Solid-State NMR and Raman Spectroscopic Investigation of Fluoride-Substituted Apatites Obtained in Various Thermal Conditions

Fluoride-substituted apatites were synthesized by the standard sol-gel method and then calcined at three different temperatures: 800 °C, 1000 °C, and 1200 °C. Using a similar method, hydroxyapatite was synthesized and used as a reference material. The obtained powders were characterized by physicochemical methods: powder X-ray diffractometry, Raman spectroscopy, transmission electron microscopy, and solid-state nuclear magnetic resonance. All these methods allowed to identify additional α-TCP phase (tricalcium phosphate) in the HAP samples heated at 1000 °C and 1200 °C while fluoridated apatites turned out to be thermally stable. Moreover, Raman spectroscopy and NMR allowed to establish that the powders substituted with fluoride ions are not pure fluorapatite and contain OH- groups in the crystal structure. All the obtained materials had crystals with a shape similar to that of biological apatite.

Development of a novel direct dental pulp-capping material using 4-META/MMA-TBB resin with nano hydroxyapatite

In the case of dental pulp exposure, direct pulp capping is often performed to preserve vital dental pulp tissue. Numerous studies regarding the development of direct pulp-capping materials have been conducted, but materials with an appropriate sealing ability, which induce dense reparative dentin formation, have not been developed. Although nano hydroxyapatite (naHAp) is a bone-filling material with bioactivity and biocompatibility, the inductive effects of naHAp on reparative dentin formation remain unclear. In the present study, the effects of dental adhesive material 4-methacryloxyethyl trimellitate anhydride/methyl methacrylate tri-n-butylborane [4-META/MMA-TBB or Super-bond (SB)], which included 10%, 30%, and 50% naHAp (naHAp/SB) on odontoblastic differentiation of dental pulp stem cells (DPSCs) and reparative dentin formation were investigated. Scanning electron microscopy (SEM) and energy dispersive X-ray spectrometer analysis were performed to verify the existence of naHAp particles on the surface of naHAp/SB discs. The tensile adhesive strength of naHAp/SB was measured using a universal testing machine. As a result, 10% naHAp/SB and 30% naHAp/SB showed almost the same tensile adhesive strength as SB but 50% naHAp/SB showed significantly lower than the other experimental group. WST-1 proliferation assay and SEM analysis revealed that naHAp/SB did not affect the proliferation of DPSCs. Calcium release assay, quantitative RT-PCR, and western blotting analysis demonstrated that naHAp/SB did not release calcium ion but 30% naHAp/SB increased the expression of calcium-sensing receptor (CaSR) in DPSCs. Additionally, quantitative RT-PCR, western blotting analysis, Alizarin Red S- and von Kossa staining revealed that 30% naHAp/SB induced odontoblastic differentiation of DPSCs, which was inhibited by a MEK/ERK inhibitor and CaSR antagonist. Furthermore, 30% naHAp/SB promoted dense reparative dentin formation in an experimentally-formed rat dental pulp exposure model. These findings suggest that 30% naHAp/SB can be used as an ideal direct pulp capping material.

The Use of Calcium Phosphates in Cosmetics, State of the Art and Future Perspectives

Calcium phosphates (CaPs) belong to a class of biomimetic materials widely employed for medical applications thanks to their excellent properties, such as biodegradability, biocompatibility and osteoinductivity. The recent trend in the cosmetics field of substituting potentially hazardous materials with natural, safe, and sustainable ingredients for the health of consumers and for the environment, as well as the progress in the materials science of academics and chemical industries, has opened new perspectives in the use of CaPs in this field. While several reviews have been focused on the applications of CaP-based materials in medicine, this is the first attempt to catalogue the properties and use of CaPs in cosmetics. In this review a brief introduction on the chemical and physical characteristics of the main CaP phases is given, followed by an up-to-date report of their use in cosmetics through a large literature survey of research papers and patents. The application of CaPs as agents in oral care, skin care, hair care, and odor control has been selected and extensively discussed, highlighting the correlation between the chemical, physical and toxicological properties of the materials with their final applications. Finally, perspectives on the main challenges that should be addressed by the scientific community and cosmetics companies to widen the application of CaPs in cosmetics are given.

Marine-Derived Biowaste Conversion into Bioceramic Membrane Materials: Contrasting of Hydroxyapatite Synthesis Methods

Marine-derived biowaste increment is enormous, yet could be converted into valuable biomaterial, e.g., hydroxyapatite-based bioceramic. Bioceramic material possesses superiority in terms of thermal, chemical, and mechanical properties. Bioceramic material also has a high level of biocompatibility when projected into biological tissues. Tuning the porosity of bioceramic material could also provide benefits for bioseparation application, i.e., ultrafiltration ceramic membrane filtration for food and dairy separation processes. This work presents the investigation of hydroxyapatite conversion from crab-shells marine-based biowaste, by comparing three different methods, i.e., microwave, coprecipitation, and sol-gel. The dried crab-shells were milled and calcinated as calcium precursor, then synthesized into hydroxyapatite with the addition of phosphates precursors via microwave, coprecipitation, or sol-gel. The compound and elemental analysis, degree of crystallinity, and particle shape were compared. The chemical compounds and elements from three different methods were similar, yet the degree of crystallinity was different. Higher Ca/P ratio offer benefit in producing a bioceramic ultrafiltration membrane, due to low sintering temperature. The hydroxyapatite from coprecipitation and sol-gel methods showed a significant degree of crystallinity compared with that of the microwave route. However, due to the presence of Fe and Sr impurities, the secondary phase of Ca9FeH(PO4)7 was found in the sol-gel method. The secondary phase compound has high absorbance capacity, an advantage for bioceramic ultrafiltration membranes. Furthermore, the sol-gel method could produce a snake-like shape, compared to the oval shape of the coprecipitation route, another benefit to fabricate porous bioceramic for a membrane filter.

Role of Nanoscale Hydroxyapatite in Disease Suppression of Fusarium-Infected Tomato

The present study investigated the mechanisms by which large- and small-sized nanoscale hydroxyapatite (nHA) suppressed Fusarium-induced wilt disease in tomato. Both nHA sizes at 9.3 mg/L (low) and 46.5 mg/L (high dose) phosphorus (P) were foliar-sprayed on Fusarium-infected tomato leaf surfaces three times. Diseased shoot mass was increased by 40% upon exposure to the low dose of large-sized nHA compared to disease controls. Exposure to both nHA sizes significantly elevated phenylalanine ammonialyase activity and total phenolic content in Fusarium-infected shoots by 30-80% and 40-68%, respectively. Shoot salicylic acid content was also increased by 10-45%, suggesting the potential relationship between antioxidant and phytohormone pathways in nHA-promoted defense against fungal infection. Exposure to the high dose of both nHA sizes increased the root P content by 27-46%. A constrained analysis of principal coordinates suggests that high dose of both nHA sizes significantly altered the fatty acid profile in diseased tomato. Particularly, the diseased root C18:3 content was increased by 28-31% in the large-sized nHA treatments, indicating that nHA remodeled the cell membrane as part of defense against Fusarium infection. Taken together, our findings demonstrate the important role of nHA in promoting disease suppression for the sustainable use of nHA in nanoenabled agriculture.

Eggshell derived nano-hydroxyapatite incorporated carboxymethyl chitosan scaffold for dentine regeneration: A laboratory investigation

AIM

To assess odontogenic differentiation abilities of porous biomineralizable composite scaffolds comprising eggshell derived nano-hydroxyapatite (HAnp) and carboxymethyl chitosan (CMC) on cultured human dental pulp stem cells (hDPSCs).

METHODOLOGY

Nano-hydroxyapatite was derived from eggshells using a simple combustion method and CMC was prepared from chitosan through a chemical route. Several compositions of HAnp-CMC (0:5, 5:0, 1:5, 2:5, 3:5, 4:5 and 1:1 w/w%) scaffolds were prepared by magnetic stirring and freeze-drying methods. HAnp-CMC scaffolds were characterized using high-resolution scanning electron microscopy combined with energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy and X-ray diffraction methods. In vitro bioactivity was determined following the interaction in simulated body fluid for 21 days. The optimized composite was then loaded onto hDPSCs to assess cell viability/proliferation, dentine sialophosphoprotein (DSPP) and vascular endothelial growth factor (VEGF) expressions using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide assay, real-time quantitative polymerase chain reaction and flow cytometry methods, respectively, following 7, 14 and 21 days. For intergroup and intragroup comparisons, Kruskal-Wallis and Friedman tests were employed, respectively, followed by appropriate post hoc test (Dunn). Significant levels were set at *p < .05 and *p < .01.

RESULTS

Synthesized hydroxyapatite (HAp) comprised crystals ranging from 20 to 50 nm (HAnp) with spherulite morphology and calcium/phosphorus (Ca/P) molar ratio of 1.67. The ultrastructure of all the scaffolds revealed a highly interconnected porous microstructure, whilst the chemical characterization displayed specific functional groups of both HAnp and CMC. In vitro bioactivity assessment confirmed the biomineralization potential of all scaffolds with an apatite-like crystal formation on the surface. The 1:5 HAnp-CMC revealed a favourable pore size (60-180 µm) that was suitable for cell seeding and was chosen for further experiments. Cell viability/proliferation rates of hDPSCs loaded 1:5 HAnp-CMC at 21st day was significantly greater than that at 7th day (p < .05). The mean relative quantification of DSPP expression by the scaffold was significantly higher (p < .05) on day 21 (3.16) than on day 7 (1.67). Mean fluorescence intensity of the VEGF expression at day 21 (32.5) was also significantly higher (p < .01) than at day 7 (12.54).

CONCLUSION

hDPSCs on 1:5 HAnp-CMC scaffolds displayed increased cell viability/proliferation and enhanced DSPP as well as VEGF expressions. The 1:5 HAnp-CMC composite has the potential to serve as a promising scaffold for dentine regeneration.

Nano-Hydroxyapatite as a Delivery System for Promoting Bone Regeneration In Vivo: A Systematic Review

Nano-hydroxyapatite (nHA) has been widely used as an orthopedic biomaterial and vehicle for drug delivery owing to its chemical and structural similarity to bone minerals. Several studies have demonstrated that nHA based biomaterials have a potential effect for bone regeneration with very minimal to no toxicity or inflammatory response. This systematic review aims to provide an appraisal of the effectiveness of nHA as a delivery system for bone regeneration and whether the conjugation of proteins, antibiotics, or other bioactive molecules to the nHA further enhances osteogenesis in vivo. Out of 282 articles obtained from the literature search, only 14 articles met the inclusion criteria for this review. These studies showed that nHA was able to induce bone regeneration in various animal models with large or critical-sized bone defects, open fracture, or methicillin-resistant Staphylococcus aureus (MRSA)-induced osteomyelitis. The conjugations of drugs or bioactive molecules such as bone-morphogenetic protein-2 (BMP-2), vancomycin, calcitriol, dexamethasone, and cisplatin were able to enhance the osteogenic property of nHA. Thus, nHA is a promising delivery system for a variety of compounds in promoting bone regeneration in vivo.

Porous Nanomaterials Targeting Autophagy in Bone Regeneration

Porous nanomaterials (PNMs) are nanosized materials with specially designed porous structures that have been widely used in the bone tissue engineering field due to the fact of their excellent physical and chemical properties such as high porosity, high specific surface area, and ideal biodegradability. Currently, PNMs are mainly used in the following four aspects: (1) as an excellent cargo to deliver bone regenerative growth factors/drugs; (2) as a fluorescent material to trace cell differentiation and bone formation; (3) as a raw material to synthesize or modify tissue engineering scaffolds; (4) as a bio-active substance to regulate cell behavior. Recent advances in the interaction between nanomaterials and cells have revealed that autophagy, a cellular survival mechanism that regulates intracellular activity by degrading/recycling intracellular metabolites, providing energy/nutrients, clearing protein aggregates, destroying organelles, and destroying intracellular pathogens, is associated with the phagocytosis and clearance of nanomaterials as well as material-induced cell differentiation and stress. Autophagy regulates bone remodeling balance via directly participating in the differentiation of osteoclasts and osteoblasts. Moreover, autophagy can regulate bone regeneration by modulating immune cell response, thereby modulating the osteogenic microenvironment. Therefore, autophagy may serve as an effective target for nanomaterials to facilitate the bone regeneration process. Increasingly, studies have shown that PNMs can modulate autophagy to regulate bone regeneration in recent years. This paper summarizes the current advances on the main application of PNMs in bone regeneration, the critical role of autophagy in bone regeneration, and the mechanism of PNMs regulating bone regeneration by targeting autophagy.

Eggshell Derived Europium Doped Hydroxyapatite Nanoparticles for Cell Imaging Application

Hen's eggshell, a biological waste product, was turned into a cell imaging probe: europium doped hydroxyapatite (HAp: Eu) nanoparticle using hydrothermal method. Luminescence of the synthesized nanoparticle was studied for various doping concentrations of the lanthanide ion europium (Eu³⁺). Eu doped HAp showed a hexagonal crystal structure and rod-shaped morphology. Well-defined emission peaks of europium, corresponding to the substitution of Eu³⁺ at the Ca²⁺(I) site of HAp, were confirmed from the samples' photoluminescence (PL) spectra. Good biocompatibility up to 500 μg/mL of the samples indicates their potential applications in bioimaging. Synthesized nanoparticles were internalized and used for in vitro imaging of the PC12 cells without any surface modification. The materials' use as a potential in vivo imaging agent is proposed from the haemolysis study.

Antibacterial and Cellular Behaviors of Novel Zinc-Doped Hydroxyapatite/Graphene Nanocomposite for Bone Tissue Engineering

Bacteria are one of the significant causes of infection in the body after scaffold implantation. Effective use of nanotechnology to overcome this problem is an exciting and practical solution. Nanoparticles can cause bacterial degradation by the electrostatic interaction with receptors and cell walls. Simultaneously, the incorporation of antibacterial materials such as zinc and graphene in nanoparticles can further enhance bacterial degradation. In the present study, zinc-doped hydroxyapatite/graphene was synthesized and characterized as a nanocomposite material possessing both antibacterial and bioactive properties for bone tissue engineering. After synthesizing the zinc-doped hydroxyapatite nanoparticles using a mechanochemical process, they were composited with reduced graphene oxide. The nanoparticles and nanocomposite samples were extensively investigated by transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. Their antibacterial behaviors against Escherichia coli and Staphylococcus aureus were studied. The antibacterial properties of hydroxyapatite nanoparticles were found to be improved more than 2.7 and 3.4 times after zinc doping and further compositing with graphene, respectively. In vitro cell assessment was investigated by a cell viability test and alkaline phosphatase activity using mesenchymal stem cells, and the results showed that hydroxyapatite nanoparticles in the culture medium, in addition to non-toxicity, led to enhanced proliferation of bone marrow stem cells. Furthermore, zinc doping in combination with graphene significantly increased alkaline phosphatase activity and proliferation of mesenchymal stem cells. The antibacterial activity along with cell biocompatibility/bioactivity of zinc-doped hydroxyapatite/graphene nanocomposite are the highly desirable and suitable biological properties for bone tissue engineering successfully achieved in this work.