Application of magnetic nanoparticles for magnetic solid-phase extraction in preparing biological, environmental and food samples

Magnetic water treatment in a wastewater treatment plant: Part I - sorption and magnetic particles

The application of magnetic sorption to treat wastewaters is nowadays seen as a potential industrial method. In this work we apply magnetite particles to remediate real wastewater samples, with several contaminants competing for the same active sorption center at the same time. We also apply our studies at three different sampling points of a Wastewater Treatment Plant. In general terms, magnetite particles have shown a very good behaviour concerning the reduction of detergents and COD, while phosphates and total nitrogen, and the majority of heavy metals are high to moderately removed. The influence of the type of wastewater (i.e., sampling point) has also shown to be important especially for high concentration of contaminants.

Facile synthesis of magnetic molybdenum disulfide@graphene nanocomposite with amphiphilic properties and its application in solid-phase extraction for a wide polarity of insecticides in wolfberry samples

A novel magnetic molybdenum disulfide@graphene (Fe₃O₄/MoS₂@G) nanocomposite with amphiphilic properties was prepared via a co-mixing solvothermal method. To demonstrate the feasibility of Fe₃O₄/MoS₂@G as a sorbent during sample preparation, it was employed for the magnetic solid phase extraction (MSPE) of ten pyrethroids, three triazoles and two acaricide pyridaben and picoxystrobin in an emulsified aqueous solution. Dichloromethane was used as the extractant to form an emulsified aqueous solution. Subsequently, the Fe₃O₄/MoS₂@G sorbent with amphiphilic properties was used to retrieve 15 wide polarity insecticides from dichloromethane via MSPE. The proposed method has the advantage of being applicable to different polar pesticides, strengthening the capacity of enrichment and purification of target analytes. The π-π interaction between the hydrophilic and hydrophobic moieties of Fe₃O₄/MoS₂@G and the aromatic rings of target analytes were responsible for the efficient sorption. Thus, a reliable, convenient, and efficient method for the analysis of 15 insecticides with wide polarity in wolfberry samples was established by coupling Fe₃O₄/MoS₂@G nanocomposite MSPE with gas chromatography-mass spectrometry (GC-MS) analysis. The obtained linearity of this method was in the range from 1 to 5000 ng mL^-1 for 15 analytes, with determination coefficients (R²) ≥0.9907. The limit of detection (LOD) for 15 insecticides was in the range from 0.1 to 5.0 ng g^-1. The recoveries of 15 insecticides from spiked wolfberry samples were in the range from 71.41% to 110.53%, and RSD was less than 14.8%.

Determination of trigonelline in human plasma by magnetic solid-phase extraction: a pharmacokinetic study

Aim: To develop a novel method for the bioanalytical extraction of trigonelline (TRG) from human plasma samples using a magnetic nanocomposite and to evaluate its pharmacokinetic profile. Materials & methods: Magnetic bentonite/β-cyclodextrine (β-CD) nanoparticles, coupled with a validated ion-pairing reversed-phase high-performance liquid chromatography method, were used to determine TRG concentration from plasma samples following a single oral administration. Results: The developed reversed-phase high-performance liquid chromatography method was accurate, precise, specific, selective and reproducible. TRG showed rapid absorption, middle rate of elimination and mean residence time of ∼24 h. The data were best fitted on a two-compartment model in which t_max was 1.0 h, C_max 0.115 μg/ml, area under the curve (AUC)_0-24 1.72 μg/ml.h, Cl 0.0293 l/h/kg, t_1/2α 0.79 h, t_1/2β 13.68 h and k_a 1.63 h^-1. Conclusion: The findings of this study could provide useful information to promote the future study of TRG and aid optimal dose finding.

Highly selective enrichment and direct determination of imazethapyr residues from milk using magnetic solid-phase extraction based on restricted-access molecularly imprinted polymers

Restricted access media magnetic molecularly imprinted polymers (RAM-MMIPs) were prepared as magnetic solid phase extraction (M-SPE) material by reversible addition fragmentation chain transfer (RAFT) technique. The resulting RAM-MMIPs had a uniform, imprinted, hydrophilic layer (63 nm), good binding capacity (34.85 mg g-1) and satisfactory selectivity. In addition, these RAM-MMIPs had a robust ability to eliminate the interference of protein macromolecules. These RAM-MMIPs were then coupled with HPLC/UV to identify imazethapyr (IM) residues in untreated milk samples. Several major factors would affect M-SPE extraction efficiency, such as the amount of RAM-MMIPs, pH, extraction time of the sample solution, and the volume ratio of the elution solvent. Under the optimal conditions, the developed method had good linearity (R2 > 0.9993), low detection limit (2.13 μg L-1), and low quantitative limit (7.15 μg L-1). These results indicated this proposed approach is an efficient method for direct enrichment and detection of IM herbicides in milk and other biological samples.

Ionic covalent organic frameworks for the magnetic solid-phase extraction of perfluorinated compounds in environmental water samples

A novel magnetic ionic covalent organic framework (Fe₃O₄@EB-iCOFs) was designed and synthesized. It was then characterized by X-ray diffraction, N₂ adsorption-desorption analysis, and magnetic measurements, among others. The material shows the advantages of ionic property, large surface area, and magnetic responsiveness. It has potential of magnetic solid-phase extraction (MSPE) of perfluorinated compounds (PFCs). A method for the determination of PFCs based on MSPE-HPLC-MS/MS was established. The method has excellent linearity (r ≥ 0.995) in the working range 1-1000 ng L^-1 , good repeatability (1.4-5.8%, n = 6), low limits of detection in the range 0.1-0.8 ng L^-1 and satisfactory recoveries (between 73.9 and 108.3%).

Exploration of a Molecularly Imprinted Polymer (MIPs) as an Adsorbent for the Enrichment of Trenbolone in Water

The presence of endocrine disruptors in surface waters can have negative implications on wildlife and humans both directly and indirectly. A molecularly imprinted polymer (MIP) was explored for its potential to enhance the UV-Vis determination of trenbolone in water using solid-phase extraction (SPE). The synthesized MIP was studied using Fourier transform infrared spectra (FTIR) and scanning electron microscopy (SEM). Using the MIP resulted in a preconcentration and enrichment factor of 14 and 8, respectively. Trenbolone binding on the MIP was shown to follow a Langmuir adsorption and had a maximum adsorption capacity of 27.5 mg g−1. Interference studies showed that the MIP selectivity was not compromised by interferences in the sample. The MIP could be recycled three times before significant loss in analyte recovery.

Polyethyleneimine-modified magnetic carbon nanotubes as solid-phase extraction adsorbent for the analysis of multi-class mycotoxins in milk via liquid chromatography-tandem mass spectrometry

Polyethyleneimine-modified magnetic multi-walled carbon nanotubes were developed to extract 10 mycotoxins. Simple modification of polyethyleneimine was achieved on the magnetic substrate by using an epoxy-containing silane agent as a linker. The resultant magnetic adsorbent was integrated with reverse phase and anion exchange interaction sites. Under optimal extraction conditions, only 20.0 mg adsorbent was used to extract the mycotoxins from 50.0 mL loading solution. The maximum adsorption capacities of the adsorbent toward the mycotoxins ranged from 4.9 to 10.2 mg/g. Adsorption and desorption were completed within 3.0 and 2.0 min, respectively. The adsorbent could be used for six repeated runs without evident change in extraction performance. The adsorbent combined with liquid chromatography-tandem mass spectrometry was applied further to analyze the mycotoxins in milk. The absolute recoveries of the 10 mycotoxins ranged from 88.3 to 103.5% with relative standard deviations that ranged from 2.4 to 6.5%, and their limits of detection were 0.003 to 0.442 μg/kg. The proposed adsorbent has great potential in the routine analysis of mycotoxins in ordinary analytical chemistry laboratory.

Application of Multiplexed Aptasensors in Food Contaminants Detection

The existence of contaminants in food poses a serious threat to human health. In recent years, aptamer sensors (aptasensors) have been developed rapidly for the detection of food contaminants because of their high specificity, design flexibility, and high efficiency. However, the development of high-throughput, highly sensitive, on-site, and cost-effective methods for simultaneous detection of food contaminants is still restricted due to multiple signal overlap or mutual interference and cross-reaction between different analytes with similar molecular structures. To overcome these problems, this Review summarizes some effective strategies from the articles published in recent years about multiplexed aptasensors for the simultaneous detection of food contaminants. This work focuses on the application of multiplexed aptasensors to simultaneously detect antibiotics, pathogens, and mycotoxins in food. These aptasensors mainly contain fluorescent aptasensors, electrochemical aptasensors, surface-enhanced Raman scattering-based aptasensors, microfluidic chip aptasensors, and paper-based multiplexed aptasensors. In addition, this Review also covers the application of nucleic acid cycle amplification and nanomaterial amplification strategies to improve the detection sensitivity. Finally, the limitations and challenges in the design of multiplexed aptasensor are also taken into account.

Microextraction Techniques with Deep Eutectic Solvents

In this review, the ever-increasing use of deep eutectic solvents (DES) in microextraction techniques will be discussed, focusing on the reasons needed to replace conventional extraction techniques with greener approaches that follow the principles of green analytical chemistry. The properties of DES will be discussed, pinpointing their exceptional performance and analytical parameters, justifying their current extensive scientific interest. Finally, a variety of applications for commonly used microextraction techniques will be reported.

Insights into the structure-performance relationships of extraction materials in sample preparation for chromatography

Sample preparation is one of the most crucial steps in analytical processes. Commonly used methods, including solid-phase extraction, dispersive solid-phase extraction, dispersive magnetic solid-phase extraction, and solid-phase microextraction, greatly depend on the extraction materials. In recent decades, a vast number of materials have been studied and used in sample preparation for chromatography. Due to the unique structural properties, extraction materials significantly improve the performance of extraction devices. Endowing extraction materials with suitable structural properties can shorten the pretreatment process and improve the extraction efficiency and selectivity. To understand the structure-performance relationships of extraction materials, this review systematically summarizes the structural properties, including the pore size, pore shape, pore volume, accessibility of active sites, specific surface area, functional groups and physicochemical properties. The mechanisms by which the structural properties influence the extraction performance are also elucidated in detail. Finally, three principles for the design and synthesis of extraction materials are summarized. This review can provide systematic guidelines for synthesizing extraction materials and preparing extraction devices.

Magnetic dispersive solid-phase extraction using ZSM-5 zeolite/Fe2O3 composite coupled with screen-printed electrodes based electrochemical detector for determination of cadmium in urine samples

A novel, simple, fast, sensitive and environmentally friendly approach is presented to determine cadmium in urine samples, combining magnetic dispersive solid-phase extraction (MDSPE) for sample preparation and screen-printed carbon electrodes (SPCEs) for square-wave anodic stripping voltammetry. This association involves the miniaturization of sample preparation and measurement process. Firstly, cadmium was extracted directly from urine samples employing a ZSM-5/Fe₂O₃, then, the composite enriched with cadmium was deposited onto the SPCE and finally covered with a suitable electrolyte for electrochemical detection. Thereby, the elution and detection of cadmium were carried out in a single step. To optimize experimental parameters affecting MDSPE, a two-step multivariate strategy has been employed. The method has been evaluated under optimized extraction/elution conditions (i.e., type of sorbent, ZSM-5/Fe₂O_3; amount of sorbent, 10 mg; sample pH, 6.8; extraction time, 5.5 min; and HCl concentration, 0.5 M) using standard addition calibration. Standard addition calibration curves gave a good linearity in the range from 0 to 30 μg L^-1 with correlation coefficients ranging from 0.997 to 0.998 (N = 7). The limit of detection, evaluated empirically and statistically, ranged from 0.5 to 1.0 μg L^-1 and from 0.4 to 0.8 μg L^-1, respectively, which are lower than the threshold level established by the Ministry of Labour and Social Affairs (Spain) and World Health Organization for normal cadmium content in urine (i.e., 3.4 and 4.0 μg L^-1, respectively). The repeatability of the proposed method was evaluated at 5 and 20 μg L^-1 spiking levels obtaining coefficients of variation ranged between 12 and 15% (n = 6). A certified reference material (REC-8848/Level II) was analyzed to assess method accuracy finding 92% and 1.3 μg L^-1 as the recovery (trueness) and standard deviation values, respectively. Finally, the method was applied to spiked urine samples, obtaining good agreement between spiked and found concentrations (recovery ranged from 89 to 98% and CV values ranged from 7% to 14%). Therefore, this is a new and successful contribution to the portable total analytical systems.

Development of a sample pretreatment device integrating ultrasonication, centrifugation and ultrafiltration, its application on rapid on-site screening of illegally added chemical components in heat-clearing, detoxicating Chinese patent medicines followed by electrospray ionization-ion mobility spectrometry

In this paper, a simple and rapid sample pretreatment device integrating ultrasonication, centrifugation and ultrafiltration (UCU) was reported for preparation of trace analytes in complex matrices. The UCU device was composed of two parts, A and B. The sample and extraction solvent were put into Part B for ultrasonic extraction. Subsequently, Part A and Part B were integrated and sealed for centrifugation and ultrafiltration. Finally, the ultrafiltrate in Part A was taken out for subsequent detection. After optimization, the device was applied to rapid on-site screening of five illegally added chemical components in heat-clearing and detoxicating Chinese patent medicines by combining with electrospray ionization-ion mobility spectrometry (ESI-IMS). The method showed good performance in terms of linearity with correlation coefficients (R²) above 0.9976 and limits of detection (LODs) in the range of 0.049-0.391 μg mL^-1. The recoveries were from 96.5 % to 100.8 %. The whole analysis process was within 11 min. The proposed method was further compared with other methods reported in the literature and the advantages and considerations were also explored. The results demonstrated that it was a simple, fast and accurate technique. The establishment of this method not only greatly improved the experimental efficiency but also avoided potential sample pollution brought by multiple sample transfer, and could provide a powerful means for rapid on-site analysis of trace analytes in complex matrices.

Synthesis of Magnetic Metal-Organic Frame Material and Its Application in Food Sample Preparation

A variety of contaminants in food is an important aspect affecting food safety. Due to the presence of its trace amounts and the complexity of food matrix, it is very difficult to effectively separate and accurately detect them. The magnetic metal-organic framework (MMOF) composites with different structures and functions provide a new choice for the purification of food matrix and enrichment of trace targets, thus providing a new direction for the development of new technologies in food safety detection with high sensitivity and efficiency. The MOF materials composed of inorganic subunits and organic ligands have the advantages of regular pore structure, large specific surface area and good stability, which have been thoroughly studied in the pretreatment of complex food samples. MMOF materials combined different MOF materials with various magnetic nanoparticles, adding magnetic characteristics to the advantages of MOF materials, which are in terms of material selectivity, biocompatibility, easy operation and repeatability. Combined with solid phase extraction (SPE) technique, MMOF materials have been widely used in the food pretreatment. This article introduced the new preparation strategies of different MMOF materials, systematically summarizes their applications as SPE adsorbents in the pretreatment of food contaminants and analyzes and prospects their future application prospects and development directions.

Recent applications of magnetic solid phase extraction in sample preparation for phytochemical analysis

Sample preparation such as isolation and pre-concentration is a crucial step for the phytochemical analysis. Magnetic solid-phase extraction (MSPE) has received considerable attention, mainly due to its phase separation more conveniently by facile magnetic decantation as compared to traditional SPE. This review focused on the recent applications of MSPE in sample preparation for the analysis of phytochemical compounds in plants, biological samples and Chinese herbal preparations. In addition, the enzymes immobilized on the magnetic materials and used for the biospecific extraction of enzyme inhibitors were also discussed. The information summarized in this article may provide a reference to the further applications of MSPE in phytochemical analysis.

Synthesis of Magnetic Molecularly Imprinted Polymer Sorbents for Isolation of Parabens from Breast Milk

Magnetic molecularly imprinted polymers (MMIPs) are an invaluable asset in the development of many methods in analytical chemistry, particularly sample preparation. Novel adsorbents based on MMIPs are characterized by high selectivity towards a specific analyte due to the presence of a specific cavity on their polymer surface, enabling the lock-key model interactions to occur. In addition, the magnetic core provides superparamagnetic properties that allow rapid separation of the sorbent from the sample solution. Such a combination of imprinted polymers with a magnetic core has an innovative influence on the development of separation techniques. Hence, the present study describes the synthesis of MMIPs with 17β-estradiol used as a template molecule in the production of imprinted polymers. The as-prepared sorbent was used for a sorption/desorption study of five parabens from breast milk samples. The obtained results were characterized by sorption efficiency exceeding 92%, which shows the high affinity of the analytes to the functional groups on the sorbent. The final determination of the selected analytes was done with high-performance liquid chromatography using a fluorometric detector. The determined linearity ranges for selected parabens were characterized by high determination coefficients (r² from 0.9992 to 0.9999), and the calculated limit of detection (LOD) and limit of quantification (LOQ) for the identified compounds were low (LOD from 1.1-2.7 ng mL^-1; LOQ from 3.6-8.1 ng mL^-1), which makes their quantitative analysis in real samples feasible.

Effective enrichment and detection of trace polybrominated diphenyl ethers in water samples based on magnetic covalent organic framework nanospheres coupled with chromatography-mass spectrometry

Novel core shell structured magnetic covalent organic frameworks were synthesized at room temperature and first applied in water samples for the enrichment of trace polybrominated diphenyl ethers (PBDEs) through magnetic solid-phase extraction. The prepared materials were characterized through transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, vibrating sample magnetometer and X-ray photoelectron spectroscopy. During adsorption, the parameters affecting extraction and desorption efficiency were further optimized. Combined gas chromatography and mass spectrometry (GC/MS) revealed that high enrichment factors (275-292), low limits of detection (0.12-0.38 ng·L-1), wide linear ranges (0.5-1000 ng·L-1), and good reproducibility (intra-day 1.40%-4.31% and inter-day 5.14%-9.12%) were obtained under optimal conditions. The method successfully detected PBDEs in different water samples.

Nano-sized magnetic Ni particles based dispersive solid-phase extraction of trace Cd before the determination by flame atomic absorption spectrometry with slotted quartz tube: a new, accurate, and sensitive quantification method

In this study, a new analytical strategy was developed to determine trace cadmium in aqueous samples with high sensitivity and accuracy. A combination of magnetic nickel nanoparticles (Ni-MNPs) based dispersive solid-phase extraction (DSPE) and flame atomic absorption spectrometry fitted with a slotted quartz tube (SQT-FAAS) lowered the detection limit of cadmium. The magnetic Ni nanoparticles were synthesized, characterized, and thoroughly optimized in a stepwise approach. The quartz tube was custom cut in the laboratory to suit the specifics of the flame burner. Using the optimized conditions, a limit of detection value of 0.58 μg/L and limit of quantification value of 1.93 μg/L were obtained. To demonstrate accuracy and applicability of the developed method, well water samples were analyzed for their Cd content, and matrix effect on the extraction yield was investigated. The percent recovery results calculated ranged from 93.8 to 108.2%, with corresponding standard deviation values ranging from 1.7 to 7.7. These results established the developed method as sensitive, accurate, and precise for determination of cadmium at trace levels.

Magnetic solid-phase extraction as a novel method for the prediction of the bioaccessibility of polycyclic aromatic hydrocarbons

Chemical methods used to predict the bioaccessibility of hydrophobic organic compounds (HOCs) still need further development and improvement. In this work, magnetic solid-phase extraction (MSPE) based on poly(β-cyclodextrin)-coated magnetic polydopamine (Fe₃O₄@PDA@PCD) was first introduced to assess the bioaccessibility of polycyclic aromatic hydrocarbons (PAHs) in soils. Due to its good hydrophilicity and submicrometer scale, Fe₃O₄@PDA@PCD displayed a higher extraction rate for PAHs in an aqueous solution (equilibrium time < 5 min) than Tenax resin, which had an equilibrium time longer than 30 min. The merits of Fe₃O₄@PDA@PCD are beneficial to accelerate the desorption of PAHs from soil, especially for high molecular weight PAHs, in which the amounts extracted by Fe₃O₄@PDA@PCD were 1.2-2.8 times higher than those extracted by Tenax resin. The desorption kinetics data were well fitted with a two- or three-fraction model. The fitting results indicated that the MSPE method can be used to predict the bioaccessible fractions of PAHs. By comparing the prediction results obtained from the MSPE method with bioassays using earthworms, a significant linear correlation (R² = 0.98) with a slope statistically close to 1 was obtained. These results suggested that the MSPE method can act as a simple and efficient method to measure the bioaccessibility of PAHs in soil.

A novel magnetic solid-phase extraction method for detection of 14 heterocyclic aromatic amines by UPLC-MS/MS in meat products

The current study developed a cheap and effective method for the simultaneous extraction of 14 heterocyclic aromatic amines (HAAs) in food matrix. Core-shell Fe₃O₄@PDA nanoparticles were constructed and acted as the magnetic solid-phase extraction adsorbent to separate and purify HAAs from meat products for the first time. Then, UPLC-MS/MS technique was employed to identify and quantify the HAAs easily. Fe₃O₄@PDA nanoparticles were synthesized and characterized successfully. Totally 14 HAAs were completely separated in 19.99 min with good regression coefficients. LODs and LOQs were in the range of 0.013-0.247 ng/g and 0.056-0.803 ng/g, respectively. The intra-day precisions and inter-day precisions were below 9%. Except for IQ[4,5-b], Phe-p-1, PhIP, other 11 types of HAAs (DMIP, 1,5,6-TMIP, IQ, IQx, MeIQ, MeIQx, 7,8-DiMeIQx, AαC, MeAαC, Harman, Norharman) could acquire relatively high recoveries (71.06%-108.49%). The proposed method was successfully devoted to the evaluation of HAAs levels in 8 commercial meat products to verify the adaptability.

Sample treatment based on molecularly imprinted polymers for the analysis of veterinary drugs in food samples: a review

The use of veterinary drugs in medical treatments and in the livestock industry is a recurrent practice. When applied in subtherapeutic doses over prolonged times, they can also act as growth promoters. However, residues of these substances in foods present a risk to human health. Their analysis is thus important and can help guarantee consumer safety. The critical point in each analytical technique is the sample treatment and the analytical matrix complexity. The present manuscript summarizes the development, type of synthesis, characterization, and application of molecularly imprinted polymers in the separation, identification, and quantification techniques for the determination of veterinary drug residues in food samples in extraction, clean-up, isolation, and pre-concentration systems. Synthesized sorbents with specific recognition properties improve the interactions between the analytes and the polymeric sorbents, providing better analysis conditions and advantages in comparison with commercial sorbents in terms of high selectivity, analytical sensitivity, easy performance, and low cost analysis.

Development of a magnetic dispersive micro-solid-phase extraction method based on a deep eutectic solvent as a carrier for the rapid determination of meloxicam in biological samples

In this study, an environmentally friendly magnetic dispersive micro solid-phase extraction was developed based on a deep eutectic solvent as a carrier and disperser of ferrofluids for the isolation and pre-concentration of meloxicam from biological samples. The extracted analyte was then analyzed by high performance liquid chromatography with ultraviolet detection (HPLC-UV). The ferrofluid was prepared via a combination of silica-coated magnetic nanoparticles and an ethylene glycol/choline chloride deep eutectic solvent as a carrier. In this method, the rapid injection of the magnetic nanoparticles into the sample solution using a green carrier liquid increased the contact surface between the adsorbent and the target analyte which reduced the amount of the adsorbent and extraction time. A fractional factorial design was used for screening some effective parameters such as the amount of SiO2@Fe3O4, extraction time, pH of the sample solution, amount of the salt, volume of the desorption solvent, and desorption time. The effective parameters were then optimized by central composite design. Optimized extraction conditions were: amount of SiO2@Fe3O4 of 2 mg; extraction time of 1 min; pH of the sample solution of 4; volume of the desorption solvent of 200 μL; and desorption time of 2 min. Under the optimal conditions, wide linear ranges of 5-500 μg L-1 for water and 10-500 μg L-1 were obtained for urine and plasma samples with acceptable extraction recoveries above 89.2%. Limit of detections (LODs) were in the range of 1.5-3.0 μg L-1. The enrichment factors achieved were above 44.6 with relative standard deviations lower than 6.2%.

Quantitative determination of trace phenazopyridine in human urine samples by hyphenation of dispersive solid-phase extraction and liquid-phase microextraction followed by gas chromatography/mass spectrometry analysis

Magnetic dispersive solid-phase extraction followed by dispersive liquid-liquid microextraction coupled with gas chromatography/mass spectrometry was applied for the quantitative analysis of phenazopyridine in urinary samples. Magnetic dispersive solid-phase extraction was carried out using magnetic graphene oxide nanoparticles modified by poly(thiophene-pyrrole) copolymer. The eluting solvent of this step was used as the disperser solvent for the dispersive liquid-liquid microextraction procedure. To reach the maximum efficiency of the method, effective parameters including sorbent amount, adsorption time, type and volume of disperser and extraction solvents, pH of the sample solution, and ionic strength as well as desorption time, and approach were optimized, separately. Characterization of the synthesized sorbent was studied by utilizing infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray analysis. Calibration curve was linear in the range of 0.5-250 ng/mL (R²  = 0.9988) with limits of detection and quantification of 0.1 and 0.5 ng/mL, respectively. Intra- and interday precisions (RSD%, n = 3) of the method were in the range of 4.6-5.4% and 4.0-5.5%, respectively, at three different concentration levels. Under the optimal condition, this method was successfully applied for the determination of phenazopyridine in human urine samples. The relative recoveries were obtained in the range of 85.0-89.0%.

Magnetic C60 nanospheres based solid-phase extraction coupled with isotope dilution gas chromatography-mass spectrometry method for the determination of sixteen polycyclic aromatic hydrocarbons in Chinese herbal medicines

C₆₀-based magnetic nanospheres were synthesized by coating Fe₃O₄ nanospheres with silica, then modifying with 3-aminopropyltriethoxysilane as a linker and a C₆₀ fullerene stationary phase. The morphologies, magnetic properties, infrared absorption and carbon content of magnetic nanospheres were studied by TEM, VSM, FTIR and carbon and sulfur analyzer. The magnetic nanospheres were employed for the magnetic solid-phase extraction (MSPE) of 16 polycyclic aromatic hydrocarbons (PAHs) in nine Chinese herbal medicines. The analyses were conducted by isotope dilution gas chromatography-mass spectrometry. The main parameters influencing the extraction, including extraction solvent, adsorbent amount, and extraction time were optimized. Method validation showed that the limit of detection (LOD) was 0.02-0.11 µg/kg, and the limit of quantification (LOQ) was 0.07-0.36 µg/kg. The spiked recoveries rates for 16 PAHs in white peony root were 84.7-107.2%. The relative standard deviation (RSD) was 1.7-8.4%. The established method was further used for the determination 16 PAHs in nine Chinese herbal medicines. Total content of 16 PAHs varied from 73.6 µg/kg (fructus lycii) to 2172.6 µg/kg (astragalus root). The results indicate that the pollution of PAHs in Chinese herbal medicines is serious. The established method can effective detect PAHs contamination in Chinese herbal medicines.

Magnetic nanoparticles assisted dispersive liquid-liquid microextraction of chloramphenicol in water samples

This work describes the development of a new methodology based on magnetic nanoparticles assisted dispersive liquid-liquid microextraction (DLLME-MNPs) for preconcentration and extraction of chloramphenicol (CAP) antibiotic residues in water. The approach is based on the use of decanoic acid as the extraction solvent followed by the application of MNPs to magnetically retrieve the extraction solvent containing the extracted CAP. The coated MNPs were then desorbed with methanol, and the clean extract was analysed using ultraviolet-visible spectrophotometry. Several important parameters, such as the amount of decanoic acid, extraction time, stirring rate, amount of MNPs, type of desorption solvent, salt addition and sample pH, were evaluated and optimized. Optimum parameters were as follows: amount of decanoic acid: 200 mg; extraction time: 10 min; stirring rate: 800 rpm; amount of MNPs: 60 mg; desorption solvent: methanol; salt: 10%; and sample pH, 8. Under the optimum conditions, the method demonstrated acceptable linearity (R ² = 0.9933) over a concentration range of 50-1000 µg l^-1. Limit of detection and limit of quantification were 16.5 and 50.0 µg l^-1, respectively. Good analyte recovery (91-92.7%) and acceptable precision with good relative standard deviations (0.45-6.29%, n = 3) were obtained. The method was successfully applied to tap water and lake water samples. The proposed method is rapid, simple, reliable and environmentally friendly for the detection of CAP.

Trends in sensitive detection and rapid removal of sulfonamides: A review

Sulfonamides in environmental water, food, and feed are a major concern for both aquatic ecosystems and public health, because they may lead to the health risk of drug resistance. Thus, numerous sensitive detection and rapid removal methodologies have been established. This review summarizes the sample preparation techniques and instrumental methods used for sensitive detection of sulfonamides. Additionally, adsorption and photocatalysis for the rapid removal of sulfonamides are also discussed. This review provides a comprehensive perspective on future sulfonamide analyses that have good performance, and on the basic methods for the rapid removal of sulfonamides.

Integration of Fe3O4@UiO-66-NH2@MON core-shell structured adsorbents for specific preconcentration and sensitive determination of aflatoxins against complex sample matrix

Aflatoxins have been a hot topic in the field related into public health and ecosystem protection, and great effort has been made in developing of adsorptive materials for effective probing the target aflatoxins. Conventional materials, like metal-organic frameworks (MOFs) showed promising application in separation science. However, the cumbersome separation process, competitive adsorption are also major challenges. Regarding this, a novel magnetic micro-composite denoted as Fe₃O₄@UiO-66-NH₂@MON with core-shell structure was constructed. The core of Fe₃O₄ microspheres was coated with MOFs crystals, and then microporous organic network (MON) was introduced onto the surface of Fe₃O₄@UiO-66-NH₂ through a sonogashira coupling reaction. It exhibited good magnetic separation ability, which effectively simplified the pre-treatment steps. The proposed method possessed excellent selectivity and sensitivity, with detection limits in the range of 0.15-0.87 μg L^-1 combination with HPLC analysis. More importantly, the MON coating significantly improved the hydro-stability of whole adsorbents, thus enhancing the adsorption efficiency and favoring the practical application of the materials. The developed Fe₃O₄@UiO-66-NH₂@MON-based solid extraction method has been well-applied for real sample analysis, with the recovery of 87.3%-101.8%. We believe the newly-constructed hybrid nano-adsorbents hold great potential in further application in various analytical methods for different target analytes.

Comparative Study of Synthesis Methods to Prepare New Functionalized Adsorbent Materials Based on MNPs-GO Coupling

In this work, the synthesis of new adsorbent nanomaterials based on the coupling of magnetic nanoparticles and graphene oxide (MNPs-GO) was addressed. Separately, MNPs and GO have adsorbent properties of great interest, but their use involves certain difficulties. The coupling seeks compensation for their disadvantages, while maintaining their excellent properties. Three different routes to synthesize coupled MNPs-GO were studied and are compared in this work. The three synthesized materials were functionalized with chelating groups: [1,5-bis (di-2-pyridyl) methylene] thiocarbonohydrazide (DPTH) and [1,5-bis(2-pyridyl)3-sulfophenylmethylene] thiocarbonohydrazide (PSTH). The new adsorbent nanomaterials were characterized adequately. Moreover, their capacities of adsorption toward heavy and noble metals were determined, in order to apply them as extractants in magnetic solid-phase extraction to preconcentrate metals in environmental samples. The results showed that one of the routes provided nanomaterials with better adsorbent characteristics and higher yields of functionalization.

Transforming lanthanide and actinide chemistry with nanoparticles

Lanthanides and actinides are used in a wide variety of applications, from energy production to life sciences. To address toxicity issues due to the chemical, and often radiological, properties of these elements, methods to quantify and recover them from industrial waste are necessary. When used in biomedicine, lanthanides and actinides are incorporated in compounds that show promising therapeutic and/or bioimaging properties, but lack robust strategies to target cancer and other pathologies. Furthermore, current decorporation protocols to respond to accidental actinide exposure rely on intravenous injections of soluble chelating agents, which are inefficient for treatment of inhaled radionuclides trapped in lungs. In recent years, nanoparticles have emerged as powerful tools in both industry and clinical settings. Because some inorganic nanoparticles are sensitive to external stimuli, such as light and magnetic fields, they can be used as building blocks for sensitive bioassays and separation techniques. In addition, nanoparticles can be functionalized with multiple ligands and act as carriers for selective delivery of therapeutic and contrast agents. This review summarizes and discusses recent progress on the use of nanoparticles in lanthanide and actinide chemistry. We examine different types of nanoparticles based on composition, functionalization, and properties, and we critically analyze their performance in a comparative mode. Our focus is two-pronged, including the nanoparticles free of lanthanides and actinides that are used for the detection, separation, or decorporation of f-block elements, as well as the nanoparticles that enhance the inherent properties of lanthanides and actinides for therapeutics, imaging and catalysis.

Zeolitic imidazolate framework-8 coated Fe3O4@SiO2 composites for magnetic solid-phase extraction of bisphenols

A new magnetic composite material ZIF-8 coated Fe₃O₄@SiO₂ was employed for preconcentration and detection of trace BPs in water and plastic products.