Progress in dimethacrylate-based dental composite technology and curing efficiency

Pre-heating of high-viscosity bulk-fill resin composites: effects on shrinkage force and monomer conversion

OBJECTIVES

To investigate the influence of pre-heating of high-viscosity bulk-fill composite materials on their degree of conversion and shrinkage force formation.

METHODS

Four bulk-fill composite materials (Tetric EvoCeram Bulk Fill-TECBF, x-tra fil-XF, QuixFil-QF, SonicFill-SF) and one conventional nano-hybrid resin composite (Tetric EvoCeram-TEC) were used. The test materials were either kept at room temperature or pre-heated to 68°C by means of a commercial heating device, before being photoactivated with a LED curing unit for 20s at 1170mW/cm(2). Shrinkage forces (n=5) of 1.5-mm-thick specimens were recorded in real-time for 15min inside a temperature-controlled chamber at 25°C (simulating intraoral temperature after rubber dam application) with a custom-made stress analyzer. Degree of conversion (n=5) was determined at the bottom of equally thick (1.5mm) specimens using Fourier transform infrared spectroscopy. Data were analyzed with Student's t-test, ANOVA and Tukey's HSD post-hoc test (α=0.05).

RESULTS

Composite pre-heating significantly increased the degree of conversion of TECBF, but had no effect on monomer conversion of the other materials investigated. For each of the test materials, pre-heated composite generated significantly lower shrinkage forces than room-temperature composite. At both temperature levels, TECBF created the significantly highest shrinkage forces, and QF caused significantly higher shrinkage forces than both XF and TEC.

CONCLUSIONS

Both the composite material and the pre-cure temperature affect shrinkage force formation. Pre-heating of bulk-fill and conventional restorative composites prior to photoactivation decreases polymerization-induced shrinkage forces without compromising the degree of conversion.

CLINICAL SIGNIFICANCE

Composite pre-heating significantly reduces shrinkage force formation of high-viscosity bulk-fill and conventional resin composites, while maintaining or increasing the degree of monomer conversion, dependent upon the specific composite material used.

Light-Curing Units

For improved interstudy reproducibility, reduced risk of premature failures, and ultimately better patient care, researchers and dentists need to know how to accurately characterize the electromagnetic radiation (light) they are delivering to the resins they are using. The output from a light-curing unit (LCU) is commonly characterized by its irradiance. If this value is measured at the light tip, it describes the radiant exitance from the surface of the light tip, and not the irradiance received by the specimen. The value quoted also reflects only an averaged value over the total measurement area and does not represent the irradiance that the resin specimen is receiving locally or at a different moment in time. Recent evidence has reported that the spectral emission and radiant exitance beam profiles from LCUs can be highly inhomogeneous. This can cause nonuniform temperature changes and uneven photopolymerization within the resin restoration. The spectral radiant power can be very different between different brands of LCUs, and the use of irradiance values derived from dental radiometers to describe the output from an LCU for research purposes is discouraged. Manufacturers should provide more information about the light output from the LCU and the absorption spectrum of their resin-based composite (RBC). Ideally, future assessments and research publications should include the following information about the curing light: 1) radiant power output throughout the exposure cycle and the spectral radiant power as a function of wavelength, 2) analysis of the light beam profile and spectral emission across the light beam, and 3) measurement and reporting of the light the RBC specimen received as well as the output measured at the light tip.

Tooth Retrospective Dosimetry Using Electron Paramagnetic Resonance: Influence of Irradiated Dental Composites

In the aftermath of a major radiological accident, the medical management of overexposed individuals will rely on the determination of the dose of ionizing radiations absorbed by the victims. Because people in the general population do not possess conventional dosimeters, after the fact dose reconstruction methods are needed. Free radicals are induced by radiations in the tooth enamel of victims, in direct proportion to dose, and can be quantified using Electron Paramagnetic Resonance (EPR) spectrometry, a technique that was demonstrated to be very appropriate for mass triage. The presence of dimethacrylate based restorations on teeth can interfere with the dosimetric signal from the enamel, as free radicals could also be induced in the various composites used. The aim of the present study was to screen irradiated composites for a possible radiation-induced EPR signal, to characterize it, and evaluate a possible interference with the dosimetric signal of the enamel. We investigated the most common commercial composites, and experimental compositions, for a possible class effect. The effect of the dose was studied between 10 Gy and 100 Gy using high sensitivity X-band spectrometer. The influence of this radiation-induced signal from the composite on the dosimetric signal of the enamel was also investigated using a clinical L-Band EPR spectrometer, specifically developed in the EPR center at Dartmouth College. In X-band, a radiation-induced signal was observed for high doses (25-100 Gy); it was rapidly decaying, and not detected after only 24h post irradiation. At 10 Gy, the signal was in most cases not measurable in the commercial composites tested, with the exception of 3 composites showing a significant intensity. In L-band study, only one irradiated commercial composite influenced significantly the dosimetric signal of the tooth, with an overestimation about 30%. In conclusion, the presence of the radiation-induced signal from dental composites should not significantly influence the dosimetry for early dose assessment.

Hexaarylbiimidazoles as visible light thiol-ene photoinitiators

OBJECTIVES

The aim of this study is to determine if hexaarylbiimidazoles (HABIs) are efficient, visible light-active photoinitiators for thiol-ene systems. We hypothesize that, owing to the reactivity of lophyl radicals with thiols and the necessarily high concentration of thiol in thiol-ene formulations, HABIs will effectively initiate thiol-ene polymerization upon visible light irradiation.

METHODS

UV-vis absorption spectra of photoinitiator solutions were obtained using UV-vis spectroscopy, while EPR spectroscopy was used to confirm radical species generation upon HABI photolysis. Functional group conversions during photopolymerization were monitored using FTIR spectroscopy, and thermomechanical properties were determined using dynamic mechanical analysis.

RESULTS

The HABI derivatives investigated exhibit less absorptivity than camphorquinone at 469nm; however, they afford increased sensitivity at this wavelength when compared with bis(2,4,6-trimethylbenzoyl)-phenylphosphineoxide. Photolysis of the investigated HABIs affords lophyl radicals. Affixing hydroxyhexyl functional groups to the HABI core significantly improved solubility. Thiol-ene resins formulated with HABI photoinitiators polymerized rapidly upon irradiation with 469nm. The glass transition temperatures of the thiol-ene resin formulated with a bis(hydroxyhexyl)-functionalized HABI and photopolymerized at room and body temperature were 49.5±0.5°C and 52.2±0.1°C, respectively.

SIGNIFICANCE

Although thiol-enes show promise as continuous phases for composite dental restorative materials, they show poor reactivity with the conventional camphorquinone/tertiary amine photoinitiation system. Conversely, despite their relatively low visible light absorptivity, HABI photoinitiators afford rapid thiol-ene photopolymerization rates. Moreover, minor structural modifications suggest pathways for improved HABI solubility and visible light absorption.

Raman Spectroscopic Assessment of Degree of Conversion of Bulk-Fill Resin Composites – Changes at 24 Hours Post Cure

Objective

The aim of this study was to determine degree of conversion (DC) of solid and flowable bulk-fill composites immediately and after 24 hours and investigate the variations of DC at surface and depths up to 4 mm.

Materials and Methods

Eight bulk-fill composites (Tetric EvoCeram Bulk Fill [shades IVA and IVB], Quixfil, X-tra fil, Venus Bulk Fill, X-tra Base, SDR, Filtek Bulk Fill) were investigated, and two conventional composites (GrandioSO, X-Flow) were used as controls. The samples (n = 5) were cured for 20 seconds with irradiance of 1090 mW/cm2. Raman spectroscopic measurements were made immediately after curing on sample surfaces and after 24 hours of dark storage at surface and at incremental depths up to 4 mm. Mean DC values were compared using repeated measures analysis of variance (ANOVA) and t-test for dependent samples.

Results

Surface DC values immediately after curing ranged from 59.1%-71.8%, while the 24-hour postcure values ranged from 71.3%-86.1%. A significant increase of DC was observed 24 hours post cure for all bulk-fill composites, which amounted from 11.3% to 16.9%. Decrease of DC through depths up to 4 mm varied widely among bulk-fill composites and ranged from 2.9% to 19.7%.

Conclusions

All bulk-fill composites presented a considerable 24-hour postcure DC increase and clinically acceptable DC at depths up to 4 mm. Conventional control composites were sufficiently cured only up to 2 mm, despite significant postcure polymerization.

Bulk-Fill Resin Composites: Polymerization Contraction, Depth of Cure, and Gap Formation

The bulk-filling of deep, wide dental cavities is faster and easier than traditional incremental restoration. However, the extent of cure at the bottom of the restoration should be carefully examined in combination with the polymerization contraction and gap formation that occur during the restorative procedure. The aim of this study, therefore, was to compare the depth of cure, polymerization contraction, and gap formation in bulk-fill resin composites with those of a conventional resin composite. To achieve this, the depth of cure was assessed in accordance with the International Organization for Standardization 4049 standard, and the polymerization contraction was determined using the bonded-disc method. The gap formation was measured at the dentin margin of Class II cavities. Five bulk-fill resin composites were investigated: two high-viscosity (Tetric EvoCeram Bulk Fill, SonicFill) and three low-viscosity (x-tra base, Venus Bulk Fill, SDR) materials. Compared with the conventional resin composite, the high-viscosity bulk-fill materials exhibited only a small increase (but significant for Tetric EvoCeram Bulk Fill) in depth of cure and polymerization contraction, whereas the low-viscosity bulk-fill materials produced a significantly larger depth of cure and polymerization contraction. Although most of the bulk-fill materials exhibited a gap formation similar to that of the conventional resin composite, two of the low-viscosity bulk-fill resin composites, x-tra base and Venus Bulk Fill, produced larger gaps.

Effect of the irradiance distribution from light curing units on the local micro-hardness of the surface of dental resins

OBJECTIVE

An inhomogeneous irradiance distribution from a light-curing unit (LCU) can locally cause inhomogeneous curing with locally inadequately cured and/or over-cured areas causing e.g. monomer elution or internal shrinkage stresses, and thus reduce the lifetime of dental resin based composite (RBC) restorations. The aim of the study is to determine both the irradiance distribution of two light curing units (LCUs) and its influence on the local mechanical properties of a RBC.

METHODS

Specimens of Arabesk TOP OA2 were irradiated for 5, 20, and 80s using a Bluephase® 20i LCU in the Low mode (666mW/cm(2)), in the Turbo mode (2222mW/cm(2)) and a Celalux® 2 (1264mW/cm(2)). The degree of conversion (DC) was determined with an ATR-FTIR. The Knoop micro-hardness (average of five specimens) was measured on the specimen surface after 24h of dark and dry storage at room temperature.

RESULTS

The irradiance distribution affected the hardness distribution across the surface of the specimens. The hardness distribution corresponded well to the inhomogeneous irradiance distributions of the LCU. The highest reaction rates occurred after approximately 2s light exposure. A DC of 40% was reached after 3.6 or 5.7s, depending on the LCU. The inhomogeneous hardness distribution was still evident after 80s of light exposure.

SIGNIFICANCE

The irradiance distribution from a LCU is reflected in the hardness distribution across the surface. Irradiance level of the LCU and light exposure time do not affect the pattern of the hardness distribution--only the hardness level. In areas of low irradiation this may result in inadequate resin polymerization, poor physical properties, and hence premature failure of the restorations as they are usually much smaller than the investigated specimens. It has to be stressed that inhomogeneous does not necessarily mean poor if in all areas of the restoration enough light intensity is introduced to achieve a high degree of cure.

Green facile scalable synthesis of titania/carbon nanocomposites: new use of old dental resins

A green facile scalable method inspired by polymeric dental restorative composite is developed to synthesize TiO2/carbon nanocomposites for manipulation of the intercalation potential of TiO2 as lithium-ion battery anode. Poorly crystallized TiO2 nanoparticles with average sizes of 4-6 nm are homogeneously embedded in carbon matrix with the TiO2 mass content varied between 28 and 65%. Characteristic discharge/charge plateaus of TiO2 are significantly diminished and voltage continues to change along with proceeding discharge/charge process. The tap density, gravimetric and volumetric capacities, and cyclic and rate performance of the TiO2/C composites are effectively improved.

Advances in dental materials

The dental market is replete with new resorative materials marketed on the basis of novel technological advances in materials chemistry, bonding capability or reduced operator time and/or technique sensitivity. This paper aims to consider advances in current materials, with an emphasis on their role in supporting contemporary clinical practice.

The effect of ultra-fast photopolymerisation of experimental composites on shrinkage stress, network formation and pulpal temperature rise

OBJECTIVES

to complement our previous work by testing the null hypotheses that with short curing times and high DC, TPO-based resin composites would exhibit (1) higher polymerization stresses and consequently display (2) higher temperature rise and (3) higher flexural modulus, flexural strength and hardness, compared to a conventional CQ-based experimental composite.

METHODS

Two experimental resin composites using either Lucirin-TPO or camphorquinone/DMAEMA as photoinitiators were prepared. Light curing was carried out using spectral outputs adapted to the absorption properties of each initiator. Different irradiation protocols were selected (0.5, 1, 3, 9 s at 500, 1000 and 2000 mW/cm(2) for Lucirin-TPO based composites and 20 or 40 s at 1000 mW/cm2 for Lucirin-TPO and camphorquinone-based composites). Degree of conversion (DC) was measured in real time by means of FT-NIR spectroscopy. Pulpal temperature rise (ΔT) was studied in a tooth model. Polymerization stress was monitored using the Bioman instrument. For cured specimens, flexural modulus and flexural strength were determined using a three point bending platform and Vickers hardness was determined with a microhardness indentor on samples prior to and after 24 h incubation in 75/25 ethanol/H2O. Premolars were restored with both materials and microleakage at the teeth/composite interfaces following restoration was assessed.

RESULTS

Lucirin-TPO-based composites irradiated at radiant exposures of 3 J/cm(2) and more exhibited significantly higher DCs, associated with increased flexural moduli and hardness compared to CQ-based composites. For an ultra-short irradiation time of 1 s at 1000 mW/cm(2), TPO-composites displayed similar polymerization stresses compared to CQ-controls with yet a 25% increase for flexural modulus and 40% increase for hardness measured after EtOH/H2O sorption. Higher stress rates were however observed in all curing protocols compared to CQ-composites. Microleakage was similar between TPO and CQ-composites irradiated at 1000 mW/cm(2) for 3 and 20 s respectively, while a significant increase was observed for TPO-composites irradiated for 1 s. ΔT measured through a 0.6 mm thick dentin layer were all below 5.5°C; TPO-composites exhibited similar or lower values compared to controls.

SIGNIFICANCE

The use of Lucirin-TPO in resin composites along with appropriate curing conditions may allow for a major reduction of irradiation time while improving mechanical properties. The amount of stress observed during polymerization in TPO-based composites can be similar to those using CQ and the cohesion at the restoration-tooth interface was not affected by short curing times. Contrary to other studies, we found that the temperatures increases measured during polymerization were all well below the 5.5°C threshold for the pulp.

Influence of light-activation protocol on methacrylate resin-composite evaluated by dynamic mechanical analysis and degree of conversion

The aim of this study was to evaluate the degree of conversion (DC) and to identify the viscoelastic properties: storage modulus (E'), loss modulus (E"), tangent delta (tan δ), and glass transition temperature (T g ) of a microhybrid resin-composite light-activated by three different protocols. A Filtek Z250 (3 M ESPE) shade A3 was inserted in a Teflon mold (21 mm × 5 mm × 1 mm for viscoelastic properties; and 5 mm × 1 mm for DC) and light-activated according to the following light-activation protocols: (S) 1,000 mW/cm(2) × 19 s, (HP) 1,400 mW/cm(2) × 14 s, and (PE) 3,200 mW/cm(2) × 6 s, all set up to deliver 19 J/cm(2). Viscoelastic properties was assessed by dynamic mechanical analysis (DMA) (n = 3), performed in single cantilever clamped mode. DC (n = 5) was measured by FTIR on top (T) and bottom (B) surfaces, and the data was submitted to a split-plot one-way ANOVA. For DC, there was a significant effect for surface factor and light-activation protocols factor. Top surface showed higher DC than B in all experimental conditions. Light-activation protocols S and HP resulted in higher DC than PE and were similar between them. Viscoelastic properties (E', E", tan δ, T g ) were not affected by light-activation protocols. It could be concluded that light-activation protocols influenced DC but not influenced the viscoelastic properties.

Ultra-fast light-curing resin composite with increased conversion and reduced monomer elution

OBJECTIVES

To test the null hypotheses that photoactive resin composites containing a Type I photoinitiator would exhibit reduced DC or increased monomer elution at substantially short curing times compared with materials based on a Type 2 ketone/amine system.

METHODS

Two experimental resin composites were prepared, using either Lucirin-TPO or camphorquinone/DMAEMA. Specimens were light-cured using appropriate spectral emission that coincided with the absorption properties of each initiator using different irradiation protocols (0.5, 1, 3, 9s at 500, 1000 and 2000mW/cm(2) for Lucirin-TPO based composites and 20 or 40s at 1000mW/cm(2) for Lucirin-TPO and camphorquinone-based composites). Degree of conversion (DC) was measured by Raman spectroscopy, propagating radical concentrations were collected by means of electron paramagnetic resonance (EPR) and monomer leaching was characterized using high-performance liquid chromatography (HPLC).

RESULTS

The null hypotheses were rejected, except for a single irradiation protocol (0.5s @ 500mW/cm(2)). Lucirin-TPO-based composites could cure 20 times faster and release at least 4 times less monomers in comparison to camphorquinone-based composites. At 1000mW/cm(2), and 1s irradiation time for curing times of 1s, Lucirin-TPO based composites displayed 10% higher DC. The difference in polymerization efficiency of Lucirin-TPO compared with camphorquinone-based resin composites were explained using EPR; the former showing a significantly greater yield of radicals which varied logarithmically with radiant exposure.

SIGNIFICANCE

Lucirin-TPO is substantially more efficient at absorbing and converting photon energy when using a curing-light with an appropriate spectral emission and otherwise a limitation noted in several previous publications. At concentrations of 0.0134mol/L, Lucirin-TPO-based composites require a minimum light intensity of 1000mW/cm(2) and an exposure time of 1s to provide significantly improved DC and minimal elution compared with a conventional photoinitiator system. The use of a wide range of curing protocols in the current experiment has realized the significant potential of Lucirin-TPO and its impact for clinical applications, in replacement to materials using camphorquinone.

The reciprocity law concerning light dose relationships applied to BisGMA/TEGDMA photopolymers: theoretical analysis and experimental characterization

OBJECTIVES

A model BisGMA/TEGDMA unfilled resin was utilized to investigate the effect of varied irradiation intensity on the photopolymerization kinetics and shrinkage stress evolution, as a means for evaluation of the reciprocity relationship.

METHODS

Functional group conversion was determined by FTIR spectroscopy and polymerization shrinkage stress was obtained by a tensometer. Samples were polymerized with UV light from an EXFO Acticure with 0.1wt% photoinitiator. A one-dimensional kinetic model was utilized to predict the conversion-dose relationship.

RESULTS

As irradiation intensity increased, conversion decreased at a constant irradiation dose and the overall dose required to achieve full conversion increased. Methacrylate conversion ranged from 64±2% at 3mW/cm(2) to 78±1% at 24mW/cm(2) while the final shrinkage stress varied from 2.4±0.1MPa to 3.0±0.1MPa. The ultimate conversion and shrinkage stress levels achieved were dependent not only upon dose but also the irradiation intensity, in contrast to an idealized reciprocity relationship. A kinetic model was utilized to analyze this behavior and provide theoretical conversion profiles versus irradiation time and dose.

SIGNIFICANCE

Analysis of the experimental and modeling results demonstrated that the polymerization kinetics do not and should not be expected to follow the reciprocity law behavior. As irradiation intensity is increased, the overall dose required to achieve full conversion also increased. Further, the ultimate conversion and shrinkage stress that are achieved are not dependent only upon dose but rather upon the irradiation intensity and corresponding polymerization rate.

Reduced polymerization stress of MAPO-containing resin composites with increased curing speed, degree of conversion and mechanical properties

OBJECTIVES

The degree and rate of photopolymerization in resin-based dental composites will significantly affect polymer network formation and resultant material properties that may determine their clinical success. This study investigates the mechanical properties, the generation of stress from polymerization, tooth cusp deflection and marginal integrity of experimental resin composites that contain different photoinitiators.

METHODS

Experimental light-activated resin composites (60vol% particulate filled in 50/50mass% bis-GMA/TEGDMA) were formulated using a monoacylphosphine oxide (MAPO) photoinitiator and compared with a conventional camphoroquinone (CQ)-based system. Similar radiant exposure was used (18Jcm(-2)) for polymerization of each material although the curing protocol was varied (400mWcm(-2) for 45s, 1500mWcm(-2) for 12s and 3000mWcm(-2) for 6s). Degree and rate of polymerization was calculated in real-time by near infrared spectroscopy and the generation of stress throughout polymerization measured using a cantilever beam method. Flexural strength and modulus were acquired by three-point bend tests. Standardized cavities in extract pre-molar teeth were restored with each material, the total cuspal deflection measured and post-placement marginal integrity between the tooth and restoration recorded.

RESULTS

Generally, MAPO- exhibited a significantly higher degree of conversion (72±0.8 to 82±0.5%) compared with CQ-based materials (39±0.7 to 65±1.6%) regardless of curing protocol (p<0.05) and MAPO-based materials exhibited less difference in conversion between curing protocols. CQ-based materials exhibited between ∼85 and 95% of the maximum rate of polymerization at <15% conversion, whereas MAPO-based RBCs did not approach the maximum rate until >50% conversion. Higher irradiance polymerization had a significant deleterious effect on the mechanical properties of CQ-based materials (p<0.05) whereas MAPO-based materials exhibited increased strength and modulus and were less affected by the curing method. Total cuspal deflection in restored extracted teeth was higher for CQ- compared with MAPO-based materials cured at the lowest irradiance curing protocol (12.9±4.0 and 8.3±1.5μm) and similar at 3000mWcm(-1) for 6s (10.1±3.5 and 9.0±1.5μm). A significant decrease in marginal integrity was observed for CQ-based RBCs cured at high irradiance for short exposure time compared with that of the MAPO-based RBC cured using a similar protocol (p=0.037).

SIGNIFICANCE

Polymer network formation dictates the final properties of the set composite and the use MAPO photoinitiators may provide an effective restorative material that exhibits higher curing speeds, increased degree of conversion, strength and modulus without compromise in terms of polymerization stress and marginal integrity between tooth and restoration.

Localised irradiance distribution found in dental light curing units

OBJECTIVE

To measure the localised irradiance and wavelength distributions from dental light curing units (LCUs) and establish a method to characterise their output.

METHODS

Using a laboratory grade integrating sphere spectrometer system (Labsphere and Ocean Optics) the power, irradiance, and spectral emission were measured at the light tips of four LCUs: one plasma-arc (PAC) unit, one single peak blue light-emitting diode (blue-LED) unit, and two polywave LED (poly-LED) units. A beam profiler camera (Ophir Spiricon) was used to record the localised irradiance across the face of the light tips. The irradiance-calibrated beam profile images were then divided into 45 squares, each 1mm(2). Each square contained the irradiance information received from approximately 3200 pixels. The mean irradiance value within each square was calculated, and the distribution of irradiance values among these 45 squares across the tip-ends was examined. Additionally, the spectral emission was recorded at various regions across each light tip using the integrating sphere with a 4-mm diameter entrance aperture.

RESULTS

The localised irradiance distribution was inhomogeneous in all four lights. The irradiance distribution was most uniformly distributed across the PAC tip. Both the irradiance and spectral emission from the poly-LED units were very unevenly distributed.

CONCLUSIONS

Reporting a single irradiance value or a single spectral range to describe the output from a curing light is both imprecise and inappropriate. Instead, an image of both the irradiance distribution and the distribution of the spectral emission across the light tip should be provided.

CLINICAL SIGNIFICANCE

The localised beam irradiance profile at the tip of dental LCUs is not uniform. Poly-LED units may deliver spectrally inhomogeneous irradiance profiles. Depending on the photoinitiator used in the RBC and the orientation of the LCU over the tooth, this non-uniformity may cause inadequate and inhomogeneous resin polymerisation, leading to poor physical properties, and premature failure of the restoration.

Reproductive toxicity evaluation of the dental resin monomer bisphenol a glycidyl methacrylate (CAS 1565-94-2) in mice

The reproductive toxicity potential of the dental resin monomer bisphenol A glycidyl methacrylate (BisGMA; CASRN 1565-94-2) was investigated in male and female Crl: CD1(ICR) mice, 4 dosage groups, and 25 mice/sex/group. Formulations of BisGMA (0, 0.008, 0.08, or 0.8 mg/kg/d) in 0.8% ethanol in deionized water were intubated once daily beginning 28 days before cohabitation and continuing through mating (males) or through gestation day 17. The following parameters were evaluated: viability, clinical signs, body weights, estrous cyclicity, necropsy observations, organ weights, sperm concentration/motility/morphology, cesarean sectioning and litter observations, and histopathological evaluation of select tissues. No deaths or clinical signs related to BisGMA occurred. No significant changes in male and female body weights and body weight gains were recorded at any of the administered dosages of BisGMA. All mating and fertility parameters, and all litter and fetal data, were considered to be unaffected by dosages of BisGMA as high as 0.8 mg/kg/d. Gross or histopathologic tissue changes attributable to the test article were not observed. Reproductive and developmental no observed effect levels (NOAELs) for BisGMA were 0.8 mg/kg/d, the highest dose tested. Comparison of this NOAEL value to published probabilistic estimates of human BisGMA exposure from dental products suggests a margin of safety of at least 280- to nearly 2000-fold. Under the conditions of this study, BisGMA is not a reproductive toxicant.

Influence of free radicals signal from dental resins on the radio-induced signal in teeth in EPR retrospective dosimetry

In case of radiological accident, retrospective dosimetry is needed to reconstruct the absorbed dose of overexposed individuals not wearing personal dosimeters at the onset of the incident. In such a situation, emergency mass triage will be required. In this context, it has been shown that Electron Paramagnetic Resonance (EPR) spectroscopy would be a rapid and sensitive method, on the field deployable system, allowing dose evaluation of a great number of people in a short time period. This methodology uses tooth enamel as a natural dosimeter. Ionising radiations create stable free radicals in the enamel, in a dose dependent manner, which can be detected by EPR directly in the mouth with an appropriate resonator. Teeth are often subject to restorations, currently made of synthetic dimethacrylate-based photopolymerizable composites. It is known that some dental composites give an EPR signal which is likely to interfere with the dosimetric signal from the enamel. So far, no information was available about the occurrence of this signal in the various composites available on the market, the magnitude of the signal compared to the dosimetric signal, nor its evolution with time. In this study, we conducted a systematic characterization of the signal (intensity, kinetics, interference with dosimetric signal) on 19 most widely used composites for tooth restoration, and on 14 experimental resins made with the most characteristic monomers found in commercial composites. Although a strong EPR signal was observed in every material, a rapid decay of the signal was noted. Six months after the polymerization, the signal was negligible in most composites compared to a 3 Gy dosimetric signal in a tooth. In some cases, a stable atypical signal was observed, which was still interfering with the dosimetric signal.

Dynamic mechanical thermal analysis of composite resins with CQ and PPD as photo-initiators photoactivated by QTH and LED units

OBJECTIVES

The aim of this study was to evaluate the thermal and mechanical properties of the composite resins containing the photo-initiators camphorquinone (CQ) and/or phenyl-propanodione (PPD) when photoactivated with halogen lamp (XL2500/3M-ESPE), monowave (UltraBlueIS/DMC) and polywave (UltraLume5/Ultradent) LED units.

MATERIALS AND METHODS

A blend of BisGMA, UDMA, BisEMA and TEGDMA was prepared with the same wt% of photo-initiators CQ and/or PPD and 65wt% of silaneted filler particles. Compression strength (CS), diametral tensile strength (DTS) and diametral modulus (DM) were tested. Thermogravimetric analysis (TGA) was made and the lost residual monomer were verified. Dynamic mechanical thermal analysis (DMTA) was used for to analyze the glass transition temperature (Tg) and the storage modulus in 37°C. Degree of conversion (DC) was accomplished in the same samples of DMA using middle-infrared spectroscopy (mid-IR).

RESULTS

CQ, CQ/PPD and PPD obtained the same results for all mechanical properties (CS, DTS and DM), lost residual monomer and storage modulus in 37°C, regardless LCU used. The results of Tg showed that the combination PPD-UltraLume5 produced the highest values. DC showed that the combination CQ-UltraLume5 resulted in the highest values and PPD-XL2500 in the lowest DC values.

CONCLUSION

The study shows that PPD is not only effective photosensitizers, but also photocrosslinking agents for dental composite resins with a similar efficiency to CQ.