Determination of carcinoembryonic antigen in human sera by integrated bead-bed immunoassay in a microchip for cancer diagnosis

Integration of chemical and biochemical analysis systems into a glass microchip

This review focuses on the integration of chemical and biochemical analysis systems into glass microchips for general use. By combining multiphase laminar flow driven by pressure and micro unit operations, such as mixing, reaction, extraction and separation, continuous-flow chemical processing systems can be realized in the microchip format, while the application of electrophoresis-based chip technology is limited. The performances of several analysis systems were greatly improved by microchip integration because of some characteristics of microspace, i.e., a large specific interface area, a short molecular diffusion time, a small heat capacity and so on. By applying these concepts, several different analysis systems, i.e., wet analysis of cobalt ion, multi-ion sensor, immunoassay, and cellular analysis, were successfully integrated on a microchip. These microchip technologies are promising for meeting the future demands of high-throughput chemical processing.

Competitive quenching fluorescence immunoassay for chlorophenols based on laser-induced fluorescence detection in microdroplets

An improved biomonitoring system for the analysis of 2,4,6-trichlorophenol (TCP) in urine samples has been developed. The principle of the biosensor device is the detection of laser-induced fluorescence (LIF) in single microdroplets by a homogeneous quenching fluorescence immunoassay (QFIA). The competitive immunoassay occurs in microdroplets (d = 58,4 microm) produced by a piezoelectric generator system with 10-microm-diameter orifice. A continuous Ar ion laser (488 nm) excites the fluorescent tracer; its fluorescence is detected by a spectrometer attached to a 512 x 512 cooled, charge-coupled device camera. Fluorescence is quenched by specific binding of TCP polyclonal antibodies to the fluorescent tracer (hapten A-fluorescein); the quenching effect is diminished by the presence of the analyte. Thus, an increase in the signal is produced in a positive dose-dependent manner when TCP is present in the sample. In 10 mM PBS buffer, the IC50 of the LIF-microdroplet QFIA is 0.45 microg L(-1) reaching a LOD of 0.04 microg L(-1). The QFIA with the same reagents performed in microtiter plate format achieved a LOD of 0.36 microg L(-1) in buffer solution. Performance in human urine was similar to that observed in the buffer. A LOD of 1.6 ,g L(-1), with a dynamic range between 4 and 149.5 microg L(-1) in urine, was obtained without any sample treatment other than dilution with the assay buffer. The detectability achieved is sufficient for occupational exposure risk assessment.

Microchip-based amperometric immunoassays using redox tracers

A new chip-based electrochemical immunoassay protocol, based on the use of a ferrocene redox label, is described. Two reaction formats, based on direct (noncompetitive) and competitive modes of operation, were employed for illustrating the use of redox tracers in chip-based electrochemical immunoassays. The direct assay consisted of mixing the ferrocene-tagged antibody and the antigen analyte, a rapid electrophoretic separation of labeled free antibody and the labeled antigen/antibody complex, and a downstream anodic detection of the ferrocene tracer at gold-plated carbon screen-printed electrode detector. The competitive assay integrates precolumn reactions of the labeled antigen and the target antigen with the antibody with electrophoretic separation of the free and bound labeled antigens, along with amperometric detection of the redox tag. An internal standard has been used to normalize the peak area for the construction of calibration plots. Fundamental operating variables are examined and optimized. The use of a redox tracer offers the advantages of simplified protocol, wider linear range, higher stability, and higher separation efficiency compared to an analogous use of enzyme tags. The direct mouse-immunoglobulin G (IgG) assay and the competitive 3,3',5-triiodo-L-thyronine (T(3)) one were accomplished within less than 150 and 130 s (with field strengths of 256 and 192 V/cm), and offer minimum detectable concentrations of 2.5 x 10(-12) and 1 x1 0(-6) g/mL, respectively. Such use of redox labels for chip-based amperometric immunoassay protocols offers considerable promise for decentralized clinical or environmental testing.

Glass microchip with three-dimensional microchannel network for 2 x 2 parallel synthesis

An integrated multireactor system for 2 x 2 parallel organic synthesis has been developed on a single glass microchip. Three-dimensional channel circuits in the chip were fabricated by laminating three glass plate layers. The fabrication method is a straightforward extension of the conventional one, and topological equivalence for any three-dimensional circuits can be constructed easily with it. 2 x 2 phase-transfer amide formation reactions, which constitute a simple model for combinatorial synthesis, were successfully carried out on the microchip, and the integrity of the three-dimensional circuits was confirmed. Combinatorial chemistry with multi-microreactors, in conjunction with a high-throughput screening method based on micro-TAS technologies, is expected to provide an efficient tool for drug discovery.

Three-dimensional microfluidic confinement for efficient sample delivery to biosensor surfaces. application to immunoassays on planar optical waveguides

A microchip-based flow confinement method for rapid delivery of small sample volumes to sensor surfaces is described. For flow confinement, a sample flow is joined with a perpendicular makeup flow of water or sample medium. Under laminar flow conditions, the makeup flow confines the sample into a thin layer above the sensing area and increases its velocity. This can benefit mass transport limited processes such as DNA hybridization or heterogeneous immunoassays. For proof of concept, this method was applied to a high-affinity immunoassay with excess capture antibody. Rabbit IgG was immobilized onto a silicon nitride waveguide. Cy5-labeled anti-rabbit IgG was hydrodynamically pumped over the immobilized zone through an attached 3D-PDMS flow cell with 20-microm-deep microchannels. The degree of confinement was adjusted through the volume flow rate of the confining flow. Evanescent field-based fluorescence detection enabled monitoring of the binding event. Assays were allowed to reach equilibrium to enable sensorgram normalization for inter-run comparison. The corresponding assay completion times could be reduced from 55 min for static drop conditions to 13 min for 25:1 flow confinement (ratio of confining to sample flow). For typical analytical applications, where equilibrium formation is not required, the faster response should translate to very short analysis times. Concurrently with the faster binding, sample consumption was reduced by 96% compared to conventional whole-channel sample delivery. Diffusional loss of analyte into the confining layer was identified as the main limitation of flow confinement, particularly for long sensing pads.

Enzymatic microreactor-on-a-chip: protein mapping using trypsin immobilized on porous polymer monoliths molded in channels of microfluidic devices

Enzymatic microreactors have been prepared in capillaries and on microfluidic chips by immobilizing trypsin on porous polymer monoliths consisting of 2-vinyl-4,4-dimethylazlactone, ethylene dimethacrylate, and acrylamide or 2-hydroxyethyl methacrylate. The azlactone functionalities react readily with amine and thiol groups of the enzyme to form stable covalent bonds. The optimized porous properties of the monoliths lead to very low back pressures enabling the use of simple mechanical pumping to carry out both the immobilization of the enzyme from its solution and the subsequent analyses of substrate solutions. The Michealis-Menten kinetic characteristics of the reactors were probed using a low molecular weight substrate: N-alpha-benzoyl-L-arginine ethyl ester. The effects of immobilization variables such as the concentration of trypsin in solution and percentage of azlactone functionalities in the monolith, as well as the effect of reaction time on the enzymatic activity, and of process variables such as substrate flow velocity and residence time in the reactor, were studied in detail. The proteolytic activity of the enzymatic microreactor on chip was demonstrated at different flow rates with the cleavage of fluorescently labeled casein used as a substrate. The excellent performance of the monolithic microreactor was also demonstrated with the digestion of myoglobin at the fast flow rate of 0.5 microL/min, which affords a residence time of only 11.7 s. The digest was then characterized using MALDI-TOF MS, and 102 out of 153 possible peptide fragments were identified giving a sequence coverage of 67%.

Fabrication of microchambers defined by photopolymerized hydrogels and weirs within microfluidic systems: application to DNA hybridization

This paper describes fabrication of serial microchamber arrays within the channels of a microfluidic device. The chambers are defined using a combination of weirs and UV-cross-linked hydrogel plugs (poly(ethylene glycol) diacrylates). This approach permits the microchambers to be addressed by pump-driven pressure in one dimension and by electrophoresis in the other. The function of the device is demonstrated by detecting DNA targets. Single-strand DNA (ssDNA) probes labeled with biotin were immobilized onto microbeads coated with streptavidin. The DNA-functionalized microbeads were packed into each of three microchambers by injection through inlet wells. Three oligonucleotides were designed as probes and four as targets. Hybridization reactions were performed by moving the targets across the array of probe-containing microchambers by electrophoresis. The hybridization of fluorescein-labeled ssDNA targets to complementary probes was observed by fluorescence microscopy. These studies resulted in four key observations: (1) there was no detectable binding of targets to noncomplementary probes; (2) hybridization was 90% complete within 1 min; (3) once captured, the targets could be independently released and recovered from the microbeads by treatment with 0.1 N NaOH; (4) multiple analyses could be performed using a single bead set, but there was degradation in performance after each capture/release cycle.

Microfluidic enzyme immunoassay using silicon microchip with immobilized antibodies and chemiluminescence detection

Silicon microchips with immobilized antibodies were used to develop microfluidic enzyme immunoassays using chemiluminescence detection and horseradish peroxidase (HRP) as the enzyme label. Polyclonal anti-atrazine antibodies were coupled to the silicon microchip surface with an overall dimension of 13.1 x 3.2 mm, comprising 42 porous flow channels of 235-microm depth and 25-microm width. Different immobilization protocols based on covalent or noncovalent modification of the silica surface with 3-aminopropyltriethoxysilane (APTES) or 3-glycidoxypropyltrimethoxysilane (GOPS), linear polyethylenimine (LPEI, MW 750,000), or branched polyethylenimine (BPEI, MW 25,000), followed by adsorption or covalent attachment of the antibody, were evaluated to reach the best reusability, stability, and sensitivity of the microfluidic enzyme immunoassay (microFEIA). Adsorption of antibodies on a LPEI-modified silica surface and covalent attachment to physically adsorbed BPEI lead to unstable antibody coatings. Covalent coupling of antibodies via glutaraldehyde (GA) to three different functionalized silica surfaces (APTES-GA, LPEI-GA, and GOPS-BPEI-GA) resulted in antibody coatings that could be completely regenerated using 0.4 M glycine/HCl, pH 2.2. The buffer composition was shown to have a dramatic effect on the assay stability, where the commonly used phosphate buffer saline was proved to be the least suitable choice. The best long-term stability was obtained for the LPEI-GA surface with no loss of antibody activity during one month. The detection limits in the microFEIA for the three different immuno surfaces were 45, 3.8, and 0.80 ng/L (209, 17.7, and 3.7 pM) for APTES-GA, LPEI-GA, and GOPS-BPEI-GA, respectively.

Single-cell analysis by a scanning thermal lens microscope with a microchip: direct monitoring of cytochrome c distribution during apoptosis process

We developed a microsystem for cell experiments consisting of a scanning thermal lens microscope detection system and a cell culture microchip. The microchip system was good for liquid control in microspace, and this results in secure cell stimulation and coincident in vivo observation of the cell responses. The system could detect nonfluorescent biological substances with extremely high sensitivity without any labeling materials and had a high spatial resolution of approximately 1 microm. This system was applied to monitoring of cytochrome c distribution in a neuroblastoma-glioma hybrid cell cultured in the microflask (1 mm x 10 mm x 0.1 mm; 1 microL) fabricated in a glass microchip. Cytochrome c release from mitochondria to cytosol during the apoptosis process was successfully monitored with this system. The cytochrome c detected with this system was estimated to be approximately 10 zmol. We concluded that the system was suitable for measuring the distribution of chemical substances in a single cell because the microchip is good for liquid handling in microspace and the thermal lens microscope has high sensitivity and spatial resolution.

Continuous-flow chemical processing on a microchip by combining microunit operations and a multiphase flow network

A new design and construction methodology for integration of complicated chemical processing on a microchip was proposed. This methodology, continuous-flow chemical processing (CFCP), is based on a combination of microunit operations (MUOs) and a multiphase flow network. Chemical operations in microchannels, such as mixing, reaction, and extraction, were classified into several MUOs. The complete procedure for Co(II) wet analysis, including a chelating reaction, solvent extraction, and purification was decomposed into MUOs and reconstructed as CFCP on a microchip. Chemical reaction and molecular transport were realized in and between continuous liquid flows in a multiphase flow network, such as aqueous/aqueous, aqueous/organic, and aqueous/organic/aqueous flows. When the determination of Co(II) in an admixture of Cu(II) was carried out using this methodology, the determination limit (2sigma) was obtained as 18 nM, and the absolute amount of Co chelates detected was 0.13 zmol, that is, 78 chelates. The sample analysis time was faster than that of a conventional processing system. Moreover, troublesome operations such as phase separation and acid and alkali washing, all necessary for the conventional system, were simplified. The CFCP methodology proposed here can be applied to various on-chip applications.

Microfluidic chips for clinical and forensic analysis

This review gives an overview of developments in the field of microchip analysis for clinical diagnostic and forensic applications. The approach chosen to review the literature is different from that in most microchip reviews to date, in that the information is presented in terms of analytes tested rather than microchip method. Analyte categories for which examples are presented include (i) drugs (quality control, seizures) and explosives residues, (ii) drugs and endogenous small molecules and ions in biofluids, (iii) proteins and peptides, and (iv) analysis of nucleic acids and oligonucleotides. Few cases of microchip analysis of physiological samples or other "real-world" matrices were found. However, many of the examples presented have potential application for these samples, especially with ongoing parallel developments involving integration of sample pretreatment onto chips and the use of fluid propulsion mechanisms other than electrokinetic pumping.

Microchip-based immunoassay system with branching multichannels for simultaneous determination of interferon-gamma

A bead-bed immunoassay system suitable for simultaneous assay of multiple samples was constructed on a microchip. The chip had branching multichannels and four reaction and detection regions; the constructed system could process four samples at a time with only one pump unit. Interferon gamma was assayed by a 3-step sandwich immunoassay with the system coupled to a thermal lens microscope as a detector. The biases of the signal intensities obtained from each channel were within 10%, and coefficients of variation were almost the same level as the single straight channel assay. The assay time for four samples was 50 min instead of 35 min for one sample in the single-channel assay; hence higher throughput was realized with the branching structure chip.

Polymer microfluidic chips for electrochemical and biochemical analyses

Our recent developments concerning the fabrication of polymer microchips and their applications for biochemical analyses are reviewed. We first describe two methods of fabrication of polymer microfluidic chips, namely UV-laser photoablation and plasma etching that are well suited for the prototyping and mass fabrication of microchannel networks with integrated microelectrodes. These microanalytical systems can be coupled with various detection means including mass spectrometry, and their applications in capillary electrophoresis are presented here. We also present how UV laser photoablation can be used for the patterning of biomolecules on polymer surfaces for generating two-dimensional arrays of microspots to carry out affinity assays. Finally, the use of the microchips for the development of fast affinity and immunological assays with electrochemical detection is presented, demonstrating the potential of these polymer microchips for medical diagnostics and drug discovery.

Application of surface biopassivated disposable poly(dimethylsiloxane)/glass chips to a heterogeneous competitive human serum immunoglobulin G immunoassay with incorporated internal standard

A microfluidic platform for a heterogeneous competitive immunoassay of human immunoglobulin G (IgG) employing Cy5-human IgG as tracer and Cy3-mouse IgG as internal standard was developed. The device consisted of microchannels made of poly(dimethylsiloxane) and glass which were patterned with antibodies against human IgG and mouse IgG. Electrokinetic sample transport was employed in order to exploit the small difference between the net mobilities of analyte and tracer, thereby achieving favorable conditions for the performance of the competitive immunoreaction. The overall quality of the disposable chip and performance of the immunoassay were controlled by monitoring the fluorescence of bound tracer and bound internal standard. Analyses with an insufficient internal standard response were discarded, and immunoassay data evaluation was based on the ratio of tracer and internal standard fluorescence. Using synthetic samples in the range from 0 to 80 microg/mL IgG and alkaline running conditions, a concentration-dependent response with reproducible Cy5/Cy3 signal ratios (average relative standard deviation of 6.8%) was obtained. Chips stored with solution in the channels at 4 degrees C over a two-month period were found to perform like freshly prepared chips, whereas chips stored dry at -20 degrees C and rehydrated prior to use could not be employed. The analysis of patient sera showed that the immunoassay platform behaved differently in the presence of serum-based samples. Using the same conditions as for the synthetic samples, no concentration dependence was noted. With a large excess of tracer, however, an IgG concentration dependence was observed, permitting distinction of samples of patients with normal IgG serum levels (8-16 mg/mL) from those with elevated IgG concentrations (>16 mg/mL).

Biomolecular recognition on well-characterized beads packed in microfluidic channels

We describe a new approach for the analysis of biomolecular recognition in microfluidic channels. The method involves real-time detection of soluble molecules binding to receptor-bearing microspheres, sequestered in affinity column format inside a microfluidic channel. Identification and quantitation of analytes occurs via direct fluorescence measurements or fluorescence resonance energy transfer (FRET). We establish a model system that detects the FLAG epitope. The assay can potentially detect subfemtomole quantities of antibody with a high signal-to-noise ratio and a large dynamic range spanning nearly 4 orders of magnitude in analyte concentration in microliter-to-submicroliter volumes of analyte fluid. Kinetic and equilibrium constants for the reaction of this receptor-ligand pair are obtained through modeling of kinetic responses of the affinity microcolumn and are consistent with those obtained by flow cytometry. Because of the correlation between kinetic and equilibrium data obtained for the microcolumns, quantitative analysis can be done prior to the steady-state end point of the recognition reaction. This method has the promise of combining the utility of affinity chromatography with the advantage of direct, quantitative, and real-time analysis and the cost-effectiveness of microanalytical devices. The approach has the potential to be generalized to a host of bioaffinity assay methods including analysis of protein complexes and molecular assembly and microsystem-based multianalyte determinations.

An integrated fritless column for on-chip capillary electrochromatography with conventional stationary phases

A new polymer device for use with conventional particulate stationary phases for on-chip, fritless, capillary electrochromatography (CEC) has been realized. The structure includes an injector and a tapered column in which the particles of the stationary phase are retained and stabilized. The chips were easily fabricated in poly(dimethylsiloxane) using deep-reactive-ion-etched silicon masters, and tested using a capillary electrophoretic separation of FITC-labeled amino acids. To perform CEC, the separation channel was packed using a vacuum with 3-microm, octadecylsilanized silica microspheres. The packing was stabilized in the column by a thermal treatment, and its stability and quality were evaluated using in-column indirect fluorescence detection. The effects of voltage on electro-osmotic flow and on efficiency were investigated, and the separation of two neutral compounds was achieved in less than 15 s.

On-chip integration of sequential ion-sensing system based on intermittent reagent pumping and formation of two-layer flow

A sequential ion-sensing system using a single microchip was successfully realized. The system developed here involves intermittent pumping of plural organic phases into a microchannel, followed by contact with a single aqueous phase to form a stable organic-aqueous two-layer flow inside the microchannel. Because the plural organic phases created by intermittent flow contain the same lipophilic pH indicator dye but different ion-selective neutral ionophores, different ions can be sequentially and selectively extracted into the different organic phases, where they can be determined by thermal lens microscopy (TLM). We used KD-A3 as the lipophilic pH indicator dye and valinomycin and DD16C5 as neutral ionophores to demonstrate sequential ion sensing of potassium and sodium ions by measuring the deprotonated dye caused by the ion extraction. The integrated microfluidic system proposed here allows multi-ion sensing, which is not easily demonstrated by conventional ion sensor technology using a solvent polymeric membrane. The minimum volume of single organic phase needed to obtain an equilibrium response without dilution by cross dispersion of two organic phases was ca. 500 nL in our system, indicating that the required amounts of expensive reagents in one measurement could be reduced to 1.7 ng and 2.8 ng for the dye and ionophore molecules, respectively.

Electrochemical enzyme immunoassays on microchip platforms

A microfluidic device for conducting electrochemical enzyme immunoassays is described. The new "lab-on-a-chip" protocol integrates precolumn reactions of alkaline phosphatase-labeled antibody (anti-mouse IgG) with the antigen (mouse IgG), followed by electrophoretic separation of the free antibody and antibody-antigen complex. The separation is followed by a postcolumn reaction of the enzyme tracer with the 4-aminophenyl phosphate substrate and a downstream amperometric detection of the liberated 4-aminophenol product Factors influencing the reaction, separation, and detection processes were optimized, and the analytical performance was characterized. An applied field strength of 256 V/cm results in free antibody and antibody-antigen complex migration times of 125 and 340 s, respectively. A remarkably low detection limit of 2.5 x 10(-16) g/mL (1.7 x 10(-18) M) is obtained for the mouse IgG model analyte. Such combination of a complete integrated immunoassay, an attractive analytical performance, and the distinct miniaturization/portability advantages of electrochemical microsystems offers considerable promise for designing self-contained and disposable chips for decentralized clinical diagnostics or on-site environmental testing.