Synthesis of Thermally Sensitive Water-Soluble Polymethacrylates by Living Anionic Polymerizations of Oligo(ethylene glycol) Methyl Ether Methacrylates

Hybrid micellar hydrogels of a thermosensitive ABA triblock copolymer and hairy nanoparticles: effect of spatial location of hairy nanoparticles on gel properties

This article reports a method for control of spatial location of nanoparticles (NPs) in hybrid micellar hydrogels of a thermosensitive ABA triblock copolymer and polymer brush-grafted NPs (hairy NPs), either inside or outside the core of micelles, and the study of the effect of different locations of NPs on gel properties. Two batches of thermosensitive polymer brush-grafted, 17 nm silica NPs with different lower critical solution temperatures (LCSTs) and a thermosensitive ABA triblock copolymer composed of a poly(ethylene oxide) central block and thermosensitive outer blocks (ABA-D) were synthesized. The different locations of NPs were achieved by controlling the LCST of hairy NPs (LCST(NP)) relative to that of the thermosensitive outer blocks of ABA-D (LCST(ABA)). When the LCST(NP) and LCST(ABA) were similar, the NPs resided in the core of micelles upon heating from below the LCST(NP) and LCST(ABA). When the LCST(NP) was significantly higher, the NPs were located outside the core of micelles as confirmed by fluorescent resonance energy transfer. The effects of different locations of hairy NPs and NP-to-polymer mass ratio on properties of hybrid micellar hydrogels formed from aqueous solutions of ABA-D with a concentration of 10 wt % and various amounts of hairy NPs were studied by rheological measurements. The sol-gel transition temperature (T(sol-gel)) and dynamic storage modulus G' of the gels with NPs inside the core of micelles did not change much with increasing the NP-to-polymer mass ratio. In contrast, the T(sol-gel) of gels with NPs in the interstitial space among micelles increased slightly and the G' decreased significantly with the increase of the NP-to-polymer ratio. The hairy NPs in the interstitial space appeared to affect the formation of polymer networks and increase the fraction of polymer loops, resulting in a lower density of bridging chains and thus a lower G'. In addition, for gels with NPs in the interstitial space, a noticeable increase in G' was observed in the heating ramps above 40 °C, which was likely caused by the collapsed hairy NPs adsorbing polymer chains in the dangling and loop forms, increasing the density of bridging chains.

High interfacial activity of polymers "grafted through" functionalized iron oxide nanoparticle clusters

The mechanism by which polymers, when grafted to inorganic nanoparticles, lower the interfacial tension at the oil-water interface is not well understood, despite the great interest in particle stabilized emulsions and foams. A simple and highly versatile free radical "grafting through" technique was used to bond high organic fractions (by weight) of poly(oligo(ethylene oxide) monomethyl ether methacrylate) onto iron oxide clusters, without the need for catalysts. In the resulting ∼1 μm hybrid particles, the inorganic cores and grafting architecture contribute to the high local concentration of grafted polymer chains to the dodecane/water interface to produce low interfacial tensions of only 0.003 w/v % (polymer and particle core). This "critical particle concentration" (CPC) for these hybrid inorganic/polymer amphiphilic particles to lower the interfacial tension by 36 mN/m was over 30-fold lower than the critical micelle concentration of the free polymer (without inorganic cores) to produce nearly the same interfacial tension. The low CPC is favored by the high adsorption energy (∼10(6) kBT) for the large ∼1 μm hybrid particles, the high local polymer concentration on the particles surfaces, and the ability of the deformable hybrid nanocluster cores as well as the polymer chains to conform to the interface. The nanocluster cores also increased the entanglement of the polymer chains in bulk DI water or synthetic seawater, producing a viscosity up to 35,000 cP at 0.01 s(-1), in contrast with only 600 cP for the free polymer. As a consequence of these interfacial and rheological properties, the hybrid particles stabilized oil-in-water emulsions at concentrations as low as 0.01 w/v %, with average drop sizes down to 30 μm. In contrast, the bulk viscosity was low for the free polymer, and it did not stabilize the emulsions. The ability to influence the interfacial activity and rheology of polymers upon grafting them to inorganic particles, including clusters, may be expected to be broadly applicable to stabilization of emulsions and foams.

RAFT polymerization of temperature- and salt-responsive block copolymers as reversible hydrogels

Reversible-addition fragmentation chain transfer (RAFT) polymerization enabled the synthesis of novel, stimuli-responsive, AB and ABA block copolymers. The B block contained oligo(ethylene glycol) methyl ether methacrylate (OEG) and was permanently hydrophilic in the conditions examined. The A block consisted of diethylene glycol methyl ether methacrylate (DEG) and [2-(methacryloyloxy)ethyl]trimethylammonium chloride (TMA). The A block displayed both salt- and temperature-response with lower critical solution temperatures (LCSTs) dependent on the molar content of TMA and the presence of salt. Higher TMA content in the AB diblock copolymers increased the critical micelle temperatures (CMT) in HPLC-grade water due to an increased hydrophilicity of the A block. Upon addition of 0.9 wt% NaCl, the CMTs of poly(OEG-b-DEG₉₅TMA₅) decreased from 50 °C to 36 °C due to screening of electrostatic repulsion between the TMA units. ABA triblock copolymers displayed excellent hydrogel properties with salt- and temperature-dependent gel points. TMA incorporation in the A block increased the gel points for all triblock copolymers, and salt-response increased with higher TMA composition in the A block. For example, poly(DEG₉₈TMA₂-b-OEG-b-DEG₉₈TMA₂) formed a hydrogel at 40 °C in HPLC-grade water and 26 °C in 0.9 wt% NaCl aqueous solution. These salt- and temperature-responsive AB diblock and ABA triblock copolymers find applications as drug delivery vehicles, adhesives, and hydrogels.

Morphing hydrogel patterns by thermo-reversible fluorescence switching

Stimuli responsive surfaces that show reversible fluorescence switching behavior in response to temperature changes were fabricated. Oligo(ethylene glycol) methacrylate thermoresponsive polymers with amine end-groups were prepared by atom transfer radical polymerization (ATRP). The polymers were patterned on silicon surfaces by electron beam (e-beam) lithography, followed by conjugation of self-quenching fluorophores. Fluorophore conjugated hydrogel thin films were bright when the gels were swollen; upon temperature-induced collapse of the gels, self-quenching of the fluorophores led to significant attenuation of fluorescence. Importantly, the fluorescence was regained when the temperature was cooled. The fluorescence switching behavior of the hydrogels for up to ten cycles was investigated and the swelling-collapse was verified by atomic force microscopy. Morphing surfaces that change shape several times upon increase in temperature were obtained by patterning multiple stimuli responsive polymers.

Tertiary-amine-containing thermo- and pH-sensitive hydrophilic ABA triblock copolymers: effect of different tertiary amines on thermally induced sol-gel transitions

This Article reports on the synthesis of a series of well-defined, tertiary-amine-containing ABA triblock copolymers, composed of a poly(ethylene oxide) (PEO) central block and thermo- and pH-sensitive outer blocks, and the study of the effect of different tertiary amines on thermally induced sol-gel transition temperatures (T(sol-gel)) of their 10 wt % aqueous solutions. The doubly responsive ABA triblock copolymers were prepared from a difunctional PEO macroinitiator by atom transfer radical polymerization of methoxydi(ethylene glycol) methacrylate and ethoxydi(ethylene glycol) methacrylate at a feed molar ratio of 30:70 with ∼5 mol % of either N,N-diethylaminoethyl methacrylate (DEAEMA), N,N-diisopropylaminoethyl methacrylate, or N,N-di(n-butyl)aminoethyl methacrylate. The chain lengths of thermosensitive outer blocks and the molar contents of tertiary amines were very similar for all copolymers. Using rheological measurements, we determined the pH dependences of T(sol-gel) of 10 wt % aqueous solutions of these copolymers in a phosphate buffer. The T(sol-gel) versus pH curves of all polymers exhibited a sigmoidal shape. The T(sol-gel) increased with decreasing pH; the changes were small on both high and low pH sides. At a specific pH, the T(sol-gel) decreased with increasing the hydrophobicity of the tertiary amine, and upon decreasing pH the onset pH value for the T(sol-gel) to begin to increase noticeably was lower for the more hydrophobic tertiary amine-containing copolymer. In addition, we studied the effect of different tertiary amines on the release behavior of FITC-dextran from 10 wt % micellar gels in an acidic medium at 37 and 27 °C. The release profiles for three studied hydrogels at 37 °C were essentially the same, suggesting that the release was dominated by the diffusion of FITC-dextran. At 27 °C, the release was significantly faster for the DEAEMA-containing copolymer, indicating that both diffusion and gel dissolution contributed to the release at this temperature.

Synthesis and encapsulation of an amphiphilic thermoresponsive star polymer with β-cyclodextrin and hyperbranched poly(oligo(ethylene glycol)methacrylate) as building blocks

Schematic illustrations of the thermally-induced self-assembly and possible encapsulation behaviors with single or multi-guests for PE-CD–POEGMAS.

Tuning the critical gelation temperature of thermo-responsive diblock copolymer worm gels

Tuning the thermo-responsive behavior of statistical diblock copolymer worms.

Thermoresponsive properties of 3-, 4-, 6-, and 12-armed star-shaped poly[2-(dimethylamino)ethyl methacrylate]s prepared by core-first group transfer polymerization

The thermoresponsive behavior of a variety of star-shaped poly[2-(dimethylamino)ethyl methacrylate]s was intensively investigated by evaluating the effect of mass concentration in aqueous solution, molecular weight, or arm number of the polymers on their cloud points.

Thiol–ene “click” reactions and recent applications in polymer and materials synthesis: a first update

This contribution serves as an update to a previous review (Polym. Chem.2010,1, 17–36) and highlights recent applications of thiol–ene ‘click’ chemistry as an efficient tool for both polymer/materials synthesis as well as modification.

Dual-temperature and pH responsive (ethylene glycol)-based nanogels via structural design

Dual-temperature and pH responsive (ethylene glycol)-based nanogels were synthesized. Both the core and the shell of the nanogels showed a lower critical solution temperature (LCST) and the LCST of the shell was strongly affected by the solution pH and salt concentration due to the presence of carboxylic acid groups at the nanogel surface.

Pseudo-graft polymer based on adamantyl-terminated poly(oligo(ethylene glycol) methacrylate) and homopolymer with cyclodextrin as pendant: its thermoresponsivity through polymeric self-assembly and host–guest inclusion complexation

Thermoresponsivity and self-assembly of a pseudo-graft polymer based on Ad-terminated poly(oligo(ethylene glycol) methacrylate) and homopolymer with CD pendants.

A pH and thermosensitive choline phosphate-based delivery platform targeted to the acidic tumor microenvironment

Solid tumors generally exhibit an acidic microenvironment which has been recognized as a potential route to distinguishing tumor from normal tissue for purposes of drug delivery or imaging. To this end we describe a pH and temperature sensitive polymeric adhesive that can be derivatized to carry drugs or other agents and can be tuned synthetically to bind to tumor cells at pH 6.8 but not at pH 7.4 at 37 °C. The adhesive is based on the universal reaction between membrane phosphatidyl choline (PC) molecules and polymers derivatized with multiple copies of the inverse motif, choline phosphate (CP). The polymer family we use is a linear copolymer of a CP terminated tetraethoxymethacrylate and dimethylaminoethyl (DMAE) methacrylate, the latter providing pH sensitivity. The copolymer exhibits a lower critical solution temperature (LCST) just below 37 °C when the DMAE is uncharged at pH 7.4 but the LCST does not occur when the group is charged at pH 6.8 due to the ionization hydrophilicity. At 37 °C the polymer binds strongly to mammalian cells at pH 6.8 but does not bind at pH 7.4, potentially targeting tumor cells existing in an acidic microenvironment. We show the binding is strong, reversible if the pH is raised and is followed rapidly by cellular uptake of the fluorescently labeled material. Drug delivery utilizing this dually responsive family of polymers should provide a basis for targeting tumor cells with minimal side reactions against untransformed counterparts.

Temperature and pH dual-responsive POEGMA-based coatings for protein adsorption

Poly(oligo(ethylene glycol)ethyl ether methacrylate (POEGMA246) coatings were successfully fabricated using novel approach via polymerization from oligoperoxide grafted to premodified glass substrate. Wettability, content and composition of coatings fabricated with different polymerization times were determined using contact angle measurements, ellipsometry and Time of Flight-Secondary Ion Mass Spectrometry (TOF-SIMS). Thermo- and pH-responsive properties of POEGMA246 coatings were found to depend significantly on concentration of the grafted POEGMA246. Coatings fabricated with polymerization time 30 h exhibit not only temperature- but also pH-dependence of wettability. Thermal response of wettability, measured between 20 and 32°C, was prominent at pH 9 and 7 and diminished or was absent at pH 5 and 3, indicating a transition between hydrated loose coils and hydrophobic collapsed chains, blocked at low pH. Protein adsorption, observed by fluorescence microscopy and analyzed semi-quantitatively using integral geometry approach, decreased dramatically for model protein (lentil lectin labeled with fluorescein isothiocyanate) at transition from pH 5 to pH 9, showing only very weak thermal-dependence. Strong protein adsorption response to pH and very weak one to temperature was confirmed by TOF-SIMS and Principal Component Analysis.

Improved thermal stability of lipase in W/O microemulsion by temperature-sensitive polymers

Lipase is active at the water-oil interface and thus very useful for many applications in non-aqueous media. However, the use of lipase is often limited due to the heat inactivation which is mainly caused by the irreversible aggregation among lipase molecules. The temperature-sensitive polymers can spontaneously form complexes with lipases at higher temperature in the confined spaces of the water in oil microemulsion. With cooling, lipases are released from the complexes and refold into the native state. In this way, the thermal stability of lipase in a microemulsion is effectively improved, and so is the stability of lipase at ambient temperature. Apart from proving the effectiveness and generality of this method, the temperature-sensitive polymers/lipase microemulsion represents a simple and efficient system which could be used in practical applications, since lipase retains the interfacial activity in this system. Moreover, the influences of some factors on the improvement are discussed and the mechanism of this method is suggested after exploring the process by dynamic light scattering and fluorescence measurements.

Facile fabrication of multistimuli-responsive metallo-supramolecular core cross-linked block copolymer micelles

Metallo-supramolecular core cross-linked (CCL) micelles are fabricated from terpyridine-functionalized double hydrophilic block copolymers, poly(2-(2-methoxyethoxy)ethyl methacrylate)-b-poly(2-(diethylamino)ethyl methacrylate-co-4'-(6-methacryloxyhexyloxy)-2,2':6',2″-terpyridine) [PMEO2 MA-b-P(DEA-co-TPHMA)] via the formation of bis(terpyridine)ruthenium(II) complexes. These metallo-supramolecular CCL micelles exhibit not only high structural integrity under different pH values and temperatures in aqueous solution, but multistimuli responsiveness including pH-responsive cores, thermo-responsive shells, and reversible dissociation of bis(terpyridine)ruthenium(II) complexes upon addition of competitive metal ion chelator, which allows for precisely controlled release of the encapsulated hydrophobic guest molecules via the combination of different stimuli.

pH-dependent, thermosensitive polymeric nanocarriers for drug delivery to solid tumors

Polymeric micelles are promising carriers for anti-cancer agents due to their small size, ease of assembly, and versatility for functionalization. A current challenge in the use of polymeric micelles is the sensitive balance that must be achieved between stability during prolonged blood circulation and release of active drug at the tumor site. Stimuli-responsive materials provide a mechanism for triggered drug release in the acidic tumor and intracellular microenvironments. In this work, we synthesized a series of dual pH- and temperature-responsive block copolymers containing a poly(ε-caprolactone) (PCL) hydrophobic block with a poly(triethylene glycol) block that were copolymerized with an amino acid-functionalized monomer. The block copolymers formed micellar structures in aqueous solutions. An optimized polymer that was functionalized with 6-aminocaproic acid (ACA) possessed pH-sensitive phase transitions at mildly acidic pH and body temperature. Doxorubicin-loaded micelles formed from these polymers were stable at blood pH (~7.4) and showed increased drug release at acidic pH. In addition, these micelles displayed more potent anti-cancer activity than free doxorubicin when tested in a tumor xenograft model in mice.