Ion-Selective Electrodes Using Carbon Nanotubes as Ion-to-Electron Transducers

A physical entrapment method for the preparation of carbon nanotube reinforced macroporous adsorption resin with enhanced selective extraction performance

In this paper, we demonstrate a novel carbon nanotube (CNT) reinforced macroporous adsorption resin (MAR) for the first time. The CNTs were dispersed in water via sonication, and then in situ physically entrapped in the pores of MAR by capillary forces and sonication. The resulting CNT reinforced MAR (CNT-MAR) was proved by transmission electron microscopy (TEM) and confocal laser scanning microscopy (CLSM), and subsequently applied to extract a mixture of 8 types, 14 natural products. For comparison, the extraction efficiency of original MAR without CNTs was also evaluated. After extraction, the supernatants were detected via high-performance liquid chromatography (HPLC). The results indicated that the introduction of carbon nanotubes (CNTs) into the pores of MAR can significantly improve the adsorptive selectivity of MAR for natural products. The original MAR without CNTs has almost the same adsorption capacity for selectively extracting 3 types of natural products (phenols, alkaloids and anthraquinones). However, the CNT-MAR only could selectively extract anthraquinones and the adsorption capacity for three anthraquinone natural products is 1.46-1.83 times higher than that of unmodified MAR. In order to achieve the highest extraction efficiency of CNT-MAR for anthraquinone natural products, the main extraction parameters such as the extraction time and the pH value were also optimized. The CNT-MAR demonstrated an excellent ability to extract anthraquinone natural products with high selectivity and adsorption capacity. Due to its low cost, easy preparation and use, and operational characteristics, it shows great potential for selective extraction of natural products.

Amperometric Ion Sensing Approaches at Liquid/Liquid Interfaces for Inorganic, Organic and Biological Ions

Electrochemistry at the interface between two immiscible electrolyte solutions (ITIES) has become an invaluable tool for the selective and sensitive detection of cationic and anionic species, including charged drug molecules and proteins. In addition, neutral molecules can also be detected at the ITIES via enzymatic reactions. This chapter highlights recent developments towards creating a wide spectrum of sensing platforms involving ion transfer across the ITIES. As well as outlining the basic principles needed for performing these sensing applications, the development of ITIES-based detection strategies for inorganic, organic, and biological ions is discussed.

All-solid-state potentiometric sensors with a multiwalled carbon nanotube inner transducing layer for anion detection in environmental samples

While ion to electron transducing layers for the fabrication of potentiometric membrane electrodes for the detection of cations have been well established, similar progress for the sensing of anions has not yet been realized. We report for this reason on a novel approach for the development of all-solid-state anion selective electrodes using lipophilic multiwalled carbon nanotubes (f-MWCNTs) as the inner ion to electron transducing layer. This material can be solvent cast, as it conveniently dissolves in tetrahydrofuran (THF), an important advantage to develop uniform films without the need for using surfactants that might deteriorate the performance of the electrode. Solid contact sensors for carbonate, nitrate, nitrite, and dihydrogen phosphate are fabricated and characterized, and all exhibit comparable analytical characteristics to the inner liquid electrodes. For example, the carbonate sensor exhibits a Nernstian slope of 27.2 ± 0.8 mV·dec(-1), a LOD = 2.3 μM, a response time of 1 s, a linear range of four logarithmic units, and a medium-term stability of 0.04 mV·h(-1) is obtained in a pH 8.6 buffered solution. Water layer test, reversibility, and selectivity for chloride, nitrate, and hydroxide are also reported. The excellent properties of f-MWCNTs as a transducer are contrasted to the deficient performance of poly(3-octyl-thiophene) (POT) for carbonate detection. This is evidenced both with a significant drift in the potentiometric measures as well as a pronounced sensitivity to light (either sunlight or artificial light). This latter aspect may compromise its potential for environmental in situ measurements (night/day cycles). The concentration of carbonate is determined in a river sample (Arve river, Geneva) and compared to a reference method (automatic titrator with potentiometric pH detection). The results suggest that nanostructured materials such as f-MWCNTs are an attractive platform as a general ion-to-electron transducer for anion-selective electrodes.

Selective ion-sensing with membrane-functionalized electrolyte-gated carbon nanotube field-effect transistors

In this work the ion-selective response of an electrolyte-gated carbon-nanotube field-effect transistor (CNT-FET) towards K(+), Ca(2+) and Cl(-) in the biologically relevant concentration range from 10(-1) M to 10(-6) M is demonstrated. The ion-selective response is achieved by modifying the gate-electrode of an electrolyte-gated CNT-FET with ion-selective membranes, which are selective towards the respective target analyte ions. The selectivity, assured by the ion-selective poly(vinyl chloride) based membrane, allows the successful application of the herein proposed K(+)-selective CNT-FET to detect changes in the K(+) activity in the μM range even in solutions containing different ionic backgrounds. The sensing mechanism relies on a superposition of both an ion-sensitive response of the CNT-network as well as a change of the effective gate potential present at the semiconducting channel due to a selective and ion activity-dependent response of the membrane towards different types of ions. Moreover, the combination of a CNT-FET as a transducing element gated with an ion-selective coated-wire electrode offers the possibility to miniaturize the already well-established conventional ion-selective electrode setup. This approach represents a valuable strategy for the realization of portable, multi-purpose and low-cost biosensing devices.

Application of nanostructured TCNQ to potentiometric ion-selective K(+) and Na(+) electrodes

A new type of potentiometric solid-state ion-selective electrode (SS-ISE) has been fabricated with an intermediate layer made of 7,7,8,8-tetracyanoquinodimethane (TCNQ) or its ion-radical salts and an ionophore-based ion-selective membrane. To show the influence of the TCNQ layer on electrode selectivity, sodium- and potassium-sensitive membranes were applied. A good Nernstian response with a slope of 59.24 mV/dec in the range from 10(-6.5) to 10(-1) M KCl and 58.68 mV/dec (10(-6) to 10(-1) M NaCl) was observed. The influence of an interfacial water film was assessed by an aqueous-layer test performed during potentiometric measurements. The stability of the electrical potential of the new solid-contact electrodes was tested by performing current-reversal chronopotentiometry, and the capacitance of the electrodes is 132 μF or 154 μF for K(+) and Na(+) solid-contact electrodes. These properties confirmed the analytical applicability of TCNQ-based SC-ISEs and should allow the development of a new solid-state ion sensor group.

Detection and characterization of cancer cells and pathogenic bacteria using aptamer-based nano-conjugates

Detection and characterization of cells using aptamers and aptamer-conjugated nanoprobes has evolved a great deal over the past few decades. This evolution has been driven by the easy selection of aptamers via in vitro cell-SELEX, permitting sensitive discrimination between target and normal cells, which includes pathogenic prokaryotic and cancerous eukaryotic cells. Additionally, when the aptamer-based strategies are used in conjunction with nanomaterials, there is the potential for cell targeting and therapeutic effects with improved specificity and sensitivity. Here we review recent advances in aptamer-based nano-conjugates and their applications for detecting cancer cells and pathogenic bacteria. The multidisciplinary research utilized in this field will play an increasingly significant role in clinical medicine and drug discovery.

Ion-selective electrodes with colloid-imprinted mesoporous carbon as solid contact

A new type of solid-contact ion-selective electrode (SC-ISE) has been developed that uses colloid-imprinted mesoporous (CIM) carbon with 24 nm diameter, interconnected mesopores as the intermediate layer between a gold electrode and an ionophore-doped ISE membrane. For a demonstration, valinomycin was used as K(+) ionophore, and a good Nernstian response with a slope of 59.5 mV/decade in the range from 10(-5.2) to 10(-1.0) M was observed. The high purity, low content of redox-active surface functional groups and intrinsic hydrophobic characteristics of CIM carbon prepared from mesophase pitch lead to outstanding performance of these sensors, with excellent resistance to the formation of a water layer and no interference caused by light, O2, and CO2. When a redox couple is introduced as an internal reference species, calibration-free SC-ISEs can be made with a standard deviation of E° as low as 0.7 mV. Moreover, the interconnected mesopore structure of ISE membrane-infused CIM carbon facilitates both ion and electron conduction and provides a large interfacial area with good ion-to-electron transduction. Because of the large double layer capacitance of CIM carbon, CIM carbon-based SC-ISEs exhibit excellent potential stability, as shown by chronopotentiometry and continuous potentiometric measurements. The capacitance of these electrodes as determined by chronopotentiometry is 1.0 mF, and the emf drift over 70 h is as low as 1.3 μV/h, making these electrodes the most stable SC-ISEs reported so far.

Microneedle-based transdermal sensor for on-chip potentiometric determination of K(+)

The determination of electrolytes is invaluable for point of care diagnostic applications. An ion selective transdermal microneedle sensor is demonstrated for potassium by integrating a hollow microneedle with a microfluidic chip to extract fluid through a channel towards a downstream solid-state ion-selective-electrode (ISE). 3D porous carbon and 3D porous graphene electrodes, made via interference lithography, are compared as solid-state transducers for ISE's and evaluated for electrochemical performance, stability, and selectivity. The porous carbon K(+) ISE's show better performance than the porous graphene K(+) ISE's, capable of measuring potassium across normal physiological concentrations in the presence of interfering ions with greater stability. This new microfluidic/microneedle platform shows promise for medical applications.

Rubber-based substrates modified with carbon nanotubes inks to build flexible electrochemical sensors

The development of a solid-contact potentiometric sensor based on conducting rubbers using a carbon nanotubes ink is described here. Commercial rubbers are turned into conductive ones by a simple and versatile method, i.e. painting an aqueous dispersion of single-walled carbon nanotubes on the polymer surface. On this substrate, both the working ion-selective electrode and the reference electrode are built in order to form an integrated potentiometric cell. As a proof-of-principle, selective potassium electrodes are fully characterized giving comparable performances to conventional electrodes (sensitivity, selectivity, stability, linear range, limit of detection and reproducibility). As an application of the rubber-based electrodes, a bracelet was constructed to measure potassium levels in artificial sweat. Since rubbers are ubiquitous in our quotidian life, this approach offers great promise for the generation of chemical information through daily objects.

A paper-based potentiometric cell for decentralized monitoring of Li levels in whole blood

A novel approach to monitor Li levels in blood in decentralized (out of the lab) settings is presented. The approach uses a potentiometric cell fully made with filter paper as a support. Electrodes were built using carbon nanotubes ink to create a conductive path and a suitable polymeric membrane. Solid-state ion-selective electrodes for Li and a reference electrode were built and optimized. The results obtained on real samples of serum and whole blood are comparable with those obtained by conventional standard approaches. This platform shows an outstanding performance for the direct, fast and low-cost monitoring of Li levels in blood.

A reference electrode based on polyvinyl butyral (PVB) polymer for decentralized chemical measurements

A new solid-state reference electrode using a polymeric membrane of polyvinyl butyral (PVB), Ag/AgCl and NaCl to be used in decentralized chemical measurements is presented. The electrode is made by drop-casting the membrane cocktail onto a glassy carbon (GC) substrate. A stable potential (less than 1 mV dec(-1)) over a wide range of concentrations for the several chemical species tested is obtained. No significant influence to changes in redox potential, light and pH are observed. The response of this novel electrode shows good correlation when compared with a conventional double-junction reference electrode. Also good long-term stability (90±33 μV/h) and a lifetime of approximately 4 months are obtained. Aspects related to the working mechanisms are discussed. Atomic Force Microscopy (AFM) studies reveal the presence of nanopores and channels on the surface, and electrochemical impedance spectroscopy (EIS) of optimized electrodes show low bulk resistances, usually in the kΩ range, suggesting that a nanoporous polymeric structure is formed in the interface with the solution. Future applications of this electrode as a disposable device for decentralized measurements are discussed. Examples of the utilization on wearable substrates (tattoos, fabrics, etc) are provided.

Simple and disposable potentiometric sensors based on graphene or multi-walled carbon nanotubes--carbon-plastic potentiometric sensors

A simple procedure leading to disposable potentiometric sensors using as a supporting electrode - electrical lead and transducer - a layer of carbon nanostructured material, either graphene or multi-walled nanotubes, is proposed, and the effect of the material used on the properties of the sensor is discussed. The obtained layers were partially covered with a conventional poly(vinyl chloride) (PVC) based ion-selective membrane to result in simple, planar, and disposable potentiometric sensors. The analytical performance of the thus obtained electrodes was compared with that of classical macroscopic all-solid-state ion-selective electrodes (e.g. employing poly(octylthiophene) as a solid contact and a similar ion-selective membrane). It was superior (taking into account detection limits or selectivity towards Na(+) ions) compared to that of other disposable sensors proposed recently. The observed excellent analytical performance was attributed to the applied method of preparation of carbon nanostructured materials, which does not require addition of a surfactant to obtain a stable suspension (ink) used to prepare the electrical lead and the transducer of the sensor. Although the proposed sensors are predominantly intended for disposable use, pronounced stability of potential readings was obtained in within-day experiments. Moreover, due to their high conductivity carbon-plastic electrodes can be also applied in polarized potentiometric measurements.

Multielectrode bisensor system for time-resolved monitoring of ion transport across an epithelial cell layer

An ion-selective multielectrode bisensor system is designed to ensure reliable real-time concentration measurements of sodium, potassium, chloride, and pH in a small volume of biological liquid bathing a living human bronchial epithelial cell monolayer. The bisensor system allows the monitoring of major ions, which are simultaneously transported through the epithelia in both directions.

Evidence for a surface confined ion-to-electron transduction reaction in solid-contact ion-selective electrodes based on poly(3-octylthiophene)

The ion-to-electron transduction reaction mechanism at the buried interface of the electrosynthesized poly(3-octylthiophene) (POT) solid-contact (SC) ion-selective electrode (ISE) polymeric membrane has been studied using synchrotron radiation-X-ray photoelectron spectroscopy (SR-XPS), near edge X-ray absorption fine structure (NEXAFS), and electrochemical impedance spectroscopy (EIS)/neutron reflectometry (NR). The tetrakis[3,5-bis(triflouromethyl)phenyl]borate (TFPB(-)) membrane dopant in the polymer ISE was transferred from the polymeric membrane to the outer surface layer of the SC on oxidation of POT but did not migrate further into the oxidized POT SC. The TFPB(-) and oxidized POT species could only be detected at the outer surface layer (≤14 Ǻ) of the SC material, even after oxidation of the electropolymerized POT SC for an hour at high anodic potential demonstrating that the ion-to-electron transduction reaction is a surface confined process. Accordingly, this study provides the first direct structural evidence of ion-to-electron transduction in the electropolymerized POT SC ISE by proving TFPB(-) transport from the polymeric ISE membrane to the oxidized POT SC at the buried interface of the SC ISE. It is inferred that the performance of the POT SC ISE is independent of the thickness of the POT SC but is instead contingent on the POT SC surface reactivity and/or electrical capacitance of the POT SC. In particular, the results suggest that the electropolymerized POT conducting polymer may spontaneously form a mixed surface/bulk oxidation state, which may explain the unusually high potential stability of the resulting ISE. It is anticipated that this new understanding of ion-to-electron transduction with electropolymerized POT SC ISEs will enable the development of new and improved devices with enhanced analytical performance attributes.

Solid contact ion-selective electrodes with a well-controlled Co(II)/Co(III) redox buffer layer

Solid contact ion-selective electrodes (ISEs) typically have an intermediate layer between the ion-selective membrane and the underlying solid electron conductor that is designed to reduce the irreproducibility and instability of the measured electromotive force (emf). Nevertheless, the electrode-to-electrode reproducibility of the emf of current solid contact ISEs is widely considered to be unsatisfactory. To address this problem, we report here a new method of constructing this intermediate layer based on the lipophilic redox buffer consisting of the Co(III) and Co(II) complexes of 1,10-phenanthroline ([Co(phen)3](3+/2+)) paired with tetrakis(pentafluorophenyl)borate as counterion. The resulting electrodes exhibit emf values with an electrode-to-electrode standard deviation as low as 1.7 mV after conditioning of freshly prepared electrodes for 1 h. While many prior examples of solid contact ISEs also used intermediate layers that contained redox active species, the selection of a balanced ratio of the reduced and oxidized species has typically been difficult and was often ignored, contributing to the emf irreproducibility. The ease of the control of the [Co(phen)3](3+)/[Co(phen)3](2+) ratio explains the high emf reproducibility, as confirmed by the emf decrease of 58 mV per 10-fold increase in the ratio of the reduced and oxidized redox buffer species. Use of a gold electrode modified with a self-assembled 1-hexanethiol monolayer as underlying electron conductor suppresses the formation of a water layer and results in an electrode-to-electrode standard deviation of E° of 1.0 mV after 2 weeks of exposure to KCl solution.

Carbon nanotube-based aptasensors for the rapid and ultrasensitive detection of bacteria

In this paper we present a new generation of potentiometric biosensors based on carbon nanotubes (transducer layer of the biosensor) and aptamers (sensing layer of the biosensor) for the ultralow and selective detection of microorganisms. We show that with these aptasensors we were able to detect a few CFU of the target bacteria almost in real-time, both in buffered and in real samples.

Potentiometric sensors using cotton yarns, carbon nanotubes and polymeric membranes

A simple and generalized approach to build electrochemical sensors for wearable devices is presented. Commercial cotton yarns are first turned into electrical conductors through a simple dyeing process using a carbon nanotube ink. These conductive yarns are then partially coated with a suitable polymeric membrane to build ion-selective electrodes. Potentiometric measurements using these yarn-potentiometric sensors are demonstrated. Examples of yarns that can sense pH, K(+) and NH4(+) are presented. In all cases, these sensing yarns show limits of detection and linear ranges that are similar to those obtained with lab-made solid-state ion-selective electrodes. Through the immobilization of these sensors in a band-aid, it is shown that this approach could be easily implemented in a wearable device. Factors affecting the performance of the sensors and future potential applications are discussed.