Surface chemistry, morphological analysis and properties of cellulose nanocrystals with gradiented sulfation degrees

Preparation and characterization of semi-IPNs of polycaprolactone/poly (acrylic acid)/cellulosic nanowhisker as artificial articular cartilage

Cartilage is a semi-solid resilient and smooth elastic connective tissue and upon damage, its repair is almost impossible or occurs with a very slow recovery process. Polycaprolactone (PCL), used as a biocompatible polymer, withholds all required mechanical properties, except suitable cell adhesion due to its hydrophobicity. In order to resolve this issue, we sought to introduce appropriate semi-IPNs into the system to regain its hydrophilicity base on increasing of the hydrophilic polymer. PCL and Cellulose nanowhiskers (CNWs) were entrapped in a network of poly (acrylic acid) that had been crosslinked via a novel acrylic-urethane crosslinker. The influential synthetic parameters on the preparation of artificial articular cartilages were investigated based on the Taguchi test design. The prepared CNW, acrylic-urethane crosslinker and semi-IPNs were studied via ¹H NMR, FTIR, SEM, TEM, TGA, water swelling, water contact angle, tensile, and MTT analyses. According to the results, the optimal amount of monomer was about 46%. Incorporation of an optimized amount of CNW, which was 0.5%, improved the mechanical properties of artificial cartilage. After a 30 h time period, semi-IPNs showed the water absorption of about 30%. MTT on days 1, 3 and 5, as well as cell attachment, confirmed the biocompatibility of the semi-IPNs.

Alkali Hydrolysis of Sulfated Cellulose Nanocrystals: Optimization of Reaction Conditions and Tailored Surface Charge

Cellulose nanocrystals (CNCs) are a biorenewable resource, which may be chemically modified to impart specific properties. Modified CNCs have found use in imaging applications, as rheology modifiers, polymer reinforcements, barrier and/or optical films, and nanocomposites. Nanoparticle dimensions of CNCs are typically 5-10 nm in width, with lengths of <100-300 nm. However, the physical properties are dependent upon the number and nature of the surface charge groups imparted during preparation. In the case of CNCs produced from sulfuric acid hydrolysis, the sulfated surface groups may be partially removed prior to further functionalization. This gives more available hydroxyls yet renders the CNCs less colloidally stable. Furthermore, conditions vary significantly and there is no consensus about the optimal conditions for partial removal of sulfate functionality or conditions developed to give specific surface charge. In the following, alkali hydrolysis of sulfate half-esters was quantified by conductometric titration of the strong acid groups, and using a design of experiments (DOE), optimal conditions were determined to produce CNCs with tailored surface charge.

Facile extraction of cellulose nanocrystals

A simple process for extracting cellulose nanocrystals (CNCs) is proposed that only uses high-pressure homogenization (HPH) controlling a process temperature. The proposed process was assessed and compared with normal production through acidic hydrolysis. Temperature-controlled HPH produced CNCs with high crystallinity, which linearly increased with increasing process temperature over 20 passes. The CNCs had uniform widths and lengths in the ranges of 4-14 nm and 60-320 nm, respectively. Undesirable chemical reaction can be avoided with the proposed process because no chemical was used to promote the CNC extraction. This method is an efficient and sustainable green approach to CNC production.

An Effective, Economical and Ultra-Fast Method for Hydrophobic Modification of NCC Using Poly(Methylhydrogen)Siloxane

Poor compatibility between nanocellulose crystals (NCCs) and major polymers has limited the application of NCC as bio-reinforcements. In this work, an effective and ultra-fast method was investigated to significantly improve the hydrophobicity of NCC by using poly(methylhydrogen)siloxane (PMHS) as modifier. PMHS possessed amounts of reactive -Si-H groups and hydrophobic -CH₃ groups. The former groups were reactive with the hydroxyl groups of NCC, while the latter groups afforded NCC very low surface energy. As the weight ratio of PMHS to NCC was only 0.0005%, the hydrophobicity of NCC was significantly improved by increasing the water contact angle of NCC from 0° to 134°. The effect of weight ratio of PMHS to NCC and the hydrogen content of -Si-H in PMHS on the hydrophobicity and thermal stability was investigated in detail by Fourier transform infrared spectroscopy (FTIR), (X-ray Diffraction) XRD and (thermogravimetric analysis) TGA. The results indicated that PMHS chains were covalently grafted onto NCC and PMHS modification improved the thermal stability of NCC.

Polymer Composites Reinforced with Natural Fibers and Nanocellulose in the Automotive Industry: A Short Review

Environmental concerns and cost reduction have encouraged the use of natural fillers as reinforcement in polymer composites. Currently, a wide variety of reinforcement, such as natural fibers and nanocellulose, are used for this purpose. Composite materials with natural fillers have not only met the environmental appeal, but also contribute to developing low-density materials with improved properties. The production of natural fillers is unlimited around the world, and many species are still to be discovered. Their processing is considered beneficial since the natural fillers do not cause corrosion or great wear of the equipment. For these reasons, polymer reinforced with natural fillers has been considered a good alternative for obtaining ecofriendly materials for several applications, including the automotive industry. This review explores the use of natural fillers (natural fibers, cellulose nanocrystals, and nanofibrillated cellulose) as reinforcement in polymer composites for the automotive industry.

Binding Forces of Cellulose Binding Modules on Cellulosic Nanomaterials

In this study, the interaction forces between different cellulosic nanomaterials and a protein domain belonging to cellulose binding modules family 1 (CBM1) were investigated at the molecular scale. Cellulose binding modules are protein domains found in carbohydrate active enzymes having an affinity toward cellulosic materials. Here, the binding force of a fusion protein containing a cellulose binding module (CBM1) produced recombinantly in E. coli was quantified on different cellulose nanocrystals immobilized on surfaces. Adhesion of the CBM on cellulose with different degrees of crystallinity as well as on chitin nanocrystals was examined. This study was carried out by single molecule force spectroscopy using an atomic force microscope, which enables the detection of binding force of individual molecules. The study contains a preliminary quantification of the interactions at the molecular level that sheds light on the development of new nanocellulose-based nanocomposites with improved strength and elasticity.

Effect of template type on the preparation of the emeraldine salt form of polyaniline (PANI-ES) with horseradish peroxidase isoenzyme C (HRPC) and hydrogen peroxide

Horseradish peroxidase isoenzyme C (HRPC) is often used as catalyst for the preparation of the conductive emeraldine salt form of polyaniline (PANI-ES) from aniline and hydrogen peroxide (H₂O₂) in the presence of anionic templates in aqueous solution. Here, a direct comparison of three types of soft templates was made, (i) the sodium salt of sulfonated polystyrene (SPS), (ii) micelles from sodium dodecylbenzenesulfonate (SDBS), and (iii) vesicles from either a 1 : 1 molar mixture of SDBS and decanoic acid or from AOT (sodium bis(2-ethylhexyl)sulfosuccinate). Based on UV/vis/NIR, EPR and Raman spectroscopy measurements all three types of templates are similarly suitable, with advantages of the two vesicle systems in terms of aniline conversion degree and radical content in the final PANI-ES product. First experiments with sulfated cellulose nanocrystals (CNCs) indicate that they are promising rigid templates for the preparation of electroconductive PANI-ES-coated cellulose materials or devices.

Different types of templates consisting of sulfonate or sulfate groups were compared for the horseradish peroxidase/H₂O₂-catalysed synthesis of the emeraldine salt form of polyaniline from aniline at pH = 4.3.

Convenient Synthesis of Hybrid Polymer Materials by AGET-ATRP Polymerization of Pickering Emulsions Stabilized by Cellulose Nanocrystals Grafted with Reactive Moieties

We report a novel method to prepare capsules, beads, or open-cell materials from Pickering emulsions of monomers, stabilized by cellulose nanocrystals (CNCs) grafted with reactive isobutyrate bromide moieties (CNC-Br). CNC-Br particles with different hydrophilic/hydrophobic balance at their surface were prepared and subsequently used to stabilize direct (O/W), inverted (W/O), or double emulsions of styrene or n-BuA. The different emulsions obtained were subsequently polymerized, by initiating an AGET-ATRP polymerization from the brominated particles surrounding the stabilized droplets. The different hybrid polymer materials obtained were subsequently characterized, and the impact of the CNCs functionalization and polymerization conditions was particularly discussed.

Preparation and Characterization of Polyvinylpyrrolidone/Cellulose Nanocrystals Composites

Composite films and aerogels of polyvinylpyrrolidone/cellulose nanocrystals (PVP/CNC) were prepared by solution casting and freeze-drying, respectively. Investigations into the PVP/CNC composite films and aerogels over a wide composition range were conducted. Thermal stability, morphology, and the resulting reinforcing effect on the PVP matrix were explored. FTIR, TGA, DSC, X-ray diffraction, SEM, and tensile testing were used to examine the properties of the composites. It was revealed PVP-assisted CNC self-assembly that produces uniform CNC aggregates with a high aspect ratio (length/width). A possible model of the PVP-assisted CNC self-assembly has been considered. Dispersibility of the composite aerogels in water and some organic solvents was studied. It was shown that dispersing the composite aerogels in water resulted in stable colloidal suspensions. CNC particles size in the redispersed aqueous suspensions was near similar to the CNC particles size in never-dried CNC aqueous suspensions.

Star-like Supramolecular Complexes of Reducing-End-Functionalized Cellulose Nanocrystals

In this work, we take advantage of the parallel organization of cellulose chains in cellulose I yielding an inherent chemical asymmetry of cellulose nanocrystals, i.e., reducing vs nonreducing end, to selectively modify only one end of these rigid rodlike crystals to be used as a linking point for the formation of supramolecular structures. We have prepared biotin-functionalized tunicate cellulose nanocrystals at the reducing end capable of forming new complex supramolecular hierarchies by the addition of the protein streptavidin. Biotin-streptavidin coupling was chosen because streptavidin has a multivalency of four and the biotin-streptavidin bond is known to be highly selective and stable. Hence, streptavidin molecules would link up to four cellulose nanocrystals through their biotin-modified reducing end. Two biotin derivatives were studied, consisting of an anchoring group, i.e., amine or hydrazine; the biotin moiety; and the linker between them. Results show that the length of the linker significantly affects the bond between the biotinylated cellulose nanocrystals and streptavidin, and a certain chain length is necessary for the supramolecular assembly of several cellulose nanocrystals by streptavidin.

Hydrophobic Modification of Nanocellulose via a Two-Step Silanation Method

Dodecyltrimethoxysilane (DTMOS), which is a silanation modifier, was grafted onto nanocellulose crystals (NCC) through a two-step method using KH560 (ɤ-(2,3-epoxyproxy)propytrimethoxysilane) as a linker to improve the hydrophobicity of NCC. The reaction mechanism of NCC with KH560 and DTMOS and its surface chemical characteristics were investigated using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and HCl–acetone titration. These analyses confirmed that KH560 was grafted onto the surface of NCC through the ring-opening reaction, before DTMOS was covalently grafted onto the surface of NCC using KH560 as a linker. The grafting of NCC with DTMOS resulted in an improvement in its hydrophobicity due to an increase in its water contact angle from 0° to about 140°. In addition, the modified NCC also possessed enhanced thermal stability.

Modifying the Contact Angle of Anisotropic Cellulose Nanocrystals: Effect on Interfacial Rheology and Structure

Cellulose nanocrystals (CNCs) are an emerging natural material with the ability to stabilize fluid/fluid interfaces. Native CNC is hydrophilic and does not change the interfacial tension of the stabilized emulsion or foam system. In this study, rodlike cellulose particles were isolated from hemp and chemically modified to alter their hydrophobicity, i.e., their surface activity, which was demonstrated by surface tension measurements of the particles at the air/water interface. The buildup and mechanical strength of the interfacial structure were investigated using interfacial shear and dilatational rheometry. In contrast to most particle or protein-based interfacial adsorption layers, we observe in shear flow a Maxwellian behavior instead of a glasslike frequency response. The slow and reversible buildup of the layer and its unique frequency dependence indicate a weakly aggregated system, which depends on the hydrophobicity and, thus, on the contact angle of the CNC particles at the air/water interface. Exposed to dilatational flow, the weakly aggregated particles cluster and form compact structures. The interfacial structure generated by the different flow fields is characterized by the contact angle, immersion depth, and layer roughness obtained by neutron reflectometry with contrast variation while the size and local structural arrangement of the CNC particles were investigated by AFM imaging.

Cell interactions and cytotoxic studies of cellulose nanofibers from Curauá natural fibers

Cellulose nanofibers (CNF) were isolated from Curauá fibers (Ananas erectifolius L. B. Smith) through a mechanical grinder preceded by mild chemical treatment. Morphology and surface characteristics of the fibers were followed until it reaches the nanoscale as long and flexible nanofibers. In aqueous suspensions, SAXS techniques revealed that such nanofibers present a twisted ribbon structure while rheological measurements demonstrate its high viscosity and a thixotropic behavior. These characteristics suggests the potential application of CNF in biomedical field, which, in turn, stimulates the toxicological studies of such materials. The obtained materials do not show any sign of cytotoxicity by direct or indirect assays for cell viability and cell morphology using Vero cells. Moreover, during the adhesion test, the cells demonstrated higher affinity to the CNF surface. It can be related to its surface properties and its obtaining conditions, which did not use any hazardous chemicals.

Improving cellulose nanofibrillation of waste wheat straw using the combined methods of prewashing, p-toluenesulfonic acid hydrolysis, disk grinding, and endoglucanase post-treatment

Here we established a new approach for improving the cellulose nanofibrillation of high ash content waste wheat straw (WWS). The results were comprehensively elucidated from the ash removal, delignification, mechanical fibrillation and endoglucanase post-treatment. When water dosage was increased from 50 to 500 times of the WWS weight, the ash content gradually decreased during prewashing process, which facilitated lignin solubilization in subsequent p-toluenesulfonic acid (p-TsOH) hydrolysis. Approximately 80% of lignin in prewashed WWS could be dissolved during acid hydrolysis to result in a relatively higher crystallinity of 59.1%. Compared with the lignocellulosic nanofibrils (LCNF) directly obtained using acid hydrolysis and disk grinding, prewashing-assisted acid hydrolyzed WWS was fibrillated into LCNF with smaller height of 57.0 nm. Mild endoglucanase post-treatment could further produce less entangled LCNF with thinner diameters. In short, this study presented a promising and green pathway to achieve an efficient utilization of agricultural residue wastes to cellulose nanomaterials.

Cellulose nanomaterials as green nanoreinforcements for polymer nanocomposites

Unexpected and attractive properties can be observed when decreasing the size of a material down to the nanoscale. Cellulose is no exception to the rule. In addition, the highly reactive surface of cellulose resulting from the high density of hydroxyl groups is exacerbated at this scale. Different forms of cellulose nanomaterials, resulting from a top-down deconstruction strategy (cellulose nanocrystals, cellulose nanofibrils) or bottom-up strategy (bacterial cellulose), are potentially useful for a large number of industrial applications. These include the paper and cardboard industry, use as reinforcing filler in polymer nanocomposites, the basis for low-density foams, additives in adhesives and paints, as well as a wide variety of filtration, electronic, food, hygiene, cosmetic and medical products. This paper focuses on the use of cellulose nanomaterials as a filler for the preparation of polymer nanocomposites. Impressive mechanical properties can be obtained for these materials. They obviously depend on the type of nanomaterial used, but the crucial point is the processing technique. The emphasis is on the melt processing of such nanocomposite materials, which has not yet been properly resolved and remains a challenge.This article is part of a discussion meeting issue 'New horizons for cellulose nanotechnology'.

A new strategy to elaborate polymer composites via Pickering emulsion polymerization of a wide range of monomers

We report a novel strategy to prepare polymer composites reinforced with cellulose nanocrystals (CNCs) via Pickering emulsion polymerization.

RAFT-mediated Pickering emulsion polymerization with cellulose nanocrystals grafted with random copolymer as stabilizer

The synthesis of a RAFT-mediated Pickering emulsion was firstly achieved by using cellulose nanocrystals (CNCs) grafted with a random copolymer as the stabilizer. Firstly, poly(acrylonitrile-r-butyl acrylate) (poly(AN-r-nBA)) was synthesized by Cu(0)-mediated CRP, which was further modified via a click chemistry strategy to obtain poly(ethylene tetrazole-r-butyl acrylate) (poly(VT-r-nBA)). Then, poly(VT-r-nBA) was grafted onto the CNCs through a Mitsunobu reaction to obtain poly(VT-r-nBA)-g-CNCs. Stabilized by poly(VT-r-nBA)-g-CNCs, an O/W RAFT-mediated Pickering emulsion was formed for the preparation of well-controlled poly(methyl methacrylate) (PMMA) particles with water-soluble potassium persulfate (KPS) as an initiator and oil-soluble 4-cyanopentanoic acid dithiobenzoate (CPADB) as a chain transfer agent. Rheological analysis suggested that the prepared Pickering emulsion possessed good stability under the influences of changes in strain, time, frequency and temperature. Furthermore, the recycling and further utilization of the poly(VT-r-nBA)-g-CNCs could be simply realized through centrifugal separation.

A RAFT-mediated Pickering emulsion with cellulose nanocrystals grafted with a random copolymer was used for the preparation of poly(methyl methacrylate) particles..

Trans crystallization behavior and strong reinforcement effect of cellulose nanocrystals on reinforced poly(butylene succinate) nanocomposites

Biodegradable poly(butylene succinate) (PBS) nanocomposites are polymerized via in situ polymerization of succinic acid (SA) with cellulose nanocrystal (CNC)-loaded 1,4-butanediol (1,4-BD) mixtures.

Cellulose nanocrystal (CNC)–inorganic hybrid systems: synthesis, properties and applications

Cellulose nanocrystal (CNC), a class of sustainable nanomaterial derived from forest and agro-biomass can serve as nature's storage for carbon dioxide.

Examining the Use of Nanocellulose Composites for the Sorption of Contaminants of Emerging Concern: An Experimental and Computational Study

The occurrence of contaminants of emerging concern (CECs) in water is an environmental issue that must be addressed to avoid damage to ecosystems and human health. Inspired by this current issue, in this work, we fabricated nanocellulose (NC) particles grafted with the block copolymer Jeffamine ED 600 (NC-Jeffamine) capable of adsorbing acetaminophen, sulfamethoxazole, and N,N-diethyl-meta-toluamide (DEET) from aqueous solution by electrostatic interactions. NC-Jeffamine composites were prepared by carboxylation of the NC surface via 2,2,6,6-tetramethyl-1-piperidinyloxy oxidation followed by the covalent attachment of Jeffamine using the N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide/N-hydroxysulfosuccinimide sodium salt reaction. The reaction was followed and confirmed by Fourier transform infrared and conductometric titration. The physical characterization was performed by thermogravimetric analysis, Brunauer-Emmett-Teller analysis, scanning electron microscopy, dynamic light scattering, and Z-potential analysis. This material was used to study the adsorption profile of three CECs in deionized water, namely, acetaminophen, sulfamethoxazole, and DEET. The adsorption isotherms were obtained at pH 3, 7, and 9, where the best adsorption results corresponded to pH 9 because of the uniform dispersion of the adsorbate in solution. A computational study based on the density functional theory determined that the possible interactions of the CECs with the adsorbent material were related to hydrogen bonds and/or van der Waals forces. The calculated binding energies were used as a descriptor to characterize the optimum adsorption site of CECs onto NC-Jeffamine.

Post-sulfonation of cellulose nanofibrils with a one-step reaction to improve dispersibility

Cellulose nanofibrils (CNF) were sulfonated and the dispersion quality was compared to unfunctionalized and 2,2,6,6-tetramethylpiperdine-1-oxyl radical (TEMPO) post-oxidation treatment of existing CNF (mechanically fibrillated pulp). A post-sulfonation treatment on existing CNF in chlorosulfonic acid and dimethylformamide (DMF) resulted in sulfonated CNF that retained a fibril-like morphology. There was a small decrease in the cellulose crystallinity index for the sulfonated CNF, but this was much lower than the reported regioselective oxidative bisulfite pretreatment method used to make sulfonated CNF. The current approach was extremely quick, and 5min of reaction time was sufficient to result in significant improvements in dispersibility compared to unfunctionalized CNF. The sulfonated CNF and TEMPO oxidized CNF had better dispersibility compared to the unfunctionalized CNF when dispersed in DMF and water, and in many cases the sulfonated CNF had better dispersibility than the TEMPO CNF. It was found that when CNF was dispersed in DMF the TEMPO CNF formed carboxyl dimethylammonium groups, while the sulfonated CNF formed formate groups.

A new method to produce cellulose nanofibrils from microalgae and the measurement of their mechanical strength

Despite the enormous potential of cellulose nanofibrils (CNFs) as a reinforcing filler in various fields, the use of them has been limited by high-energy mechanical treatments that require a lot of energy and time consumption. To reduce the demands of energy and time required for mechanical treatments, microalgae, in particular, Nannochloropsis oceanica, which has small size, rapid growth rate, and high productivity was used as a CNFs source. This study obtains the CNFs by lipid/protein extraction, purification, and TEMPO-mediated oxidation processes under gentle mixing without high-energy mechanical treatments. Furthermore, to evaluate the applicability of microalgal CNFs as a reinforcing filler, this study estimated the mechanical strength of the fibrils by the sonication-induced scission method. To achieve a precise estimation, an effective method to distinguish straight fibrils from buckled fibrils was also developed, and subsequently, only straight fibrils were used to calculate the mechanical strength in the sonication-induced scission method. Consequently, the tensile strength of the N. oceanica CNFs is around 3-4GPa on average which is comparable with the mechanical strength of general reinforcing fillers and even higher than that of wood CNFs. Thus, this study has shown that the newly proposed simplified method using N. oceanica is very successful in producing CNFs with great mechanical strength which could be used in various reinforcement fields.