Manufacture and characterization of mucoadhesive buccal films

Mucoadhesive therapeutic compositions: a patent review (2011-2014)

INTRODUCTION

With the introduction of mucoadhesion in 1980, pharmaceutical researchers have gained interest in mucoadhesive compositions. This interest has led to the development of mucoadhesive drug delivery systems aiming (I) to target a specific tissue, (II) to overcome barriers to absorption as well as (III) to control drug release of the therapeutic compositions.

AREAS COVERED

In this review, the term mucoadhesion and a variety of targetable mucosa are described through review of the literature. Mucoadhesive drug delivery systems and mucoadhesive polymers, such as thiomers, which are reported within the patent literature or in related publications are described in detail, including their therapeutic uses.

EXPERT OPINION

Mucoadhesion is associated with benefits such as controlled, sustained release, prolonged residence time at the site of action, the ability to target specific mucosae and ease of application which leads to higher rates of patient compliance. Although many research groups are investigating in this domain, not many drug delivery systems based on mucoadhesive polymers have got from bench to market. The most promising and advanced applications seen in patent literature within the last five years seems to be for oral application.

Maleimide-bearing nanogels as novel mucoadhesive materials for drug delivery

Novel class of mucoadhesive polymers has been developedviapolymerisation of 2,5-dimethylfuran-protected 3-maleimidoethyl butylacrylate in the presence of presynthesised poly(N-vinylpyrrolidone) nanogel scaffolds. The resulting maleimide-bearing nanogels were capable of forming covalent linkages with mucosal membranes.

Formulation and optimization of mucoadhesive buccal patches of losartan potassium by using response surface methodology

BACKGROUND

This study was undertaken with an aim to systematically design a model of factors that would yield an optimized sustained release dosage form of an anti-hypertensive agent, losartan potassium, using response surface methodology (RSM) by employing 3(2) full factorial design.

MATERIALS AND METHODS

Mucoadhesive buccal patches were prepared using different grades of hydroxypropyl methylcellulose (HPMC) (K4M and K100M) and polyvinylpyrrolidone-K30 by solvent casting method. The amount of the release retardant polymers - HPMC K4M (X1) and HPMC K100M (X2) was taken as an independent variable. The dependent variables were the burst release in 30 min (Y1), cumulative percentage release of drug after 8 h (Y2) and swelling index (Y3) of the patches. In vitro release and swelling studies were carried out and the data were fitted to kinetic equations.

RESULTS

The physicochemical, bioadhesive, and swelling properties of patches were found to vary significantly depending on the viscosity of the polymers and their combination. Patches showed an initial burst release preceding a more gradual sustained release phase following a nonfickian diffusion process.

DISCUSSION

The results indicate that suitable bioadhesive buccal patches with desired permeability could be prepared, facilitated with the RSM.

Fabrication and In Vitro/In Vivo Performance of Mucoadhesive Electrospun Nanofiber Mats Containing α-Mangostin

This study aimed to fabricate mucoadhesive electrospun nanofiber mats containing α-mangostin for the maintenance of oral hygiene and reduction of the bacterial growth that causes dental caries. Synthesized thiolated chitosan (CS-SH) blended with polyvinyl alcohol (PVA) was selected as the mucoadhesive polymer. α-Mangostin was incorporated into the CS-SH/PVA solution and electrospun to obtain nanofiber mats. Scanning electron microscopy, differential scanning calorimetry, X-ray diffraction, and tensile strength testing were used to characterize the mats. The swelling degree and mucoadhesion were also determined. The nanofiber mats were further evaluated regarding their α-mangostin content, in vitro α-mangostin release, antibacterial activity, cytotoxicity, in vivo performance, and stability. The results indicated that the mats were in the nanometer range. The α-mangostin was well incorporated into the mats, with an amorphous form. The mats showed suitable tensile strength, swelling, and mucoadhesive properties. The loading capacity increased when the initial amount of α-mangostin was increased. Rapid release of α-mangostin from the mats was achieved. Additionally, a fast bacterial killing rate occurred at the lowest concentration of nanofiber mats when α-mangostin was added to the mats. The mats were less cytotoxic after use for 72 h. Moreover, in vivo testing indicated that the mats could reduce the number of oral bacteria, with a good mouth feel. The mats maintained the amount of α-mangostin for 6 months. The results suggest that α-mangostin-loaded mucoadhesive electrospun nanofiber mats may be a promising material for oral care and the prevention of dental caries.

Mucoadhesive oral films: The potential for unmet needs

Oral drug delivery is the most common route of drug administration. Nevertheless, there are some important limitations that reinforce the need for developing new drug delivery systems. Mucoadhesive oral films (MOF) are promising dosage forms that adhere to the oral mucosa and deliver the drug through it, which present several advantages. These include: bypassing the hepatic first pass effect, fast onset of action, ease of transportation and handling. The use of such dosage form is beneficial for drugs that have poor oral bioavailability and also for drugs that need to be rapidly absorbed. In spite of the known benefits, the number of marketed MOF is still quite small. This review explores the products under development and corresponding clinical trials in respect to their status, therapeutic indication, companies involved and technologies. In this way, it was possible to identify the preferred therapeutic indications, new research and market trends as well as future prospects of MOF. Moreover, it is reasonable to expect an increase in the number of products on the market due to their great potential to satisfy unmet medical needs.

Formulation, characterisation and stabilisation of buccal films for paediatric drug delivery of omeprazole

This study aimed to develop films for potential delivery of omeprazole (OME) via the buccal mucosa of paediatric patients. Films were prepared using hydroxypropylmethylcellulose (HPMC), methylcellulose (MC), sodium alginate (SA), carrageenan (CA) and metolose (MET) with polyethylene glycol (PEG 400) as plasticiser, OME (model drug) and L-arg (stabiliser). Gels (1% w/w) were prepared at 40°C using water and ethanol with PEG 400 (0-1% w/w) and dried in an oven (40°C). Optimised formulations containing OME and L-arg (1:1, 1:2 and 1:3) were prepared to investigate the stabilisation of the drug. Tensile properties (Texture analysis, TA), physical form (differential scanning calorimetry, DSC; X-ray diffraction, XRD; thermogravimetric analysis, TGA) and surface topography (scanning electron microscopy, SEM) were investigated. Based on the TA results, SA and MET films were chosen for OME loading and stabilisation studies as they showed a good balance between flexibility and toughness. Plasticised MET films were uniform and smooth whilst unplasticised films demonstrated rough lumpy surfaces. SA films prepared from aqueous gels showed some lumps on the surface, whereas SA films prepared from ethanolic gels were smooth and uniform. Drug-loaded gels showed that OME was unstable and therefore required addition of L-arg. The DSC and XRD suggested molecular dispersion of drug within the polymeric matrix. Plasticised (0.5% w/w PEG 400) MET films prepared from ethanolic (20% v/v) gels and containing OME: L-arg 1:2 showed the most ideal characteristics (transparency, ease of peeling and flexibility) and was selected for further investigation.

Engineering Stent Based Delivery System for Esophageal Cancer Using Docetaxel

Esophageal cancer patients are often diagnosed as "advanced" cases. These patients are subjected to palliative stenting using self-expanding metallic stents (SEMS) to maintain oral alimentation. Unfortunately, SEMS get reoccluded due to tumor growth, in and over the stent struts. To investigate potential solutions to this problem, docetaxel (DTX) delivery films were prepared using PurSil AL 20 (PUS), which can be used as a covering material for the SEMS. Drug-polymer miscibility and interactions were studied. Bilayer films were prepared by adhering the blank film to the DTX loaded film in order to maintain the unidirectional delivery to the esophagus. In vitro release and the local DTX delivery were studied using in vitro permeation experiments. It was found that DTX and PUS were physically and chemically compatible. The bilayer films exhibited sustained release (>30 days) and minimal DTX permeation through esophageal tissues in vitro. The rate-determining step for the DTX delivery was calculated. It was found that >0.9 fraction of rate control lies with the esophageal tissues, suggesting that DTX delivery can be sustained for longer periods compared to the in vitro release observed. Thus, the bilayer films can be developed as a localized sustained delivery system in combination with the stent.

Carmellose Mucoadhesive Oral Films Containing Vermiculite/Chlorhexidine Nanocomposites as Innovative Biomaterials for Treatment of Oral Infections

Infectious stomatitis represents the most common oral cavity ailments. Current therapy is insufficiently effective because of the short residence time of topical liquid or semisolid medical formulations. An innovative application form based on bioadhesive polymers featuring prolonged residence time on the oral mucosa may be a solution to this challenge. This formulation consists of a mucoadhesive oral film with incorporated nanocomposite biomaterial that is able to release the drug directly at the target area. This study describes the unique approach of preparing mucoadhesive oral films from carmellose with incorporating a nanotechnologically modified clay mineral intercalated with chlorhexidine. The multivariate data analysis was employed to evaluate the influence of the formulation and process variables on the properties of the medical preparation. This evaluation was complemented by testing the antimicrobial and antimycotic activity of prepared films with the aim of finding the most suitable composition for clinical application. Generally, the best results were obtained with sample containing 20 mg of chlorhexidine diacetate carried by vermiculite, with carmellose in the form of nonwoven textile in its structure. In addition to its promising physicomechanical, chemical, and mucoadhesive properties, the formulation inhibited the growth of Staphylococcus and Candida; the effect was prolonged for tens of hours.

Quality by design approach for optimizing the formulation and physical properties of extemporaneously prepared orodispersible films

The quality by design (QbD) approach was applied for optimizing the formulation of extemporaneously prepared orodispersible films (ODFs) using Design-Expert® Software. The starting formulation was based on earlier experiments and contained the film forming agents hypromellose and carbomer 974P and the plasticizer glycerol (Visser et al., 2015). Trometamol and disodium EDTA were added to stabilize the solution. To optimize this formulation a quality target product profile was established in which critical quality attributes (CQAs) such as mechanical properties and disintegration time were defined and quantified. As critical process parameters (CPP) that were evaluated for their effect on the CQAs the percentage of hypromellose and the percentage of glycerol as well as the drying time were chosen. Response surface methodology (RMS) was used to evaluate the effects of the CPPs on the CQAs of the final product. The main factor affecting tensile strength and Young's modulus was the percentage of glycerol. Elongation at break was mainly influenced by the drying temperature. Disintegration time was found to be sensitive to the percentage of hypromellose. From the results a design space could be created. As long as the formulation and process variables remain within this design space, a product is obtained with desired characteristics and that meets all set quality requirements.

Polymeric formulations for drug release prepared by hot melt extrusion: application and characterization

Over the past few decades hot melt extrusion (HME) has emerged as a powerful processing technology for the production of pharmaceutical solid dosage forms in which an active pharmaceutical ingredient (API) is dispersed into polymer matrices. It has been shown that formulations using HME can provide time-controlled, sustained and targeted drug delivery, and improved bioavailability of poorly soluble drugs. In this review, the basic principles of the HME process are described together with an overview of some of the most common biodegradable and nonbiodegradable polymers used for the preparation of different formulations using this method. Further, the applications of HME in drug delivery and analytical techniques employed to characterize HME products are addressed.

Evaluation of in vitro wound adhesion characteristics of composite film and wafer based dressings using texture analysis and FTIR spectroscopy: a chemometrics factor analysis approach

Comparing adhesion of film and wafer based dressings using texture analysis and FTIR spectroscopy combined with chemometrics target factor analysis.

Inhibitory activity of the isoflavone biochanin A on intracellular bacteria of genus Chlamydia and initial development of a buccal formulation

Given the established role of Chlamydia spp. as causative agents of both acute and chronic diseases, search for new antimicrobial agents against these intracellular bacteria is required to promote human health. Isoflavones are naturally occurring phytoestrogens, antioxidants and efflux pump inhibitors, but their therapeutic use is limited by poor water-solubility and intense first-pass metabolism. Here, we report on effects of isoflavones against C. pneumoniae and C. trachomatis and describe buccal permeability and initial formulation development for biochanin A. Biochanin A was the most potent Chlamydia growth inhibitor among the studied isoflavones, with an IC₅₀ = 12 µM on C. pneumoniae inclusion counts and 6.5 µM on infectious progeny production, both determined by immunofluorescent staining of infected epithelial cell cultures. Encouraged by the permeation of biochanin A across porcine buccal mucosa without detectable metabolism, oromucosal film formulations were designed and prepared by a solvent casting method. The film formulations showed improved dissolution rate of biochanin A compared to powder or a physical mixture, presumably due to the solubilizing effect of hydrophilic additives and presence of biochanin A in amorphous state. In summary, biochanin A is a potent inhibitor of Chlamydia spp., and the in vitro dissolution results support the use of a buccal formulation to potentially improve its bioavailability in antichlamydial or other pharmaceutical applications.

Pharmaceutical and pharmacokinetic evaluation of a novel fast dissolving film formulation of flupentixol dihydrochloride

The objective of the present study was to develop fast dissolving oral film of the antipsychotic drug, flupentixol dihydrochloride, to enhance its bioavailability, optimize its therapeutic effect when used to treat depression with anxiety, and increase the convenience and compliance by the mentally ill, developmentally disable, elderly, and pediatric patients. Six formulae were prepared with different concentrations of water-soluble polymers vis. hydroxypropyl methylcellulose (HPMC E5) and carboxymethyl cellulose (CMC) by solvent casting technique. The prepared films were subjected to characterization for folding endurance, weight variations, thickness, disintegration time, drug release pattern, and drug content. Physical compatibility between the drug and excipients was guaranteed in the selected formulation (2% HPMC) by means of differential scanning calorimetry analysis and Fourier-transform infrared spectroscopy. This formulation revealed high stability after testing according to the International Conference on Harmonisation guidelines. In vivo studies based on single phase parallel design were carried out for the optimized formulation in healthy human volunteers. The concentration of flupentixol dihydrochloride in plasma samples was analyzed by a developed validated LC-MS/MS assay method and the pharmacokinetic parameters of the established formulation were compared with the commercially available oral tablets. Faster rate of absorption of flupentixol could be obtained from the oral film formulation and the relative bioavailability was found to be 151.06% compared to the marketed product.

Screening of mucoadhesive vaginal gel formulations

Rational design of vaginal drug delivery formulations requires special attention to vehicle properties that optimize vaginal coating and retention. The aim of the present work was to perform a screening of mucoadhesive vaginal gels formulated with carbomer or carrageenan in binary combination with a second polymer (carbomer, guar or xanthan gum). The gels were characterised using in vitroadhesion, spreadability and leakage potential studies, as well as rheological measurements (stress and frequency sweep tests) and the effect of dilution with simulated vaginal fluid (SVF) on spreadability. Results were analysed using analysis of variance and multiple factor analysis. The combination of polymers enhanced adhesion of both primary gelling agents, carbomer and carrageenan. From the rheological point of view all formulations presented a similar behaviour, prevalently elastic and characterised by loss tangent values well below 1. No correlation between rheological and adhesion behaviour was found. Carbomer and carrageenan gels containing the highest percentage of xanthan gum displayed good in vitro mucoadhesion and spreadability, minimal leakage potential and high resistance to dilution. The positive results obtained with carrageenan-xanthan gum-based gels can encourage the use of natural biocompatible adjuvants in the composition of vaginal products, a formulation field that is currently under the synthetic domain.

Mucoadhesive electrospun chitosan-based nanofibre mats for dental caries prevention

The mucoadhesive electrospun nanofibre mats were developed using chitosan (CS) and thiolated chitosan (CS-SH) as mucoadhesive polymers. Garcinia mangostana (GM) extract was incorporated into nanofibre mats. The antibacterial activity in the single and combined agents was evaluated against dental caries pathogens. The morphology of mats was observed using SEM. The mats were evaluated for GM extract amount, mucoadhesion, in vitro release, antibacterial activity and cytotoxicity. The mucoadhesion and antibacterial activity were determined in healthy human volunteers. The prepared mats were in nanoscale with good physical and mucoadhesive properties. The CS-SH caused the higher mucoadhesion. All mats rapidly released active substances, which had the synergistic antibacterial activity. In addition, the reduction of bacteria and good mucoadhesion in the oral cavity occurred without cytotoxicity. The results suggest that mats have the potential to be mucoadhesive dosage forms to maintain oral hygiene by reducing the bacterial growth that causes the dental caries.

Efficacy of orally disintegrating film of ondansetron versus intravenous ondansetron in prophylaxis of postoperative nausea and vomiting in patients undergoing elective gynaecological laparoscopic procedures: A prospective randomised, double-blind placebo-controlled study

Background and Aims:

Ondansetron is one of the most widely used drugs for postoperative nausea and vomiting (PONV) prophylaxis. Orally disintegrating film (ODF) formulations are relatively recent innovations. We evaluated the efficacy of ODF of ondansetron for the prophylaxis of PONV.

Methods:

One hundred and eighty American Society of Anaesthesiologists-I or II women, in the age group 18-65 years, scheduled for elective gynaecological laparoscopic procedures were studied in a prospective randomised, double-blind, placebo-controlled trial. The patients were randomised into four groups: Placebo, intravenous (IV) ondansetron 4 mg, ODF of ondansetron 4 mg (ODF4) and 8 mg (ODF8) groups. PONV was assessed in two epochs of 0-6 and 7-24 h. Primary outcome measure was the incidence of PONV and secondary outcome measures were severity of nausea, need for rescue anti-emetic, analgesic consumption, time to oral intake, overall patient satisfaction and side effects such as headache and dizziness. PONV was compared using analysis of variance or Mann–Whitney U-test as applicable.

Results:

Data of 173 patients were analysed. The incidence of postoperative nausea was significantly lower (P = 0.04) only during the 0-6 h in the ODF8 group when compared with the placebo group. During the 0-6 h interval postoperatively, the ODF8 group had a significantly lower incidence of vomiting when compared with the placebo (P = 0.002) and the IV group (P = 0.044). During the 0-24 h interval postoperatively, ODF4 (P = 0.01) and ODF8 (P = 0.002) groups had a significantly lower incidence of vomiting compared to the placebo group.

Conclusions:

Orally disintegrating film of ondansetron is an efficacious, novel, convenient and may be a cost-effective option for the prophylaxis of PONV.

Chitosan-based mucoadhesive films containing 5-aminolevulinic acid for buccal cancer's treatment

Photodynamic therapy (PDT) is a relatively new method to treat various kinds of tumors, including those of the oral cavity. The topical 5-ALA-PDT treatment for tumors of the oral mucosa is preferred, since when administered systemically, there is a general photosensitization drawback in the patient. However, 5-ALA is a hydrophilic molecule and its penetration and retention is limited by topical route, including oral mucosa. We propose a topical delivery system of chitosan-based mucoadhesive film, aiming to promote greater retention of 5-ALA in tissue. The chitosan (CHT) films (4% w/w) were prepared using the solvent evaporation/casting technique. They were tested without 5-ALA resulting in permeability to water vapor (W.V.P=2.15-8.54 g mm/(h cm(2)Pa) swelling ∼300.0% (±10.5) at 4 h or 24 h and in vitro residence time >24 h for all tests. CHT films containing 10.0% (w/w) 5-ALA have resulted in average weight of 0.22 g and thickness of 0.608 mm as suitable characteristics for oral application. In the presence of CHT films both in vitro permeation and retention of 5-ALA (1.0% or 10.0%) were increased. However, 10.0% 5-ALA presented highest values of permeation and retention (∼4 and 17 times respectively, compared to propylene glycol vehicle). On the other hand, in vitro mucoadhesion of CHT films was decreased (18.2-fold and 3.1-fold) by 5-ALA addition (1.0% or 10.0% respectively). However, CHT film containing 10.0% of 5-ALA can be a potential delivery system for topical use in the treatment of tumors of the oral cavity using PDT because it favored the retention of 5-ALA in this tissue and has shown convenient mucoadhesion.

Evaluation of the influence of formulation and process variables on mechanical properties of oral mucoadhesive films using multivariate data analysis

Oral mucosa is an attractive region for the local and systemic application of many drugs. Oral mucoadhesive films are preferred for their prolonged time of residence, the improved bioavailability of the drug they contain, their painless application, their protection against lesions, and their nonirritating properties. This work was focused on preparation of nonmedicated carmellose-based films using both solvent casting and impregnation methods, respectively. Moreover, a modern approach to evaluation of mucoadhesive films applying analysis of texture and subsequent multivariate data analysis was used. In this experiment, puncture strength strongly correlated with tensile strength and could be used to obtain necessary information about the mechanical film characteristics in films prepared using both methods. Puncture work and tensile work were not correlated in films prepared using the solvent casting method, as increasing the amount of glycerol led to an increase in the puncture work in thinner films. All measured texture parameters in films prepared by impregnation were significantly smaller compared to films prepared by solvent casting. Moreover, a relationship between the amount of glycerol and film thickness was observed, and a greater recalculated tensile/puncture strength was needed for an increased thickness in films prepared by impregnation.

Buccal and sublingual vaccine delivery

Because of their large surface area and immunological competence, mucosal tissues are attractive administration and target sites for vaccination. An important characteristic of mucosal vaccination is its ability to elicit local immune responses, which act against infection at the site of pathogen entry. However, mucosal surfaces are endowed with potent and sophisticated tolerance mechanisms to prevent the immune system from overreacting to the many environmental antigens. Hence, mucosal vaccination may suppress the immune system instead of induce a protective immune response. Therefore, mucosal adjuvants and/or special antigen delivery systems as well as appropriate dosage forms are required in order to develop potent mucosal vaccines.

Whereas oral, nasal and pulmonary vaccine delivery strategies have been described extensively, the sublingual and buccal routes have received considerably less attention. In this review, the characteristics of and approaches for sublingual and buccal vaccine delivery are described and compared with other mucosal vaccine delivery sites. We discuss recent progress and highlight promising developments in the search for vaccine formulations, including adjuvants and suitable dosage forms, which are likely critical for designing a successful sublingual or buccal vaccine. Finally, we outline the challenges, hurdles to overcome and formulation issues relevant for sublingual or buccal vaccine delivery.

Buccal films of prednisolone with enhanced bioavailability

The conventional formulation of prednisolone is considered to be low in efficacy, primarily on account of their failure in providing and maintaining effective therapeutic drug levels. This study aims to focus on development of a mucoadhesive buccal delivery system with a twofold objective of offering a rapid as well as a prolonged delivery of prednisolone coupled with enhanced therapeutic efficacy. Buccoadhesive films of prednisolone were prepared by solvent-casting method using hydroxyl propyl methyl cellulose (K100), Carbopol 940 and/or Eudragit NE 40 D. Placebo films possessing the most desirable physicomechanical properties were selected for drug loading. The effect of polymer and its content on film properties, i.e. mucoadhesive strength, swelling and hydration, in vitro drug release was studied. Based on these studies, film F7D was selected for ex vivo permeation across porcine cheek mucosa. The steady state flux of prednisolone across the buccal mucosa was found to be 105.33 ± 32.07 µg/cm(2)/h. A comparative pharmacokinetic study of prepared film (F7D) and oral suspension of prednisolone was conducted. In vivo data of buccal film show greater bioavailability (AUC0-α: 24.26 ± 4.06 µg.h/ml versus 10.65 ± 2.15 µg.h/ml) and higher Cmax (2.70 ± 0.38 µg/ml versus 2.29 ± 0.32 µg/ml) value when compared to oral suspension. The data observed from this study highlight the feasibility of the buccal route as a viable option for delivery of prednisolone.

Oral transmucosal drug delivery for pediatric use

The formulation of medicines for children remains a challenge. An ideal pediatric formulation must allow accurate dose administration and be in a dosage form that can be handled by the target age group. It is also important to consider the choices and the amount of excipients used in the formulation for this vulnerable age group. Although oral formulations are generally acceptable to most pediatric patients, they are not suitable for drugs with poor oral bioavailability or when a rapid clinical effect is required. In recent years, oral transmucosal delivery has emerged as an attractive route of administration for pediatric patients. With this route of administration, a drug is absorbed through the oral mucosa, therefore bypassing hepatic first pass metabolism and thus avoiding drug degradation or metabolism in the gastrointestinal tract. The high blood flow and relatively high permeability of the oral mucosa allow a quick onset of action to be achieved. It is a simple and non-invasive route of drug administration. However, there are several barriers that need to be overcome in the development of oral transmucosal products. This article aims to provide a comprehensive review of the current development of oral transmucosal delivery specifically for the pediatric population in order to achieve systemic drug delivery. The anatomical and physiological properties of the oral mucosa of infants and young children are carefully examined. The different dosage forms and formulation strategies that are suitable for young patients are discussed.

Novel oleic acid derivatives enhance buccal permeation of didanosine

The aim of this study was to explore the potential of novel oleic acid (OA) derivatives as buccal permeation enhancers for the delivery of didanosine (ddI). The OA derivatives, i.e. ester derivative (OA1E), the dicarboxylic acid derivative (OA1A) and the bicephalous dianionic surfactant (OA1ANa) were synthesized and their effects were compared to the parent OA. OA, OA1E, OA1A and OA1ANa at 1% w/w all showed potential for enhancing the buccal permeability of ddI with enhancement ratio (ER) of 1.29, 1.33, 1.01 and 1.72, respectively. OA1ANa at 1% w/w demonstrated the highest flux (80.30 ± 10.37 µg cm(-2 )h), permeability coefficient (4.01 ± 0.57 × 10(-3) cm h(-1)) and ER (1.72). The highest flux for ddI (144.00 ± 53.54 µg cm(-2 )h) was reported with OA1ANa 2% w/w, which displayed an ER of 3.09 more than that with ddI alone. At equivalent concentrations, OA1ANa (ER = 3.09) had a significantly higher permeation-enhancing effect than its parent OA (ER = 1.54). Histomorphological studies confirmed that OA1ANa at all concentrations (0.5, 2.0 and 6.0% w/w) had no adverse effects on the mucosae. Morphological changes such as vacuoles formation and increased intercellular spaces were attributed to the buccal permeation-enhancing effect of OA1ANa. This study demonstrated the potential of novel OA derivatives as buccal permeation enhancers. OA1ANa at 2% w/w was also identified as the optimal novel OA derivative to widen the pool of fatty acid derivatives as chemical permeation enhancers for buccal drug delivery.

Design and evaluation of bilayered buccal film preparations for local administration of lidocaine hydrochloride

Bilayered oromucosal film preparations (buccal films) offer a promising way to enable drug administration via the oral cavity. Adding a non-soluble or slowly eroding/dissolving backing layer to a mucoadhesive drug-loaded layer enables unidirectional drug delivery. The aim of this study was to investigate different approaches to the manufacture of bilayered films and to examine their properties by applying different characterization methods including an optimized experimental setup for the study of drug release from bilayered films. A solvent suitability study was performed screening over 15 polymers with respect to their feasibility for viscous film formation for film preparation by solvent casting method. Two methods (double-casting and pasting) were found as suitable methods for bilayered film manufacturing. Results from drug release experiments indicated that slowly eroding hypromellose backing layer films revealed the best shielding of the drug-loaded layer to enable unidirectional drug release. In summary, manufacturing of bilayered films using the described methods was feasible. Furthermore, the use of an optimized experimental setup for drug dissolution studies enabled monitoring of drug release without delays in sampling.