Recent Advances in Heterogeneous Photocatalytic CO2 Conversion to Solar Fuels

Tunable Selectivity in CO2 Photo-Thermal Reduction by Perovskite-Supported Pd Nanoparticles

Photo-thermal catalysis has recently emerged as a promising alternative to overcome the limitations of traditional photocatalysis. Despite its potential, most of the photo-thermal systems still lack adequate selectivity patterns and appropriate analysis of the underlying reaction pathways, thus hampering a wide implementation. Herein, a novel photocatalyst based on Pd nanoparticles (NPs) supported on barium titanate (BTO) was prepared for the selective photo-thermal reduction of CO₂ and displayed catalytic rates of up to 8.2 mol_CO  g_Pd ^-1  h^-1 . The photocatalyst allowed for a tailored selectivity towards CO or CH₄ as a function of the metal loading or the light intensity. Mechanistic studies indicated that both thermal and non-thermal contributions of light played a role in the overall reaction pathway, each of them being dominant upon changing reaction conditions.

The Regulation of O2 Spin State and Direct Oxidation of CO at Room Temperature Using Triboelectric Plasma by Harvesting Mechanical Energy

Oxidation reactions play a critical role in processes involving energy utilization, chemical conversion, and pollutant elimination. However, due to its spin-forbidden nature, the reaction of molecular dioxygen (O₂) with a substrate is difficult under mild conditions. Herein, we describe a system that activates O₂ via the direct modulation of its spin state by mechanical energy-induced triboelectric corona plasma, enabling the CO oxidation reaction under normal temperature and pressure. Under optimized reaction conditions, the activity was 7.2 μmol h^-1, and the energy consumption per mole CO was 4.2 MJ. The results of kinetic isotope effect, colorimetry, and density functional theory calculation studies demonstrated that electrons generated in the triboelectric plasma were directly injected into the antibonding orbital of O₂ to form highly reactive negative ions O₂^-, which effectively promoted the rate-limiting step of O₂ dissociation. The barrier of the reaction of O₂^- ions and CO molecular was 3.4 eV lower than that of O₂ and CO molecular. This work provides an effective strategy for using renewable and green mechanical energy to realize spin-forbidden reactions of small molecules.

Influence of Ag Clusters on the Electronic Structures of β-Ga2O3 Photocatalyst Surfaces

In order to understand the photocatalytic carbon dioxide reduction over Ag-loaded β-Ga₂O₃ photocatalysts, first principles calculations based on density functional theory were performed on the surface model of a Ag cluster-adsorbed β-Ga₂O₃ system. The stable adsorption structures of Ag _n (n = 1 to 4) clusters on the β-Ga₂O₃ (100) surface were determined. In the electronic structure analysis, the valence states of all Ag clusters mixed with the top of the O 2p valence band of Ga₂O₃, leading the Fermi level of Ag _n /β-Ga₂O₃ to shift to the bottom of the conduction band. It was also revealed that the unoccupied states of Ag _n clusters overlapped with the Ga unoccupied states, and occupied electronic states of Ag clusters were formed in the band gap. These calculation results corresponded to the experimental ones obtained in our previous study, i.e., small Ag clusters had strong interaction with the Ga₂O₃ surface, enhancing the electron transfer between the Ag clusters and the Ga₂O₃ surface. That is, excited electrons toward Ag _n clusters or the perimeter of Ag-Ga₂O₃ should be the important key to promote photocatalytic CO₂ reduction.

Turbulence Enhancement and Mixing Analysis for Multi-Inlet Vortex Photoreactor for CO2 Reduction

In this article, we describe a prototype photoreactor of which the geometrical configuration was obtained by Genetic Algorithms to maximize the residence time of the reactant gases. A gas reaction mixture of CO2:H2O (1:2 molar ratio) was studied from the fluid dynamic point of view. The two main features of this prototype reactor are the conical shape, which enhances the residence time as compared to a cylindrical shape reference reactor, and the inlet heights and position around the main chamber that enables turbulence and mass transfer control. Turbulence intensity, mixing capability, and residence time attributes for the optimized prototype reactor were calculated with Computational Fluid Dynamics (CFD) software and compared with those from a reference reactor. Turbulence intensity near the envisioned catalytic bed was one percentage point higher in the reference than in the optimized prototype reactor. Finally, the homogeneity of the mixture was guaranteed since both types of reactors had a turbulent regime, but for the prototype the CO2 mass fraction was found to be better distributed.

Pivotal Role of Holes in Photocatalytic CO2 Reduction on TiO2

Evidence is provided that in a gas-solid photocatalytic reaction the removal of photogenerated holes from a titania (TiO₂ ) photocatalyst is always detrimental for photocatalytic CO₂ reduction. The coupling of the reaction to a sacrificial oxidation reaction hinders or entirely prohibits the formation of CH₄ as a reduction product. This agrees with earlier work in which the detrimental effect of oxygen-evolving cocatalysts was demonstrated. Photocatalytic alcohol oxidation or even overall water splitting proceeds in these reaction systems, but carbon-containing products from CO₂ reduction are no longer observed. H₂ addition is also detrimental, either because it scavenges holes or because it is not an efficient proton donor on TiO₂ . The results are discussed in light of previously suggested reaction mechanisms for photocatalytic CO₂ reduction. The formation of CH₄ from CO₂ is likely not a linear sequence of reduction steps but includes oxidative elementary steps. Furthermore, new hypotheses on the origin of the required protons are suggested.

Point-Defect Engineering: Leveraging Imperfections in Graphitic Carbon Nitride (g-C3 N4 ) Photocatalysts toward Artificial Photosynthesis

Graphitic carbon nitride (g-C₃ N₄ ) is a kind of ideal metal-free photocatalysts for artificial photosynthesis. At present, pristine g-C₃ N₄ suffers from small specific surface area, poor light absorption at longer wavelengths, low charge migration rate, and a high recombination rate of photogenerated electron-hole pairs, which significantly limit its performance. Among a myriad of modification strategies, point-defect engineering, namely tunable vacancies and dopant introduction, is capable of harnessing the superb structural, textural, optical, and electronic properties of g-C₃ N₄ to acquire an ameliorated photocatalytic activity. In view of the burgeoning development in this pacey field, a timely review on the state-of-the-art advancement of point-defect engineering of g-C₃ N₄ is of vital significance to advance the solar energy conversion. Particularly, insights into the intriguing roles of point defects, the synthesis, characterizations, and the systematic control of point defects, as well as the versatile application of defective g-C₃ N₄ -based nanomaterials toward photocatalytic water splitting, carbon dioxide reduction and nitrogen fixation will be presented in detail. Lastly, this review will conclude with a balanced perspective on the technical and scientific hindrances and future prospects. Overall, it is envisioned that this review will open a new frontier to uncover novel functionalities of defective g-C₃ N₄ -based nanostructures in energy catalysis.

Semiconductor photocatalysts and mechanisms of carbon dioxide reduction and nitrogen fixation under UV and visible light

The review summarizes the current knowledge about heterogeneous semiconductor photocatalysts that are active towards photocatalytic reduction of carbon dioxide and molecular nitrogen under visible and near-UV light. The main classes of these photocatalysts and characteristic features of their application in the target processes are considered. Primary attention is given to photocatalysts based on titanium dioxide, which have high activity and stability in the carbon dioxide reduction. For the first time, the photofixation of nitrogen under irradiation in the presence of various semiconductor materials is considered in detail.

The bibliography includes 264 references.

A Critical Review on Black Phosphorus-Based Photocatalytic CO2 Reduction Application

Energy shortages and greenhouse effects are two unavoidable problems that need to be solved. Photocatalytically converting CO₂ into a series of valuable chemicals is considered to be an effective means of solving the above dilemmas. Among these photocatalysts, the utilization of black phosphorus for CO₂ photocatalytic reduction deserves a lightspot not only for its excellent catalytic activity through different reaction routes, but also on account of the great preponderance of this relatively cheap catalyst. Herein, this review offers a summary of the recent advances in synthesis, structure, properties, and application for CO₂ photocatalytic reduction. In detail, the review starts from the basic principle of CO₂ photocatalytic reduction. In the following section, the synthesis, structure, and properties, as well as CO₂ photocatalytic reduction process of black phosphorus-based photocatalyst are discussed. In addition, some possible influencing factors and reaction mechanism are also summarized. Finally, a summary and the possible future perspectives of black phosphorus-based photocatalyst for CO₂ reduction are established.

Electrochemical CO2 Reduction on Cu: Synthesis-Controlled Structure Preference and Selectivity

The electrochemical CO2 reduction reaction (ECO2 RR) on Cu catalysts affords high-value-added products and is therefore of great practical significance. The outcome and kinetics of ECO2 RR remain insufficient, requiring essentially the optimized structure design for the employed Cu catalyst, and also the fine synthesis controls. Herein, synthesis-controlled structure preferences and the modulation of intermediate's interactions are considered to provide synthesis-related insights on the design of Cu catalysts for selective ECO2 RR. First, the origin of ECO2 RR intermediate-dominated selectivity is described. Advanced structural engineering approaches, involving alloy/compound formation, doping/defect introduction, and the use of specific crystal facets/amorphization, heterostructures, single-atom catalysts, surface modification, and nano-/microstructures, are then reviewed. In particular, these structural engineering approaches are discussed in association with diversified synthesis controls, and the modulation of intermediate generation, adsorption, reaction, and additional effects. The results pertaining to synthetic methodology-controlled structural preferences and the correspondingly motivated selectivity are further summarized. Finally, the current opportunities and challenges of Cu catalyst fabrication for highly selective ECO2 RR are discussed.

Technologies and perspectives for achieving carbon neutrality

Global development has been heavily reliant on the overexploitation of natural resources since the Industrial Revolution. With the extensive use of fossil fuels, deforestation, and other forms of land-use change, anthropogenic activities have contributed to the ever-increasing concentrations of greenhouse gases (GHGs) in the atmosphere, causing global climate change. In response to the worsening global climate change, achieving carbon neutrality by 2050 is the most pressing task on the planet. To this end, it is of utmost importance and a significant challenge to reform the current production systems to reduce GHG emissions and promote the capture of CO2 from the atmosphere. Herein, we review innovative technologies that offer solutions achieving carbon (C) neutrality and sustainable development, including those for renewable energy production, food system transformation, waste valorization, C sink conservation, and C-negative manufacturing. The wealth of knowledge disseminated in this review could inspire the global community and drive the further development of innovative technologies to mitigate climate change and sustainably support human activities.

Reticular-Chemistry-Inspired Supramolecule Design as a Tool to Achieve Efficient Photocatalysts for CO2 Reduction

Photocatalytic CO₂ reduction into C1 products is one of the most trending research subjects of current times as sustainable energy generation is the utmost need of the hour. In this review, we have tried to comprehensively summarize the potential of supramolecule-based photocatalysts for CO₂ reduction into C1 compounds. At the outset, we have thrown light on the inert nature of gaseous CO₂ and the various challenges researchers are facing in its reduction. The evolution of photocatalysts used for CO₂ reduction, from heterogeneous catalysis to supramolecule-based molecular catalysis, and subsequent semiconductor-supramolecule hybrid catalysis has been thoroughly discussed. Since CO₂ is thermodynamically a very stable molecule, a huge reduction potential is required to undergo its one- or multielectron reduction. For this reason, various supramolecule photocatalysts were designed involving a photosensitizer unit and a catalyst unit connected by a linker. Later on, solid semiconductor support was also introduced in this supramolecule system to achieve enhanced durability, structural compactness, enhanced charge mobility, and extra overpotential for CO₂ reduction. Reticular chemistry is seen to play a pivotal role as it allows bringing all of the positive features together from various components of this hybrid semiconductor-supramolecule photocatalyst system. Thus, here in this review, we have discussed the selection and role of various components, viz. the photosensitizer component, the catalyst component, the linker, the semiconductor support, the anchoring ligands, and the peripheral ligands for the design of highly performing CO₂ reduction photocatalysts. The selection and role of various sacrificial electron donors have also been highlighted. This review is aimed to help researchers reach an understanding that may translate into the development of excellent CO₂ reduction photocatalysts that are operational under visible light and possess superior activity, efficiency, and selectivity.

Solar-driven conversion of carbon dioxide over nanostructured metal-based catalysts in alternative approaches: Fundamental mechanisms and recent progress

Solar-driven carbon dioxide (CO₂) conversion has gained tremendous attention as a prominent strategy to simultaneously reduce the atmospheric CO₂ concentration and convert solar energy into solar fuels in the form of chemical bonds. Numerous efforts have been devoted to diverse photo-driven processes for CO₂ conversion, which utilized a multidisciplinary strategy. Among them, the architecture of nanostructured metal-based catalysts is emerging as an eminent solution for the design of catalysts of this field. In this work, we first provide fundamental mechanisms of photochemical, photoelectrochemical, photothermal, and photobio(electro)chemical CO₂ reduction processes to achieve an in-deep understanding of vital aspects. Importantly, the recent progress in the catalyst design for each reaction system is discussed and highlighted. Based on these analyses, an overview of photo-driven CO₂ reduction on metal-based catalysts for solar fuel production is also spotlighted. Finally, we analyze challenges and prospects for the strategic direction of developments in the field.

Significantly Enhanced Photocatalytic CO2 Reduction by Surface Amorphization of Cocatalysts

Rational phase engineering of reduction cocatalyst offers a promising route to modulate the photocatalytic activity and selectivity in the conversion of CO2 to chemical feedstocks. However, it remains a great challenge to choose a suitable phase given that high-crystallinity phase is more conducive to the charge transfer and separation, while amorphous phase is more favorable for the adsorption and activation of CO2 molecules. To resolve this dilemma, herein, with Pd as a well-defined model, a surface amorphization strategy has been developed to fabricate crystalline@amorphous semi-core-shell cocatalysts based on the transformation of outer layer atoms of crystalline cocatalysts to disorder phase. According to the theoretical and experimental analysis, in the heterostructured cocatalysts, crystalline core shuttles the photoexcited electrons from light-harvesting semiconductor to amorphous shell due to its strong electronic coupling with both components. Meanwhile, amorphous shell provides efficient active sites for preferential activation and conversion of CO2 and suppression of undesirable proton reduction. Benefiting from the synergistic effects between crystalline core and amorphous shell, the optimized heterophase cocatalyst with suitable thickness of amorphous shell achieves superior CO (22.2 µmol gcat-1 h-1 ) and CH4 (38.1 µmol gcat-1 h-1 ) formation rates with considerable selectivity and high stability in comparison with crystalline and amorphous counterparts.

Enhanced light-driven CO2 reduction on metal-free rich terminal oxygen-defects carbon nitride nanosheets

Exploiting highly-efficient and metal-free photocatalyst for CO₂ conversion into useful chemicals is a promising pathway to solve the energy and environmental crises. In this work, through a facile exfoliation process, an ultra-thin and short-range order g-C₃N₄ nanosheet with rich terminal oxygen defects is successfully constructed, which presents total electron yield of 36.30 μmol g^-1h^-1, 3.05 times higher than that of bulk one. The results affirms that both the van der Waals forces between the C₃N₄ layers and the CN bonds on the periodic heptazine units could be disrupted during the sonication process, thus achieving the ultra-thin and ultra-small g-C₃N₄ nanosheet, which enables the improvement of optical absorption and carrier separation abilities. The π-conjugated triazine rings structure is still remained but the terminal active C radicals tend to transform into oxygen defects which become the sites to bind and activate CO₂. The in-situ DRIFTS provides the direct evidence that the size regulation and oxygen-defects design strategy can effectively promote the CO₂ adsorption and activation process upon the photocatalyst, thus turning out to boost the reactivity toward CO₂.

Brookite TiO2 Nanoparticles Decorated with Ag/MnOx Dual Cocatalysts for Remarkably Boosted Photocatalytic Performance of the CO2 Reduction Reaction

The solar-driven CO₂ reduction reaction (CO₂RR) for producing chemical fuels is considered to be a promising approach to dealing with the growing energy crisis and greenhouse effect. Herein, novel Ag/MnO_x dual-cocatalyst-decorated brookite titania (BT) nanoparticles with remarkably boosted photocatalytic CO₂RR performance are prepared through a facile photodeposition method. The resultant xAg-BT-yMn composite with optimal cocatalyst content delivers amazing CO/CH₄ yields of 31.70/129.98 μmol g^-1 with an overall photoactivity of 1103.28 μmol g^-1 h^-1, 11.98 times higher than that of the BT nanoparticles alone. Further investigations demonstrate that the dual cocatalysts decorating the BT nanoparticles not only effectively retard the photoinduced charge recombination but also significantly vary the surface chemical feature to promote the adsorption/activation of the reactants (CO₂/H₂O). In addition, the Ag nanoparticles can broaden the spectral response region, while the MnO_x cocatalyst can promote the CH₄ product selectivity and the water oxidation reaction. The synergistic effect of Ag/MnO_x dual cocatalysts on the BT nanoparticles renders a remarkably boosted CO₂RR performance, which provides a simple yet general synthesis strategy for brookite titania-based photocatalysts with high-performance solar-driven CO₂ conversion.

Integration of zirconium-based metal-organic framework with CdS for enhanced photocatalytic conversion of CO2 to CO

It is a promising strategy to prepare composite photocatalysts based on MOFs and semiconductors for enhancing photocatalytic reduction of carbon dioxide (CO₂). A family of binary composite photocatalysts (CdS@UiO-66-NH₂) with different CdS contents have been designed and synthesized, which have been explored for photocatalytic reduction of CO₂. CdS@UiO-66-NH₂ can efficiently convert CO₂ into CO under visible light irradiation via the solid-gas mode in the absence of sacrificial agents and photosensitizers. The generation rate of CO can reach up to 280.5 μmol g^-1 h^-1, which is 2.13-fold and 2.9-fold improvements over the pristine CdS and UiO-66-NH₂, respectively, and the selectivity for CO is very high. Furthermore, this kind of photocatalysts can still maintain great photocatalytic activity in CO₂/N₂ mixed atmosphere with different CO₂ concentrations. The outstanding performances of CdS@UiO-66-NH₂ may be attributed to the existence of the direct Z-scheme heterojunction, which possesses the enhanced separation and migration of photo-generated charge carriers between UiO-66-NH₂ and CdS, available specific surface areas and improved visible light absorption ability as well as abundant reaction active sites. This case reveals that MOF-based composite photocatalysts exhibit promising potential applications in the field of CO₂ conversion.

Current and future perspectives on catalytic-based integrated carbon capture and utilization

There exist several well-known methods with varying maturity for capturing carbon dioxide from emission sources of different concentrations, including absorption, adsorption, cryogenics and membrane separation, among others. The capture and separation steps can produce almost pure CO₂, but at substantial cost for being conditioned for transport and final utilization, with high economical risks to be considered. A possible way for the elimination of this conditioning and cost is direct CO₂ utilization, whether on-site in a further process but within the same plant, or in-situ, coupling both capture and conversion in the same unit. This approach is usually called integrated carbon capture and utilization (ICCU) or integrated carbon capture and conversion (ICCC), and has lately started receiving considerable attention in many circles. As CO₂ is already industrially employed in other sectors, such as food preservation, water treatment and conversion to high added-value chemicals and fuels such as methanol, methane, etc., among others, it is of great interest to explore the global ICCC approach. Catalytic-based processes play a key role in CO₂ conversion, and different technologies are gaining great attention from both academia and industry. However, the 'big picture of ICCU' and in which technology the efforts should focus on at large scale is still unclear. This review analyzes some promising concepts of ICCU specifically on CO₂ catalytic conversion, highlighting their current commercial relevance as well as challenges that have to be faced today and in the next future.

Synergistic Integration of AuCu Co-Catalyst with Oxygen Vacancies on TiO2 for Efficient Photocatalytic Conversion of CO2 to CH4

Photocatalytic reduction of CO₂ toward eight-electron CH₄ product with simultaneously high conversion efficiency and selectivity remains great challenging owing to the sluggish charge separation and transfer kinetics and lack of active sites for the adsorption and activation of reactants. Herein, a defective TiO₂ nanosheet photocatalyst simultaneously equipped with AuCu alloy co-catalyst and oxygen vacancies (AuCu-TiO_2-x NSs) was rationally designed and fabricated for the selective conversion of CO₂ into CH₄. The experimental results demonstrated that the AuCu alloy co-catalyst not only effectively promotes the separation of photogenerated electron-hole pairs but also acts as synergistic active sites for the reduction of CO₂. The oxygen vacancies in TiO₂ contribute to the separation of charge carriers and, more importantly, promote the oxidation of H₂O, thus providing rich protons to promote the deep reduction of CO₂ to CH₄. Consequently, the optimal AuCu-TiO_2-x nanosheets (NSs) photocatalyst achieves a CO₂ reduction selectivity toward CH₄ up to 90.55%, significantly higher than those of TiO_2-x NSs (31.82%), Au-TiO_2-x NSs (38.74%), and Cu-TiO_2-x NSs (66.11%). Furthermore, the CH₄ evolution rate over the AuCu-TiO_2-x NSs reaches 22.47 μmol·g^-1·h^-1, which is nearly twice that of AuCu-TiO₂ NSs (12.10 μmol·g^-1·h^-1). This research presents a unique insight into the design and synthesis of photocatalyst with oxygen vacancies and alloy metals as the co-catalyst for the highly selective deep reduction of CO₂.

Improved photocatalytic activity and stability of InGaN quantum dots/C3N4heterojunction photoelectrode for CO2reduction and hydrogen production

Photocatalytic conversion of CO₂to produce fuel is considered a promising approach to reduce CO₂emissions and tackle energy crisis. GaN-based materials have been studied for CO₂reduction because of their excellent optical properties and band structure. However, low photocatalytic activity and severe photocorrosion of GaN-based photoelectrode greatly limit their applications. In this work, photocatalytic activity was improved by adopting InGaN quantum dots (QDs) combined with C₃N₄nano-sheets as photoanode, and thus the efficiency of CO₂reduction and the selectivity of hydrogen production were increased significantly. In addition, the photoelectron-chemical corrosion of photoelectrodes has been apparently controlled. InGaN QDs/C₃N₄has the highest CO and H₂productions rates of 14.69μmol mol^-1h^-1and 140μmol mol^-1h^-1which were 2.2 times and 14.5 times than that of InGaN film photoelectrode, respectively. The enhancement of photocatalytic activity is attributed to C₃N₄modification and a large electric dipole forming on the surface of InGaN QDs, which facilitate the separation and transfer of photo-generated carriers and thus promote CO₂reduction reaction. This work provides a promising strategy for the development of GaN-based photoanodes with superior stability and efficiency.

Highly Dispersed Pt Nanoparticle-Doped Mesoporous ZnO Photocatalysts for Promoting Photoconversion of CO2 to Methanol

Photoreduction of CO₂ is considered a challenge due to the lack of effective photocatalysts with wide-spectrum absorption, active charge separation dynamically, and CO₂ adsorption. Herein, mesoporous Pt/ZnO nanocomposites with different Pt percentages (0.5-2%) have been fabricated using the sol-gel process in the presence of a template for CO₂ photoreduction during visible-light exposure. Pt nanoparticles (NPs) deposited onto mesoporous ZnO with a considerable surface area can effectively promote charge mobility. The mesoporous 1.5% Pt/ZnO nanocomposite exhibits an optimal CH₃OH yield (668 μmol g^-1), which is 18.5-fold larger than that of mesoporous ZnO (36 μmol g^-1). The most photoactive material was the 1.5% Pt/ZnO nanocomposite, producing CH₃OH of 668 μmol g^-1, and the production rate of CH₃OH over the 1.5% Pt/ZnO nanocomposite (74.11 μmol g^-1 h^-1) was increased 20 times in comparison with ZnO NPs (3.72 μmol g^-1 h^-1). The enhancement of CO₂ photoreduction efficiency over Pt/ZnO nanocomposites was attributed to the formation of the heterojunction at the Pt/ZnO interface, promoting a lower resistance to charge transfer and a larger electron transfer to the conduction band. Mesoporous Pt/ZnO nanocomposites offer enhanced accessibility and a larger surface area. Such an unparalleled mesostructure provides a new framework for the construction and design of photoactive materials with high-efficiency photocatalysts.

Single-Atom Electrocatalysts for Multi-Electron Reduction of CO2

The multi-electron reduction of CO₂ to hydrocarbons or alcohols is highly attractive in a sustainable energy economy, and the rational design of electrocatalysts is vital to achieve these reactions efficiently. Single-atom electrocatalysts are promising candidates due to their well-defined coordination configurations and unique electronic structures, which are critical for delivering high activity and selectivity and may accelerate the explorations of the activity origin at atomic level as well. Although much effort has been devoted to multi-electron reduction of CO₂ on single-atom electrocatalysts, there are still no reviews focusing on this emerging field and constructive perspectives are also urgent to be addressed. Herein recent advances in how to design efficient single-atom electrocatalysts for multi-electron reduction of CO₂ , with emphasis on strategies in regulating the interactions between active sites and key reaction intermediates, are summarized. Such interactions are crucial in designing active sites for optimizing the multi-electron reduction steps and maximizing the catalytic performance. Different design strategies including regulation of metal centers, single-atom alloys, non-metal single-atom catalysts, and tandem catalysts, are discussed accordingly. Finally, current challenges and future opportunities for deep electroreduction of CO₂ are proposed.

Sustained CO2-photoreduction activity and high selectivity over Mn, C-codoped ZnO core-triple shell hollow spheres

Solar conversion of CO₂ into energy-rich products is one of the sustainable solutions to lessen the global energy shortage and environmental crisis. Pitifully, it is still challenging to attain reliable and affordable CO₂ conversion. Herein, we demonstrate a facile one-pot approach to design core-triple shell Mn, C-codoped ZnO hollow spheres as efficient photocatalysts for CO₂ reduction. The Mn ions, with switchable valence states, function as “ionized cocatalyst” to promote the CO₂ adsorption and light harvesting of the system. Besides, they can capture photogenerated electrons from the conduction band of ZnO and provide the electrons for CO₂ reduction. This process is continuous due to the switchable valence states of Mn ions. Benefiting from such unique features, the prepared photocatalysts demonstrated fairly good CO₂ conversion performance. This work is endeavoured to shed light on the role of ionized cocatalyst towards sustainable energy production.

Photoreduction of CO₂ into energy-rich products is a sustainable solution to lessen the global energy and environmental crisis. Here the authors show that Mn ions in Mn, C-codoped ZnO hollow spheres function as “ionized cocatalyst” to promote the CO₂ adsorption and light harvesting to boost the CO₂ photoreduction activity.

Highly Efficient Photocatalytic CO2 Reduction in Two-Dimensional Ferroelectric CuInP2S6 Bilayers

Photocatalytic CO₂ conversion into reproducible chemical fuels (e.g., CO, CH₃OH, or CH₄) provides a promising scheme to solve the increasing environmental problems and energy demands simultaneously. However, the efficiency is severely restricted by the high overpotential of the CO₂ reduction reaction (CO₂RR) and rapid recombination of photoexcited carriers. Here, we propose that a novel type-II photocatalytic mechanism based on two-dimensional (2D) ferroelectric multilayers would be ideal for addressing these issues. Using density-functional theory and nonadiabatic molecular dynamics calculations, we find that the ferroelectric CuInP₂S₆ bilayers exhibit a staggered band structure induced by the vertical intrinsic electric fields. Different from the traditional type-II band alignment, the unique structure of the CuInP₂S₆ bilayer not only effectively suppresses the recombination of photogenerated electron-hole (e-h) pairs but also produces a sufficient photovoltage to drive the CO₂RR. The predicted recombination time of photogenerated e-h pairs, 1.03 ns, is much longer than the transferring times of photoinduced electrons and holes, 5.45 and 0.27 ps, respectively. Moreover, the overpotential of the CO₂RR will decrease by substituting an S atom with a Cu atom, making the redox reaction proceed spontaneously under solar radiation. The solar-to-fuel efficiency with an upper limit of 8.40% is achieved in the CuInP₂S₆ bilayer and can be further improved to 32.57% for the CuInP₂S₆ five-layer. Our results indicate that this novel type-II photocatalytic mechanism would be a promising way to achieve highly efficient photocatalytic CO₂ conversion based on the 2D ferroelectric multilayers.

Enhanced photocatalytic CO2 reduction with defective TiO2 nanotubes modified by single-atom binary metal components

A binary component catalyst consists of single atoms (SAs- Pt and Au) anchored on self-doped TiO₂ nanotubes (TNTs), was developed for photocatalytic CO₂ reduction. The defects introduced TNTs substrate was stabilized with atomic Pt and Au via strong metal support interactions (MSI), due to which, the covalent interactions facilitated an effective transfer of photo-generated electrons from the defective sites to the SAs, and in turn an enhanced separation of electron-hole pairs and charge-carrier transmission. The Pt-Au/R-TNTs with 0.33 wt% of SA metals, exhibited a maximum of 149 times higher photocatalytic performance than unmodified R-TNT and a total apparent quantum yield (AQY) of 17.9%, in which the yield of CH₄ and C₂H₆ reached to 360.0 and 28.8 μmol g^-1 h^-1, respectively. The metals loading shifted the oxidation path of H₂O from •OH generation into O₂ evolution, that inhibited the self-oxidization of the photocatalyst.

Sodium doped flaky carbon nitride with nitrogen defects for enhanced photoreduction carbon dioxide activity

Sodium doped flaky carbon nitride (g-C₃N₄) with nitrogen defects (bmw-DCN-x) were synthesized via two steps method to enhance photocatalytic reduction of carbon dioxide (CO₂). After ball milling and calcination, dicyandiamide was evenly dispersed on the sodium chloride (NaCl) template to form a flaky structure. The NaCl not only provided part of sodium (Na) source for Na doped g-C₃N₄, but also introduced a large number of nitrogen (N) defects. Meanwhile, sodium hydroxide (NaOH) significantly enhanced Na doping. The bmw-DCN-30, a proportion of modified g-C₃N₄, showed heightened photo-reduction CO₂ performance, with satisfactory carbon monoxide (CO) and methane (CH₄) productivity at a rate of 30.6 μmol·g^-1·h^-1 and 5.4 μmol·g^-1·h^-1 respectively. This productivity was 15 and 11 times as much as that of bulky g-C₃N₄ (BCN). The related characterizations confirmed that N defects produced more reactive sites and enhanced the adsorption capacity of carbon nitride to CO₂. The accompanying Na doping and flaky structure characteristics improved the optical absorption ability and the effective separation of photogenerated carriers. Accordingly, this work provides further insights into constructing modified materials based on carbon nitride for CO₂ reduction.

Engineering two-dimensional metal oxides and chalcogenides for enhanced electro- and photocatalysis

Two-dimensional (2D) metal oxides and chalcogenides (MOs & MCs) have been regarded as a new class of promising electro- and photocatalysts for many important chemical reactions such as hydrogen evolution reaction, CO₂ reduction reaction and N₂ reduction reaction in virtue of their outstanding physicochemical properties. However, pristine 2D MOs & MCs generally show the relatively poor catalytic performances due to the low electrical conductivity, few active sites and fast charge recombination. Therefore, considerable efforts have been devoted to engineering 2D MOs & MCs by rational structural design and chemical modification to further improve the catalytic activities. Herein, we comprehensively review the recent advances for engineering technologies of 2D MOs & MCs, which are mainly focused on the intercalation, doping, defects creation, facet design and compositing with functional materials. Meanwhile, the relationship between morphological, physicochemical, electronic, and optical properties of 2D MOs & MCs and their electro- and photocatalytic performances is also systematically discussed. Finally, we further give the prospect and challenge of the field and possible future research directions, aiming to inspire more research for achieving high-performance 2D MOs & MCs catalysts in energy storage and conversion fields.

CeO2/CuO/TiO2heterojunction photocatalysts for conversion of CO2to ethanol

An attempt to reduce CO₂emissions has led to the development of CeO₂/CuO/TiO₂heterojunction photocatalysts for photoconversion of CO₂to useful products, e.g. ethanol. Composite photocatalysts were simply prepared by mixing TiO₂(P25) with different mass ratios of CeO₂(1 wt%) and CuO (2 or 3 wt%) by ball milling. The prepared photocatalysts had uniformly distributed CeO₂and CuO phases, throughout the TiO₂phase. The integration of CeO₂and CuO into TiO₂at 1 wt% CeO₂and 3 wt% CuO produced a composite, with a reduced band gap of 2.88 eV, allowing absorption of lower energy light and a lower electron-hole recombination rate. The 1%CeO₂/3%CuO/TiO₂photocatalysts yielded ethanol at 30.5μmol g_cat^-1h^-1, almost three times higher than the yield from pure TiO₂. This improved CO₂conversion efficiency was due to contributions from properties of both additives: CeO₂increased light absorption, while CuO acted as an electron trap and enhanced CO₂adsorption. In addition, the heterojunction at the interfaces facilitated the photogenerated charge separation, which, in turn, increased the charge participation in the catalyzed conversion reactions.

Visible-light-driven photocatalysis of carbon dioxide and organic pollutants by MFeO2 (M = Li, Na, or K)

In recent years, lithium-containing ceramic materials have attracted considerable research attention as high-temperature adsorbents of carbon dioxide. The recycling of electrode materials from spent lithium-ion batteries for use as photocatalysts in recovering CO₂ and degrading organic pollutants is worthy of exploration. Solid, magnetic ferrite-containing photocatalysts are easily separated from reaction solutions by using magnetic devices. Solid catalysts (e.g., LiFeO₂, LiFe₅O₈, NaFeO₂, and K₂Fe₂O₄) were prepared through the calcination of Fe₂O₃ and M₂CO₃. CO₂ was photoreduced and crystal violet (CV) and 2-hydroxybenzoic acid (2-HBA) were photodegraded under visible light irradiation. The optimized K₂Fe₂O₄ photocatalyst increased the rate of photocatalytic conversion from CO₂ to methane at 20.9 µmol g^-1 h^-1. The catalytic efficiency indicated that the optimized reaction rate constants of CV with LiFeO₂, NaFeO₂, and K₂Fe₂O₄ were 2.98 × 10^-1, 5.32 × 10^-1, and 4.36 × 10^-1 h^-1, respectively. The quenching effect achieved through the use of various scavengers and the electron paramagnetic resonance in CV degradation revealed the substantial contribution of the reactive superoxide anion radical O₂^- and the minor roles of h⁺ and the OH radical. Its usefulness in the synthesis of solid-base catalyst MFeO₂ is promising for environmental control and relevant applications, particularly in solar energy manufacturing.

Cobalt-based metal-organic frameworks for the photocatalytic reduction of carbon dioxide

Metal-organic frameworks (MOFs) are porous materials composed of metal centers and organic connectors. They are formed by complexation reactions and exhibit characteristics of both polymers and coordination compounds. They exhibit numerous advantageous features, including a large specific surface area, adjustable pore size/shape, and modifiable pore wall functional groups. Consequently, MOFs have been extensively applied in the photocatalytic reduction of carbon dioxide (CO2). Despite considerable research on cobalt-based MOFs, the photocatalytic reduction of CO2 in the presence of these materials remains challenging. The present review summarizes the current studies concerning the utilization of cobalt-based MOFs in the photocatalytic reduction of CO2. Additionally, approaches used to enhance the catalytic reduction performance are evaluated and the challenges associated with Co-based MOFs are discussed.

DFT insight into the effect of Cu atoms on adsorption and dissociation of CO2 over a Pd8/ TiO2(101) surface

In order to improve the photocatalytic activity of a bimetallic cocatalyst, understanding its mechanism is very important for the development of a CO₂ photocatalyst. In this study, density functional theory (DFT) calculations were performed to investigate CO₂ adsorption and dissociation over Pd–Cu bimetallic clusters loaded on a TiO₂(101) surface, aiming at understanding the origin of the effect caused by the presence of Cu. The results demonstrated that the introduction of a Cu atom has a dual effect on the adsorption and dissociation of CO₂: (1) it provides the positive polarization charge center to enhance CO₂ adsorption, and (2) it up-shifts the d-band center of the Cu atom to improve the activation of CO₂. Thus, the activity of the Pd₇Cu₁/TiO₂(101) surface, as compared with that of the Pd₈/TiO₂(101) surface, can be significantly improved, and the active center is the introduced Cu atom. This result is not only helpful for the development of effective CO₂ photocatalysts but also crucial to understand the basic mechanism of bimetallic catalysis.

The Cu atom provides the positive polarization charge center to enhance CO₂ adsorption and up-shifts its d-band center to improve the activation of CO₂.

Improved charge separation and carbon dioxide photoreduction performance of surface oxygen vacancy-enriched zinc ferrite@titanium dioxide hollow nanospheres with spatially separated cocatalysts

Here, we describe the fabrication of surface oxygen vacancy-enriched ZnFe₂O₄@TiO₂ double-shell hollow heterostructure nanospheres (ZnFe₂O₄@H-TiO_2-x) coupled with spatially separated CoO_x and Au-Cu bimetallic cocatalysts. The ZnFe₂O₄@TiO₂ heterojunction and spatially separated dual cocatalysts can significantly promote the separation of photoinduced charge carriers. Combined with the unique hollow double-shell heterostructure characteristics and improved surface state properties, the hybrid nanospheres can efficiently adsorb and activate CO₂ molecules. These advantages cause the optimized catalyst to exhibit remarkably higher gas-phase photocatalytic CO₂ reduction activity than the control CoO_x/ZnFe₂O₄/Au-Cu and ZnFe₂O₄@H-TiO_2-x double-shell hollow nanospheres loaded with a single cocatalyst. Meanwhile, the Au-Cu bimetal effect boosts the CO₂ conversion rate and CH₄ selectivity. The optimized hybrid catalyst with a Au/Cu ratio of 1:1 provides a CH₄ yield of 21.39 μmol g^-1 h^-1 with 93.8% selectivity. This work provides a rational photocatalyst design to improve CO₂ conversion and CH₄ selectivity.

Enhanced photocatalytic activity of Bi2WO6 with PVP addition for CO2 reduction into ethanol under visible light

The conversion of CO₂ into new carbon-based products, such as fuels and chemicals, is an attractive and promising means of mitigating global energy needs and minimizing environmental damage. Although bismuth tungstate (Bi₂WO₆) as a photocatalyst can promote CO₂ photoreduction, a systematic study for the development of a low-cost and efficient catalyst is needed. Thus, Bi₂WO₆ with different morphologies was successfully synthesized using the hydrothermal method. An experimental design was applied to investigate the effect of synthesis time and PVP (polyvinylpyrrolidone) concentration on catalyst photocatalytic activity. Crystal structures, morphologies, optical absorption, and surface charges of the catalysts were characterized by X-ray diffraction, scanning electron microscope, UV-vis diffuse-reflection spectroscopy, nitrogen adsorption, and zeta potential. All samples exhibited good performance for the photoreduction of CO₂ into ethanol, and both time and PVP concentration were significant in the ethanol yield. Changes in synthesis conditions induced differences in catalyst characteristics, such as morphology, crystallinity, and, predominantly, surface area. Furthermore, PVP addition improved photocatalytic efficiency by up to 258% compared with results without the surfactant. The best sample, W-8h-10%, presented a flower-like morphology and ethanol yield of 68.9 μmol g^-1 h^-1.

Selective photocatalytic production of CH4 using Zn-based polyoxometalate as a nonconventional CO2 reduction catalyst

Efficient and selective production of CH₄ through the CO₂ reduction reaction (CO2RR) is a challenging task due to the high amount of energy consumption and various reaction pathways. Here, we report the synthesis of Zn-based polyoxometalate (ZnPOM) and its application in the photocatalytic CO2RR. Unlike conventional Zn-based catalysts that produce CO, ZnPOM can selectively catalyze the production of CH₄ in the presence of an Ir-based photosensitizer (TIr3) through the photocatalytic CO2RR. Photophysical and computation analyses suggest that selective photocatalytic production of CH₄ using ZnPOM and TIr3 can be attributed to (1) the exceptionally fast transfer of photogenerated electrons from TIr3 to ZnPOM through the strong molecular interactions between them and (2) effective transfer of electrons from ZnPOM to *CO intermediates due to significant hybridization of their molecular orbitals. This study provides insights into the design of novel CO2RR catalysts for CH₄ production beyond the limitations in conventional studies that focus on Cu-based materials.

Grain Boundary Engineering of Cu-Ag Thin-Film Catalysts for Selective (Photo)Electrochemical CO2 Reduction to CO and CH4

We investigated the relationship between grain boundary (GB) oxidation of Cu-Ag thin-film catalysts and selectivity of the (photo)electrochemical CO₂ reduction reaction (CO₂ RR). The change in the thickness of the Cu thin film accompanies the variation of GB density, and the Ag layer (3 nm) has an island-like morphology on the Cu thin film. Therefore, oxygen from ambient air penetrates into the Cu thin film through the GB of Cu and binds with it because the uncoordinated Cu atoms at the GBs are unstable. It was found that the Cu thin film with a small grain size was susceptible to spontaneous oxidation and degraded the faradaic efficiency (FE) of CO and CH₄. However, a relatively thick (≥80 nm) Cu layer was effective in preventing the GB oxidation and realized catalytic properties similar to those of bulk Cu-Ag catalysts. The optimized Cu (100 nm)-Ag (3 nm) thin film exhibited a unique bifunctional characteristic, which enables selective production of both CO (FE_CO = 79.8%) and CH₄ (FE_CH4 = 59.3%) at a reductive potential of -1.0 and -1.4 V_RHE, respectively. Moreover, the Cu-Ag thin film was used as a cocatalyst for photo-electrochemical CO₂ reduction by patterning the Cu-Ag thin film and a SiO₂ passivation layer on a p-type Si photocathode. This novel architecture improved the selectivity of CO and CH₄ under light illumination (100 mW/cm²).