Modification of Si(100) surface by the grafting of poly(ethylene glycol) for reduction in protein adsorption and platelet adhesion

Droplet Spreading Characteristics on Ultra-Slippery Solid Hydrophilic Surfaces with Ultra-Low Contact Angle Hysteresis

Dynamic interactions of the droplet impact on a solid surface are essential to many emerging applications, such as electronics cooling, ink-jet printing, water harvesting/collection, anti-frosting/icing, and microfluidic and biomedical device applications. Despite extensive studies on the kinematic features of the droplet impact on a surface over the last two decades, the spreading characteristics of the droplet impact on a solid hydrophilic surface with ultra-low contact angle hysteresis are unclear. This paper clarifies the specific role of the contact angle and contact angle hysteresis at each stage of the droplet impact and spreading process. The spreading characteristics of the droplet impact on an ultra-slippery hydrophilic solid surface are systematically compared with those on plain hydrophilic, hydroxylated hydrophilic, and plain hydrophobic surfaces. The results reveal that the maximum spreading factor (βmax) of impacting droplets is mainly dependent on the contact angle and We. βmax increases with the increase in We and the decrease in the contact angle. Low contact angle hysteresis can decrease the time required to reach the maximum spreading diameter and the time interval during which the maximum spreading diameter is maintained when the contact angles are similar. Moreover, the effect of the surface inclination angle on the spreading and slipping dynamics of impacting droplets is investigated. With the increase in the inclination angle and We, the gliding distance of the impacting droplet becomes longer. Ultra-low contact angle hysteresis enables an impacting droplet to slip continuously on the ultra-slippery hydrophilic surface without being pinned to the surface. The findings of this work not only show the important role of the surface wettability in droplet spreading characteristics but also present a pathway to controlling the dynamic interactions of impacting droplets with ultra-slippery hydrophilic surfaces.

Marine antifouling performance of polymer coatings incorporating zwitterions

Zwitterionic materials display antifouling promise, but their potential in marine anti-biofouling is still largely unexplored. This study evaluates the effectiveness of incorporating small quantities (0-20% on a molar basis) of zwitterions as sulfobetaine methacrylate (SBMA) or carboxybetaine methacrylate (CBMA) into lauryl methacrylate-based coatings whose relatively hydrophobic nature encourages adhesion of the diatom Navicula incerta, a common microfouling organism responsible for the formation of 'slime'. This approach allows potential enhancements in antifouling afforded by zwitterion incorporation to be easily quantified. The results suggest that the incorporation of CBMA does provide a relatively minor enhancement in fouling-release performance, in contrast to SBMA which does not display any enhancement. Studies with coatings incorporating mixtures of varying ratios of the cationic monomer [2-(methacryloyloxy)ethyl]trimethylammonium chloride and the anionic monomer (3-sulfopropyl)methacrylate, which offer a potentially lower cost approach to the incorporation of anionic and cationic charge, suggest these monomers impart little significant effect on biofouling.

Modulating Immunological Responses of Electrospun Fibers for Tissue Engineering

The promise of tissue engineering is to improve or restore functions of impaired tissues or organs. However, one of the biggest challenges to its translation to clinical applications is the lack of tissue integration and functionality. The plethora of cellular and molecular events occurring following scaffold implantation is a major bottleneck. Recent studies confirmed that inflammation is a crucial component influencing tissue regeneration. Immuno-modulation or immune-engineering has been proposed as a potential solution to overcome this key challenge in regenerative medicine. In this review, strategies to modify scaffold physicochemical properties through the use of the electrospinning technique to modulate host response and improve scaffold integration will be discussed. Electrospinning, being highly versatile allows the fabrication of ECM-mimicking scaffolds and also offers the possibility to control scaffold properties for instance, tailoring of fiber properties, chemical conjugation or physical adsorption of non-immunogenic materials on the scaffold surface, encapsulating cells or anti-inflammatory molecules within the scaffold. Such electrospun scaffold-based immune-engineering strategies can significantly improve the resulting outcomes of tissue engineering scaffolds.

Protein diffusion characteristics in the hydrogels of poly(ethylene glycol) and zwitterionic poly(sulfobetaine methacrylate) (pSBMA)

Nonfouling materials such as neutral poly(ethylene glycol) (PEG) and zwitterionic poly(sulfobetaine methacrylate) (pSBMA) are ideal biocompatible materials for drug, especially protein drug delivery. The interaction behavior of protein between the nonfouling materials could cause great impact on their future applications, such as controlled release drug delivery systems. In this work, we investigated the diffusion behavior of the fluorescence-labeled model proteins (bovine serum albumin (BSA) and lysozyme (LYZ)) in nonfouling PEG, pSBMA and mixed PEG-SBMA hydrogels (SBMA:PEG 4:1, SBMA:PEG 1:4). It was observed that these four hydrogels showed varied diffusion behavior for either negatively charged BSA or positively charged LYZ due to protein-polymer interaction and the free water content in hydrogel matrix. The relatively stronger interaction between protein-PEG than protein-pSBMA could increase protein loading efficiency and control release rate by changing ratio of PEG to SBMA in the hybrid hydrogel. Moreover, it is further demonstrated the free water (freezable water) content in low cross-linked hydrogel, not the equilibrium water content (EWC), is a more accurate parameter to reflect the diffusion behavior of protein molecules. Thus, these results together provide new insights of the interactions between protein molecules and nonfouling polymers as well as the bio applications of the nonfouling polymeric hydrogels.

STATEMENT OF SIGNIFICANCE

This work shows that the relative stronger interaction between protein-PEG than protein-pSBMA could increase protein loading efficiency and control release rate by the change ratio of PEG to SBMA in the hydrogel, while the free water (freezable water) content in low cross-linked hydrogel, not the equilibrium water content (EWC), is a more accurate parameter to reflect the diffusion behavior of protein molecules. The impact of this work (i) gains some new insights of the interactions between protein molecules and nonfouling polymer matrixes for protein drug delivery; (ii) prompts to apply the weak PEG-protein interactions to protein drug loading and release; (iii) provides a new fundamental understanding of free water in hydrogel for protein diffusion.

Update on Renal Replacement Therapy: Implantable Artificial Devices and Bioengineered Organs

Recent advances in the fields of artificial organs and regenerative medicine are now joining forces in the areas of organ transplantation and bioengineering to solve continued challenges for patients with end-stage renal disease. The waiting lists for those needing a transplant continue to exceed demand. Dialysis, while effective, brings different challenges, including quality of life and susceptibility to infection. Unfortunately, the majority of research outputs are far from delivering satisfactory solutions. Current efforts are focused on providing a self-standing device able to recapitulate kidney function. In this review, we focus on two remarkable innovations that may offer significant clinical impact in the field of renal replacement therapy: the implantable artificial renal assist device (RAD) and the transplantable bioengineered kidney. The artificial RAD strategy utilizes micromachining techniques to fabricate a biohybrid system able to mimic renal morphology and function. The current trend in kidney bioengineering exploits the structure of the native organ to produce a kidney that is ready to be transplanted. Although these two systems stem from different technological approaches, they are both designed to be implantable, long lasting, and free standing to allow patients with kidney failure to be autonomous. However, for both of them, there are relevant issues that must be addressed before translation into clinical use and these are discussed in this review.

Double network hydrogels from polyzwitterions: high mechanical strength and excellent anti-biofouling properties

Polyzwitterionic materials, which have both cationic and anionic groups in the polymeric repeat unit, show excellent anti-biofouling properties and are drawing more attention in the biomedical field. In this study, we have successfully synthesized novel single network hydrogels and double network (DN) hydrogels from the zwitterionic monomer, N-(carboxymethyl)-N,N-dimethyl-2-(methacryloyloxy) ethanaminium, inner salt (CDME). The polyCDME (PCDME) single network hydrogel behaves like a hydrophilic neutral hydrogel and its properties are not sensitive to temperature, pH, or ionic strength over a wide range. DN hydrogels using the poly(2-acrylamido-2-methylpropanesulfonic) (PAMPS) as the first network and PCDME as the second network, having a Young's modulus of 0.2-0.9 MPa, possess excellent mechanical strength (fracture stress: 1.2-1.4 MPa, fracture strain: 2.2-6.0 mm/mm) and toughness (work of extension at fracture: 0.9-2.4 MJ m^-3) depending on the composition ratio of PCDME to PAMPS. The strength and toughness of the optimized PAMPS/PCDME DN is comparable to the normal PAMPS/PAAm DN hydrogels that use poly(acrylamide) (PAAm) as the second network. By macrophage adhesion test, both the PCDME hydrogels and the PAMPS/PCDME DN hydrogels have shown excellent anti-biofouling properties. These results demonstrate that the PCDME-based DN hydrogels have high potential as a novel soft and wet biomaterial.

Hemocompatibility of silicon-based substrates for biomedical implant applications

Silicon membranes with highly uniform nanopore sizes fabricated using microelectromechanical systems (MEMS) technology allow for the development of miniaturized implants such as those needed for renal replacement therapies. However, the blood compatibility of silicon has thus far been an unresolved issue in the use of these substrates in implantable biomedical devices. We report the results of hemocompatibility studies using bare silicon, polysilicon, and modified silicon substrates. The surface modifications tested have been shown to reduce protein and/or platelet adhesion, thus potentially improving biocompatibility of silicon. Hemocompatibility was evaluated under four categories—coagulation (thrombin–antithrombin complex, TAT generation), complement activation (complement protein, C3a production), platelet activation (P-selectin, CD62P expression), and platelet adhesion. Our tests revealed that all silicon substrates display low coagulation and complement activation, comparable to that of Teflon and stainless steel, two materials commonly used in medical implants, and significantly lower than that of diethylaminoethyl (DEAE) cellulose, a polymer used in dialysis membranes. Unmodified silicon and polysilicon showed significant platelet attachment; however, the surface modifications on silicon reduced platelet adhesion and activation to levels comparable to that on Teflon. These results suggest that surface-modified silicon substrates are viable for the development of miniaturized renal replacement systems.

Self-assembly of poly(ethylene glycol)-poly(alkyl phosphonate) terpolymers on titanium oxide surfaces: synthesis, interface characterization, investigation of nonfouling properties, and long-term stability

This contribution deals with the self-assembling of a terpolymer on titanium oxide (TiO(2)) surface. The polymer structure was obtained by polymerization of different methacrylates, i.e., alkyl-phosphonated, butyl and PEG methacrylate, in the presence of a chain transfer agent. The resulting PEG-poly(alkyl phosphonate) material, characterized mainly by SEC and NMR, self-organized at the interface of TiO(2). AR-XPS demonstrated the binding of phosphonate groups to TiO(2) substrate and the formation of a PEG-brush layer at the outermost part of the system. The stability of this terpolymer adlayer, after exposure to solutions of pH 2, 7.4, and 9 up to 3 weeks, was evaluated quantitatively by XPS and ellipsometry. We demonstrated an overall stability improvements of this coating against desorption in contact with aqueous solutions in comparison with reference self-assembly systems. Finally, the PEG-terpolymer adlayer proved to impart to TiO(2) substrate antifouling properties when exposed to full blood serum.

Poly(ethylene glycol) monolayer formation and stability on gold and silicon nitride substrates

Poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) are extensively used to modify substrates to prevent nonspecific protein adsorption and to increase hydrophilicity. X-ray photoelectron spectroscopy analysis, complemented by water contact angle measurements, is employed to investigate the formation and stability upon aging and heating of PEG monolayers formed on gold and silicon nitride substrates. In particular, thiolated PEG monolayers on gold, with and without the addition of an undecylic spacer chain, and PEG monolayers formed with oxysilane precursors on silicon nitride have been probed. It is found that PEG-thiol SAMs are degraded after less than two weeks of exposure to air and when heated at temperatures as low as 120 degrees C. On the contrary, PEG-silane SAMs are stable for more than two weeks, and fewer molecules are desorbed even after two months of aging, compared to those desorbed in two weeks from the PEG-thiol SAMs. A strongly bound hydration layer is found on PEG-silane SAMs aged for two months. Heating PEG-silane SAMs to temperatures as high as 160 degrees C improves the quality of the monolayer, desorbing weakly bound contaminants. The differences in stability between PEG-thiol SAMs and PEG-silane SAMs are ascribed to the different types of bonding to the surface and to the fact that the thiol-Au bond can be easily oxidized, thus causing desorption of PEG molecules from the surface.

PEGMA/MMA copolymer graftings: generation, protein resistance, and a hydrophobic domain

We synthesized various graft copolymer films of poly(ethylene glycol) methacrylate (PEGMA) and methyl methacrylate (MMA) on silicon to examine the dependency of protein-surface interactions on grafting composition. We optimized atom transfer radical polymerizations to achieve film thicknesses from 25 to 100 nm depending on the monomer mole fractions, and analyzed the resulting surfaces by X-ray photoelectron spectroscopy (XPS), ellipsometry, contact angle measurements, and atomic force microscopy (AFM). As determined by XPS, the stoichiometric ratios of copolymer graftings correlated with the concentrations of provided monomer solutions. However, we found an unexpected and pronounced hydrophobic domain on copolymer films with a molar amount of 10-40% PEGMA, as indicated by advancing contact angles of up to 90 degrees . Nevertheless, a breakdown of the protein-repelling character was only observed for a fraction of 15% PEGMA and lower, far in the hydrophobic domain. Investigation of the structural basis of this exceptional wettability by high-resolution AFM demonstrated the independence of this property from morphological features.

A novel glass slide-based peptide array support with high functionality resisting non-specific protein adsorption

Glass slides have been modified with a multifunctional poly(ethylene glycol) (PEG)-based polymer with respect to array applications in the growing field of proteome research. We systematically investigated the stepwise synthesis of the PEG films starting from self-assembled alkyl silane monolayers via monolayer peroxidation and subsequent graft polymerization of PEG methacrylate (PEGMA). Chemical composition was examined by X-ray photoelectron spectroscopy (XPS); infrared spectroscopy provided information about order and composition of the films as well; film thickness was determined by ellipsometry; using fluorescence microscopy and again XPS, the amount of proteins adsorbed on the slides was investigated. The novel support material allows a versatile modification of the amino group surface density up to 40 nmol/cm(2) for the linkage of probe molecules. Further on, we carried out standard peptide synthesis based on the well-established 9-fluorenylmethoxycarbonyl (Fmoc) chemistry, which was monitored by UV/Vis quantification of the Fmoc deblocking and mass spectrometry. The polymer coating is stable with respect to a wide range of chemical and thermal conditions, and prevents the glass surface from unspecific protein adsorption. Finally, we applied our modified glass slides in immunoassays and thus examined specific interactions of monoclonal antibodies with appropriate peptide epitopes.

Heparin-coupled poly(poly(ethylene glycol) monomethacrylate)-Si(111) hybrids and their blood compatible surfaces

Well-defined (nearly monodispersed) poly(poly(ethylene glycol)monomethacrylate)-Si hybrids were prepared via surface-initiated atom transfer radical polymerization (ATRP) of the poly(ethylene glycol)monomethacrylate (PEGMA) macromonomer on the hydrogen-terminated Si(111) surface (Si-H surface). Both the active chloride groups at the chain ends (from the ATRP process) and the chloride groups converted from some ( approximately 32%) of the -OH groups of the Si-C bonded PEGMA polymer, or P(PEGMA), brushes were used as leaving groups for the covalent coupling of heparin. For the heparinized P(PEGMA)-Si hybrid surfaces, protein adsorption and platelet adhesion were significantly suppressed. The well-defined and dense P(PEGMA) brushes, prepared from surface-initiated ATRP, had allowed the immobilization of a relatively high concentration of heparin (about 14 mug/cm(2)). The resulting silicon surface exhibited significantly improved antithrombogenecity with a plasma recalcification time (PRT) of about 150 min. The persistence of high bioactivity for the immobilized heparin on the hybrid surfaces can be attributed to the biocompatibility of the PEGMA units, as well as their role as spacers in providing the immobilized heparin with a higher degree of conformational freedom in a more hydrophilic environment. Thus, the heparin-coupled P(PEGMA)-Si hybrids with anti-fouling and antithrombogenic surfaces are potentially useful in silicon-based implantable devices and tissue engineering.

Poly(N-acryloylsarcosine methyl ester) Protein-Resistant Surfaces

A new class of protein-resistant film based on N-substituted glycine derivatives is described. Pulsed plasma deposited poly(N-acryloylsarcosine methyl ester) coatings are shown to be resistant toward the adsorption of fibrinogen and lysozyme. Deposition and UV irradiation of the polymer through a masked grid are found to be effective ways for generating negative and positive image protein arrays, respectively, onto a range of different substrate materials.

XPS and AFM analysis of antifouling PEG interfaces for microfabricated silicon biosensors

In the past two decades, the biological and medical fields have seen great advances in the development of biosensors capable of quantifying biomolecules. Many of these biosensors have micro- and nano-scale features, are fabricated using biochip technology, and use silicon as a base material. The creation of antifouling sensor interfaces is critical to avoid serious consequences that arise due to their contact with biological fluids. To this end, we have created thin PEG interfaces of various grafting densities on silicon using a single-step PEG-silane coupling reaction scheme. Initial PEG concentration (5-50 mM) and coupling time (0.5-24 h) were varied to attain different grafting densities, and different PEG interfaces so created were analyzed using XPS and AFM. Furthermore, all the PEG interfaces were evaluated using XPS and AFM for their antifouling abilities using fibrinogen as the model protein. Results indicated that PEG interfaces created in this investigation are appropriate for biosensors with micro- and nano-scale features, and are efficient in controlling protein fouling.

Multiphoton microscopy guides neurotrophin modification with poly(ethylene glycol) to enhance interstitial diffusion

Brain-derived neurotrophic factor (BDNF) is a promising therapeutic agent for the treatment of neurodegenerative diseases. However, the limited distribution of this molecule after administration into the brain tissue considerably hampers its efficacy. Here, we show how multiphoton microscopy of fluorescently tagged BDNF in brain-tissue slices provides a useful and rapid screening method for examining the diffusion of large molecules in tissues, and for studying the effects of chemical modifications-for example, conjugating with polyethylene glycol (PEG)-on the diffusion constant. This single variable, obtained by monitoring short-term diffusion in real time, can be effectively used for rational drug design. In this study on fluorescently tagged BDNF and BDNF-PEG, we identify slow diffusion as a major contributing factor to the limited penetration of BDNF, and demonstrate how chemical modification can be used to overcome this barrier.

Evaluation of the stability of nonfouling ultrathin poly(ethylene glycol) films for silicon-based microdevices

The creation of nonfouling surfaces is one of the major prerequisites for microdevices for biomedical and analytical applications. Poly(ethylene glycol) (PEG), a water soluble, nontoxic, and nonimmunogenic polymer has the unique ability of reducing nonspecific protein adsorption and cell adhesion and, therefore, is generally coupled with a wide variety of surfaces to improve their biocompatibility. The performance of these modified surfaces for long-term biomedical applications largely depends on the stability of these PEG films. To this end, we have investigated the stability of covalently coupled ultrathin PEG films on silicon in aqueous in vivo like conditions for a period of 4 weeks. The PEG-modified silicon substrates were incubated in PBS (37 degrees C, pH 7.4, 5% CO2) for different periods of time and then characterized using the techniques of ellipsometry, contact angle measurement, X-ray photoelectron spectroscopy, and atomic force microscopy. The ability of the PEG-modified surfaces to control protein fouling was examined by protein adsorption studies using fluorescein isothiocyanate labeled bovine serum albumin and ellipsometry. Furthermore, the ability of these films to control fibroblast adhesion was examined. Studies suggest that the PEG-modified surfaces retain their protein and cell repulsive nature even though the PEG film thickness decreases for the period of investigation.

Solid supports for microarray immunoassays

Stimulated by the achievements of the first phase in genomics and the resulting need of assigning functions to the acquired sequence information, novel formats of immunoassays are being developed for high-throughput multi-analyte studies. In principle, they are similar in nature to the microarray assays already established at the level of nucleic acids. However, the biochemical diversity and the sheer number of proteins are such that an equivalent analysis is much more complex and thus difficult to accomplish. The wide range of protein concentration complicates matters further. Performing microarray immunoassays already represents a challenge at the level of preparing a working chip surface. Arrays have been produced on filter supports, in microtiter plate wells and on glass slides, the last two usually coated with one-, two- or three-dimensionally structured surface modifications. The usefulness and suitability of all these support media for the construction and application of antibody microarrays are reviewed in this manuscript in terms of the different kinds of immunoassay and the various detection procedures. Additionally, the employment of microarrays containing alternative sensor molecules is discussed in this context. The sensitivity of microspot immunoassays predicted by the current analyte theory is not yet a reality, indicating the extent of both the technology's potential and the size of the task still ahead.

Functionalization of poly-L-lactic-co-ε-caprolactone: effects of surface modification on endothelial cell proliferation and hemocompatibility

A copolymer of L-lactic acid and epsilon-caprolactone (PLLACL) was synthesized with the aim of preparing a bioartificial, small-diameter and partially resorbable vascular graft. The material was submitted to surface functionalizations (i.e. chemical modification by means of hydrolytic 'etching' and plasma discharge) to promote endothelial cell (EC) adhesion and growth avoiding platelet adhesion or coagulation factor absorption. Furthermore, the behaviour of human microvascular endothelial cells (HMVEC) seeded on the untreated and treated copolymer is described, as well as the platelet adhesion and the modifications of coagulation factors determined by the copolymer itself. PLLACL in its native state provided little support for EC adhesion. Improved EC adherence was obtained when functional groups were provided on the polymer surface by surface chemical hydrolysis. HMVEC seeded and cultured on the polymer surface did not show any ultrastructural alteration, thus demonstrating the absence of the polymer cytotoxicity. Moreover, SEM analysis performed on cold plasma modified specimens showed the presence of a subconfluent monolayer of EC, with an elongated spread morphology. Both the untreated and treated copolymers induced only slight variations of platelet number, but determined the activated partial thromboplastin time (APTT) increase, due to factor XI reduction. Finally, a prototype of partially biodegradable vascular prosthesis was prepared with NaOH/HCl-treated copolymer. Pre-cultured HMVEC seeding of the prosthesis by means of a rotation device resulted in an almost completely coverage of the graft inner surface.