Palladium-Based Electrocatalysts for Alcohol Oxidation in Half Cells and in Direct Alcohol Fuel Cells

Bimetallic PdCu Nanoparticles for Electrocatalysis: Multiphase or Homogeneous Alloy?

Crystal phase structure of bimetallic alloy is an important factor determining the electrocatalytic activity toward oxidation of energy molecules. In this paper, PdCu bimetallic NPs with similar element composition and different crystal phase structural features have been synthesized hydrothermally by adjusting the content of ethylenediaminetetraacetic acid disodium salt (EDTA-2Na). Multiphase PdCu NPs composed of pure Pd and alloy phase are obtained with a low concentration (even as low as zero) of EDTA-2Na in synthetic systems while homogeneous PdCu alloy NPs are formed in the presence of EDTA-2Na with a high concentration. The catalytic activity of ethanol electrooxidation is increased from 3.1 mA·cm^-2 of pure Pd NPs, to 3.6 mA·cm^-2 of multiphase PdCu NPs, and to 5.0 mA·cm^-2 of homogeneous PdCu alloy NPs (about 2360 mA mg_Pd^-1). The surface composition and structural stability of homogeneous PdCu NPs were much less damaged during electrochemical measurements. Based on the experimental data, the formation mechanism of multiphase and homogeneous PdCu NPs and their structure-property relationship have been discussed.

Atomically deviated Pd-Te nanoplates boost methanol-tolerant fuel cells

The methanol crossover effect in direct methanol fuel cells (DMFCs) can severely reduce cathodic oxygen reduction reaction (ORR) performance and fuel efficiency. As a result, developing efficient catalysts with simultaneously high ORR activity and excellent antipoisoning methanol capability remains challenging. Here, we report a class of Pd-Te hexagonal nanoplates (HPs) with a Pd20Te7 phase that simultaneously overcome the activity and methanol-tolerant issues in alkaline DMFC. Because of the specific arrangement of Pd atoms deviated from typical hexagonal close-packing, Pd-Te HPs/C displays extraordinary methanol tolerance with high ORR performance compared with commercial Pt/C. DFT calculations reveal that the high performance of Pd-Te HPs can be attributed to the breakthrough of the linear relationship between OOH* and OH* adsorption, which leaves sufficient room to improve the ORR activity but suppresses the methanol oxidation reaction. The concurrent high ORR activity and excellent methanol tolerance endow Pd-Te HPs as practical electrocatalysts for DMFC and beyond.

Promoting Effects of Au Submonolayer Shells on Structure-Designed Cu-Pd/Ir Nanospheres: Greatly Enhanced Activity and Durability for Alkaline Ethanol Electro-Oxidation

Rationally engineering the surface physicochemical properties of nanomaterials can improve their activity and durability for various electrocatalytic and energy conversion applications. Cu-Pd/Ir (CPI) nanospheres (NSs) anchored on N-doped porous graphene (NPG) [(CPI NSs/NPG)] have been recently demonstrated as a promising electrocatalyst for the alkaline ethanol oxidation reaction (EOR); to further enhance their electrocatalytic performance, the NPG-supported CPI NSs are coated with Au submonolayer (SML) shells (SMSs), through which their surface physicochemical properties can be tuned. CPI NSs/NPG is prepared by our previously developed method and possesses the special structures of composition-graded Cu₁Pd₁ and surface-doped Ir_0.03. The Au SMSs with designed surface coverages are formed via an electrochemical technology involving incomplete Cu underpotential deposition (UPD) and Au³⁺ galvanic replacement. A distinctive volcano-type relation between the EOR electrocatalytic activity and the Au-SMS surface coverage for CPI@Au_SML NSs/NPG is revealed, and the optimal CPI@Au_1/6ML NSs/NPG greatly surpasses commercial Pd/C and CPI NSs/NPG in electrocatalytic activity and noble metal utilization. More importantly, its electrocatalytic durability in 1 h chronoamperometric and 500-cycle potential cycling degradation tests is also significantly improved. According to detailed physicochemical characterizations, electrochemical analyses, and density functional theory calculations, the promoting effects of the Au SMS for enhancing the EOR electrocatalytic activity and durability of CPI NSs/NPG can be mainly attributed to the greatly weakened carbonaceous intermediate bonding and properly increased surface oxidation potential. This work also proposes a versatile and effective strategy to tune the surface physicochemical properties of metal-based nanomaterials via incomplete UPD and metal-cation galvanic replacement for advancing their electrocatalytic and energy conversion performance.

Intrinsic Effect of Carbon Supports on the Activity and Stability of Precious Metal Based Catalysts for Electrocatalytic Alcohol Oxidation in Fuel Cells: A Review

Electrocatalyst supports, in particular carbonaceous materials, play critical roles in the electrocatalytic activity and stability of precious metal group (PMG)-based catalysts such as Pt, Pd, and Au for the electrochemical alcohol oxidation reaction (AOR) of fuels such as methanol and ethanol in polymer electrolyte membrane fuel cells (PEMFCs). Carbonaceous supports such as high surface area carbon provide electronic contact throughout the catalyst layer, isolate PMG nanoparticles (NPs) to maintain high electrochemical surface area, and provide hydrophobic properties to avoid flooding of the catalyst layer by liquid water produced. Compared to high surface area carbon, PMG catalysts supported on 1D and 2D carbon materials such as graphene and carbon nanotubes show enhanced activity and durability due to the intrinsic effect of the underlying carbonaceous supports on the electronic states of PMG NPs. The modification of the electronic environment, in particular the d-band centers of PMG NPs, weakens the adsorption of AOR intermediates, facilitates breaking of the C-C bonds, and thus enhances the electrocatalytic activity of PMG catalysts. The doping of heteroatoms further facilitates the electrocatalytic activity for the AOR through the structural, bifunctional, and electronic effects, in addition to the enhanced dispersion of PMG NPs in the carbon support. The prospects for the development of effective PMG-based catalysts for high-performance alcohol-fuel-based PEMFCs is discussed.

Shewanella oneidensis MR-1 self-assembled Pd-cells-rGO conductive composite for enhancing electrocatalysis

Biosynthesized noble metal nanoparticles (NPs) as promising green catalysts for electrochemical application has invited a lot of attention. However, effective electron transfer between biosynthesized NPs and electrode remains a challenge due to the uncontrollable and poor conductive property of cell substrates. In this study, graphene oxide (GO) was introduced into a bio-Pd synthesis process governed by Shewanella oneidensis MR-1, which was demonstrated to be simultaneously reduced with Pd(II) and transformed to reduced GO (rGO), resulting in the formation of a Pd-cells-rGO composite. Compared to the control without rGO (Pd-cells), the electrochemical conductivity of Pd-cells-rGO composite increased from almost zero to 196 μS cm^-1, indicating the rGO facilities the electron transport across the composite. Electrochemical characterizations revealed the electrochemical active surface area (ECSA) of Pd in Pd-cells-rGO was enlarged by increasing the amount of rGO in the composite, clearly indicating that the conductive network created by rGO enable the Pd NPs receive electrons from electrode and become electrochemical active. A considerable enhancement of electrocatalytic activity was further confirmed for Pd-cells-rGO as indicated by 36.7- and 17.2-fold increase (Pd-cells-rGO with Pd/GO ratio of 5/1 vs Pd-cells) of steady state current density toward hydrogen evolution and nitrobenzene reduction at -0.7 V and -0.55 V vs Ag/AgCl, respectively. We also compared the electrocatalytic performance with MWCNTs hybrids Pd-cells-CNTs. It was found that the association of Pd, cells and rGO creates an interactive and synergistic environment to allow higher conductivity and catalytic activity under the same amount of carbon nanomaterial. The strategy developed in this work activates a highly reactive NPs and proposed a designable protocol for enhancing electrocatalytic activity of biocatalysts.

Synthesis of Palladium-Based Crystalline@Amorphous Core-Shell Nanoplates for Highly Efficient Ethanol Oxidation

Phase engineering of nanomaterials (PEN) offers a promising route to rationally tune the physicochemical properties of nanomaterials and further enhance their performance in various applications. However, it remains a great challenge to construct well-defined crystalline@amorphous core-shell heterostructured nanomaterials with the same chemical components. Herein, the synthesis of binary (Pd-P) crystalline@amorphous heterostructured nanoplates using Cu_{3- χ} P nanoplates as templates, via cation exchange, is reported. The obtained nanoplate possesses a crystalline core and an amorphous shell with the same elemental components, referred to as c-Pd-P@a-Pd-P. Moreover, the obtained c-Pd-P@a-Pd-P nanoplates can serve as templates to be further alloyed with Ni, forming ternary (Pd-Ni-P) crystalline@amorphous heterostructured nanoplates, referred to as c-Pd-Ni-P@a-Pd-Ni-P. The atomic content of Ni in the c-Pd-Ni-P@a-Pd-Ni-P nanoplates can be tuned in the range from 9.47 to 38.61 at%. When used as a catalyst, the c-Pd-Ni-P@a-Pd-Ni-P nanoplates with 9.47 at% Ni exhibit excellent electrocatalytic activity toward ethanol oxidation, showing a high mass current density up to 3.05 A mg_Pd ^-1 , which is 4.5 times that of the commercial Pd/C catalyst (0.68 A mg_Pd ^-1 ).

Synthesis of Pd-Pt Ultrathin Assembled Nanosheets as Highly Efficient Electrocatalysts for Ethanol Oxidation

Control over composition and morphology of nanocrystals (NCs) is significant to develop advanced catalysts applicable to polymer electrolyte membrane fuel cells and further overcome the performance limitations. Here, we present a facile synthesis of Pd-Pt alloy ultrathin assembled nanosheets (UANs) by regulating the growth behavior of Pd-Pt nanostructures. Iodide ions supplied from KI play as capping agents for the {111} plane to promote 2-dimensional (2D) growth of Pd and Pt, and the optimal concentrations of cetyltrimethylammonium chloride and ascorbic acid result in the generation of Pd-Pt alloy UANs in high yield. The prepared Pd-Pt alloy UANs exhibited the remarkable enhancement of the catalytic activity and stability toward ethanol oxidation reaction compared to irregular-shaped Pd-Pt alloy NCs, commercial Pd/C, and commercial Pt/C. Our results confirm that the Pd-Pt alloy composition and ultrathin 2D morphology offer high accessible active sites and favorable electronic structure for enhancing electrocatalytic activity.

Manipulation of Neighboring Palladium and Mercury Atoms for Efficient *OH Transformation in Anodic Alcohol Oxidation and Cathodic Oxygen Reduction Reactions

The synergetic effect of neighboring heterogeneous atoms is capable of enabling unexpected catalytic performance, and the design of a well-ordered atomic structure and elaborating the underlying interactions are crucial for the development of superior electrocatalysts in fuel cells. We demonstrate here that an ordered Pd-Hg intermetallic alloy with dimensions of several nanometers can be subtly manipulated using a mild wet-chemical reduction approach. On the basis of combined results of XPS and HAADF-STEM analysis, the adjacent regions of metallic atoms were found to be evenly occupied by heterogeneous elements from the distribution features of the surface structure. Due to charge transfer from Hg to neighboring Pd, the down-shift of the d-band center in PdHg alloys was theoretically beneficial for desorption of crucial intermediates (*OH), both in anodic ethanol oxidation reaction (EOR) and in cathodic oxygen reduction reaction (ORR). In the presence of Hg atoms with lower *OH desorption energy, the rapid dissociation of *OH from Pd facilitated the final H₂O formation, with superior ORR efficiency comparable to Pt/C catalysts. Remarkably, the rapid combination of *OH on Hg atoms with CH₃CO* on neighboring Pd atoms unambiguously favored generation of acetate ions (rate-determining) in the catalytic EOR process, resulting in a high mass activity (7.68 A per mgPd). This well-ordered atomic structure also shows excellent long-term stability in ethylene glycol oxidation reaction and ORR.

Spin Regulation on 2D Pd-Fe-Pt Nanomeshes Promotes Fuel Electrooxidations

Spin engineering provides a powerful strategy for manipulating the interaction between electrons in the d orbital and oxygen-containing adsorbates, while a little endeavor was performed to understand whether such a strategy can make a prosperous enhancement for fuel electrooxidations. Herein, we demonstrate that spin engineering of trimetallic Pd-Fe-Pt nanomeshes (NMs) can achieve superior enhancement for fuel electrooxidations. Magnetization characterizations reveal that Pd₅₉Fe₂₇Pt₁₄ NMs own the highest number of polarized spins (μ_b = 0.85 μB/f.u.), playing an important role on facilitating the adsorption of OH_ads to promote the oxidation of CO_ads, as confirmed by theoretical results. Consequently, the optimized Pd₅₉Fe₂₇Pt₁₄ NMs exhibit excellent methanol oxidation reaction activity and stability with a mass activity of 1.61 A mg_Pt^-1, 2.6-fold and 7.3-fold larger than those of PtRu/C and Pt/C. Such catalysts also present exceptional performances in ethanol oxidation and formic acid oxidation reactions. Our work highlights a new strategy for designing efficient electrocatalysts for fuel electrooxidations and beyond.

Pd/MXene(Ti3C2Tx)/reduced graphene oxide hybrid catalyst for methanol electrooxidation

A key challenge in developing direct methanol fuel cells is the fabrication of electrocatalysts with high activity and long durability. Herein, we report a performance enhanced electrocatalyst of nanoscale Pd on MXene (Ti₃C₂T_x) and reduced graphene oxide (rGO). The mass activity of Pd/Ti₃C₂T_x-rGO (1: 1) hybrid toward methanol oxidation reaction is 753 mA mg^-1, which is 1.7 times than that of Pd/C (446 mA mg^-1). Additionally, the current density of Pd/Ti₃C₂T_x-rGO (1:1) catalyst contains 212 mAmg^-1 which is nine times higher than that of Pd/C (23 mA mg^-1) after 7200 s. The Pd/Ti₃C₂T_x-rGO (1:1) catalyst exhibits excellent cycling stability and long-term life. These remarkable catalytic performances are attributed to the role of Ti₃C₂T_x and rGO in enhancing the catalytic activity surface area and rapid mass/charge transfer due to the synergistic effect between Pd and Ti₃C₂T_x/rGO.

Bimetallic alloy and semiconductor support synergistic interaction effects for superior electrochemical catalysis

The design and fabrication of economically viable anode catalysts for the methanol oxidation reaction (MOR) have been challenging issues in direct methanol fuel cells (DMFCs) over the decades. In this work, a composite electrochemical catalyst of Pd-coupled Ag and ZnO for the possible replacement of expensive Pt catalysts in DMFCs is successfully prepared. The as-made Pd@Ag/ZnO exhibits specific activity, which is 1.8-fold, 2.8-fold, and 4.6-fold higher than that of a Pd/ZnO catalyst, 20% Pd/C catalyst and Pd black, respectively. The improvement of the catalytic mechanism is likely due to the synergistic interaction between Pd@Ag and ZnO. The density functional theory (DFT) calculation results confirm that Ag doped into Pd weakens the adsorption of CO, dramatically improving the capability to resist CO poisoning.

CaO-Promoted Graphene-Supported Palladium Nanocrystals as a Universal Electrocatalyst for Direct Liquid Fuel Cells

Here, we present the fabrication of a reduced graphene oxide-supported PdCa (PdCa/rGO) alloyed catalyst via a NaBH₄ reduction method for direct alcohol fuel cells in basic medium and direct formic acid fuel cells in acidic medium. Powder X-ray diffraction, energy-dispersive X-ray spectroscopy, scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, Brunauer-Emmett-Teller, inductively coupled plasma mass spectrometry, and Raman spectroscopy are used to characterize the PdCa/rGO catalyst. We proved that the calcium oxide significantly enhances the electrocatalytic methanol, ethanol, and formic acid oxidation over the Pd/rGO surface. The obtained mass activities for PdCa/rGO are 4838.06, 4674.70, and 3906.49 mA mg^-1 for formic acid, methanol, and ethanol, respectively. Long-term stability, high activity, and high level of tolerance to CO poisoning of the PdCa/rGO electrocatalyst are attributed to the presence of calcium oxide. These results prove that the PdCa/rGO catalyst has improved electrocatalytic performance for the oxidation of formic acid, methanol, and ethanol with reference to the Pd/rGO.

Green dual-template synthesis of AgPd core-shell nanoparticles with enhanced electrocatalytic activity

A key challenge in developing an ethanol oxidation reaction is nontoxic fabrication of highly active stable and low-cost catalysts. Here we design a green synthetic strategy of AgPd bimetallic nanosphere by a dual-template cascade method. The Pd nanoshell is firstly prepared using Vapreotide acetate as a primary template, and then the Ag nanoshell acts as a secondary template for the distribution of AgPd alloy nanoparticles. The AgPd nanoparticles have core-shell structures and various sizes, and their shell thicknesses are tuned by controlling the amount of PdCl₂. The six different samples are prepared, named AgPd-1, AgPd-2, AgPd-3, AgPd-4, AgPd-5, and AgPd-6, respectively. The mass current density of AgPd-5, is higher 3.87 times that of commercial Pd/C, and exhibits the best ethanol oxidation reaction activity and long-term stability. The main reasons are that the AgPd-5 possessed excellent specific surface area due to their rough structure, and Ag can remove more CO-like species. This is the first time a Vapreotide acetate/Ag-template method has been used to synthesize a AgPd core-shell structure, which would have broad application prospects for direct ethanol fuel cells.

Alkaline Ethanol Oxidation Reaction on Carbon Supported Ternary PdNiBi Nanocatalyst using Modified Instant Reduction Synthesis Method

Direct ethanol fuel cells (DEFC) still lack active and efficient electrocatalysts for the alkaline ethanol oxidation reaction (EOR). In this work, a new instant reduction synthesis method was developed to prepare carbon supported ternary PdNiBi nanocatalysts with improved EOR activity. Synthesized catalysts were characterized with a variety of structural and compositional analysis techniques in order to correlate their morphology and surface chemistry with electrochemical performance. The modified instant reduction synthesis results in well-dispersed, spherical Pd₈₅Ni₁₀Bi₅ nanoparticles on Vulcan XC72R support (Pd₈₅Ni₁₀Bi₅/C^(II-III)), with sizes ranging from 3.7 ± 0.8 to 4.7 ± 0.7 nm. On the other hand, the common instant reduction synthesis method leads to significantly agglomerated nanoparticles (Pd₈₅Ni₁₀Bi₅/C^(I)). EOR activity and stability of these three different carbon supported PdNiBi anode catalysts with a nominal atomic ratio of 85:10:5 were probed via cyclic voltammetry and chronoamperometry using the rotating disk electrode method. Pd₈₅Ni₁₀Bi₅/C^(II) showed the highest electrocatalytic activity (150 mA⋅cm⁻²; 2678 mA⋅mg⁻¹) with low onset potential (0.207 V) for EOR in alkaline medium, as compared to a commercial Pd/C and to the other synthesized ternary nanocatalysts Pd₈₅Ni₁₀Bi₅/C^(I) and Pd₈₅Ni₁₀Bi₅/C^(III). This new synthesis approach provides a new avenue to developing efficient, carbon supported ternary nanocatalysts for future energy conversion devices.

Graphical Abstract

Development of advanced materials for cleaner energy generation through fuel cells

The use of fuel cells in the transportation sector holds promise as a sustainable option for the generation of cleaner energy along with cumulative lesser GHG emissions.

Significant promotion effects of Ag oxide towards Pd catalysis for ethanol and methanol oxidation reactions

Ag oxides play a crucial role in promoting the catalysis of Pd both for ethanol and methanol oxidation reactions.

Recent advances in the electrooxidation of biomass-based organic molecules for energy, chemicals and hydrogen production

The recent developments in biomass-derivative fuelled electrochemical converters for electricity or hydrogen production together with chemical electrosynthesis have been reviewed.

Highly branched and defect-rich PdP nanosheets for ethanol oxidation electrocatalysis

Highly branched, defect-rich, and ultrathin PdP alloy nanosheets with enhanced electrocatalytic ethanol oxidation reaction (EOR) performance.

Engineering the Metal/Oxide Interface of Pd Nanowire@CuOx Electrocatalysts for Efficient Alcohol Oxidation Reaction

The development of new type electrocatalysts with promising activity and antipoisoning ability is of great importance for electrocatalysis on alcohol oxidation. In this work, Pd nanowire (PdNW)/CuO_x heterogeneous catalysts with different types of PdOCu interfaces (Pd/amorphous or crystalline CuO_x ) are prepared via a two-step hydrothermal strategy followed by an air plasma treatment. Their interface-dependent performance on methanol and ethanol oxidation reaction (MOR and EOR) is clearly observed. The as-prepared PdNW/crystalline CuO_x catalyst with 17.2 at% of Cu on the PdNW surface exhibits better MOR and EOR activity and stability, compared with that of PdNW/amorphous CuO_x and pristine PdNW catalysts. Significantly, both the cycling tests and the chronoamperometric measurements reveal that the PdNW/crystalline CuO_x catalyst yields excellent tolerance toward the possible intermediates including formaldehyde, formic acid, potassium carbonate, and carbon monoxide generated during the MOR process. The detailed analysis of their chemical state reveals that the enhanced activity and antipoison ability of the PdNW/crystalline CuO_x catalyst originates from the electron-deficient Pd^δ+ active sites which gradually turn into Pd₅ O₄ species during the MOR catalysis. The Pd₅ O₄ species can likely be stabilized by moderate crystalline CuO_x decorated on the surface of PdNW due to the strong PdOCu interaction.

Synthesis of PdM (M = Zn, Cd, ZnCd) Nanosheets with an Unconventional Face-Centered Tetragonal Phase as Highly Efficient Electrocatalysts for Ethanol Oxidation

Recently, crystal-phase engineering has been emerging as a promising strategy to tune the physicochemical properties of noble metal catalysts and further improve their catalytic performance. However, the synthesis of noble metal catalysts with an unconventional crystal phase as well as desired composition and morphology still remains a great challenge. Herein, a series of PdM (M = Zn, Cd, ZnCd) nanosheets (NSs) with thickness less than 5 nm have been synthesized via a facile one-pot wet-chemical method. In particular, different from the conventional face-centered cubic (fcc) phase, PdM NSs possess an unconventional face-centered tetragonal (fct) phase. As a proof-of-concept application, the fct PdZn NSs exhibit significantly enhanced mass activity and stability in ethanol oxidation reaction, compared to the pure Pd NSs and commercial Pd black catalyst.

Activity Origin and Design Principles for Oxygen Reduction on Dual-Metal-Site Catalysts: A Combined Density Functional Theory and Machine Learning Study

Dual-metal-site catalysts (DMSCs) are emerging as a new frontier in the field of oxygen reduction reaction (ORR). However, there is a lack of design principles to provide a universal description of the relationship between intrinsic properties of DMSCs and the catalytic activity. Here, we identify the origin of ORR activity and unveil design principles for graphene-based DMSCs by means of density functional theory computations and machine learning (ML). Our results indicate that several experimentally unexplored DMSCs can show outstanding ORR activity surpassing that of platinum. Remarkably, our ML study reveals that the ORR activity of DMSCs is intrinsically governed by some fundamental factors, such as electron affinity, electronegativity, and radii of the embedded metal atoms. More importantly, we propose predictor equations with acceptable accuracy to quantitatively describe the ORR activity of DMSCs. Our work will accelerate the search for highly active DMSCs for ORR and other electrochemical reactions.

Ultrafine PtCuRh nanowire catalysts with alleviated poisoning effect for efficient ethanol oxidation

As a green power source, direct ethanol fuel cells (DEFCs) have broad application prospects. However, most catalysts of DEFCs still exhibit defects, such as the difficulty of C-C bond cleavage, serious CO poisoning and limited catalytic activity. Here, we report ultrafine PtCuRh nanowires (NWs) with outstanding anti-CO-poisoning properties and enhanced activity. The average diameter of the ultrafine PtCuRh NWs is about 1.49 nm, effectively improving the atomic utilization efficiency (UE) of platinum. Owing to the combination of an ultrafine nanostructure, good electronic interaction and the high UE of Pt atoms, the optimized ultrafine PtCuRh NWs/C display superior electrocatalytic activity and stability compared with commercial Pt/C for the ethanol oxidation reaction (EOR). More importantly, further electrochemical results demonstrate that the incorporation of Rh is beneficial for enhancing the antipoisoning capability for some CO-like intermediates. Meanwhile, the synthetic method in this report is robust and universal, and can also be applied to the synthesis of ultrafine trimetallic PtCuPd and PtCuIr nanowires.

Synthesis of low- and high-index faceted metal (Pt, Pd, Ru, Ir, Rh) nanoparticles for improved activity and stability in electrocatalysis

Driven by the quest for future energy solution, faceted metal nanoparticles are being pursued as the next generation electrocatalysts for renewable energy applications. Thanks to recent advancement in solution phase synthesis, different low- and high-index facets on metal nanocrystals become accessible and are tested for specific electrocatalytic reactions. This minireview summarises the key approaches to prepare nanocrystals containing the most catalytically active platinum group metals (Pt, Pd, Ru, Ir and Rh) exposed with low- and high-index facets using solution phase synthesis. Electrocatalytic studies related to the different facets are highlighted to emphasise the importance of exposing facets for catalysing these reactions, namely oxygen reduction reaction (ORR), hydrogen oxidation reaction (HOR), alcohol oxidation including methanol (MOR) and ethanol oxidation reactions (EOR), formic acid oxidation reaction (FAOR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). The future outlook discusses the challenges and opportunities for making electrocatalysts that are even more active and stable.

Synthesis, growth mechanisms, and applications of palladium-based nanowires and other one-dimensional nanostructures

Palladium-based nanostructures have attracted the attention of researchers due to their useful catalytic properties and unique ability to form hydrides, which finds application in hydrogen storage and hydrogen detection. Palladium-based nanowires have some inherent advantages over other Pd nanomaterials, combining high surface-to-volume ratio with good thermal and electron transport properties, and exposing high-index crystal facets that can have enhanced catalytic activity. Over the past two decades, both synthesis methods and applications of 1D palladium nanostructures have advanced greatly. In this review, we start by discussing different types of 1D palladium nanostructures before moving on to the different synthesis approaches that can produce them. Next, we discuss factors including kinetic vs. thermodynamic control of growth, oxidative etching, and surface passivation that affect palladium nanowire synthesis. We also review efforts to gain insight into growth mechanisms using different characterization tools. We discuss the effects of concentration of capping agents, reducing agents, metal halides, pH, and sacrificial oxidation on the growth of Pd-based nanowires in solution, from shape control, to yield, to aspect ratio. Various applications of palladium and palladium alloy nanowires are then discussed, including electrocatalysis, hydrogen storage, and sensing of hydrogen and other chemicals. We conclude with a summary and some perspectives on future research directions for this category of nanomaterials.

Electrocatalytic Oxidation of Ethanol on the Surface of Graphene Based Nanocomposites: An Introduction and Review to it in Recent Studies

This review gives an overview of the electrochemical investigations about the properties of various types of graphene composites in the ethanol oxidation. Various routes to provide appropriate graphene-based materials required electrochemical techniques for investigation of different types of the materials as well as their performance and efficacy in ethanol oxidation are discussed in detail. Furthermore, it is demonstrated that the incorporation of suitable materials, e. g. noble metals (graphene-supported binary and ternary metal nanoparticles), metal oxides, conductive polymer, etc, with graphene results in excellent electrocatalytic activity, superb durability and selectivity in ethanol oxidation. Immobilization of electrocatalytically active NPs on graphene supports using physical approaches is considered as an effective route to prepare direct ethanol fuel cell (DEFC) anode catalysts.

Defect Engineering of Palladium-Tin Nanowires Enables Efficient Electrocatalysts for Fuel Cell Reactions

The defect engineering of noble metal nanostructures is of vital importance because it can provide an additional yet advanced tier to further boost catalysis, especially for one-dimensional (1D) noble metal nanostructures with a high surface to bulk ratio and more importantly the ability to engineer the defect along the longitudinal direction of the 1D nanostructures. Herein, for the first time, we report that the defect in 1D noble metal nanostructures is a largely unrevealed yet essential factor in achieving highly active and stable electrocatalysts toward fuel cell reactions. The detailed electrocatalytic results show that the Pd-Sn nanowires (NWs) exhibit interesting defect-dependent performance, in which the defect-rich Pd₄Sn wavy NWs display the highest activity and durability for both the methanol oxidation reaction (MOR) and the oxygen reduction reaction (ORR). Density functional theory (DFT) calculations reveal that a large number of surface vacancies/agglomerated voids are the driving forces for forming surface grain boundaries (GBs) within Pd₄Sn WNWs. These electronic active GB regions are the key factors in preserving the number of Pd⁰ sites, which are critical for minimizing the intrinsic site-to-site electron-transfer barriers. Through this defect engineering, the Pd₄Sn WNWs ultimately yield highly efficient alkaline ORR and MOR. The present work highlights the importance of defect engineering in boosting the performance of electrocatalysts for potentially practical fuel cells and energy applications.

Theoretical investigation of the ORR on boron-silicon nanotubes (B-SiNTs) as acceptable catalysts in fuel cells

Here, the potential of boron doped silicon nanotubes (7, 0) as ORR catalysts is examined. Acceptable paths for the ORR on studied catalysts are examined through DFT. The optimum mechanism of the ORR on the surface of B2-SiNT (7, 0) is shown. The ORR on the surface of B2-SiNTs (7, 0) can continue through LH and ER mechanisms. The calculated beginning voltage for the ORR on B2-SiNTs (7, 0) is 0.37 V and it is smaller than the beginning voltage (0.45 V) for platinum-based catalysts. In the acidic solution the beginning voltage for the oxygen reduction process can be evaluated to be 0.97 V, which corresponds to 0.37 V as a minimum overvoltage for the ORR. The B2-SiNTs (7, 0) are suggested as an ORR catalyst in acidic environments.

Insights into Compositional and Structural Effects of Bimetallic Hollow Mesoporous Nanospheres toward Ethanol Oxidation Electrocatalysis

A one-pot soft-templating method is reported to fabricate nanosized bimetallic PdAg hollow mesoporous nanospheres (HMSs) for electrocatalytic ethanol oxidation reaction (EOR). The synthesis relies on the "dual-template" surfactant of dioctadecyldimethylammonium chloride that drives in situ growth of mesoporous frameworks on the surface of vesicles into the HMSs with radially opened mesochannels. The synthetic protocol is extendable to engineer elemental compositions and hierarchical nanostructures of PdAg nanoalloys. This system thus provides a direct yet solid platform to understand catalytic add-in synergies of PdAg HMSs toward electrochemical EOR. By evaluating compositional and structural features separately, bimetallic Pd₆₅Ag₃₅ HMSs display the highest EOR activity with a mass activity of 4.61 A mg_Pd^-1. Mechanism studies indicate that synergistically electronic and bifunctional effects as well as structural advantages of Pd₆₅Ag₃₅ HMSs kinetically optimize the removal of poisoning carbonaceous intermediates and accelerate the diffusion processes (the rate-determining step), and thus promote the EOR performance accordingly.

Ethanol Electrooxidation Catalyzed by Tungsten Core@Palladium Shell Nanoparticles

Bimetallic nanostructures represent effective electrocatalysts toward a number of important reactions. In the present study, carbon-supported palladium-tungsten alloy nanoparticles with a quasi-tungsten core@palladium shell structure (W@Pd/C) were synthesized by a galvanic replacement reaction of amorphous tungsten nanoparticles with Pd(II) at different temperatures (0, 25, and 50 °C), and exhibited apparent electrocatalytic activity toward ethanol oxidation reaction (EOR). When the sample was prepared at 0 °C, large amorphous tungsten nanoparticles were etched off and much smaller W@Pd nanoparticles were formed and dispersed rather evenly on the carbon surface whereas at higher reaction temperatures (25 and 50 °C), the W@Pd nanoparticles became agglomerated. The structures of the obtained samples were characterized by a range of experimental tools, including (scanning) transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical methods. Among the series, the W@Pd/C sample prepared at 0 °C was observed to exhibit the best EOR performance, with a mass activity (9535.5 mA mg_Pd^-1) over three times better than that of commercial Pd/C and markedly enhanced stability.

Electrocatalytic Oxidation of Methanol, Ethanol, and Glycerol on Ni(OH)2 Nanoparticles Encapsulated with Poly[Ni(salen)] Film

This study describes a systematic investigation of the electrocatalytic activity of poly[Ni(salen)] films, as catalysts for the electro-oxidation of Cn alcohols (Cn = methanol, ethanol, and glycerol) in alkaline medium. The [Ni(salen)] complex was electropolymerized on a glassy carbon surface and electrochemically activated in NaOH solution by cyclic voltammetry. X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy results indicate that during the activation step the polymeric film hydrolyzes, leading to the formation of β-Ni(OH)₂ spherical nanoparticles, with an average size of 2.4 ± 0.5 nm, encapsulated with the poly[Ni(salen)] film. Electrochemical results obtained together with the in situ Fourier transform infrared spectroscopy confirm that the electro-oxidation of methanol, ethanol, and glycerol occurs by involving a cycling oxidation of β-Ni(OH)₂ with the formation of β-NiOOH species, followed by the charge transfer to the alcohols, which regenerates β-Ni(OH)₂. Analyses of the oxidation products at low potentials indicate that the major product obtained during the oxidation of methanol and glycerol is the formate, while the oxidation of ethanol leads to the formation of acetate. On the other hand, at high potentials (E = 0.6 V), there is evidence that the oxidation of Cn alcohols leads to carbonate ions as an important product.