Low-temperature NH3 abatement via selective oxidation over a supported copper catalyst with high Cu+ abundance

Selective catalytic NH3-to-N2 oxidation (NH3-SCO) is highly promising for abating NH3 emissions slipped from stationary flue gas after-treatment devices. Its practical application, however, is limited by the non-availability of low-cost catalysts with high activity and N2 selectivity. Here, using defect-rich nitrogen-doped carbon nanotubes (NCNT-AW) as the support, we developed a highly active and durable copper-based NH3-SCO catalyst with a high abundance of cuprous (Cu+) sites. The obtained Cu/NCNT-AW catalyst demonstrated outstanding activity with a T50 (i.e. the temperature to reach 50% NH3 conversion) of 174°C in the NH3-SCO reaction, which outperformed not only the Cu catalyst supported on N-free O-functionalized CNTs (OCNTs) or NCNT with less surface defects, but also those most active Cu catalysts in open literature. Reaction kinetics measurements and temperature-programmed surface reactions using NH3 as a probe molecule revealed that the NH3-SCO reaction on Cu/NCNT-AW follows an internal selective catalytic reaction (i-SCR) route involving nitric oxide (NO) as a key intermediate. According to mechanistic investigations by X-ray photoelectron spectroscopy, Raman spectroscopy, and X-ray absorption spectroscopy, the superior NH3-SCO performance of Cu/NCNT-AW originated from a synergy of surface defects and N-dopants. Specifically, surface defects promoted the anchoring of CuO nanoparticles on N-containing sites and, thereby, enabled efficient electron transfer from N to CuO, increasing significantly the fraction of SCR-active Cu+ sites in the catalyst. This study puts forward a new idea for manipulating and utilizing the interplay of defects and N-dopants on carbon surfaces to fabricate Cu+-rich Cu catalysts for efficient abatement of slip NH3 emissions via selective oxidation.

Derivatives of Br-doped metal-organic framework for improved acetaldehyde adsorption-photocatalytic oxidation

Different Br-doped metal-organic frameworks (MOFs) derived (Brx@UiO-66) have been prepared by heat treatment using UiO-66 as the precursor. The experimental results showed that Br0.2@UiO-66 exhibited the best photocatalytic oxidation and adsorption performances toward acetaldehyde. In the dynamic system, the acetaldehyde removal rate and adsorption capacity of Br0.2@UiO-66 were 93.25 % and 230.59 mg/g, respectively. The improvement of the photocatalytic performance can be attributed to the presence of Br ions and CBr bonds, which facilitated the rapid separation of electrons and holes and the production of •O2-. In addition, Br0.2@UiO-66 had a better adsorption performance than 300UiO-66, mainly because of the increased Lewis acidity of the metal active sites due to Br doping. Radical capture experiments indicated that •O2- and e- were the primary active substances in acetaldehyde oxidation, and allowed establishing the possible mechanism of acetaldehyde oxidation. This work shows that MOFs can have high catalytic oxidation performances toward volatile organic compounds (VOCs) while retaining their adsorption capacity, and can be used for practical applications in the adsorption-catalytic integrated degradation of VOCs.

One-pot synthesis of N-doped petroleum coke-based microporous carbon for high-performance CO2 adsorption and supercapacitors

Waste resource utilization of petroleum coke is crucial for achieving global carbon emission reduction. Herein, a series of N-doped microporous carbons were fabricated from petroleum coke using a one-pot synthesis method. The as-prepared samples had a large specific surface area (up to 2512 m2/g), a moderate-high N content (up to 4.82 at.%), and high population (55%) of ultra-micropores (<0.7 nm). Regulating the N content and ultra-microporosity led to efficient CO2 adsorption and separation. At ambient pressure, the optimal N-doped petroleum coke-based microporous carbon exhibited the highest CO2 uptake of 4.25 mmol/g at 25°C and 6.57 mmol/g at 0°C. These values are comparable or even better than those of numerous previously reported adsorbents prepared by multistep synthesis, primarily due to the existence of ultra-micropores. The sample exhibited excellent CO2/N2 selectivity at 25°C owing to the abundant basic pyridinic and pyrrolic N species; and showed superior CO2 adsorption-desorption cycling performance, which was maintained at 97% after 10 cycles at 25°C. Moreover, petroleum coke-based microporous carbon, with a considerably high specific surface area and hierarchical pore structure, exhibited excellent electrochemical performance over the N-doped sample, maintaining a favorable specific capacitance of 233.25 F/g at 0.5 A/g in 6 mol/L KOH aqueous electrolyte. This study provides insight into the influence of N-doping on the porous properties of petroleum coke-based carbon. Furthermore, the as-prepared carbons were found to be promising adsorbents for CO2 adsorption, CO2/N2 separation and electrochemical application.

Identification of NOx emissions and source characteristics by TROPOMI observations - A case study in north-central Henan, China

With the development of industries, air pollution in north-central Henan is becoming increasingly severe. The TROPOspheric Monitoring Instrument (TROPOMI) provides nitrogen dioxide (NO2) column densities with high spatial resolution. Based on TROPOMI, in this study, the nitrogen oxides (NOx) emissions in north-central Henan are derived and the emission hotspots are identified with the flux divergence method (FDM) from May to September 2021. The results indicate that Zhengzhou has the highest NOx emissions in north-central Henan. The most prominent hotspots are in Guancheng Huizu District (Zhengzhou) and Yindu District (Anyang), with emissions of 448.4 g/s and 300.3 g/s, respectively. The Gaussian Mixture Model (GMM) is applied to quantify the characteristics of emission hotspots, including the diameter, eccentricity, and tilt angle, among which the tilt angle provides a novel metric for identifying the spatial distribution of pollution sources. Furthermore, the results are compared with the CAMS global anthropogenic emissions (CAMS-GLOB-ANT) and Multi-resolution Emission Inventory model for Climate and air pollution research (MEIC), and they are generally in good agreement. However, some point sources, such as power plants, may be missed by both inventories. It is also found that for emission hotspots near transportation hubs, CAMS-GLOB-ANT may not have fully considered the actual traffic flow, leading to an underestimation of transportation emissions. These findings provide key information for the accurate implementation of pollution prevention and control measures, as well as references for future optimization of emission inventories. Consequently, deriving NOx emissions from space, quantifying the characteristics of emission hotspots, and combining them with bottom-up inventories can provide valuable insights for targeted emission control.

Investigation of catalytic methane oxidation over Ag/Co2MOx (M = Co, Ni, Cu) catalysts with varying interfacial electron transfer

Atom-doped Co3O4 catalysts loaded with Ag were examined as cost-effective catalysts for methane oxidation. The synthesized Ag/Co2NiOx catalysts exhibited distinctive surface characteristics in contrast with Ag/Co3O4 and Ag/Co2CuOx catalysts prepared using a similar method. Characterization results unveiled that Ag/Co2NiOx featured a higher presence of active surface oxygen species, lattice defects, a larger surface area, and enhanced reducibility. A methane oxidation catalytic performance followed the sequence: Ag/Co2NiOx > Ag/Co3O4 > Ag/Co2CuOx. The investigation delved into methane degradation pathways on the surfaces of three catalysts, examining their behavior under both aerobic and anaerobic atmospheres through in-situ DRIFTS analysis. Furthermore, introducing Ag showed a marked positive effect on Co-Ni mixed oxide, inducing electron transfer and a more active electron system, whereas it exhibited an inverse impact within the surface of Co-Cu mixed oxide. This work provides innovative perspectives on the development of forthcoming environmental catalysts.

Enhancement Effect Induced by the Second Metal to Promote Ozone Catalytic Oxidation of VOCs

It is a promising research direction to develop catalysts with high stability and ozone utilization for low-temperature ozone catalytic oxidation of VOCs. While bimetallic catalysts exhibit excellent catalytic activity compared with conventional single noble metal catalysts, limited success has been achieved in the influence of the bimetallic effect on the stability and ozone utilization of metal catalysts. Herein, it is necessary to systematically study the enhancement effect in the ozone catalytic reaction induced by the second metal. With a simple continuous impregnation method, a platinum-cerium bimetallic catalyst is prepared. Also highlighted are studies from several aspects of the contribution of the second metal (Ce) to the stability and ozone utilization of the catalysts, including the "electronic effect" and "geometric effect". The synergistic removal rate of toluene and ozone is nearly 100% at 30 °C, and it still shows positive stability after high humidity and a long reaction time. More importantly, the instructive significance, which is the in-depth knowledge of enhanced catalytic mechanism of bimetallic catalysts resulting from a second metal, is provided by this work.

Cobalt catalyzed ethane dehydrogenation to ethylene with CO2: Relationships between cobalt species and reaction pathways

TiO2, ZrO2 and a series of TiO2-ZrO2 (TxZ1, x means the atomic ratio of Ti/Zr = 10, 5, 1, 0.2 and 0.1) composite oxide supports were prepared through co-precipitation, and then 3 wt% Co was loaded through wetness impregnation methods. The obtained 3 wt% Co/TiO2 (3CT), 3 wt% Co/ZrO2 (3CZ) and 3 wt% Co/TxZ1 (3CTxZ1) catalysts were evaluated for the oxidative ethane dehydrogenation reaction with CO2 (CO2-ODHE) as a soft oxidant. 3CT1Z1 catalyst exhibits excellent catalytic properties, with C2H4 yield, C2H6 conversion and CO2 conversion about 24.5 %, 33.8 % and 18.0 % at 650 °C, respectively. X-Ray Diffraction (XRD), in-situ Raman, UV-vis diffuse reflectance spectra (UV-vis DRS), H2 temperature-programmed reduction (H2-TPR), Electron paramagnetic resonance (EPR) and quasi in-situ X-ray Photoelectron Spectroscopy (XPS) have been utilized to thoroughly characterize the investigated catalysts. The results revealed that 3CT1Z1 produced TiZrO4 solid solution with more metal defect sites and oxygen vacancies (Ov), promoting the formation of Co2+-TiZrO4 structure. Furthermore, the presence of Ov and Ti3+can facilitate the high dispersion and stabilization of Co2+, as well as suppressing the severe reduction of Co2+, leading to superior ethane oxidative dehydrogenation activity. Besides, less Co0 is beneficial to ODHE reaction, because of its promotion effects for reverse water gas shift reaction; however, more Co0 results in dry reforming reaction (DRE). This work will shed new lights for the design and preparation of highly efficient catalysts for ethylene production.

Process-specified emission factors and characteristics of VOCs from the auto-repair painting industry

Daily use of passenger vehicles leads to considerable emission of volatile organic compounds (VOCs), which are key precursors to the ground-level ozone pollution. While evaporative and tailpipe emission of VOCs from the passenger vehicles can be eliminated largely, or even completely, by electrification, VOCs emission from the use of coatings in auto-repair is unavoidable and has long been ignored. Here, we present for the first time, to the best of our knowledge, a comprehensive investigation on the emission factors and process-specified characteristics of VOCs from auto-repair painting, based on field measurements over 15 representative auto-repair workshops in the Pearl-River-Delta area, China. Replacement of solvent-borne coatings with water-borne counterparts, which was only achieved partially in the Basecoat step but not in the Putty, Primer and Clearcoat steps, could reduce the per automobile VOCs emission from 756.5 to 489.6 g and the per automobile ozone formation potential (OFP) from 2776.5 to 1666.4 g. Implementation of exhaust after-treatment led to a further reduction of the per automobile VOCs emission to 340.9 g, which is still ca. 42% higher than that from the state-of-art painting processes for the manufacture of passenger vehicles. According to the analysis of VOCs compositions, the Putty process was dominated by the emission of styrene, while Primer, Basecoat (solvent-borne) and Clearcoat steps were all characterized by the emission of n-butyl acetate and xylenes. By contrast, water-borne Basecoat step showed a prominent emission of n-amyl alcohol. Notably, for the full painting process to repair an automobile, n-butyl acetate emerged as the most abundant species in the VOCs emission, whereas xylenes contributed most significantly to the OFP. Scenario analysis suggested that reducing VOCs contents in the coatings, as well as improving the after-treatment efficiency, were highly potential solutions for effective reduction of VOCs emission from auto-repair. Our study contributes to an update of industrial inventories of VOCs emission, and may provide valuable insights for reducing VOCs emission and OFPs from the auto-repair industry.

Efficient Photothermal Catalytic Oxidation Enabled by Three-Dimensional Nanochannel Substrates

Photothermal catalysis exhibits promising prospects to overcome the shortcomings of high-energy consumption of traditional thermal catalysis and the low efficiency of photocatalysis. However, there is still a challenge to develop catalysts with outstanding light absorption capability and photothermal conversion efficiency for the degradation of atmospheric pollutants. Herein, we introduced the Co3O4 layer and Pt nanoclusters into the three-dimensional (3D) porous membrane through the atomic layer deposition (ALD) technique, leading to a Pt/Co3O4/AAO monolithic catalyst. The 3D ordered nanochannel structure can significantly enhance the solar absorption capacity through the light-trapping effect. Therefore, the embedded Pt/Co3O4 catalyst can be rapidly heated and the O2 adsorbed on the Pt clusters can be activated to generate sufficient O2- species, exhibiting outstanding activity for the diverse VOCs (toluene, acetone, and formaldehyde) degradation. Optical characterization and simulation calculation confirmed that Pt/Co3O4/AAO exhibited state-of-the-art light absorption and a notable localized surface plasmon resonance (LSPR) effect. In situ diffuse reflectance infrared Fourier transform spectrometry (in situ DRIFTS) studies demonstrated that light irradiation can accelerate the conversion of intermediates during toluene and acetone oxidation, thereby inhibiting byproduct accumulation. Our finding extends the application of AAO's optical properties in photothermal catalytic degradation of air pollutants.

Historical emission and reduction of VOCs from the petroleum refining industry and their potential for secondary pollution formation in Guangdong, China

China became the world leader in crude oil processing capacity in 2021. However, petroleum refining generates significant volatile organic compound (VOC) emissions, and the composite source profile, source-specific emission factors, and emission inventories of VOCs in the petroleum refining industry remain poorly understood. In this study, we focused on Guangdong, China's major province for crude oil processing, and systematically evaluated the historical emissions and reduction of VOCs in the petroleum refining industry from 2001 to 2020. We accomplished this by establishing local source-specific emission factors and composite source profiles. Finally, we quantitatively assessed the potential impact of these emissions on ozone and secondary organic aerosol formation. Our results revealed that VOC emissions from the petroleum refining industry in Guangdong followed an increasing-then-decreasing trend from 2001 to 2020, peaking at 37.3 Gg in 2016 and declining to 18.7 Gg in 2020. Storage tanks and wastewater collection and treatment remained the two largest sources, accounting for 41.9 %-53.4 % and 20.6 %-27.5 % of total emissions, respectively. Initially, Guangzhou and Maoming made the most significant contributions, with Huizhou becoming a notable contributor after 2008. Emission reduction efforts for VOCs in Guangdong's petroleum refining industry began showing results in 2017, with an average annual VOC emission reduction of 21.5 Gg from 2017 to 2020 compared to the unabated scenario. Storage tanks, wastewater collection and treatment, and loading operations were the primary sources of emission reduction, with significant contributions from Maoming, Huizhou, and Guangzhou. Alkanes made the largest contribution to VOC emissions, while alkenes/alkynes and aromatics comprised the most significant portions of ozone formation potential (OFP) and secondary organic aerosol formation potential (SOAP). We also estimated VOC emissions and reduction from petroleum refining for China from 2001 to 2020, and measures such as "one enterprise, one policy" and deep control strategies could reduce emissions by at least 103.9 Gg.

Non-Interacting Ni and Fe Dual-Atom Pair Sites in N-Doped Carbon Catalysts for Efficient Concentrating Solar-Driven Photothermal CO2 Reduction

Solar-to-chemical energy conversion under weak solar irradiation is generally difficult to meet the heat demand of CO2 reduction. Herein, a new concentrated solar-driven photothermal system coupling a dual-metal single-atom catalyst (DSAC) with adjacent Ni-N4 and Fe-N4 pair sites is designed for boosting gas-solid CO2 reduction with H2 O under simulated solar irradiation, even under ambient sunlight. As expected, the (Ni, Fe)-N-C DSAC exhibits a superior photothermal catalytic performance for CO2 reduction to CO (86.16 μmol g-1  h-1 ), CH4 (135.35 μmol g-1  h-1 ) and CH3 OH (59.81 μmol g-1  h-1 ), which are equivalent to 1.70-fold, 1.27-fold and 1.23-fold higher than those of the Fe-N-C catalyst, respectively. Based on theoretical simulations, the Fermi level and d-band center of Fe atom is efficiently regulated in non-interacting Ni and Fe dual-atom pair sites with electronic interaction through electron orbital hybridization on (Ni, Fe)-N-C DSAC. Crucially, the distance between adjacent Ni and Fe atoms of the Ni-N-N-Fe configuration means that the additional Ni atom as a new active site contributes to the main *COOH and *HCO3 dissociation to optimize the corresponding energy barriers in the reaction process, leading to specific dual reaction pathways (COOH and HCO3 pathways) for solar-driven photothermal CO2 reduction to initial CO production.

Copper Site Motion Promotes Catalytic NOx Reduction under Zeolite Confinement

Ammonia-mediated selective catalytic reduction (NH3-SCR) is currently the key approach to abate nitrogen oxides (NOx) emitted from heavy-duty lean-burn vehicles. The state-of-art NH3-SCR catalysts, namely, copper ion-exchanged chabazite (Cu-CHA) zeolites, perform rather poorly at low temperatures (below 200 °C) and are thus incapable of eliminating effectively NOx emissions under cold-start conditions. Here, we demonstrate a significant promotion of low-temperature NOx reduction by reinforcing the dynamic motion of zeolite-confined Cu sites during NH3-SCR. Combining complex impedance-based in situ spectroscopy (IS) and extended density-functional tight-binding molecular dynamics simulation, we revealed an environment- and temperature-dependent nature of the dynamic Cu motion within the zeolite lattice. Further coupling in situ IS with infrared spectroscopy allows us to unravel the critical role of monovalent Cu in the overall Cu mobility at a molecular level. Based on these mechanistic understandings, we elicit a boost of NOx reduction below 200 °C by reinforcing the dynamic Cu motion in various Cu-zeolites (Cu-CHA, Cu-ZSM-5, Cu-Beta, etc.) via facile postsynthesis treatments, either in a reductive mixture at low temperatures (below 250 °C) or in a nonoxidative atmosphere at high temperatures (above 450 °C).

Tuning the Hierarchical Pore Structure and the Metal Site in a Metal-Organic Framework Derivative to Unravel the Mechanism for the Adsorption of Different Volatile Organic Compounds

Volatile organic compounds (VOCs) are one of the main classes of air pollutants, and it is important to develop efficient adsorbents to remove them from the atmosphere. To do this most efficiently, we need to understand the mechanism of VOC adsorption. In this work, we described how the metal organic framework (MOF), ZIF-8, was used as a precursor to generate MOF derivatives (Zn-GC) through temperature-controlled calcination, which had adjustable metal sites and hierarchical pore structure. It was used as a model adsorbent to study the adsorption and desorption characteristics of different VOCs. Zn-GC-850 with developed pores exhibited higher adsorption performance for the benzene series, whereas Zn-GC-650 with more metal sites had a better adsorption capacity for oxygen-containing VOCs. By tuning the molecular structure of the VOCs, we revealed the adsorption mechanism of different VOCs at the molecular level. The more developed hierarchical pore structure obtained at the higher temperature facilitates the diffusion of the benzene series, and the noncovalent interaction between their methyl group(s) and the carbonized MOF derivatives improves the adsorption affinity; while the higher exposure of Zn sites obtained at lower temperature favors the adsorption of oxygen-containing VOCs by Zn-O bonds. The mass transfers of VOCs and the role of the adsorbent were simulated by multiple theoretical models. This study strengthens the basis for the design and optimization of the adsorbent and catalyst for VOCs treatment.

Neratinib + fulvestrant + trastuzumab for HR-positive, HER2-negative, HER2-mutant metastatic breast cancer: outcomes and biomarker analysis from the SUMMIT trial

BACKGROUND

HER2 mutations are targetable alterations in patients with hormone receptor-positive (HR+) metastatic breast cancer (MBC). In the SUMMIT basket study, patients with HER2-mutant MBC received neratinib monotherapy, neratinib + fulvestrant, or neratinib + fulvestrant + trastuzumab (N + F + T). We report results from 71 patients with HR+, HER2-mutant MBC, including 21 (seven in each arm) from a randomized substudy of fulvestrant versus fulvestrant + trastuzumab (F + T) versus N + F + T.

PATIENTS AND METHODS

Patients with HR+ HER2-negative MBC with activating HER2 mutation(s) and prior cyclin-dependent kinase 4/6 inhibitor (CDK4/6i) therapy received N + F + T (oral neratinib 240 mg/day with loperamide prophylaxis, intramuscular fulvestrant 500 mg on days 1, 15, and 29 of cycle 1 then q4w, intravenous trastuzumab 8 mg/kg then 6 mg/kg q3w) or F + T or fulvestrant alone. Those whose disease progressed on F + T or fulvestrant could cross-over to N + F + T. Efficacy endpoints included investigator-assessed objective response rate (ORR), clinical benefit rate (RECIST v1.1), duration of response, and progression-free survival (PFS). Plasma and/or formalin-fixed paraffin-embedded tissue samples were collected at baseline; plasma was collected during and at end of treatment. Extracted DNA was analyzed by next-generation sequencing.

RESULTS

ORR for 57 N + F + T-treated patients was 39% [95% confidence interval (CI) 26% to 52%); median PFS was 8.3 months (95% CI 6.0-15.1 months). No responses occurred in fulvestrant- or F + T-treated patients; responses in patients crossing over to N + F + T supported the requirement for neratinib in the triplet. Responses were observed in patients with ductal and lobular histology, 1 or ≥1 HER2 mutations, and co-occurring HER3 mutations. Longitudinal circulating tumor DNA sequencing revealed acquisition of additional HER2 alterations, and mutations in genes including PIK3CA, enabling further precision targeting and possible re-response.

CONCLUSIONS

The benefit of N + F + T for HR+ HER2-mutant MBC after progression on CDK4/6is is clinically meaningful and, based on this study, N + F + T has been included in the National Comprehensive Cancer Network treatment guidelines. SUMMIT has improved our understanding of the translational implications of targeting HER2 mutations with neratinib-based therapy.

Revealing the Formation and Reactivity of Cage-Confined Cu Pairs in Catalytic NOx Reduction over Cu-SSZ-13 Zeolites by In Situ UV-Vis Spectroscopy and Time-Dependent DFT Calculation

The low-temperature mechanism of chabazite-type small-pore Cu-SSZ-13 zeolite, a state-of-the-art catalyst for ammonia-assisted selective reduction (NH3-SCR) of toxic NOx pollutants from heavy-duty vehicles, remains a debate and needs to be clarified for further improvement of NH3-SCR performance. In this study, we established experimental protocols to follow the dynamic redox cycling (i.e., CuII ↔ CuI) of Cu sites in Cu-SSZ-13 during low-temperature NH3-SCR catalysis by in situ ultraviolet-visible spectroscopy and in situ infrared spectroscopy. Further integrating the in situ spectroscopic observations with time-dependent density functional theory calculations allows us to identify two cage-confined transient states, namely, the O2-bridged Cu dimers (i.e., μ-η2:η2-peroxodiamino dicopper) and the proximately paired, chemically nonbonded CuI(NH3)2 sites, and to confirm the CuI(NH3)2 pair as a precursor to the O2-bridged Cu dimer. Comparative transient experiments reveal a particularly high reactivity of the CuI(NH3)2 pairs for NO-to-N2 reduction at low temperatures. Our study demonstrates direct experimental evidence for the transient formation and high reactivity of proximately paired CuI sites under zeolite confinement and provides new insights into the monomeric-to-dimeric Cu transformation for completing the Cu redox cycle in low-temperature NH3-SCR catalysis over Cu-SSZ-13.

Scalable Fabrication of Superhydrophobic Coating with Rough Coral Reef-Like Structures for Efficient Self-Cleaning and Oil-Water Separation: An Experimental and Molecular Dynamics Simulation Study

Superhydrophobic coating has a great application prospect in self-cleaning and oil-water separation but remains challenging for large-scale preparation of robust and weather-resistant superhydrophobic coatings via facile approaches. Herein, this work reports a scalable fabrication of weather-resistant superhydrophobic coating with multiscale rough coral reef-like structures by spraying the suspension containing superhydrophobic silica nanoparticles and industrial coating varnish on various substrates. The coral reef-like structures effectively improves the surface roughness and abrasion resistance. Rapid aging experiments (3000 h) and the outdoor building project application (3000 m2 ) show that the sprayed superhydrophobic coating exhibits excellent self-cleaning properties, weather resistance, and environmental adaptability. Moreover, the combined silica-coating varnish-polyurethane (CSCP) superhydrophobic sponge exhibits exceptional oil-water separation capabilities, selectively absorbing the oils from water up to 39 times of its own weight. Furthermore, the molecular dynamics (MD) simulation reveals that the combined effect of higher surface roughness, smaller diffusion coefficient of water molecules, and weaker electrostatic interactions between water and the surface jointly determines the superhydrophobicity of the prepared coating. This work deepens the understanding of the anti-wetting mechanism of superhydrophobic surfaces from the perspective of energetic and kinetic properties, thereby paving the way for the rational design of superhydrophobic materials and their large-scale applications.

Unlocking High-Efficiency Methane Oxidation with Bimetallic Pd-Ce Catalysts under Zeolite Confinement

Catalytic complete oxidation is an efficient approach to reducing methane emissions, a significant contributor to global warming. This approach requires active catalysts that are highly resistant to sintering and water vapor. In this work, we demonstrate that Pd nanoparticles confined within silicalite-1 zeolites (Pd@S-1), fabricated using a facile in situ encapsulation strategy, are highly active and stable in catalyzing methane oxidation and are superior to those supported on the S-1 surface due to a confinement effect. The activity of the confined Pd catalysts was further improved by co-confining a suitable amount of Ce within the S-1 zeolite (PdCe_0.4@S-1), which is attributed to confinement-reinforced Pd-Ce interactions that promote the formation of oxygen vacancies and highly reactive oxygen species. Furthermore, the introduction of Ce improves the hydrophobicity of the S-1 zeolite and, by forming Pd-Ce mixed oxides, inhibits the transformation of the active PdO phase to inactive Pd(OH)₂ species. Overall, the bimetallic PdCe_0.4@S-1 catalyst delivers exceptional outstanding activity and durability in complete methane oxidation, even in the presence of water vapor. This study may provide new prospects for the rational design of high-performance and durable Pd catalysts for complete methane oxidation.

Surface adsorbed and lattice oxygen activated by the CeO2/Co3O4 interface for enhancive catalytic soot combustion: Experimental and theoretical investigations

Metal oxide-oxide interface on supported catalyst has been rarely studied due to the complex interfacial structure and synthetic challenge. Herein, different Ag-supported CeO₂/Co₃O₄ samples with various covered-state of CeO₂ were prepared for catalytic soot oxidation. In comparison, catalytic activity was significantly improved by grafting CeO₂ on Co₃O₄, in which the best performing Ag/CoCe-2 exhibited remarkable catalytic performance towards soot oxidation with a T₅₀ of 290.5 ℃ under 10 % O₂/N₂. Catalyst characterization investigated by Scanning Electron Microscope (SEM), quasi in-situ X-ray Photoelectron Spectroscopy (XPS), in-situ Raman, etc. revealed that this outstanding promotion in catalytic activity can be principally ascribed to the formation of the CeO₂/Co₃O₄ interface. An appropriate CeO₂ dosage maximized the contact and interaction between Co₃O₄ and CeO₂, resulting in the largest CeO₂/Co₃O₄ interface featured with abundant generated superoxide species and activated surface lattice oxygen. Density functional theory (DFT) calculations were also carried out for the oxygen vacancy formation energy, Gibbs free energy, etc. In presence of the CeO₂/Co₃O₄ interface, a charge density redistribution around the adsorbed reactants at oxygen vacancies could be formed, owing to the efficient charge transfer enhanced by the electron-appealing effect. The change in electronic structure favored reducing the oxygen vacancy formation energy and boosting the lattice oxygen activation induced by the hybridized Co-O-Ce bonds, finally lowering the adsorption and activation barriers for reactive species and accelerating the reaction kinetics.

Strain-Engineering of Mesoporous Cs3 Bi2 Br9 /BiVO4 S-Scheme Heterojunction for Efficient CO2 Photoreduction

Slow charge kinetics and unfavorable CO₂ adsorption/activation strongly inhibit CO₂ photoreduction. In this study, a strain-engineered Cs₃ Bi₂ Br₉ /hierarchically porous BiVO₄ (s-CBB/HP-BVO) heterojunction with improved charge separation and tailored CO₂ adsorption/activation capability is developed. Density functional theory calculations suggest that the presence of tensile strain in Cs₃ Bi₂ Br₉ can significantly downshift the p-band center of the active Bi atoms, which enhances the adsorption/activation of inert CO₂ . Meanwhile, in situ irradiation X-ray photoelectron spectroscopy and electron spin resonance confirm that efficient charge transfer occurs in s-CBB/HP-BVO following an S-scheme with built-in electric field acceleration. Therefore, the well-designed s-CBB/HP-BVO heterojunction exhibits a boosted photocatalytic activity, with a total electron consumption rate of 70.63 µmol g^-1 h^-1 , and 79.66% selectivity of CO production. Additionally, in situ diffuse reflectance infrared Fourier transform spectroscopy reveals that CO₂ photoreduction undergoes a formaldehyde-mediated reaction process. This work provides insight into strain engineering to improve the photocatalytic performance of halide perovskite.

Research on the diurnal variation characteristics of ozone formation sensitivity and the impact of ozone pollution control measures in "2 + 26" cities of Henan Province in summer

Near-surface ozone pollution is becoming an increasingly serious air quality issue in China, especially in "2 + 26" cities (Beijing-Tianjin-Hebei and nearby cities). HN2 + 26 cities ("2 + 26" cities of Henan Province) are located in the south of "2 + 26" cities, with frequent and severe ozone pollution events in recent years. This study studied the diurnal evolution characteristics of ozone formation sensitivity (OFS) of HN2 + 26 cities from May to September in 2021 by the innovative combination of Global Ozone Monitoring Experiment (GOME-2B) and Ozone Monitoring Instrument (OMI) satellite data, and assessed the impact of ozone pollution control measures (OPCMs) implemented from June 26 to July 1, 2021. The localized FNR (ratio of formaldehyde to nitrogen dioxide of satellite measurement) threshold (1.4-2.55) was established, and it was found that OFS in May-September 2021 was mainly in VOCs-limited regime in the morning (~10:00), while transitional/NO_x-limited regime in the afternoon (~14:00). Three periods (before, during and after the OPCMs) were divided to evaluate the impact of OPCMs on OFS. It was indicated that OPCMs had no impact on the morning OFS, but had a significant impact on the afternoon OFS. Specifically, the OFS in two industrial cities Xinxiang (XX) and Zhengzhou (ZZ) shifted from transitional regime to NO_x-limited regime after the OPCMs. We further investigated OFS differences between urban and suburban areas and found that OFS shift of XX only existed in urban areas, while that of ZZ existed in both urban and suburban areas. We compared their measures and found that it is effective to take hierarchical control measures on different levels of ozone pollution days to alleviate ozone pollution. This study provides an improved understanding of diurnal evolution characteristics of OFS and the impacts of OPCMs on it, which will provide a theoretical basis for formulating more scientific ozone pollution control policies.

Constructing Highly Active Metal Oxides for Toluene Degradation by Fenton Iron Mud Modulation

Fenton iron mud (IM) is a hazardous solid waste produced by Fenton oxidation technology after treating industrial wastewater. Thus, it is necessary and challenging to develop a recycling technology to back-convert dangerous materials into useful products. Herein, we develop a sustainable approach to prepare highly active metal oxides via a solid-state grinding method. IM, as an amorphous material, can disperse and interact well with these supported metal oxides, boosting toluene degradation significantly. Among these IM-based catalysts, the catalyst 8% MnO_x/IM-0.2VC exhibits the best performance (T₁₀₀ = 290 °C), originating from the oxide-support interaction and optimal balance between low-temperature reducibility and oxygen vacancy concentration. In addition, in situ diffuse reflectance infrared Fourier transform spectrometry (DRIFTS) results expound that ring breakage is prone to occur on MnO_x, and oxygen vacancies are beneficial to adsorb oxygen and activate oxygen species to boost toluene oxidation following the Mars-van Krevelen mechanism. This work advances a complete industrial hazardous waste recycling route to develop extremely active catalysts.

Research on the ozone formation sensitivity indicator of four urban agglomerations of China using Ozone Monitoring Instrument (OMI) satellite data and ground-based measurements

Near surface ozone is a typical secondary pollutant, and is mostly generated by a series of complex photochemical reactions of volatile organic compounds (VOCs) and nitrogen oxides (NO_x) in the air under sunlight. At present, a large number of studies have applied FNR (a ratio of formaldehyde (HCHO) to nitrogen dioxide (NO₂) retrieved by satellite) indicator to study the ozone formation sensitivity (OFS). OFS analysis is critical for taking targeted ozone pollution prevention and control measures. Regional OFS can be more accurately diagnosed by utilizing localized FNR threshold. In this study, localized FNR thresholds were established for four severe ozone polluted urban agglomerations in China (Beijing-Tianjin-Hebei (BTH) region, Yangtze River Delta (YRD) region, Pearl River Delta (PRD) region, and Chengdu-Chongqing (CY) region), based on the statistical analysis between FNR (obtained from OMI observation, with daily transit time of approximately 13:45 local standard time) and ΔO₃/ΔNO₂ (the ratio of ozone change to nitrogen dioxide change between two consecutive months, obtained from ground measurements) from 2014 to 2016. And these thresholds were verified by the statistical analysis between FNR and ΔO₃/O₃ (ozone change rate between two consecutive months), and between FNR and O₃ concentration during the OFS significant shift months. Furthermore, the results were also compared and verified with the method proposed by previous studies. The results indicate that there are significant regional dependences in the FNR threshold, and the lower-upper limits for the four urban agglomerations are as follows: 0.65-1.21 for BTH, 0.64-1.48 for the YRD, 1.25-2.39 for the PRD, and 1.44-3.69 for CY (FNR < lower limit indicates VOCs-limited regime; lower limit < FNR < upper limit indicates transitional regime; FNR > upper limit indicates NO_x-limited regime). This method eliminates the problems associated with the undifferentiated use of FNR thresholds in different regions and significantly reduces the deviations for OFS.

Unraveling the role of Co3O4 facet for photothermal catalytic oxidation of methanol via operando spectroscopy and theoretical investigation

Tubular, pie- and bread-shaped forms of Co₃O₄ with exposed {110}, {112} and {111} facets were prepared and compared in their photothermal catalytic performance and reaction pathways during the oxidation of methanol. Among them, the Co₃O₄ with exposed {110} facet exhibited the best photothermal catalytic performance (95% methanol conversion, 93% CO₂ yield) under solar irradiation, while also maintaining good stability and moisture resistance. Reaction mechanism studies showed that the {110} facets had a strong adsorption capacity for formaldehyde, which facilitated its conversion to formate. The transformation of formaldehyde to formate species was the key step. The key step on the {110} facet was conversion of formaldehyde to a mono-dentate formate species, while conversion on the {112} and {111} facets was mainly to bi-dentate formate species. This study demonstrated that the design of preferential exposed crystal facet can regulate the pathway of photothermal catalytic reaction and realize efficient solar energy utilization.

Quenching-Induced Defect-Rich Platinum/Metal Oxide Catalysts Promote Catalytic Oxidation

Enhancing oxygen activation through defect engineering is an effective strategy for boosting catalytic oxidation performance. Herein, we demonstrate that quenching is an effective strategy for preparing defect-rich Pt/metal oxide catalysts with superior catalytic oxidation activity. As a proof of concept, quenching of α-Fe₂O₃ in aqueous Pt(NO₃)₂ solution yielded a catalyst containing Pt single atoms and clusters over defect-rich α-Fe₂O₃ (Pt/Fe₂O₃-Q), which possessed state-of-the-art activity for toluene oxidation. Structural and spectroscopic analyses established that the quenching process created abundant lattice defects and lattice dislocations in the α-Fe₂O₃ support, and stronger electronic interactions between Pt species and Fe₂O₃ promote the generation of higher oxidation Pt species to modulate the adsorption/desorption behavior of reactants. In situ diffuse reflectance infrared Fourier transform spectroscopy (in situ DRIFTS) characterization studies and density functional theory (DFT) calculations determined that molecular oxygen and Fe₂O₃ lattice oxygen were both activated on the Pt/Fe₂O₃-Q catalyst. Pt/CoMn₂O₄, Pt/MnO₂, and Pt/LaFeO₃ catalysts synthesized by the quenching method also offered superior catalytic activity for toluene oxidation. Results encourage the wider use of quenching for the preparation of highly active oxidation catalysts.

Causal relationship between Type 1 diabetes and osteoporosis and fracture occurrence: a two-sample Mendelian randomization analysis

We used two-sample Mendelian Randomization to reveal causal estimates of type 1 diabetes and bone. Type 1 diabetes was found to be a risk factor for bone metabolic health, although there was no clear evidence to support a genetic association between type 1 diabetes and osteoporosis and fracture risk.

INTRODUCTION

Based on the random assignment of gametes at conception, Mendelian randomization (MR) analysis simulates randomized controlled trials in an observational setting. Therefore, we used MR to assess the association causality of type 1 diabetes (T1D) with fractures and osteoporosis.

METHODS

From a genome-wide association meta-analysis, independent single nucleotide polymorphisms closely associated with T1D were selected as instrumental variables. Data on fracture and osteoporosis were obtained from the FinnGen Consortium. We performed a two-sample MR analysis, using inverse-variance weighted (IVW) as the primary analysis method, to assess possible causal associations between T1D and bone risk. The results were verified by MR-Egger regression and median weighted method (WME). MR-PRESSO and MR-Egger intercepts were used to evaluate the horizontal pleiotropy of instrumental variables, and the Q-test and "leave-one-out" methods were used to test the heterogeneity of MR results.

RESULTS

IVW (OR=1.040, 95% CI=0.974-1.109, P=0.238), MR-Egger regression (OR=1.077, 95% CI=0.921-1.260, P=0.372) and WME (OR=1.021, 95% CI=0.935-1.114, P=0.643) all showed that there was no causal relationship between T1D and osteoporosis, but the direction was consistent. The indicative significance of IVW results in T1D and forearm fractures (OR=1.062, 95% CI=1.010-1.117, P=0.020), but the results are not robust enough. There was no causal effect in femur, lumbar and pelvis, or shoulder and upper arm fractures.

CONCLUSIONS

After MR analysis, although T1D may be a risk factor for bone health, we do not have sufficient evidence to support a causal effect of T1D on osteoporosis and fractures at a genetically predicted level. More cases need to be included for analysis.

Precise preparation of biomass-based porous carbon with pore structure-dependent VOCs adsorption/desorption performance by bacterial pretreatment and its forming process

Pore distribution characteristic is one of the most crucial factors for porous adsorption materials, and the variety of volatile organic compounds (VOCs) approaches about how to simply and accurately tailor practical porous carbons for VOCs adsorption has gradually attracted attention. Here, precursors with different lignocellulose mass ratios have been used to produce porous carbon for model experiments to investigate the influence of the precursor lignocellulose contents on the pore structure and distribution characteristics of porous carbon, and the applicability of these mechanisms to real biomass materials has been further verified through bacteria-targeted bagasse decomposition: the microvolumes of ultra-micropores have decreased with decrease in cellulose contents, while mesopores have followed the reverse trend. The dynamic toluene adsorption/desorption performances of the obtained samples have been tested. The BACs-36 exhibits high toluene adsorption performance in low concentration with 635 mg/g while the BACs-48 shows excellent reusability in 10 times cycles. Based on this the balance between the adsorptive and regenerative capacities has been observed which indicates that carbon materials with abundant micropores and narrow mesopores have much better adsorption performance than porous carbon with a hierarchical pore structure, while the latter show better regeneration abilities than the former, which resulting in less desorption as a counter-acting force at the pore wall. Furthermore, the porous carbon has been shaped by one-step co-pyrolysis method using phenolic resin, which can not only maintain the hardness but also can avoid pore plugging phenomenon.

Improved emission factors and speciation to characterize VOC emissions in the printing industry in China

Printing industry is one of the most important sources of industrial volatile organic compound (VOC) emissions in China, and is thus a key industrial sector in terms of VOC control. However, process-based VOC emission and speciation from the printing industry have not been well identified, mainly owing to the poor emission factors (EFs) and diversity of source profiles. In this study, we systematically characterized process-based VOC emissions from the printing industry for the period of 2010-2019, through the establishment of improved emission factors and composite source profiles. VOC emissions from the printing industry were found to continuously increase from 2010 to 2018, reaching their maximum in 2018 at 939.8 Gg, but started to decrease afterwards. The substantial growth is driven by the large demand for ink and adhesive and the absence of effective control measures in the printing industry. The total VOC emissions and ozone formation potential (OFP) in China in 2019 were 916.1 Gg and 1834.5 Gg, respectively. Gravure printing and the compound process were the processes that contributed the most to both emissions and OFP. Rapidly developing provinces such as Guangdong, Jiangsu, and Zhejiang were the largest contributors to emissions. Oxygenated VOCs (OVOCs) accounted for most of the VOC emissions, followed by alkanes and aromatics, while aromatics were the dominant groups for total OFP, followed by alkenes/alkynes and OVOCs. Ethyl acetate, toluene, isopropanol, isopentane, and n-pentane were the top five VOC species in terms of emissions, while toluene, ethyl acetate, 1,3-butadiene, isopentane, and 1-butene were the top five species in terms of OFP. Scientific and precise control policy were proposed, involving four aspects: environmental access, emission standards, classification and management, and research on source substitution. We believe our study will provide an important reference for the systematic characterization and control policy of VOC emissions from other industries.

Insights into the Role of Nanorod-Shaped MnO2 and CeO2 in a Plasma Catalysis System for Methanol Oxidation

Published papers highlight the roles of the catalysts in plasma catalysis systems, and it is essential to provide deep insight into the mechanism of the reaction. In this work, a coaxial dielectric barrier discharge (DBD) reactor packed with γ-MnO₂ and CeO₂ with similar nanorod morphologies and particle sizes was used for methanol oxidation at atmospheric pressure and room temperature. The experimental results showed that both γ-MnO₂ and CeO₂ exhibited good performance in methanol conversion (up to 100%), but the CO₂ selectivity of CeO₂ (up to 59.3%) was much higher than that of γ-MnO₂ (up to 28.6%). Catalyst characterization results indicated that CeO₂ contained more surface-active oxygen species, adsorbed more methanol and utilized more plasma-induced active species than γ-MnO₂. In addition, in situ Raman spectroscopy and Fourier transform infrared spectroscopy (FT-IR) were applied with a novel in situ cell to reveal the major factors affecting the catalytic performance in methanol oxidation. More reactive oxygen species (O₂^2-, O^2-) from ozone decomposition were produced on CeO₂ compared with γ-MnO₂, and less of the intermediate product formate accumulated on the CeO₂. The combined results showed that CeO₂ was a more effective catalyst than γ-MnO₂ for methanol oxidation in the plasma catalysis system.

Cold-Start NOx Mitigation by Passive Adsorption Using Pd-Exchanged Zeolites: From Material Design to Mechanism Understanding and System Integration

It remains a major challenge to abate efficiently the harmful nitrogen oxides (NO_x) in low-temperature diesel exhausts emitted during the cold-start period of engine operation. Passive NO_x adsorbers (PNA), which could temporarily capture NO_x at low temperatures (below 200 °C) and release the stored NO_x at higher temperatures (normally 250-450 °C) to downstream selective catalytic reduction unit for complete abatement, hold promise to mitigate cold-start NO_x emissions. In this review, recent advances in material design, mechanism understanding, and system integration are summarized for PNA based on palladium-exchanged zeolites. First, we discuss the choices of parent zeolite, Pd precursor, and synthetic method for the synthesis of Pd-zeolites with atomic Pd dispersions, and review the effect of hydrothermal aging on the properties and PNA performance of Pd-zeolites. Then, we show how different experimental and theoretical methodologies can be integrated to gain mechanistic insights into the nature of Pd active sites, the NO_x storage/release chemistry, as well as the interactions between Pd and typical components/poisons in engine exhausts. This review also gathers several novel designs of PNA integration into modern exhaust after-treatment systems for practical application. At the end, we discuss the major challenges, as well as important implications, for the further development and real application of Pd-zeolite-based PNA in cold-start NO_x mitigation.

Economical and Sustainable Synthesis of Small-Pore Chabazite Catalysts for NOx Abatement by Recycling Organic Structure-Directing Agents

The application of small-pore chabazite-type SSZ-13 zeolites, key materials for the reduction of nitrogen oxides (NO_x) in automotive exhausts and the selective conversion of methane, is limited by the use of expensive N,N,N-trimethyl-1-ammonium adamantine hydroxide (TMAdaOH) as an organic structure-directing agent (OSDA) during hydrothermal synthesis. Here, we report an economical and sustainable route for SSZ-13 synthesis by recycling and reusing the OSDA-containing waste liquids. The TMAdaOH concentration in waste liquids, determined by a bromocresol green colorimetric method, was found to be a key factor for SSZ-13 crystallization. The SSZ-13 zeolite synthesized under optimized conditions demonstrates similar physicochemical properties (surface area, porosity, crystallinity, Si/Al ratio, etc.) as that of the conventional synthetic approach. We then used the waste liquid-derived SSZ-13 as the parent zeolite to synthesize Cu ion-exchanged SSZ-13 (i.e., Cu-SSZ-13) for ammonia-mediated selective catalytic reduction of NO_x (NH₃-SCR) and observed a higher activity as well as better hydrothermal stability than Cu-SSZ-13 by conventional synthesis. In situ infrared and ultraviolet-visible spectroscopy investigations revealed that the superior NH₃-SCR performance of waste liquid-derived Cu-SSZ-13 results from a higher density of Cu²⁺ sites coordinated to paired Al centers on the zeolite framework. The technoeconomic analysis highlights that recycling OSDA-containing waste liquids could reduce the raw material cost of SSZ-13 synthesis by 49.4% (mainly because of the higher utilization efficiency of TMAdaOH) and, meanwhile, the discharging of wastewater by 45.7%.

Unravelling the correlation of dielectric barrier discharge power and performance of Pt/CeO2 catalysts for toluene oxidation

Two “volcano” peaks in the relevant activity curve showcased that plasma discharge power had a significant impact on the activity of Pt/CeO2-Px catalysts and modulating discharge power could be regarded as an efficient method to optimize catalyst performance.

Carbonyls from commercial, canteen and residential cooking activities as crucial components of VOC emissions in China

Cooking in China supply the large population with nutrition and, as a commercial activity, it also promotes the economic growth of Chinese society. The specific cooking styles in China can produce complex volatile organic compound (VOC) emissions. The resulting adverse effects on the environment and human health of carbonyls from cooking should not be ignored. We quantitatively evaluated the contribution of carbonyls to common VOCs (carbonyl/VOC ratio) from cooking activities in China through the establishment and comparison of the source profiles, emission factors (EFs), emission amount and ozone formation potential (OFP). It was found that carbonyls are crucial components of VOCs from commercial, canteen and residential cooking activities (COC, CAC and REC, respectively). The carbonyl/VOC ratio from cooking activities in China had EFs, emissions, and a total OFP of 22-65 %, 23-34 %, and 49-104 %, respectively. The high OFP was due to the high OFP emissions intensity (OFP_EI) and maximum incremental reactivity (MIR) values of carbonyls. This indicates that to alleviate O₃ pollution, OFP-based control measures that target carbonyls might be more efficient than measures that target common VOCs. Priority should be given to emission controlling COC emissions, specifically those from medium- and large-scale catering. Formaldehyde, acetaldehyde, and hexanal were the key carbonyl species that form O₃ in the environment. Our findings imply that cooking-emitted carbonyls should not be overlooked in investigations of O₃ formation and that these compounds should be subject to strict regulations.

Characteristics and sources of volatile organic compounds (VOCs) in Xinxiang, China, during the 2021 summer ozone pollution control

Real-time monitoring of volatile organic compounds (VOCs) was conducted in Xinxiang, China, during the implementation of Xinxiang's ozone pollution control period (CP) in June 2021. To evaluate the effectiveness of the control measures, three study periods were determined by combining meteorological conditions and the implementation time of the control measures: before, during, and after the CP of ozone pollution (BCP, CP, and ACP, respectively). The average concentrations of VOCs during the three periods were 41.20 ± 4.99 ppbv, 33.64 ± 5.65 ppbv, and 37.42 ± 2.59 ppbv, respectively, with the same top three components, namely oxygenated VOCs (OVOCs), alkanes, and halogenated hydrocarbons (XVOCs). However, the concentrations of these three components decreased substantially during the CP (by 19 %, 18 %, and 11 %, respectively). The ozone formation potential (OFP) during the BCP was 144.47 ppbv, which was 1.2 times and 1.3 times higher than those during the ACP and CP periods, respectively. During the CP, the proportion of alkenes that contributed to the OFP decreased significantly by 24 %. Five types of VOCs sources were determined by positive matrix factorization (PMF): (1) solvent use, (2) biogenic, (3) secondary formation, (4) industrial process, and (5) vehicle exhaust and fuel evaporation sources. The VOCs emissions from industrial processes decreased by 54 % during the CP, whereas those from vehicle exhaust and fuel evaporation sources decreased by 36 %, indicating the effectiveness of emission control measures and the importance of these two sources for VOCs control in Xinxiang. In terms of regional transport, the results of the spatial analysis revealed that Hebi and Anyang in the northeast and Zhengzhou and Pingdingshan in the southwest, affected significantly the VOCs of Xinxiang. These results highlight the importance of controlling VOCs emissions in Xinxiang. Furthermore, attention should be paid to controlling the regional transport of surrounding cities.

Ammonia Abatement via Selective Oxidation over Electron-Deficient Copper Catalysts

Selective catalytic ammonia-to-dinitrogen oxidation (NH₃-SCO) is highly promising for the abatement of NH₃ emissions from flue gas purification devices. However, there is still a lack of high-performance and cost-effective NH₃-SCO catalysts for real applications. Here, highly dispersed, electron-deficient Cu-based catalysts were fabricated using nitrogen-doped carbon nanotubes (NCNT) as support. In NH₃-SCO catalysis, the Cu/NCNT outperformed Cu supported on N-free CNTs (Cu/OCNT) and on other types of supports (i.e., activated carbon, Al₂O₃, and zeolite) in terms of activity, selectivity to the desired product N₂, and H₂O resistance. Besides, Cu/NCNT demonstrated a better structural stability against oxidation and a higher NH₃ storage capacity (in the presence of H₂O vapor) than Cu/OCNT. Quasi in situ X-ray photoelectron spectroscopy revealed that the surface N species facilitated electron transfer from Cu to the NCNT support, resulting in electron-deficient Cu catalysts with superior redox properties, which are essential for NH₃-SCO catalysis. By temperature-programmed surface reaction studies and systematic kinetic measurements, we unveiled that the NH₃-SCO reaction over Cu/NCNT proceeded via the internal selective catalytic reaction (i-SCR) route; i.e., NH₃ was oxidized first to NO, which then reacted with NH₃ and O₂ to form N₂ and H₂O. This study paves a new route for the design of highly active, H₂O-tolerant, and low-cost Cu catalysts for the abatement of slip NH₃ from stationary emissions via selective oxidation to N₂.

Emission characteristics and ozone formation potentials of VOCs from ultra-low-emission waterborne automotive painting

Automotive painting plants are important emission sources of volatile organic compounds (VOCs) that contribute significantly to ground-level ozone (O₃) pollution in atmosphere. Here, we investigated process-specified emission characteristics of VOCs, without or with advanced adsorption/incineration after-treatments, from an ultra-low-emission (ULE) waterborne painting process in a modernized automotive plant. Overall, more than 80 VOCs species were identified and sorted into seven main categories. In the stack emissions without after-treatments, oxygenated VOCs (alcohols, esters, ketones, ethers, etc.) were found to be the most abundant components (48.8%), followed by aromatic (30.9%), alkanes (16.9%) and alkenes (1.2%). Among the different VOCs species discharged to atmosphere (i.e. after adsorption/incineration after-treatments), aromatics demonstrated a predominant contribution (by 60.6%) to the total O₃ formation potentials (OFPs) despite their relatively lower abundance. Trimethylbenzene was identified to have the highest OFPs, and thus should be controlled with peculiar priority. As compared to traditional organic solvent-based painting process, the ULE waterborne process implemented in the target plant allows to reduce the OFPs from 10.7 mg m^-3 to 3 mg m^-3 (or by 72%). Additional monitoring by unmanned aerial vehicle (over more than 3000 sampling points in the plant) confirmed that the instantaneous concentrations of fugitive VOCs were well below the regulated limit value during typical working and non-working days. These findings may provide important reference for reduction of VOCs emissions and O₃ pollution from automotive painting processes.

Effect of iron substitution in cryptomelane on the heterogeneous reaction with isoprene

Biogenic isoprene is an important pollutant for regional air quality. Being ubiquitously distributed on the earth surface, manganese (hydr)oxides should play a vital role in the transformation of isoprene. Cryptomelane is a typical manganese oxide with isomorphous substitution of Fe for Mn, but less attention has been paid to its heterogeneous reaction with isoprene. When Fe³⁺ replaces Mn³⁺, K⁺ is depleted and Mn³⁺ is oxidized to Mn⁴⁺. In contrast, oxygen vacancies are formed when Fe³⁺ substitutes Mn⁴⁺. Fe substitution creates weak crystallites and abundant mesopores, resulting in the increase of isoprene adsorption. As found by theoretical calculations, the Mn⁴⁺-O^2- bonds at the cross sections of the tunnels is more active than that on the outer wall of the tunnels. After the adsorption of isoprene, bridging carboxylate species and hydrogen-bonding water are produced and the surface octahedra are distorted, i.e., Mn⁴⁺O₆ → Mn³⁺O_6-δ. As the heat facilitates the breakage of Mn⁴⁺-O^2-, the increase of environmental temperature enhances the oxidation of isoprene. The above findings shed light on the effect of Fe substitution in cryptomelane to enhance the oxidation of isoprene, and illustrates that heterogeneous reaction with isoprene impairs the transformation of other environmental substances on cryptomelane.

Plasma-Catalytic CO2 Hydrogenation over a Pd/ZnO Catalyst: In Situ Probing of Gas-Phase and Surface Reactions

Plasma-catalytic CO₂ hydrogenation is a complex chemical process combining plasma-assisted gas-phase and surface reactions. Herein, we investigated CO₂ hydrogenation over Pd/ZnO and ZnO in a tubular dielectric barrier discharge (DBD) reactor at ambient pressure. Compared to the CO₂ hydrogenation using Plasma Only or Plasma + ZnO, placing Pd/ZnO in the DBD almost doubled the conversion of CO₂ (36.7%) and CO yield (35.5%). The reaction pathways in the plasma-enhanced catalytic hydrogenation of CO₂ were investigated by in situ Fourier transform infrared (FTIR) spectroscopy using a novel integrated in situ DBD/FTIR gas cell reactor, combined with online mass spectrometry (MS) analysis, kinetic analysis, and emission spectroscopic measurements. In plasma CO₂ hydrogenation over Pd/ZnO, the hydrogenation of adsorbed surface CO₂ on Pd/ZnO is the dominant reaction route for the enhanced CO₂ conversion, which can be ascribed to the generation of a ZnO _x overlay as a result of the strong metal-support interactions (SMSI) at the Pd-ZnO interface and the presence of abundant H species at the surface of Pd/ZnO; however, this important surface reaction can be limited in the Plasma + ZnO system due to a lack of active H species present on the ZnO surface and the absence of the SMSI. Instead, CO₂ splitting to CO, both in the plasma gas phase and on the surface of ZnO, is believed to make an important contribution to the conversion of CO₂ in the Plasma + ZnO system.

A high-performance and stable Cu/Beta for adsorption-catalytic oxidation in-situ destruction of low concentration toluene

Finding a cost-effective treatment to remove of low concentrations of volatile organic compounds (VOCs) is still a challenge. In this study, a Cu/Beta material was developed for in situ adsorption-catalytic oxidation of low concentrations of toluene. The results showed that the addition of Cu enhanced the adsorption and catalytic oxidation of toluene by Beta zeolite. Cu7/Beta with a Cu⁺ ratio of close to 50% performed best. The high adsorption of Cu7/Beta was mainly attributed to the abundant Cu⁺ species and the micro-mesoporous structure of the Beta zeolite, and the high catalytic oxidation was attributed to the lattice oxygen in the uniformly dispersed CuO. Finally, the adsorption intermediates and reaction pathways in the catalytic oxidation of toluene were clarified using XPS and DRIFTS spectra. This work provides new strategies for the development of efficient and stable adsorption-catalytic oxidation in situ destruction materials.

Cu-VWT Catalysts for Synergistic Elimination of NOx and Volatile Organic Compounds from Coal-Fired Flue Gas

A dual-function catalyst, designated as Cu5-VWT, has been constructed for the synergistic removal of NO_x and volatile organic compounds under complex coal-fired flue gas conditions. The removal of toluene, propylene, dichloromethane, and naphthalene all exceeded 99% (350 °C), and the catalyst could effectively block the generation of polycyclic aromatic hydrocarbons. Mechanistic studies have shown that Cu sites on the Cu5-VWT catalyst facilitate catalytic oxidation, while V sites facilitate NO_x reduction. Thus, toluene oxidation and NO_x reduction can proceed simultaneously. The removal of total hydrocarbons and nonmethane total hydrocarbons from 1200 m³·h^-1 real coal-fired flue gas by a monolithic catalyst were determined as 92 and 96%, respectively, much higher than those of 54 and 72% over a commercial VWT catalyst, indicating great promise for industrial application.

Quenching-induced surface modulation of perovskite oxides to boost catalytic oxidation activity

Quenching is a powerful method for modulating surface structures of metal oxide nanocatalysts to achieve high catalytic oxidation activities, but it is still challenging. Herein, a catalyst of ultrafine Co₃O₄ nanoparticles decorated on Co-doped LaMnO₃ (Co₃O₄/LaCo_xMn_1-xO₃) is synthesized via one-step quenching perovskite-type LaMnO₃ nanocatalyst into an aqueous solution of cobalt nitrate, which exhibits significantly improved catalytic performance with toluene (1000 ppm) conversion of 90% at 269 °C under the gas hourly space velocity of 72000 mL g^-1 h^-1. The high catalytic activity correlates with large surface area, abundant oxygen vacancies and good reducibility. Furthermore, density functional theory calculations disclose that Co doping and interfacial effect of Co₃O₄/LaCo_xMn_1-xO₃ can achieve lower C-H bond activation energy. These findings provide a unique and effective route towards surface modification of nanocatalysts.

Preparing hierarchical porous carbon with well-developed microporosity using alkali metal-catalyzed hydrothermal carbonization for VOCs adsorption

Biomass-derived porous carbonaceous materials are efficient adsorbents for VOCs, but their traditional preparation method, pyrolysis combined with activation, suffers from high energy consumption, equipment corrosion, and low pore-making efficiency, which hinders their large-scale practical application. A novel method of alkali metal-catalyzed hydrothermal carbonization coupling with chemical activation for the preparation of microporous carbon is presented. Porous carbon with well-developed microporosity deriving from corn husk were prepared through the hydrothermal carbonization using potassium persulfate (K₂S₂O₈) as a catalyst and programmed heating activation process. And the products were applied to removal of typical oxygen-containing VOCs, ethyl acetate. The addition of K₂S₂O₈ in hydrothermal carbonization accelerated the biomass hydrolysis, decomposed the biopolymer, and formed functional hydrochars. Potassium salts introduced into the hydrochars, which acted as an activator in this programmed heating activation process, formed a great deal of micropores. The specific surface area of micropores increased by 81%, and the specific surface area of micropores less than 1 nm increased by 180%. The introduction of K₂S₂O₈ in preparation improved the adsorption performance of CH-based porous carbons 16.46% and 60.00% respectively at different preparation temperatures (600 °C and 800 °C). Basing on these results, the improvement of micropores less than 1 nm is directly related to the adsorption performance. This indicates that pores (<1 nm) respond well to the adsorption of ethyl acetate.