Quantum dot-induced phase stabilization of α-CsPbI3 perovskite for high-efficiency photovoltaics

Near-Infrared Photoluminescence from Ytterbium- and Erbium-Codoped CsPbCl3 Perovskite Quantum Dots with Negative Thermal Quenching

Near-infrared (NIR) luminescent phosphors hold promise for a wide range of applications, from bioimaging to light-emitting diodes (LEDs), but are typically confined to wavelengths <1300 nm and manifest substantial thermal quenching pervasive in luminescent materials. Here we observed the thermally enhanced NIR luminescence of Er³⁺ (1540 nm), a 2.5-fold enhancement with increasing temperature from 298 to 356 K, from Yb³⁺- and Er³⁺-codoped CsPbCl₃ perovskite quantum dots (PQDs) (photoexcited at ∼365 nm). Mechanistic investigations revealed that thermally enhanced phenomena originated from combined effects of thermally stable cascade energy transfer (from a photoexcited exciton to a pair of Yb³⁺ and then to surrounding Er³⁺) and minimized quenching of surface-adsorbed water molecules on the ⁴I_13/2 state of Er³⁺ induced by the temperature increase. Importantly, these PQDs enable producing phosphor-converted LEDs emitting at 1540 nm with inherited thermally enhanced properties, having implications for a wide range of photonic applications.

Structural effects on the luminescence properties of CsPbI3 nanocrystals

Metal halide perovskite nanocrystals (NCs) are promising for photovoltaic and light-emitting applications. Due to the softness of their crystal lattice, structural modifications have a critical impact on their optoelectronic properties. Here we investigate the size-dependent optoelectronic properties of CsPbI3 NCs ranging from 7 to 17 nm, employing temperature and pressure as thermodynamic variables to modulate the energetics of the system and selectively tune the interatomic distances. By temperature-dependent photoluminescence spectroscopy, we have found that luminescence quenching channels exhibit increased non-radiative losses and weaker exciton-phonon coupling in bigger particles, in turn affecting the luminescence efficiency. Through pressure-dependent measurements up to 2.5 GPa, supported by XRD characterization, we revealed a NC-size dependent solid-solid phase transition from the γ-phase to the δ-phase. Importantly, the optical response to these structural changes strongly depends on the size of the NC. Our findings provide an interesting guideline to correlate the size and structural and optoelectronic properties of CsPbI3 NCs, important for engineering the functionalities of this class of soft semiconductors.

Influence of Sr doping on the photoelectronic properties of CsPbX3 (X = Cl, Br, or I): a DFT investigation

To broaden the application of cesium lead halide perovskites, doping technology has been widely proposed. In this study, we calculated a 12.5% concentration of a Sr-doped CsPbX₃ (X = Cl, Br, or I) perovskite via density functional theory. The results showed that the bandgap energy of the perovskite increased by 0.2-0.3 eV. The high symmetry points of the energy band changed from R to Γ after Sr doping because the Sr doping affected the initial distribution of atomic orbital hybridization. In addition, optical absorption spectra after doping showed an obvious blueshift, whereas the absorption coefficient of CsPb_0.875Sr_0.125X₃ had the same magnitude as undoped CsPbX₃. Moreover, the effective masses of electrons and holes changed within a small range (0.01-0.03 m₀) after Sr doping. According to the findings of this study, the CsPb_0.875Sr_0.125X₃ perovskite is expected to become an ideal candidate material for designing photovoltaic and photoelectric devices.

Challenges and developments for the blue perovskite nanocrystal light-emitting diodes

Perovskite nanomaterials have been highly thought as next-generation light emitters after recent development owing to their benefits of simple synthesis, low-cost, large-area, and wide color gamut. Encouragingly, the external quantum efficiencies (EQEs) of green, red, and near-infrared perovskite light-emitting diodes (PeLEDs) have exceeded more than 20%. However, the performance of the blue PeLEDs is still lower than other analogs, which severely limits the applications of PeLEDs in future full-color displays. Herein, we have reviewed the advances in blue perovskite NCs and their applications in blue PeLEDs. Promising blue perovskite emitters and strategies for fabricating highly efficient blue PeLEDs based on perovskite NCs are investigated and highlighted. Moreover, we point out the main challenges in blue perovskite NC LEDs including low electroluminescence efficiency (EL), spectral instability, the difficulty of charge injection, and device optimization. The perspectives for the further development of blue PeLEDs are also presented.

Efficient Charge-Transfer Studies for Selective Detection of Bilirubin Biomolecules Using CsPbBr3 as the Fluorescent Probe

Bright luminescence hybrid halide perovskite nanocrystals (PNCs) as a novel fluorophore class have not been broadly explored in biological sensing. Herein, we synthesized highly fluorescent CsPbBr₃ PNCs through the LARP method using oleic acid and oleyl amine as capping ligands. Morphological and optical properties of as-synthesized PNCs were studied using transmission electron microscopy, X-ray diffraction, UV-vis, and emission spectroscopic analysis. Oleic acid- and oleyl amine-capped PNCs are employed for sensitive and selective detection of bilirubin (BR). A panel of characterizations (time-correlated single-photon count spectroscopy and photoluminescence (PL)) was carried out to investigate the detailed sensing study of PNCs-BR composite for quenching the PL emission of CsPbBr₃ with BR. It has been noticed that the synthesized nanoparticles are highly capable of detecting BR and thus act as a biological material sensor.

Perspectives for the conversion of perovskite indoor photovoltaics into IoT reality

As a competitive candidate for powering low-power terminals in Internet of Things (IoT) systems, indoor photovoltaic (IPV) technology has attracted much attention due to its effective power output under indoor light illumination. One such emerging photovoltaic technology, perovskite cell, has become a hot topic in the field of IPVs due to its outstanding theoretical performance limits and low manufacturing costs. However, several elusive issues remain limiting their applications. In this review, the challenges for perovskite IPVs are discussed in view of the bandgap tailoring to match indoor light spectra and the defect trapping regulation throughout the devices. Then, we summarize up-to-date perovskite cells, highlighting advanced strategies such as bandgap engineering, film engineering and interface engineering to enhance indoor performance. The investigation of indoor applications of large and flexible perovskite cells and integrated devices powered by perovskite cells is exhibited. Finally, the perspectives for the perovskite IPV field are provided to help facilitate the further improvement of indoor performance.

Precise modulation strategies of 2D/3D perovskite heterojunctions in efficient and stable solar cells

2D/3D perovskite heterojunctions exhibit promising prospects in the improvement of efficiency and stability of perovskite solar cells (PSCs). However, many challenges remain in the development of high-quality 2D/3D heterojunctions, such as a reliable pathway to control the perovskite phase and generally poor performance in inverted (p-i-n) devices, which limit their commercialization. Fortunately, many excellent works have proposed lots of strategies to solve these challenges, which have triggered a new wave of research on 2D/3D perovskite heterojunctions in recent years. In this paper, the latest research progress and the critical factors involved in the modulating mechanisms of PSCs with 2D/3D heterojunctions have been summarized and laid out systematically. The advantages of constructing 2D/3D perovskite heterojunctions in PSCs are highlighted, and the problems and related solutions of low-dimensional perovskites as passivation layers towards high-performance PSCs are also discussed in depth. Finally, the prospects of 2D/3D perovskite heterojunctions utilized in the passivation strategies to further improve the photovoltaic performance of PSCs in the future have been presented.

Electron Trapping Prolongs the Lifetime of Charge-Separated States in 2D Perovskite Nanoplatelet-Hole Acceptor Complexes

Two-dimensional (2D) lead halide perovskite nanoplatelets (NPLs) are promising materials for blue light emission because of the strong quantum confinement in the 2D morphology. However, the identity of carrier traps and the trap influence on charge transfer in these NPLs remain unclear. Herein, transient absorption studies revealed two types of electron traps in 3 monolayer lead bromide perovskite NPLs with trapping lifetime of 9.0 ± 0.6 and 516 ± 59 ps, respectively, while no hole traps were observed. Systematic charge transfer experiments show that electron traps have negligible influence on ultrafast electron transfer or hole transfer but extend the half-lifetime of the charge-separated state from 2.1 ± 0.1 to 68 ± 3 ns after hole transfer, which is explained by the reduced electron-hole overlap. This work contributes to the understanding of the fundamental carrier dynamics in 2D perovskite NPLs and offers guidelines for boosting their performance in optoelectronics and photocatalysis.

Direct Observation of Transient Structural Dynamics of Atomically Thin Halide Perovskite Nanowires

Halide perovskite is a unique dynamical system, whose structural and chemical processes happening across different timescales have significant impact on its physical properties and device-level performance. However, due to its intrinsic instability, real-time investigation of the structure dynamics of halide perovskite is challenging, which hinders the systematic understanding of the chemical processes in the synthesis, phase transition, and degradation of halide perovskite. Here, we show that atomically thin carbon materials can stabilize ultrathin halide perovskite nanostructures against otherwise detrimental conditions. Moreover, the protective carbon shells enable atomic-level visualization of the vibrational, rotational, and translational movement of halide perovskite unit cells. Albeit atomically thin, protected halide perovskite nanostructures can maintain their structural integrity up to an electron dose rate of 10,000 e^-/Ų·s while exhibiting unusual dynamical behaviors pertaining to the lattice anharmonicity and nanoscale confinement. Our work demonstrates an effective method to protect beam-sensitive materials during in situ observation, unlocking new solutions to study new modes of structure dynamics of nanomaterials.

Ligands in Lead Halide Perovskite Nanocrystals: From Synthesis to Optoelectronic Applications

Ligands are indispensable for perovskite nanocrystals (NCs) throughout the whole lifetime, as they not only play key roles in the controllable synthesis of NCs with different sizes and shapes, but also act as capping shell that affects optical properties and electrical coupling of NCs. Establishing a systematic understanding of the relationship between ligands and perovskite NCs is significant to enable many potential applications of NCs. This review mainly focuses on the influence of ligands on perovskite NCs. First of all, the ligands-dominated size and shape control of NCs is discussed. Whereafter, the surface defects of NCs and the bonding between ligands and perovskite NCs are classified, and corresponding post-treatment of surface defects via ligands is also summarized. Furthermore, advances in engineering the ligands towards the high performance of optoelectronic devices based on perovskite NCs, including photodetector, solar cell, light emitting diode (LED), and laser, and finally to potential challenges are also discussed.

A Reconfigurable Optoelectronic Synaptic Transistor with Stable Zr-CsPbI3 Nanocrystals for Visuomorphic Computing

Reconfigurable phototransistor memory attracts considerable attention for adaptive visuomorphic computing, with highly efficient sensing, memory, and processing functions integrated onto a single device. However, developing reconfigurable phototransistor memory remains a challenge due to the lack of an all-optically controlled transition between short-term plasticity (STP) and long-term plasticity (LTP). Herein, an air-stable Zr-CsPbI₃ perovskite nanocrystal (PNC)-based phototransistor memory is designed, which is capable of broadband photoresponses. Benefitting from the different electron capture ability of Zr-CsPbI₃ PNCs to 650 and 405 nm light, an artificial synapse and non-volatile memory can be created on-demand and quickly reconfigured within a single device for specific purposes. Owing to the optically reconfigurable and wavelength-aware operation between STP and LTP modes, the integrated blue feature extraction and target recognition can be demonstrated in a homogeneous neuromorphic vision sensor array. This work suggests a new way in developing perovskite optoelectronic transistors for highly efficient in-sensor computing.

Open-circuit voltage loss in perovskite quantum dot solar cells

Perovskite quantum dots are a competitive candidate for next-generation solar cells owing to their superior phase stability and multiple exciton generation effects. However, given the voltage loss in perovskite quantum dot solar cells (PQDSCs) is mainly caused by various surface and interfacial defects and the energy band mismatch in the devices, tremendous achievements have been made to mitigate the V_oc loss of PQDSCs. Herein, we elucidate the potential threats that hinder the high V_oc of PQDSCs. Then, we summarize recent progress in minimizing open-circuit voltage (V_oc) loss, including defect manipulation and device optimization, based on band-alignment engineering. Finally, we attempt to shed light on the methodologies used to further improve the performance of PQDSCs.

Exploring the Role of Short Chain Acids as Surface Ligands in Photoinduced Charge Transfer Dynamics from CsPbBr3 Perovskite Nanocrystals

The most commonly used surface capping ligands, like oleic acid and oleylamine, passivate the surface of perovskite nanocrystals (PNCs) to enhance their stability and optical properties. However, due to their inherent insulating nature, charge transport across the surface of the PNCs is hindered, limiting their application in devices. In this study, we have post-treatment CsPbBr₃ PNCs with short chain ligands benzoic acid (BA) and ascorbic acid (AA) and observed that both acid-treated PNCs show enhanced stability and optical properties. Still, BA-treated PNCs show the highest charge transport rate due to their conjugating nature. The photoelectrochemical measurements also show the most efficient electron flow across the surface of the PNC with BA-treated PNCs. A longer carrier lifetime and fast charge transfer make BA-treated PNCs ideal candidates for application in real-life devices.

Combining π-Conjugation and Cation-π Interaction for Water-Stable and Photoconductive One-Dimensional Hybrid Lead Bromide

Hybrid lead halide perovskites and their derivatives are important optoelectronic materials but suffer from water instability. Combining both the optoelectronics and the water stability of such systems is a major challenge in material design today. To address this issue, we employ the well-known π-conjugation and cation-π interaction concepts in designing a hybrid lead halide perovskite derivative system. (4,4'-VDP)Pb₂Br₆ (VDP = vinylenedipyridinium) single crystals are prepared. They have a one-dimensional (1D) arrangement of inorganic Pb-Br sublattices connected via the 4,4'-VDP organic sublattice. The π-conjugation in the 4,4'-VDP sublattice allows electronic communication between the 1D Pb-Br units, reducing the band gap and improving the photoconductivity. Importantly, N⁺ of one 4,4'-VDP molecular ion interacts with the π-electron cloud of the adjacent one. This intermolecular cation-π interaction extends throughout the organic sublattice, making the hybrid crystal stable when stored under water for more than a year without requiring any encapsulations.

Directional Amplified Photoluminescence through Large-Area Perovskite-Based Metasurfaces

Perovskite nanocrystals are high-performance, solution-processed materials with a high photoluminescence quantum yield. Due to these exceptional properties, perovskites can serve as building blocks for metasurfaces and are of broad interest for photonic applications. Here, we use a simple grating configuration to direct and amplify the perovskite nanocrystals' original omnidirectional emission. Thus far, controlling these radiation properties was only possible over small areas and at a high expense, including the risks of material degradation. Using a soft lithographic printing process, we can now reliably structure perovskite nanocrystals from the organic solution into light-emitting metasurfaces with high contrast on a large area. We demonstrate the 13-fold amplified directional radiation with an angle-resolved Fourier spectroscopy, which is the highest observed amplification factor for the perovskite-based metasurfaces. Our self-assembly process allows for scalable fabrication of gratings with predefined periodicities and tunable optical properties. We further show the influence of solution concentration on structural geometry. By increasing the perovskite concentration 10-fold, we can produce waveguide structures with a grating coupler in one printing process. We analyze our approach with numerical modeling, considering the physiochemical properties to obtain the desired geometry. This strategy makes the tunable radiative properties of such perovskite-based metasurfaces usable for nonlinear light-emitting devices and directional light sources.

Interfacial passivation of CsPbI3 quantum dots improves the performance of hole-transport-layer-free perovskite photodetectors

Photodetectors (PDs) suffer from dark current due to defects in the perovskite photosensitive layer. Contact between the photosensitive layer and carbon electrodes could result in recombination of carriers at the interface. In this work, CsPbI₃ quantum dots (QDs) were added between the photosensitive layer and the carbon electrode as the interfacial layer to passivate the surface defects of perovskite layer and improve the energy level matching at the interface. The effect of QDs concentrations on the passivation of the perovskite layer was investigated. It was found that the photoluminescence intensity of perovskite films was the strongest and the decay lifetime was the longest when the QDs concentration was 3 mg/mL. Owing to QDs passivation, the dark current of perovskite PD decreased by 94% from [Formula: see text] to [Formula: see text] A. The responsivity (R) at 605 nm improved by 27% from 0.29 to 0.37 A/W at 0 V bias voltage. The specific detectivity (D*) increased by 420% from [Formula: see text] to [Formula: see text] Jones.

Fabrication of High-Quality CsPbI3 Perovskite Films with Phosphorus Pentachloride Additive for Highly Stable Solar Cells

Fully inorganic perovskite cesium lead triiodide (CsPbI₃ ) has garnered much attention from researcher for photovoltaic application because of its excellent thermal stability compared with the inorganic-organic hybrid counterparts, along with the potential to serve as the top cell in tandem devices with silicon solar cell. However, the active α-phase cubic CsPbI₃ spontaneously tends to transform into the non-perovskite δ-CsPbI₃ when subjected to ambient condition. This work proposes an effective method to fabricate high-quality and stable α-phase cubic CsPbI₃ films by introducing phosphorus pentachloride (PCl₅ ) as an additive. PCl₅ acts as colloidal binder for modulating crystallization dynamics of perovskites, resulting in high-quality film and a significantly suppressed phase transition. Finally, highly stable CsPbI₃ perovskite solar cells can be achieved with a power conversion efficiency up to 17.85 %, and a long-term stability in N₂ filled glove box.

Environment-friendly copper-based chalcogenide thin film solar cells: status and perspectives

Copper chalcogenides (CuCh) have attracted considerable attention due to their promising potential as environmental-friendly photoactive material for lightweight and flexible thin film solar cells. Further, CuCh can be fabricated from simple to complex chemical compositions and offer a remarkable charge carrier mobility and excellent absorption coefficient with a desirable bandgap (up to ∼1.0 eV). Currently, they have demonstrated maximum power conversion efficiencies of over 23% for single-junction, around 25% and 28% for monolithic 2-Terminal (2T) and mechanically-stacked 4-Terminal (4T) perovskite/CuCh tandem solar cells, respectively. This article presents an overview of CuCh-based materials, from binary- to quaternary-CuCh compounds for single- and multi-junction solar cells. Then, we discuss the development of fabrication methods and the approaches taken to improve the performance of CuCh-based thin film itself, including chemical doping, the development of complement layers, and their potential application in flexible and lightweight devices. Finally, these technologies' stability, scalability, and toxicity aspects are discussed to enhance their current marketability.

A Universal Perovskite Nanocrystal Ink for High-Performance Optoelectronic Devices

Semiconducting lead halide perovskite nanocrystals (PNCs) are regarded as promising candidates for next-generation optoelectronic devices due to their solution processability and outstanding optoelectronic properties. While the field of light-emitting diodes (LEDs) and photovoltaics (PVs), two prime examples of optoelectronic devices, has recently seen a multitude of efforts toward high-performance PNC-based devices, realizing both devices with high efficiencies and stabilities through a single PNC processing strategy has remained a challenge.  In this work, diphenylpropylammonium (DPAI) surface ligands, found through a judicious ab-initio-based ligand search, are shown to provide a solution to this problem. The universal PNC ink with DPAI ligands presented here, prepared through a solution-phase ligand-exchange process, simultaneously allows single-step processed LED and PV devices with peak electroluminescence external quantum efficiency of 17.00% and power conversion efficiency of 14.92% (stabilized output 14.00%), respectively. It is revealed that a careful design of the aromatic rings such as in DPAI is the decisive factor in bestowing such high performances, ease of solution processing, and improved phase stability up to 120 days. This work illustrates the power of ligand design in producing PNC ink formulations for high-throughput production of optoelectronic devices; it also paves a path for "dual-mode" devices with both PV and LED functionalities.

Dimethyl sulfoxide: a promising solvent for inorganic CsPbI3 perovskite

Inorganic CsPbI₃ perovskite is an important photovoltaic material due to its suitable band gap and high chemical stability. However, it is a challenge to grow high-quality CsPbI₃ perovskite because the stability of perovskite phase is low and is sensitive to solvent. So far, most of CsPbI₃ perovskites in high-performance perovskite solar cells (PSCs) were prepared from N,N-dimethylformamide, a highly toxic solvent, and no successful case has been reported for dimethyl sulfoxide (DMSO), which is environmentally-friendly with considerably higher complexation capability. Herein, we reveal that forming DMSO-based adduct is the main cause for limiting the quality of CsPbI₃ perovskite from DMSO-based solutions, which would inhibit the formation of DMAPbI₃ (DMA = dimethylammonium, (CH₃)₂NH₂⁺) intermediate. Then, by introducing a vacuum treatment, DMSO molecules could be efficiently extracted from the adduct to induce the formation of DMAPbI₃ intermediate. After annealing, the intermediate is transitioned to the CsPbI₃ perovskite with enhanced crystallinity, high orientation, low defect density, and high uniformity. By using the CsPbI₃ perovskite as a light absorber, the PSCs based on carbon electrode (C-PSCs) achieve an efficiency of 16.7%, a new record for inorganic C-PSCs.

Interplay of Purcell effect and extraction efficiency in CsPbBr3 quantum dots coupled to Mie resonators

Inorganic halide perovskite quantum dots have risen in recent years as efficient active materials in numerous optoelectronic applications ranging from solar cells to light-emitting diodes and lasers, and have lately been tested as quantum emitters. Perovskite quantum dots are often coupled to photonic structures either to enhance their emission properties, by accelerating their emission rate thanks to the Purcell effect, or to increase light extraction. From a theoretical point of view, the first effect is often considered at the single-dipole level while the latter is often treated at the mesoscopic level, except possibly for quantum emitters. In this work we employ a layer of perovskite quantum dots coupled to dielectric Mie resonators to exploit both effects simultaneously and achieve an 18-fold increase in luminescence. Our numerical simulations, combined with spatially- and time-resolved photoluminescence measurements, reveal how the macroscopic response of the perovskite-on-Mie resonator structure results from the interplay of the two effects averaged over the whole spatial distribution of emitters. Our work provides thus guiding principles for maximizing the output intensity of quantum emitters embedded into photonic resonators as well as classical emitters integrated in perovskite-based optoelectronic devices.

Ultrasound-activated luminescence with color tunability enabled by mechanoluminescent colloids and perovskite quantum dots

Ultrasound represents a wireless and non-contact route for energy delivery and device control, owing to its ability to propagate and focus in various mediums including biological tissue. Specifically, ultrasound-activated mechanoluminescence from a colloidal suspension of mechanoluminescent (ML) nanocrystals offers a wireless means to remotely control a light source, such as wirelessly addressing a multicolor display. However, the limited color purity and tunability, as well as the large sizes of conventional ML materials prevent their use in an ultrasound-mediated flexible color display. Here, we apply a biomineral-inspired suppressed dissolution approach to synthesize ML colloids with bright blue emission under ultrasound and small sizes down to 20 nm. In addition, we leverage the bandgap engineering strategy of all-inorganic perovskite quantum dots (PQDs) to achieve wavelength tunability of the mechanoluminescence of ML colloid/PQD composites. Remarkably, the ultrasound-activated emission of the ML colloid/PQD composites exhibits a highly saturated color gamut covering the entire visible spectrum. Based on these advantages, we assembled a pixel array composed of different ML colloid/PQD composites in a silicone elastomer and demonstrated the proof-of-concept of a flexible and wireless multicolor display with each pixel individually addressed by scanning focused ultrasound.

Tiny spots to light the future: advances in synthesis, properties, and application of perovskite nanocrystals in solar cells

Perovskites are in the hotspot of material science and technology. Outstanding properties have been discovered, fundamental mechanisms of defect formation and degradation elucidated, and applications in a wide variety of optoelectronic devices demonstrated. Advances through adjusting the bulk-perovskite composition, as well as the integration of layered and nanostructured perovskites in the devices, allowed improvement in performance and stability. Recently, efforts have been devoted to investigating the effects of quantum confinement in perovskite nanocrystals (PNCs) aiming to fabricate optoelectronic devices based solely on these nanoparticles. In general, the applications are focused on light-emitting diodes, especially because of the high color purity and high fluorescence quantum yield obtained in PNCs. Likewise, they present important characteristics featured for photovoltaic applications, highlighting the possibility of stabilizing photoactive phases that are unstable in their bulk analog, the fine control of the bandgap through size change, low defect density, and compatibility with large-scale deposition techniques. Despite the progress made in the last years towards the improvement in the performance and stability of PNCs-based solar cells, their efficiency is still much lower than that obtained with bulk perovskite, and discussions about upscaling of this technology are scarce. In light of this, we address in this review recent routes towards efficiency improvement and the up-scaling of PNC solar cells, emphasizing synthesis management and strategies for solar cell fabrication.

Highly stable lanthanide-doped CsPbI3 perovskite nanocrystals with near-unity quantum yield for efficient red light-emitting diodes

CsPbI₃ perovskite nanocrystals (NCs) are gaining popularity as promising photoactive materials for optoelectronic devices. However, their poor phase stability has caused substantial limitations in their practical application. Herein, the small-sized rare earth La cation is strategically introduced to fundamentally improve the NC phase stability against the environment, heat, and UV radiation by the partial substitution of Pb ions to suppress structural distortion and increase the formation energy. The strong interaction between La and I of the octahedra has been demonstrated to enable the effective suppression of the trap states, which promotes strengthened radiative recombination for a near-unity photoluminescence quantum yield (PLQY) of 99.3%. High energy bands have also been found for the La-doped NCs to narrow down the energy barrier for efficient hole injection. The superior optoelectronic properties of La-doped NCs promote great improvements in the perovskite light-emitting diode (PeLED) performances with a 5-fold improvement in external quantum efficiency (EQE) from 1.19 to 6.01% and 2-fold longer lifetime from 1451 to 2956 s. This work provides an effective method for small-sized metal ion-doped CsPbI₃ NCs to realize high emission efficiency and phase stabilization for efficient PeLEDs.

Large-area waterproof and durable perovskite luminescent textiles

Lead halide perovskites show great potential to be used in wearable optoelectronics. However, obstacles for real applications lie in their instability under light, moisture and temperature stress, noxious lead ions leakage and difficulties in fabricating uniform luminescent textiles at large scale and high production rates. Overcoming these obstacles, we report simple, high-throughput electrospinning of large-area (> 375 cm²) flexible perovskite luminescent textiles woven by ultra-stable polymer@perovskite@cyclodextrin@silane composite fibers. These textiles exhibit bright and narrow-band photoluminescence (a photoluminescence quantum yield of 49.7%, full-width at half-maximum <17 nm) and the time to reach 50% photoluminescence of 14,193 h under ambient conditions, showcasing good stability against water immersion (> 3300 h), ultraviolet irradiation, high temperatures (up to 250 °C) and pressure surge (up to 30 MPa). The waterproof PLTs withstood fierce water scouring without any detectable leaching of lead ions. These low-cost and scalable woven PLTs enable breakthrough application in marine rescue.

Synthesis and Applications of Halide Perovskite Nanocrystals in Optoelectronics

The perovskites used for optoelectronic devices have been more attractive during recent years due to their wide variety of advantages, such as their low cost, high photoluminescence quantum yield (PLQY), high carrier mobility, flexible bandgap tunability, and high light absorption ability. However, optoelectronic applications for traditional inorganic and organic materials present dilemmas due to their hardly tunable bandgap and instability. On the other hand, there are some more important benefits for perovskite nanocrystals, such as a size-dependent bandgap and the availability of anion exchange at room temperature. Therefore, perovskite NC-based applications are currently favored, offering a research direction beyond perovskite, and much research has focused on the stability issue and device performance. Thus, the synthesis and applications of perovskite NCs need to be thoroughly discussed for the future development of solar cells, light-emitting diodes, photodetectors, and laser research.

A Low-Cost Synthetic Route of FAPbI3 Quantum Dots in Air at Atmospheric Pressure: The Role of Zinc Iodide Additives

Perovskite quantum dots (PQDs) have shown great promise in optoelectronic device applications. Typically, a traditional hot-injection method with heating and high vacuum pressure is used to synthesize these colloidal nanoparticles. In this article, we report a low-cost synthetic method for FAPbI₃ PQDs in air at atmospheric pressure with the assistance of ZnI₂. Compared with the FAPbI₃ PQDs synthesized under vacuum/N₂ condition, the air-synthesized Zn:FAPbI₃ PQDs exhibit the same crystalline structure with a similar preferential crystallographic orientation but demonstrate higher colloidal stability and higher production yield. Furthermore, we examine the influence of ZnI₂ during the synthesis process on morphologies and optoelectronic properties. The results show that the mean size of the obtained FAPbI₃ PQDs is decreased by increasing the amount of added ZnI₂. More importantly, introducing an optimal amount of ZnI₂ into the Pb source precursor enables increasing the carrier lifetime of FAPbI₃ PQDs, showing the potential beneficial effect on device performance.

Key Factors Affecting the Stability of CsPbI3 Perovskite Quantum Dot Solar Cells: A Comprehensive Review

The power conversion efficiency of CsPbI₃ perovskite quantum dot (PQD) solar cells shows increase from 10.77% to 16.2% in a short period owing to advances in material and device design for solar cells. However, the device stability of CsPbI₃ PQD solar cells remains poor in ambient conditions, which requires an in-depth understanding of the degradation mechanisms of CsPbI₃ PQDs solar cells in terms of both inherent material properties and device characteristics. Along with this analysis, advanced strategies to overcome poor device stability must be conceived. In this review, fundamental mechanisms that cause the degradation of CsPbI₃ PQD solar cells are discussed from the material property and device viewpoints. In addition, based on detailed insights into degradation mechanisms in CsPbI₃ PQD solar cells, various strategies are introduced to improve the stability of CsPbI₃ PQD solar cells. Finally, future perspectives and challenges are presented to achieve highly durable CsPbI₃ PQD solar cells. The investigation of the degradation mechanisms and the stability enhancement strategies can pave the way for the commercialization of CsPbI₃ PQD solar cells.

A Demulsification-Crystallization Model for High-Quality Perovskite Nanocrystals

A room-temperature technique with all-nonpolar-solvent, which circumvents the sensitivity of ionic perovskite to polar solvent, has become attractive for the synthesis of metal halide perovskite nanocrystals (PNCs). However, the lack of understanding of the inner mechanism, especially for the state of the precursor and the crystallization process of the PNCs, hinders further development of this technique. Here, through systematic study of the Pb precursor and in situ characterization of the PNCs, it is revealed that the reverse micelle nature of the Pb precursor exactly creates a novel demulsification-crystallization (D-C) model, namely, a two-stage nucleation is divided by a demulsification process for the PNCs. On this basis, a top efficiency for green light-emitting diodes based on PNCs is obtained with a maximum external quantum efficiency of 22.5% through tailoring the D-C model using a multiple-acid-anion synergistic assisted strategy to obtain high-quality PNCs. Beyond the high efficiency, the work paves the way for diverse ideas in PNC synthesis.

Hybrid Block Copolymer/Perovskite Heterointerfaces for Efficient Solar Cells

Solution processable semiconductors like organics and emerging lead halide perovskites (LHPs) are ideal candidates for photovoltaics combining high performance and flexibility with reduced manufacturing cost. Moreover, the study of hybrid semiconductors would lead to advanced structures and deep understanding that will propel this field even further. Herein, a novel device architecture involving block copolymer/perovskite hybrid bulk heterointerfaces is investigated, such a modification could enhance light absorption, create an energy level cascade, and provides a thin hydrophobic layer, thus enabling enhanced carrier generation, promoting energy transfer and preventing moisture invasion, respectively. The resulting hybrid block copolymer/perovskite solar cell exhibits a champion efficiency of 24.07% for 0.0725 cm² -sized devices and 21.44% for 1 cm² -sized devices, respectively, together with enhanced stability, which is among the highest reports of organic/perovskite hybrid devices. More importantly, this approach has been effectively extended to other LHPs with different chemical compositions like MAPbI₃ and CsPbI₃ , which may shed light on the design of highly efficient block copolymer/perovskite hybrid materials and architectures that would overcome current limitations for realistic application exploration.

Anion Doping Delays Nonradiative Electron-Hole Recombination in Cs-Based All-Inorganic Perovskites: Time Domain ab Initio Analysis

Using time-domain density functional theory combined with nonadiabatic (NA) molecular dynamics, we demonstrate that composition engineering of the X-site anions has a strong influence on the nonradiative electron-hole recombination and thermodynamic stability of cesium-based all-inorganic perovskites. Partial substitution of iodine(I) with bromine (Br) and acetate (Ac) anions reduces the NA electron-vibrational coupling by minimizing the overlap between the electron and hole wave functions and suppressing atomic fluctuations. The doping also widens the energy gap to further reduce the NA coupling and to enhance the open-circuit voltage of perovskite solar cells. These factors increase the charge carrier lifetime by an order of magnitude and improve structural stability in the series CsPbI_1.88BrAc_0.12 > CsPbI₂Br > CsPbI₃. The fundamental atomistic insights into the influence of anion doping on the photophysical properties of the all-inorganic lead halide perovskites guide the design of efficient optoelectronic materials.

An embedded interfacial network stabilizes inorganic CsPbI3 perovskite thin films

The black perovskite phase of CsPbI₃ is promising for optoelectronic applications; however, it is unstable under ambient conditions, transforming within minutes into an optically inactive yellow phase, a fact that has so far prevented its widespread adoption. Here we use coarse photolithography to embed a PbI₂-based interfacial microstructure into otherwise-unstable CsPbI₃ perovskite thin films and devices. Films fitted with a tessellating microgrid are rendered resistant to moisture-triggered decay and exhibit enhanced long-term stability of the black phase (beyond 2.5 years in a dry environment), due to increasing the phase transition energy barrier and limiting the spread of potential yellow phase formation to structurally isolated domains of the grid. This stabilizing effect is readily achieved at the device level, where unencapsulated CsPbI₃ perovskite photodetectors display ambient-stable operation. These findings provide insights into the nature of phase destabilization in emerging CsPbI₃ perovskite devices and demonstrate an effective stabilization procedure which is entirely orthogonal to existing approaches.

Effect of Various Electron and Hole Transport Layers on the Performance of CsPbI3-Based Perovskite Solar Cells: A Numerical Investigation in DFT, SCAPS-1D, and wxAMPS Frameworks

CsPbI₃ has recently received tremendous attention as a possible absorber of perovskite solar cells (PSCs). However, CsPbI₃-based PSCs have yet to achieve the high performance of the hybrid PSCs. In this work, we performed a density functional theory (DFT) study using the Cambridge Serial Total Energy Package (CASTEP) code for the cubic CsPbI₃ absorber to compare and evaluate its structural, electronic, and optical properties. The calculated electronic band gap (E _g) using the GGA-PBE approach of CASTEP was 1.483 eV for this CsPbI₃ absorber. Moreover, the computed density of states (DOS) exhibited the dominant contribution from the Pb-5d orbital, and most charges also accumulated for the Pb atom as seen from the electronic charge density map. Fermi surface calculation showed multiband character, and optical properties were computed to investigate the optical response of CsPbI₃. Furthermore, we used IGZO, SnO₂, WS₂, CeO₂, PCBM, TiO₂, ZnO, and C₆₀ as the electron transport layers (ETLs) and Cu₂O, CuSCN, CuSbS₂, Spiro-MeOTAD, V₂O₅, CBTS, CFTS, P3HT, PEDOT:PSS, NiO, CuO, and CuI as the hole transport layers (HTLs) to identify the best HTL/CsPbI₃/ETL combinations using the SCAPS-1D solar cell simulation software. Among 96 device structures, the best-optimized device structure, ITO/TiO₂/CsPbI₃/CBTS/Au, was identified, which exhibited an efficiency of 17.9%. The effect of the absorber and ETL thickness, series resistance, shunt resistance, and operating temperature was also evaluated for the six best devices along with their corresponding generation rate, recombination rate, capacitance-voltage, current density-voltage, and quantum efficiency characteristics. The obtained results from SCAPS-1D were also compared with wxAMPS simulation results.

The current state of the art in internal additive materials and quantum dots for improving efficiency and stability against humidity in perovskite solar cells

The remarkable optoelectronic capabilities of perovskite structures enable the achievement of astonishingly high-power conversion efficiencies on the laboratory scale. However, a critical bottleneck of perovskite solar cells is their sensitivity to the surrounding humid environment affecting drastically their long-term stability. Internal additive materials together with surface passivation, polymer-mixed perovskite, and quantum dots, have been investigated as possible strategies to enhance device stability even in unfavorable conditions. Quantum dots (QDs) in perovskite solar cells enable power conversion efficiencies to approach 20%, making such solar cells competitive to silicon-based ones. This mini-review summarized the role of such QDs in the perovskite layer, hole-transporting layer (HTL), and electron-transporting layer (ETL), demonstrating the continuous improvement of device efficiencies.

Bandlike Transport in FaPbBr3 Quantum Dot Phototransistor with High Hole Mobility and Ultrahigh Photodetectivity

Halide perovskites have been widely explored for numerous optoelectronic applications among which phototransistors have appeared as one of the most promising light signal detectors. However, it is still a great challenge to endow halide perovskites with both mobility and high photosensitivity because of their high sensitivity to moisture in ambient atmosphere. Here, we explore an FAPbBr₃ perovskite quantum dot (QD) phototransistor with bandlike charge transport and measure a dark hole mobility of 14.2 cm² V^-1 s^-1 at ambient atmosphere. Attaining both high mobility and good optical figures of merit, a detectivity of ∼10¹⁶ Jones is achieved, which is a record for halide perovskite nanocrystals. Simple A-site salt (FABr) treatments offer a mechanism for connecting between perovskite QDs for better charge transfer in high-quality devices. All of these important properties are superior to most advanced inorganic semiconductor phototransistors, indicating a promising future in optoelectronic applications.

Temperature-Dependent Photoluminescence of CdS/ZnS Core/Shell Quantum Dots for Temperature Sensors

Exploring the temperature-dependent photoluminescence (PL) properties of quantum dots (QDs) is not only important for understanding the carrier recombination processes in QD-based devices but also critical for expanding their special applications at different temperatures. However, there is still no clear understanding of the optical properties of CdS/ZnS core/shell QDs as a function of temperature. Herein, the temperature-dependent PL spectra of CdS/ZnS core/shell QDs were studied in the temperature range of 77-297 K. It was found that the band-edge emission (BEE) intensity decreases continuously with increasing temperature, while the surface-state emission (SSE) intensity first increases and then decreases. For BEE intensity, in the low temperature range, a small activation energy (29.5 meV) in the nonradiative recombination process led to the decrease of PL intensity of CdS/ZnS core/shell QDs; and at high temperature the PL intensity attenuation was caused by the thermal escape process. On the other hand, the temperature-dependent variation trend of the SSE intensity was determined by the competition of the trapping process of the surface trap states and the effect of thermally activated non-radiative defects. As the temperature increased, the PL spectra showed a certain degree of redshift in the peak energies of both band-edge and surface states and the PL spectrum full width at half-maximum (FWHM) increases, which was mainly due to the coupling of exciton and acoustic phonon. Furthermore, the CIE chromaticity coordinates turned from (0.190, 0.102) to (0.302, 0.194), which changed dramatically with temperature. The results indicated that the CdS/ZnS core/shell QDs are expected to be applied in temperature sensors.

Planar defect-free pure red perovskite light-emitting diodes via metastable phase crystallization

Solution-processable all-inorganic CsPbI_3-xBr_x perovskite holds great potential for pure red light-emitting diodes. However, the widely existing defects in this mixed halide perovskite markedly limit the efficiency and stability of present light-emitting diode devices. We here identify that intragrain Ruddlesden-Popper planar defects are primary forms of such defects in the CsPbI_3-xBr_x thin film owing to the lattice strain caused by inhomogeneous halogen ion distribution. To eliminate these defects, we develop a stepwise metastable phase crystallization strategy to minimize the CsPbI_3-xBr_x perovskite lattice strain, which brings planar defect-free CsPbI_3-xBr_x thin film with improved radiative recombination, narrowed emission band, and enhanced spectral stability. Using these high-quality thin films, we fabricate spectrally stable pure red perovskite light-emitting diodes, showing 17.8% external quantum efficiency and 9000 candela meter^-2 brightness with color coordinates required by Rec. 2020.

In situ synthesis of high-quantum-efficiency and stable bromide-based blue-emitting perovskite nanoplatelets

We present a facile synthetic approach for the growth of two-dimensional CsPbBr₃ nanoplatelets (NPLs) in the temperature range of 50-80 °C via the vacuum-assisted low-temperature (VALT) method. In this method, we utilized the solubility of the PbBr₂ precursor at temperatures high than the reaction temperature, thus making Br available during the reaction to form NPLs with fewer defects. The high chemical availability of Br during the reaction changes the growth dynamics and formation of highly crystalline nanoplatelets. Using this method, we have synthesized NPLs with an emission wavelength range of 450 to 485 nm that have high photoluminescence quantum yields (PLQY) from 80 to 100%. The synthesized NPLs retain their initial PLQY of about 80% after one month at ambient conditions. The formation of NPLs with fewer defects and enhanced radiative recombination was further confirmed by X-ray diffraction (XRD), reduced Urbach energy, time-resolved photocurrent measurements, X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared (FTIR) spectroscopy. Additionally, we utilized the synthesized NPLs for the fabrication of down-conversion light emitting diodes (LEDs), and the electroluminescence peak was barely shifted compared to the photoluminescence peak.

Lattice distortion inducing exciton splitting and coherent quantum beating in CsPbI3 perovskite quantum dots

Anisotropic exchange splitting in semiconductor quantum dots results in bright-exciton fine-structure splitting important for quantum information processing. Direct measurement of fine-structure splitting usually requires single/few quantum dots at liquid-helium temperature because of its sensitivity to quantum dot size and shape, whereas measuring and controlling fine-structure splitting at an ensemble level seem to be impossible unless all the dots are made to be nearly identical. Here we report strong bright-exciton fine-structure splitting up to 1.6 meV in solution-processed CsPbI₃ perovskite quantum dots, manifested as quantum beats in ensemble-level transient absorption at liquid-nitrogen to room temperature. The splitting is robust to quantum dot size and shape heterogeneity, and increases with decreasing temperature, pointing towards a mechanism associated with orthorhombic distortion of the perovskite lattice. Effective-mass-approximation calculations reveal an intrinsic 'fine-structure gap' that agrees well with the observed fine-structure splitting. This gap stems from an avoided crossing of bright excitons confined in orthorhombically distorted quantum dots that are bounded by the pseudocubic {100} family of planes.

Layer-by-layer assembly of CsPbX3 nanocrystals into large-scale homostructures

Advances in surface chemistry of CsPbX₃ (where X = Cl, Br or I) nanocrystals (NCs) enabled the replacement of native chain ligands in solution. However, there are few reports on ligand exchange carried out on CsPbX₃ NC thin films. Solid-state ligand exchange can improve the photoluminescence quantum yield (PLQY) of the film and promote a change in solubility of the solid surface, thus enabling multiple depositions of subsequent nanocrystal layers. Fine control of nanocrystal film thickness is of importance for light-emitting diodes (LEDs), solar cells and lasers alike. The thickness of the emissive material film is crucial to assure the copious recombination of charges injected into a LED, resulting in bright electroluminescence. Similarly, solar cell performance is determined by the amount of absorbed light, and hence the light absorber content in the device. In this study, we demonstrate a layer-by-layer (LbL) assembly method that results in high quality films, whose thicknesses can be finely controlled. In the solid state, we replaced oleic acid and oleylamine ligands with didodecyldimethylammonium bromide or ammonium thiocyanate that enhance the PLQY of the film. The exchange is carried out through a spin-coating technique, using solvents with strategic polarity to avoid NC dissolution or damage. Exploiting this technique, the deposition of various layers results in considerable thickening of films as proven by atomic force microscope measurements. The ease of handling of our combined process (i.e. ligand exchange and layer-by-layer deposition) enables thickness control over CsPbX₃ NC films with applicability to other perovskite nanomaterials paving the way for a large variety of layer permutations.

Recent progress and future prospects on halide perovskite nanocrystals for optoelectronics and beyond

As an emerging new class of semiconductor nanomaterials, halide perovskite (ABX₃, X = Cl, Br, or I) nanocrystals (NCs) are attracting increasing attention owing to their great potential in optoelectronics and beyond. This field has experienced rapid breakthroughs over the past few years. In this comprehensive review, halide perovskite NCs that are either freestanding or embedded in a matrix (e.g., perovskites, metal-organic frameworks, glass) will be discussed. We will summarize recent progress on the synthesis and post-synthesis methods of halide perovskite NCs. Characterizations of halide perovskite NCs by using a variety of techniques will be present. Tremendous efforts to tailor the optical and electronic properties of halide perovskite NCs in terms of manipulating their size, surface, and component will be highlighted. Physical insights gained on the unique optical and charge-carrier transport properties will be provided. Importantly, the growing potential of halide perovskite NCs for advancing optoelectronic applications and beyond including light-emitting devices (LEDs), solar cells, scintillators and X-ray imaging, lasers, thin-film transistors (TFTs), artificial synapses, and light communication will be extensively discussed, along with prospecting their development in the future.

High-Performance Perovskite Quantum Dot Solar Cells Enabled by Incorporation with Dimensionally Engineered Organic Semiconductor

Perovskite quantum dots (PQDs) have been considered promising and effective photovoltaic absorber due to their superior optoelectronic properties and inherent material merits combining perovskites and QDs. However, they exhibit low moisture stability at room humidity (20-30%) owing to many surface defect sites generated by inefficient ligand exchange process. These surface traps must be re-passivated to improve both charge transport ability and moisture stability. To address this issue, PQD-organic semiconductor hybrid solar cells with suitable electrical properties and functional groups might dramatically improve the charge extraction and defect passivation. Conventional organic semiconductors are typically low-dimensional (1D and 2D) and prone to excessive self-aggregation, which limits chemical interaction with PQDs. In this work, we designed a new 3D star-shaped semiconducting material (Star-TrCN) to enhance the compatibility with PQDs. The robust bonding with Star-TrCN and PQDs is demonstrated by theoretical modeling and experimental validation. The Star-TrCN-PQD hybrid films show improved cubic-phase stability of CsPbI₃-PQDs via reduced surface trap states and suppressed moisture penetration. As a result, the resultant devices not only achieve remarkable device stability over 1000 h at 20-30% relative humidity, but also boost power conversion efficiency up to 16.0% via forming a cascade energy band structure.

Recent progress of single-halide perovskite nanocrystals for advanced displays

Light-emitting diodes based on lead halide perovskite nanocrystals (LHP NCs) have shown an astonishing increase in efficiency in just several years of academic research, reaching high external quantum efficiencies exceeding 20%. The extensive color-tunability and narrow emission bandwidth of LHP NCs, in particular, are of great importance in the creation of the next generation of ultra-high-definition displays, as defined by the Rec. 2020 standard recommendation. In fact, whereas the colour of LHP NCs can be easily tuned by the compositions of halogens, the ion migration in mixed-halide perovskites under the electric field will seriously affect the spectral stability and operational lifetimes of perovskite light-emitting diodes (PeLEDs). Therefore, it is essential to realize efficient colour-saturated PeLEDs based on single-halide perovskite NCs. In this review, we focus on the recent progress in LHP NC-based PeLEDs and highlight the strategy of tuning the spectral emission based on quantum confinement or cation alloying/doping in single-halide perovskite NCs. Finally, we will give an outlook on future research avenues for preparing high-efficiency pure green, red and blue PeLEDs based on single-halide perovskite NCs.