Facile shape control of Co(3)O(4) and the effect of the crystal plane on electrochemical performance

Activating Inert Crystal Face via Facet-Dependent Quench-Engineering for Electrocatalytic Water Oxidation

Developing a facile strategy to activate the inert crystal face of an electrocatalyst is critical to full-facet utilization, yet still challenging. Herein, the electrocatalytic activity of the inert crystal face is activated by quenching Co3O4 cubes and hexagonal plates with different crystal faces in Fe(NO3)3 solution, and the regulation mechanism of facet-dependent quench-engineering is further revealed. Compared to the Co3O4 cube with exposed {100} facet, the Co3O4 hexagonal plate with exposed {111} facet is more responsive to quenching, accompanied by a rougher surface, richer defect, and more Fe doping. Theoretical calculations indicate that the {111} facet has a more open structure with lower defect formation energy and Fe doping energy, ensuring its electronic and coordination structure is easier to optimize. Therefore, quench-engineering largely increases the catalytic activity of {111) facet for oxygen evolution reaction by 13.2% (the overpotential at 10 mA cm-2 decreases from 380 to 330 mV), while {100} facet only increases by 7.6% (from 393 to 363 mV). The quenched Co3O4 hexagonal plate exhibits excellent electrocatalytic activity and stability in both zinc-air battery and water-splitting. The work reveals the influence mechanism of crystal face on quench-engineering and inspires the activation of the inert crystal face.

Constructing core-shell structured Co3O4-MnWO4 composite photoelectrode with superior PEC water purification performance

Semiconductor photoelectrocatalytic (PEC) technology is one of the most effective methods for removing organic pollutants from wastewater in advanced oxidation processes(AOPs). The selection of suitable semiconductor materials as photoanodes is a crucial factor for achieving superior PEC performance. Here, a core-shell structured Co3O4-MnWO4 architecture is created by enveloping MnWO4 nanoparticles onto the surface of Co3O4 nanowires through a two-step hydrothermal process. The optimized Co3O4-MnWO4-5 photoelectrode showed superior PEC degradation efficiency for KN-R (∼91.2% in 2 h) and durable stability (the accelerated lifetime reached ∼9100 s at a current density of 50 mA cm-2). Three actual wastewaters were also collected to verify the practical applicability of the photoelectrode.The energy consumption was measured at 4.48 kWhm-3, with a COD removal efficiency of 83% and a decolorization rate of 98%. These results demonstrate the excellent performance and promising application of the photoelectrode. The enhancement of PEC performance for the core-shell structured Co3O4-MnWO4 architecture can be attributed to the suitable energy band structure of the Co3O4-MnWO4 composite, higher OEP, larger electrochemical active surface area, accelerated transport of interface carriers, and lower charge transfer resistance. The energy band structure of the Co3O4-MnWO4 composite showed a strong redox ability to induce electrons/holes (e-/h+), which enhances the generation of intermediate active species (hydroxyl radical ·OH and superoxide radicals ·O2-). Therefore, the rationally designed core-shell structured Co3O4-MnWO4 architecture exhibited excellent practical applicability in the degradation of organic pollutants.

Utilizing the oxygen-atom trapping effect of Co3O4 with oxygen vacancies to promote chlorite activation for water decontamination

Heterogeneous high-valent cobalt-oxo [≡Co(IV)=O] is a widely focused reactive species in oxidant activation; however, the relationship between the catalyst interfacial defects and ≡Co(IV)=O formation remains poorly understood. Herein, photoexcited oxygen vacancies (OVs) were introduced into Co3O4 (OV-Co3O4) by a UV-induced modification method to facilitate chlorite (ClO2-) activation. Density functional theory calculations indicate that OVs result in low-coordinated Co atom, which can directionally anchor chlorite under the oxygen-atom trapping effect. Chlorite first undergoes homolytic O-Cl cleavage and transfers the dissociated O atom to the low-coordinated Co atom to form reactive ≡Co(IV)=O with a higher spin state. The reactive ≡Co(IV)=O rapidly extracts one electron from ClO2- to form chlorine dioxide (ClO2), accompanied by the Co atom returning a lower spin state. As a result of the oxygen-atom trapping effect, the OV-Co3O4/chlorite system achieved a 3.5 times higher efficiency of sulfamethoxazole degradation (~0.1331 min-1) than the pristine Co3O4/chlorite system. Besides, the refiled OVs can be easily restored by re-exposure to UV light, indicating the sustainability of the oxygen atom trap. The OV-Co3O4 was further fabricated on a polyacrylonitrile membrane for back-end water purification, achieving continuous flow degradation of pollutants with low cobalt leakage. This work presents an enhancement strategy for constructing OV as an oxygen-atom trapping site in heterogeneous advanced oxidation processes and provides insight into modulating the formation of ≡Co(IV)=O via defect engineering.

Microwave-Assisted Hydrothermal Synthesis of {100} and {111} Faceted LiFeO2 Truncated Octahedra: Investigations on Volatile Organic Compound Sensing Performance

Growth of exposed crystal facets has received considerable attention because of their coordinatively unsaturated surface atoms and defect-related surface reactivities. Herein, LiFeO2 truncated octahedra exposed with 6 {100} facets and 8 {111} facets were prepared through a simple microwave-assisted hydrothermal method without using any additives, surfactants, and calcination processes. The detailed growth process revealed that the formation of LiFeO2 truncated octahedra occurred only at the optimized reaction temperature (180 °C), time (30 min), and reactant concentrations. The prepared LiFeO2 truncated octahedra showed excellent sensing responses toward aliphatic organic compounds compared to that against aromatic organic compounds and poor response to inorganic compounds. The response percentages of 150 ppm concentrations of acetone, ethanol, formaldehyde, and isopropyl alcohol are 81.84, 62.91, 62.68, and 69.41%, respectively, at a low operating temperature (100 °C). The presence of exposed facets with their coordinatively unsaturated Li/Fe surface atoms such as 5-fold {100}, 3-fold {111}, 3-fold {100}-{111}, 2-fold {111}-{111}, and 2-fold coordination with the O atom in the vertices facilitated more oxygen vacancies and led to improved surface reactivities as well as sensitivity.

Role of Fe decoration on the oxygen evolving state of Co3O4 nanocatalysts

The production of green hydrogen through alkaline water electrolysis is the key technology for the future carbon-neutral industry. Nanocrystalline Co3O4 catalysts are highly promising electrocatalysts for the oxygen evolution reaction and their activity strongly benefits from Fe surface decoration. However, limited knowledge of decisive catalyst motifs at the atomic level during oxygen evolution prevents their knowledge-driven optimization. Here, we employ a variety of operando spectroscopic methods to unveil how Fe decoration increases the catalytic activity of Co3O4 nanocatalysts as well as steer the (near-surface) active state formation. Our study shows a link of the termination-dependent Fe decoration to the activity enhancement and a significantly stronger Co3O4 near-surface (structural) adaptation under the reaction conditions. The near-surface Fe- and Co-O species accumulate an oxidative charge and undergo a reversible bond contraction during the catalytic process. Moreover, our work demonstrates the importance of low coordination surface sites on the Co3O4 host to ensure an efficient Fe-induced activity enhancement, providing another puzzle piece to facilitate optimized catalyst design.

Crystal Plane Engineering to Boost Water Cluster Evaporation for Enhanced Solar Steam Generation

Polymer based low evaporation enthalpy materials have become a universal selection for improving the efficiency of solar steam generation. Although water cluster and intermediate water mechanisms have been proposed to explain the low evaporation enthalpy, the production process and microstructure of activated water are still unclear. Here, crystal plane engineering is used to investigate the intermediate water state and the water cluster activation mechanism. The unique open-closed coordination structure on the optimized crystal surface promotes the generation of firm water clusters by optimizing the intermediate water state. Under the similar solar energy absorption of all materials, crystal plane engineering increased the solar steam generation rate of the evaporator by 31.2% and increased the energy efficiency to 94.8%. Exploring the micro-evaporation process and activated water structure is expected to stimulate the development of the next generation low evaporation enthalpy materials.

Probing spin waves in Co3O4 nanoparticles for magnonics applications

The magnetic properties of spinel nanoparticles can be controlled by synthesizing particles of a specific shape and size. The synthesized nanorods, nanodots and cubic nanoparticles have different crystal planes selectively exposed on the surface. The surface effects on the static magnetic properties are well documented, while their influence on spin waves dispersion is still being debated. Our ability to manipulate spin waves using surface and defect engineering in magnetic nanoparticles is the key to designing magnonic devices. We synthesized cubic and spherical nanoparticles of a classical antiferromagnetic material Co3O4 to study the shape and size effects on their static and dynamic magnetic proprieties. Using a combination of experimental methods, we probed the magnetic and crystal structures of our samples and directly measured spin wave dispersions using inelastic neutron scattering. We found a weak, but unquestionable, increase in exchange interactions for the cubic nanoparticles as compared to spherical nanoparticle and bulk powder reference samples. Interestingly, the exchange interactions in spherical nanoparticles have bulk-like properties, despite a ferromagnetic contribution from canted surface spins.

Fabrication and Characterization of Dielectric ZnCr2O4 Nanopowders and Thin Films for Parallel-Plate Capacitor Applications

We report here the successful shape-controlled synthesis of dielectric spinel-type ZnCr2O4 nanoparticles by using a simple sol-gel auto-combustion method followed by successive heat treatment steps of the resulting powders at temperatures from 500 to 900 °C and from 5 to 11 h, in air. A systematic study of the dependence of the morphology of the nanoparticles on the annealing time and temperature was performed by using field effect scanning electron microscopy (FE-SEM), powder X-ray diffraction (PXRD) and structure refinement by the Rietveld method, dynamic lattice analysis and broadband dielectric spectrometry, respectively. It was observed for the first time that when the aerobic post-synthesis heat treatment temperature increases progressively from 500 to 900 °C, the ZnCr2O4 nanoparticles: (i) increase in size from 10 to 350 nm and (ii) develop well-defined facets, changing their shape from shapeless to truncated octahedrons and eventually pseudo-octahedra. The samples were found to exhibit high dielectric constant values and low dielectric losses with the best dielectric performance characteristics displayed by the 350 nm pseudo-octahedral nanoparticles whose permittivity reaches a value of ε = 1500 and a dielectric loss tan δ = 5 × 10-4 at a frequency of 1 Hz. Nanoparticulate ZnCr2O4-based thin films with a thickness varying from 0.5 to 2 μm were fabricated by the drop-casting method and subsequently incorporated into planar capacitors whose dielectric performance was characterized. This study undoubtedly shows that the dielectric properties of nanostructured zinc chromite powders can be engineered by the rational control of their morphology upon the variation of the post-synthesis heat treatment process.

Oxygen Vacancy Promoted O2 Activation over Mesoporous Ni-Co Mixed Oxides for Aromatic Hydrocarbon Oxidation

Whether the oxygen vacancies of heterogeneous catalysts improve their catalytic activity or not has recently been the topic of intense debate in the oxidation of hydrocarbons. We designed an effective strategy to construct mesoporous Ni-Co mixed oxides via a ligand-assisted self-assembly approach. The surface oxygen vacancy concentrations of the mesoporous Ni-Co mixed oxide catalysts were regulated by changing the doping amount of Ni or the reduction method, and the relationship between oxygen vacancies and catalytic activity was studied. Controlled experiments and DFT calculations revealed that oxygen molecules were more favorably adsorbed and activated on oxygen vacancies to form active oxygen species. Increasing the oxygen vacancy concentration within a certain range can effectively enrich the active oxygen species, therefore improving the oxidation rate of ethylbenzene. The optimized mCo₃O₄-0.1NiO catalyst exhibited a remarkable catalytic activity for the solvent-free oxidation of ethylbenzene to acetophenone, typically including 68.0% conversion and 95.4% selectivity (20 mg mCo₃O₄-0.1NiO, 10 mL ethylbenzene, and 0.6 MPa O₂).

Property and Reactivity Relationships of Co3O4 with Diverse Nanostructures for Soot Oxidation

Cobalt oxide (Co₃O₄) nanostructures with different morphologies (nanocubes, nanoplates, and nanoflowers) were synthesized by a simple hydrothermal method and used for catalytic oxidation of soot particles. Through the study of the physicochemical properties of the catalysts, the key factors affecting the performance of soot oxidation were investigated. The results showed that all three kinds of Co₃O₄ nanocrystals exhibited excellent low-temperature activity in catalytic oxidation of soot, and the Co₃O₄ nanoflowers showed higher oxidation activity of soot compared with Co₃O₄ nanocubes and Co₃O₄ nanoplates, whose T _m was only 370 °C. The excellent activity of Co₃O₄ nanoflowers was due to the large amount of Co³⁺ and lattice oxygen on their surface and highly defective structure, which promoted the adsorption and activation of oxygen species. The large crystallite size and few surface defects were the main reasons for the poor catalytic performance of Co₃O₄ nanocubes. During soot oxidation, the crystallite size of the catalysts and the contact between the catalysts and soot played a significant role in the catalytic performance.

Insights into the Redox and Structural Properties of CoOx and MnOx: Fundamental Factors Affecting the Catalytic Performance in the Oxidation Process of VOCs

Volatile organic compound (VOC) abatement has become imperative nowadays due to their harmful effect on human health and on the environment. Catalytic oxidation has appeared as an innovative and promising approach, as the pollutants can be totally oxidized at moderate operating temperatures under 500 °C. The most active single oxides in the total oxidation of hydrocarbons have been shown to be manganese and cobalt oxides. The main factors affecting the catalytic performances of several metal-oxide catalysts, including CoOx and MnOx, in relation to the total oxidation of hydrocarbons have been reviewed. The influence of these factors is directly related to the Mars–van Krevelen mechanism, which is known to be applied in the case of the oxidation of VOCs in general and hydrocarbons in particular, using transitional metal oxides as catalysts. The catalytic behaviors of the studied oxides could be closely related to their redox properties, their nonstoichiometric, defective structure, and their lattice oxygen mobility. The control of the structural and textural properties of the studied metal oxides, such as specific surface area and specific morphology, plays an important role in catalytic applications. A fundamental challenge in the development of efficient and low-cost catalysts is to choose the criteria for selecting them. Therefore, this research could be useful for tailoring advanced and high-performance catalysts for the total oxidation of VOCs.

Chemical conversion based on the crystal facet effect of transition metal oxides and construction methods for sharp-faced nanocrystals

In-depth research has found that the nanocrystal facet of transition metal oxides (TMOs) greatly affects their heterogeneous catalytic performance, as well as the property of photocatalysis, gas sensing, electrochemical reaction, etc. that are all involved in chemical conversion processes. Therefore, the facet-dependent properties of TMO nanocrystals have been fully and carefully studied by combining systematic experiments and theoretical calculations, and mechanisms of chemical reactions are accurately explained at the molecular level, which will be closer to the essence of reactions. Evidently, as an accurate investigation on crystal facets, well-defined TMO nanocrystals are the basis and premise for obtaining relevant credible results, and shape-controlled synthesis of TMO nanocrystals thereby has received great attention and development. The success in understanding of facet-dependent properties and shape-controlled synthesis of TMO nanocrystals is highly valuable for the control of reaction and the design of high-efficiency TMO nanocrystal catalysts as well as other functional materials in practical applications.

Green Synthesis of Iron-Doped Cobalt Oxide Nanoparticles from Palm Kernel Oil via Co-Precipitation and Structural Characterization

In this study, a bio-derived precipitating agent/ligand, palm kernel oil, has been used as an alternative route for the green synthesis of nanoparticles of Fe-doped Co3O4 via the co-precipitation reaction. The palm oil was extracted from dried palm kernel seeds by crushing, squeezing and filtration. The reaction of the palm kernel oil with potassium hydroxide, under reflux, yielded a solution containing a mixture of potassium carboxylate and excess hydroxide ions, irrespective of the length of saponification. The as-obtained solution reacts with an aqueous solution containing iron and cobalt ions to yield the desired metallo-organic precursor, iron cobalt carboxylate. Characterization of the precursors by IR and gas chromatography (GC) attests to the presence of carboxylate fatty acids in good agreement with the proportion contained in the oil, and ICP confirms that the metallic ratios are in the proportion used during the synthesis. Analysis of the products thermally decomposed between 400 °C and 600 °C by XRD, EDX, TEM and ToF-SIMS, established that cobalt iron oxide nanoparticles (Co(1-x)Fex)3O4 were obtained for x ≤ 0.2 and a nanocomposite material (Co(1-x)Fex)3O4/Fe3O4 for x ≥ 0.2, with sizes between 22 and 9 nm. ToF-SIMS and XRD provided direct evidence of the progressive substitution of cobalt by iron in the Co3O4 crystal structure for x ≤ 0.2.

Chemisorbed Superoxide Species Enhanced the High Catalytic Performance of Ag/Co3O4 Nanocubes for Soot Oxidation

The respective action mode between surface-adsorbed oxygen and bulk lattice oxygen during catalytic soot oxidation is still not fully recognized. Herein, a series of Ag-loaded Co₃O₄ catalysts with different Ag loading amounts were prepared by the impregnation method, and 5% Ag/Co₃O₄ presented competitive catalytic activity toward soot combustion with a T₅₀ below 290 °C in 10% O₂/N₂. This remarkable improvement in catalytic performance could be primarily attributed to the enhanced Ag-Co₃O₄ metal-support interaction induced by the formation of uniform, dispersive, and suitable size metallic Ag nanoparticles. The activation, activity, consumption-regeneration, identification, and reaction of surface-adsorbed oxygen along with the activity of bulk lattice oxygen were characterized by various designed and in situ techniques. The results demonstrated that the chemisorbed superoxide species (O₂^-) play the potentially responsible role for boosting soot combustion, while the bulk lattice oxygen is much less active within the tested temperatures, inducing a negligible activity contribution. Moreover, soot-temperature programmed reduction, isothermal kinetic study, and density functional theory calculation provided supplementary support for the enhancement effect of Ag-Co₃O₄ combination in the activation and utilization of surface-adsorbed oxygen. The overall objective of this work is to identify the role of surface-adsorbed oxygen and bulk lattice oxygen for soot oxidation over Ag/Co₃O₄ catalysts.

Interstitial boron-doped mesoporous semiconductor oxides for ultratransparent energy storage

Realizing transparent and energy-dense supercapacitor is highly challenging, as there is a trade-off between energy storing capability and transparency in the active material film. We report here that interstitial boron-doped mesoporous semiconductor oxide shows exceptional electrochemical capacitance which rivals other pseudocapacitive materials, while maintaining its transparent characteristic. This improvement is credited to the robust redox reactions at interstitial boron-associated defects that transform inert semiconductor oxides into an electrochemically active material without affecting its transparency. By precisely tuning the level of doping, the pseudocapacitive reactivity of these materials is optimized, resulting in a volumetric capacitance up to 1172 F cm-3. Attributing to such efficient charge storage utilization on the active film, the fabricated transparent supercapacitor delivers a maximum areal energy density of 1.36 × 10-3 mWh cm-2 that is close to those of conventional pseudocapacitive materials, with nearly 100% capacitance retention after 15000 cycles and ultrahigh transparency (up to 85% transmittance at 550 nm). In addition, this device shows excellent durability and flexibility with multiple optional outputs, demonstrating the potential as a transparent energy supply in planar electronics.

Study on the Photocatalysis Mechanism of the Z-Scheme Cobalt Oxide Nanocubes/Carbon Nitride Nanosheets Heterojunction Photocatalyst with High Photocatalytic Performances

An efficient Z-scheme Co₃O₄/g-C₃N₄ heterojunction photocatalyst was developed via in-situ forming Co₃O₄ nanocubes on the g-C₃N₄ nanosheet in the hydrothermal process. The obtained photocatalyst exhibited high photocatalytic activity for the visible-light-driven catalytic reduction of Cr(VI) and catalytic oxidation of tetracycline (TC). Among the as-synthesized catalysts, Co₃O₄/g-C₃N₄-0.04 (the mass ratio of g-C₃N₄ to Co₃O₄ is 0.04) sample exhibits the most efficient catalytic activities. The photocatalytic reduction and photocatalytic oxidation efficiencies of Co₃O₄/g-C₃N₄-0.04 can obtain 81.3 and 92.6 %, respectively. Moreover, the TC is mineralized in the course of photocatalytic degradation, 72.2% of TOC is removed from the reaction system. In addition, the apparent quantum efficiency for the removal of Cr(VI) was also obtained and the the Co₃O₄/g-C₃N₄-0.04 could achieve the highest apparent quantum efficiency among the samples. The enhancing photocatalytic activities originated from the efficient interfacial charge migration and separation obtained in Co₃O₄/g-C₃N₄-0.04, which is preliminarily confirmed by the photoluminescence spectra, time-resolved photoluminescence spectra and the photoelectrochemical characterizations. Finally, we speculate that the Co₃O₄/g-C₃N₄ heterostructures follow a more reasonable Z-scheme charge transfer in this study, which is confirmed by analyzing the results of electron paramagnetic resonance, radical scavenging experiments, and theoretical calculations.

Facet-Dependent Cobalt Ion Distribution on the Co3O4 Nanocatalyst Surface

Co₃O₄ is an important catalyst widely used for CO oxidation or electrochemical water oxidation near room temperature and was also recently used as support for single-atom catalysts (SACs). Co₃O₄ with a spinel structure hosts dual oxidation states of Co²⁺ and Co³⁺ in the lattice, leading to the complexity of its surface structure as the exposure of Co²⁺ and Co³⁺ has a significant impact on the performance of the catalysts. Although it is acknowledged that different facets exhibit varied catalytic activities and different abilities in hosting single atoms to provide active centers in SACs, the Co₃O₄ surface structure remains under-investigated. In this study, major facets of {111}, {110}, and {100} were studied down to subangstrom scale using advanced electron microscopy. We noticed that each facet has its own most stable surface configuration. The distribution of Co²⁺ and Co³⁺ on each facet was quantified, revealing a facet-dependent distribution of Co²⁺ and Co³⁺. Co³⁺ was found to be preferentially exposed on {100} and {110} as well as surface steps. Surface reconstruction was revealed, where a subangstrom scale shift of Co²⁺ was confirmed on facets of {111} and {100} due to polarity compensation and oxygen deficiency on the surface. This work not only improves our fundamental understanding of the Co₃O₄ surface structure but also may promote the design of Co₃O₄-based catalysts with tunable activity and stability.

Facet effect of Co3O4 nanocatalysts on the catalytic decomposition of ammonium perchlorate

Crystal facets can affect the catalytic decomposition of ammonium perchlorate, but the underlying mechanisms have long remained unclear. Here, we use the nanorods, nanosheets and nanocubes of Co₃O₄ catalysts exposing {110}, {111} and {100} facets as model systems to investigate facet effects on catalytic AP decomposition. The peak temperature of high temperature decomposition (HTD) process (T_HTD) of AP by nanorods, nanosheets and nanocubes Co₃O₄ decrease from 437.0 °C to 289.4 °C, 299.9 °C and 326.3 °C, respectively, showing obvious facet effects. We design experiments about AP decomposition under different atmospheres to investigate its mechanism and verify that the accumulation of ammonia (NH₃) on AP surface can inhibit its decomposition and that the facet effects are related to the adsorption and oxidation of NH₃. The binding energies of NH₃ on the {110}, {111} and {100} planes calculated via density functional theory (DFT) are -1.774 eV, -1.638 eV, and -1.354 eV, respectively, indicating that the {110} planes are more favorable for the adsorption of NH₃. Moreover, the {110} planes are readily to form CoNO structure, which benefits the further oxidation of the NH₃.

Nanometal Oxides with Special Surface Physicochemical Properties to Promote Electrochemical Detection of Heavy Metal Ions

Heavy metal ions (HMIs) are one of the major environmental pollution problems currently faced. To monitor and control HMIs, rapid and reliable detection is required. Electrochemical analysis is one of the promising methods for on-site detection and monitoring due to high sensitivity, short response time, etc. Recently, nanometal oxides with special surface physicochemical properties have been widely used as electrode modifiers to enhance sensitivity and selectivity for HMIs detection. In this work, recent advances in the electrochemical detection of HMIs using nanometal oxides, which are attributed to specific crystal facets and phases, surficial defects and vacancies, and oxidation state cycle, are comprehensively summarized and discussed in aspects of synthesis, characterization, electroanalysis application, and mechanism. Moreover, the challenges and opportunities for the development and application of nanometal oxides with functional surface physicochemical properties in electrochemical determination of HMIs are presented.

Hydroxyl groups attached to Co2+ on the surface of Co3O4: a promising structure for propane catalytic oxidation

Co₃O₄ catalysts with three specific morphologies (nanocubes, nanosheets, and nanooctahedra) were prepared using simple preparation methods and tested for catalytic combustion of propane under the same reaction conditions.

Optimization of the facet structure of cobalt oxide catalysts for enhanced hydrogen evolution reaction

The three different exposed crystal planes of Co₃O₄ catalysts, in which the {112} and {011} planes with abundant Co³⁺ sites exhibited photocatalytic hydrogen evolution activity superior to that of the {001} plane.

Three-dimensional porous Co3O4-CoO@GO composite combined with N-doped carbon for superior lithium storage

Transition metal oxides (TMOs) as anode materials have potential for lithium-ion batteries (LIBs). However, the poor rate capacity and cycle stability restrict its application. Herein, we demonstrate a facile one-step hydrothermal method to construct a three-dimensional porous conductive network structure, which consists of thin-layered graphene, ultrafine Co₃O₄-CoO nanoparticles and nitrogen-doped carbon. This unique structure can effectively prevent particle agglomeration and cracking caused by volume expansion, provide fast passage for lithium ion/electron transport during cycling and improve the electrical conductivity of the electrode. Moreover, the electrochemical kinetic analysis proves that this is a process dominated by pseudocapacitive behavior. Consequently, the N-C@Co₃O₄-CoO@GO hybrid electrode delivers an ultrahigh capacity of 1 273.1 mA h g^-1 at 0.1 A g^-1 and superior rate performance (725.1 mA h g^-1 at 5 A g^-1). Additionally, it exhibits a high reversible cycling capacity of 787.4 mA h g^-1 at 1 A g^-1 over 600 cycles and even maintains excellent cycling stability for a ultra-long cycles at 5 A g^-1. This work provides a feasible strategy for fabricating the N-C@Co₃O₄-CoO@GO composite as a promising high-performance TMOs anode for LIBs.

Superbending (0-180°) and High-Voltage Operating Metal-Oxide-Based Flexible Supercapacitor

Among various energy storage devices, flexible supercapacitors having high mechanical stability with extreme bending and foldable features are highly attractive for a large number of emerging portable lightweight consumer devices. Here, we report the fabrication of such a superflexible supercapacitor by using novel octahedron-shaped NiCo₂O₄ nanoparticles as the electrode material for the first time. A new, low-cost hydrothermal method was used to synthesize 50-60 nm monodispersed perfect octahedron nanoparticles without any structural deformation. An all-solid-state symmetric flexible supercapacitor was fabricated by sandwiching the octahedron nanoparticles and [EMIM][BF₄] ionic liquid electrolyte between two sheets of newly developed superflexible current collector substrate. The calculated specific capacity and specific capacitance values are found to be 97.9 mAh g^-1 and 117.3 F g^-1, respectively, at 0.625 A g^-1 current density and 3.0 V applied potential. It also offered a high energy density value of 33.54 Wh kg^-1 and 10 000 measured cycling stability. The supercapacitor is so flexible that it can be bent or fold up to 180° without any mechanical deformation, and the measured capacitance and energy and power densities remain almost constant at any angle of twisting. For instance, calculated values of capacitances obtained by bending the cell at angles of 180, 150, 135, 90, and 45° are found to be 62, 63.3, 63.73, 64, and 66 F g^-1 respectively, in comparison to 67 F g^-1 for a nonbending or flat (0°) cell. A faster ion switching between electrode/electrolyte interface, [EMIM][BF₄] electrolyte, and octahedron shape of the nanoparticle electrode material is found to be responsible for the outstanding charge storage behavior.

β-SnWO4 with Morphology-Controlled Synthesis and Facet-Depending Photocatalysis

Faceted β-SnWO₄ microcrystals are prepared with different morphologies including tetrahedra, truncated tetrahedra, truncated octahedra, and short-spiked and long-spiked spikecubes. All of these morphologies are prepared with comparable experimental conditions via microwave-assisted synthesis of high-boiling alcohols (the so-called polyol method). The decisive parameters for controlled formation of one or the other morphology of faceted β-SnWO₄ microcrystals are studied and discussed, including microwave-assisted heating, Sn(OH)₂ as the Sn²⁺ reservoir, the temperature of particle nucleation, the temperature of particle growth, and the concentration of the starting materials. Morphology and crystallinity are characterized by scanning electron microscopy, X-ray powder diffraction, UV-vis, and Fourier-transform infrared spectroscopy. Finally, the photocatalytic properties of all obtained faceted microcrystals-tetrahedra, truncated tetrahedra, truncated octahedra, cubes, and short-spiked and long-spiked spikecubes-are exemplarily compared with regard to the photocatalytic decomposition of rhodamine B and the influence of the respective surface crystal planes.

Synergetic Effect of Facet Junction and Specific Facet Activation of ZnFe2O4 Nanoparticles on Photocatalytic Activity Improvement

Crystal facet engineering has been proved as a versatile approach in modulating the photocatalytic activity of semiconductors. However, the facet-dependent properties and underlying mechanisms of spinel ZnFe₂O₄ in photocatalysis still have rarely been explored. Herein, ZnFe₂O₄ nanoparticles with different {001} and {111} facets exposed were successfully synthesized via a facile hydrothermal method. Facet-dependent photocatalytic degradation performance toward gaseous toluene under visible light irradiation was observed, where truncated octahedral ZnFe₂O₄ (ZFO(T)) nanoparticles with both {001} and {111} facets exposed exhibited a superior performance than the others. The formed surface facet junction between {010} and {100} facets was responsible for the improved activity by separating photogenerated e^-/h⁺ pairs efficiently to reduce their recombination rate. Photogenerated electrons and holes were demonstrated to be immigrated onto {001} and {111} facets, separately. Intriguingly, electron paramagnetic resonance trapping results indicated that both ^•O₂^- and ^•OH were abundantly present in the ZFO(T) sample under visible light irradiation as major reactive oxygen species involved in the photocatalytic degradation process. Additionally, further investigation revealed that {001} facets played a predominant role in activating photogenerated transient species H₂O₂ into ^•OH, beneficially boosting the intrinsic photocatalytic activity. This work has not only presented a promising strategy in regulating photocatalytic performance through the synergetic effect of facet junction and specific facet activation but also broadened the application of facet engineering with multiple effects simultaneously cooperating.

Intercalation of Layered Materials from Bulk to 2D

Intercalation in few-layer (2D) materials is a rapidly growing area of research to develop next-generation energy-storage and optoelectronic devices, including batteries, sensors, transistors, and electrically tunable displays. Identifying fundamental differences between intercalation in bulk and 2D materials will play a key role in developing functional devices. Herein, advances in few-layer intercalation are addressed in the historical context of bulk intercalation. First, synthesis methods and structural properties are discussed, emphasizing electrochemical techniques, the mechanism of intercalation, and the formation of a solid-electrolyte interphase. To address fundamental differences between bulk and 2D materials, scaling relationships describe how intercalation kinetics, structure, and electronic and optical properties depend on material thickness and lateral dimension. Here, diffusion rates, pseudocapacity, limits of staging, and electronic structure are compared for bulk and 2D materials. Next, the optoelectronic properties are summarized, focusing on charge transfer, conductivity, and electronic structure. For energy devices, opportunities also emerge to design van der Waals heterostructures with high capacities and excellent cycling performance. Initial studies of heterostructured electrodes are compared to state-of-the-art battery materials. Finally, challenges and opportunities are presented for 2D materials in energy and optoelectronic applications, along with promising research directions in synthesis and characterization to engineer 2D materials for superior devices.

Evolution of Co3O4 Nanocubes through Stepwise Oriented Attachment

Uniformly sized building units are generally required to construct highly elaborate architectures over a wide range. Defined nanocubes of Co₃O₄ evolved from deformed precursor nanograins 2-5 nm in diameter through direct oriented attachment in a nonpolar medium. Uniformly sized primary nanocubes ∼8 nm on a side with {100} faces were formed by adjusting the coverage of the oxide nanograins with oleic acid. Larger nanocubes 20-40 nm on a side were produced with further direct oriented attachment of the primary nanocubes. Ordered arrays, such as superlattices, were found to be constructed by the indirect oriented attachment of the primary and larger nanocubes covered with organic molecules.

Cu-Doped Porous Carbon Derived from Heavy Metal-Contaminated Sewage Sludge for High-Performance Supercapacitor Electrode Materials

In this paper, we report a complete solution for enhanced sludge treatment involving the removal of toxic metal (Cu(II)) from waste waters, subsequent pyrolytic conversion of these sludge to Cu-doped porous carbon, and their application in energy storage systems. The morphology, composition, and pore structure of the resultant Cu-doped porous carbon could be readily modulated by varying the flocculation capacity of Cu(II). The results demonstrated that it exhibited outstanding performance for supercapacitor electrode applications. The Cu(II) removal efficiency has been evaluated and compared to the possible energy benefits. The flocculant dosage up to 200 mg·L⁻¹ was an equilibrium point existing between environmental impact and energy, at which more than 99% Cu(II) removal efficiency was achieved, while the resulting annealed product showed a high specific capacity (389.9·F·g⁻¹ at 1·A·g⁻¹) and good cycling stability (4% loss after 2500 cycles) as an electrode material for supercapacitors.

Insights into the Morphological Effect of Co3O4 Crystallite on Catalytic Oxidation of Vinyl Chloride

Co3O4 catalysts of cube and sphere shapes were prepared by one-step hydrothermal synthesis with different controlled amounts of Co(NO3)2·6H2O and NaOH. The morphological effects on both physicochemical properties and catalytic activities of vinyl chloride oxidation were investigated by material characterization and performance evaluation. The obtained results showed that the morphology, resulting in the exposure difference of crystal planes, significantly affected the catalytic property. The catalytic activity for vinyl chloride oxidation followed a descending order of Co3O4 cube (Co3O4-c) > Co3O4 sphere (Co3O4-s) > Co3O4 commercial (Co3O4-com). The cube-shaped Co3O4 presented higher catalytic activity and stability than Co3O4 spheres despite their similar crystallographic structures as well as physicochemical and redox properties. Accordingly, the different catalytic behaviors should be attributed to a morphological effect. The Co3O4 cube with a preferential exposure of (001) plane presented higher abundance of surface Co2+ cations and adsorbed oxygen species, which acted as the active sites responsible for the improvement of its catalytic activity.

A Universal Strategy for Constructing Seamless Graphdiyne on Metal Oxides to Stabilize the Electrochemical Structure and Interface

The structural and interfacial stabilities of metal oxides (MOs) are key issues while facing the volumetric variation and intensive interfacial polarization in electrochemical applications, including lithium-ion batteries (LIBs), supercapacitors, and catalysts. The growth of a seamless all-carbon interfacial layer on MOs with complex dimensions is not only a scientific problem, but also a practical challenge in these fields. Here, the growth of graphdiyne under ultramild condition is successfully implemented in situ for coating MOs of complex dimensions. The seamless all-carbon interface and conductive network are formed at the same time. This method cleverly avoids the structural degradation of MOs at a high temperature in the presence of traditional carbon materials. Under the protection of the high-quality graphdiyne layer, the samples as LIB anodes deliver high performances in terms of Coulomb efficiency, capacity, long-term retention, and structural and interfacial stabilities. Both experimental achievements and theoretical calculations demonstrate that the graphdiyne is a particular protection layer for MOs and plays a crucial role for preventing the structural and interfacial degradation of the electrode. Furthermore, the universality of this method will promote the potential applications of many promising MOs in other electrochemical fields.

Size-dependent kinetics during non-equilibrium lithiation of nano-sized zinc ferrite

Spinel transition metal oxides (TMOs) have emerged as promising anode materials for lithium-ion batteries. It has been shown that reducing their particle size to nanoscale dimensions benefits overall electrochemical performance. Here, we use in situ transmission electron microscopy to probe the lithiation behavior of spinel ZnFe₂O₄ as a function of particle size. We have found that ZnFe₂O₄ undergoes an intercalation-to-conversion reaction sequence, with the initial intercalation process being size dependent. Larger ZnFe₂O₄ particles (40 nm) follow a two-phase intercalation reaction. In contrast, a solid-solution transformation dominates the early stages of discharge when the particle size is about 6–9 nm. Using a thermodynamic analysis, we find that the size-dependent kinetics originate from the interfacial energy between the two phases. Furthermore, the conversion reaction in both large and small particles favors {111} planes and follows a core-shell reaction mode. These results elucidate the intrinsic mechanism that permits fast reaction kinetics in smaller nanoparticles.

Reducing particle size of electrode materials to nanoscale dimensions is believed responsible for their enhanced reaction kinetics and electrochemical performance. Here, the authors use in situ transmission electron microscopy to study the dynamic process of the spinel zinc ferrite nanoparticles as a function of size, finding that the intercalation reaction pathway changes below a critical particle size.

Ultrafine ternary metal oxide particles with carbon nanotubes: a metal–organic-framework-based approach and superior lithium-storage performance

A metal–organic-framework template approach was used to fabricate ultrafine ternary metal oxide nanoparticles embedded in CNTs, which exhibit larger-than-theoretical reversible capacities for lithium-ion batteries.

Aqueous Dual-Ion Battery Based on a Hematite Anode with Exposed {1 0 4} Facets

The aqueous rechargeable lithium battery (ARLB) is one of the most promising devices for large-scale grid applications. Currently, a key issue for ARLBs is to develop promising anode materials with favorable electrochemical performances. Here, for the first time, we demonstrate an aqueous battery that utilizes the reversible redox reaction with hydroxide ions (OH^- ) in the hematite (Fe₂ O₃ ) anode and a commercial Li ion intercalation compound in neutral solution as the cathode. The fabricated aqueous battery displays a reversible capacity of 92 mAh g^-1 . The morphology of the used Fe₂ O₃ anode with exposed {1 0 4} facets for this aqueous battery is unique and attractive. Importantly, with the dual-pH neutral-alkaline hybrid electrolyte, many excellent anode materials that previously could only work in alkaline electrolytes can now be successfully combined with commercial cathodes in neutral solutions, which may significantly enrich the range of anode materials for ARLBs. In addition, the reported battery configuration can be extended to other aqueous batteries beyond Li-ion ones with lower cost.

The electrochemical properties of Co3O4 as a lithium-ion battery electrode: a first-principles study

Extensive first principles calculations were performed to study the structural and electrochemical features of Co3O4 during its lithiation process as an anode material for lithium-ion batteries (LIBs). We found that with up to 8 mol Li in Co3O4, the formed LinCo3O4 structures are stable for low Li concentrations of n ≤ 1, but obvious structure distortions and volume expansions occur for LinCo3O4 with n > 1. This may be the reason why Co3O4 has a high Li capability but low cycling life as a LIB anode. The ab initio molecular dynamics simulations for LinCo3O4 (n = 2, 4, 8) further suggest a two-step electrochemistry process of Co3O4 → CoO → Co upon the lithiation process. We detected a distorted surface structure as Li atoms react with the Co3O4(110) surface, which also reduces the rate capability of the Co3O4 anode.

Visualizing Facet-Dependent Hydrogenation Dynamics in Individual Palladium Nanoparticles

Surface faceting in nanoparticles can profoundly impact the rate and selectivity of chemical transformations. However, the precise role of surface termination can be challenging to elucidate because many measurements are performed on ensembles of particles and do not have sufficient spatial resolution to observe reactions at the single and subparticle level. Here, we investigate solute intercalation in individual palladium hydride nanoparticles with distinct surface terminations. Using a combination of diffraction, electron energy loss spectroscopy, and dark-field contrast in an environmental transmission electron microscope (TEM), we compare the thermodynamics and directly visualize the kinetics of 40-70 nm {100}-terminated cubes and {111}-terminated octahedra with approximately 2 nm spatial resolution. Despite their distinct surface terminations, both particle morphologies nucleate the new phase at the tips of the particle. However, whereas the hydrogenated phase-front must rotate from [111] to [100] to propagate in cubes, the phase-front can propagate along the [100], [11̅0], and [111] directions in octahedra. Once the phase-front is established, the interface propagates linearly with time and is rate-limited by surface-to-subsurface diffusion and/or the atomic rearrangements needed to accommodate lattice strain. Following nucleation, both particle morphologies take approximately the same time to reach equilibrium, hydrogenating at similar pressures and without equilibrium phase coexistence. Our results highlight the importance of low-coordination number sites and strain, more so than surface faceting, in governing solute-driven reactions.