Tailoring crystallization: towards high-performance poly(lactic acid)

Understanding the Impact of Chain Mobility on Conformational Evolution and Kinetics of Mesophase Formation in Poly(ʟ-lactide) under Low-Pressure CO2

Although the mesomorphic phase as an intermediate state has been introduced to understand polymer crystallization, the understanding of the mesomorphic phase is far from complete. Here, the effect of chain mobility on the mesophase structuring in melt-quenched poly(ʟ-lactide) (PLLA) treated in low-pressure CO2 at 1.6-2.0 MPa and 0 °C was investigated using infrared (IR) spectroscopy, differential scanning calorimetry (DSC), and atomic force microscopy (AFM). The IR and AFM results demonstrated that the final degree of order and the kinetics of structural evolution during the CO2-induced mesophase formation were critically dependent on the CO2 pressure. This was attributed to the distinct dynamics of conformational evolution (gg to gt conformer transition) due to the different CO2 pressures. The thermal behavior from the DSC results showed that CO2 pressure dominated both the scale and dynamics of the chain motion of PLLA. At a lower CO2 pressure of 1.6 MPa, smaller-scale segmental motion was not replaced by the larger-scale cooperative motion that occurred at a relatively higher CO2 pressure of 2 MPa, which was favorable for faster mesophase formation. Consequently, by inhibiting direct crystallization under limited mobility conditions, it was demonstrated that different chain mobility controlled by CO2 pressure and thus CO2 solubility impacted the dynamics of the mesophase formation of PLLA. The present results have implications for understanding the role of chain mobility in determining the intermediate structural phases in semicrystalline polymers.

A phenomenological model of pulsatile blood pressure-affected degradation of polylactic acid (PLA) vascular stent

The stent implantation may alter the post-operative patient's blood pressure, and bioresorbable vascular stents (BVS) as a candidate to treat vascular diseases, its degradation is affected by mechanical stress, thus, the altered pressure representing varying stress level will result in different degradation behaviors of the BVS. This paper first proposed a novel stress-regulated PLA degradation model that included swelling factor, and then the degradation evolutions of a PLA BVS within 180 days under normal and high blood pressures were simulated by finite element method, and more four degradation indexes were defined to study the effects of the two blood pressures on the degradation of the PLA BVS. The results showed that the high pressure weakly accelerated the degradation of the PLA BVS with respect to the normal pressure by examining the four indexes, e.g., the residual stent volumev r ( t ) decreased to 0.72 and 0.69, respectively for the normal and high pressures at day 180. The current finding provided a theoretical understanding of the PLA BVS degradation, and hinted that the PLA BVS may not need to be elaborately selected in clinical practices for treating hypertensive patients.

An integrated mechanical degradation model to explore the mechanical response of a bioresorbable polymeric scaffold

Simulation of bioresorbable medical devices is hindered by the limitations of current material models. Useful simulations require that both the short- and long-term response must be considered; existing models are not physically-based and provide limited insight to guide performance improvements. This study presents an integrated degradation framework which couples a physically-based degradation model, which predicts changes in both crystallinity (Xc) and molecular weight (Mn), with the results of a micromechanical model, which predicts the effective properties of the semicrystalline polymer. This degradation framework is used to simulate the deployment of a bioresorbable PLLA (Poly (L-lactide) stent into a mock vessel and the subsequent mechanical response during degradation under different diffusion boundary conditions representing neointimal growth. A workflow is established in a commercial finite element code that couples both the immediate and long-term responses. Clinically relevant lumen loss is reported and used to compare different responses and the effect of neo-intimal tissue regrowth post-implantation on degradation and on the mechanical response is assessed. In addition, the effects of possible changes in Xc, which could occur during processing and stent deployment, are explored.

Modified Biomass-Reinforced Polylactic Acid Composites

Polylactic acid (PLA), as a renewable and biodegradable green polymer material, is hailed as one of the most promising biopolymers capable of replacing petroleum-derived polymers for industrial applications. Nevertheless, its limited toughness, thermal stability, and barrier properties have restricted its extensive application. To address these drawbacks in PLA, research efforts have primarily focused on enhancing its properties through copolymerization, blending, and plasticization. Notably, the blending of modified biomass with PLA is expected not only to effectively improve its deficiencies but also to maintain its biodegradability, creating a fully green composite with substantial developmental prospects. This review provides a comprehensive overview of modified biomass-reinforced PLA, with an emphasis on the improvements in PLA's mechanical properties, thermal stability, and barrier properties achieved through modified cellulose, lignin, and starch. At the end of the article, a brief exploration of plasma modification of biomass is presented and provides a promising outlook for the application of reinforced PLA composite materials in the future. This review provides valuable insights regarding the path towards enhancing PLA.

Poly(lactic acid) stereocomplex microspheres as thermally tolerant optical resonators

Thermally tolerant polymer optical resonators are fabricated from a stereocomplex of poly(L-lactic acid) and poly(D-lactic acid) through the oil-in-water miniemulsion method. The thermal stability of the microspheres of the stereocomplex poly(lactic acid) (SC-PLA) is superior to that of the homochiral poly(lactic acid) (HC-PLA). As a result of the high thermal stability, the optical resonator properties of the SC-PLA microspheres are preserved at an elevated temperature of up to 230 °C, which is 70 °C higher than that of microspheres formed from HC-PLA.

Effect of particle size and environmental conditions on the release of di(2-ethylhexyl) phthalate from microplastics

The extensive use and improper handling of plastics have caused extensive microplastic (MP) pollution in terrestrial environments. Di(2-ethylhexyl) phthalate (DEHP), the main additive used in plastics, is toxic to organisms and may pose risks to human and animal reproductive functions. However, research on the release behavior of DEHP from MPs is scarce. In this study, the effects of particle size and environmental conditions (temperature, pH, ionic strength, and cation type) on DEHP release from polylactide (PLA), polystyrene (PS), and polyvinyl chloride (PVC) MPs were determined by performing leaching experiments. The results showed that when particle size decreased, the content of DEHP in the MPs and the amount of released DEHP increased though increasing specific surface area. An increase in temperature also promoted DEHP release; when the temperature increased from 15 °C to 45 °C, the amount of DEHP released from PLA, PS, and PVC increased by 38.4%, 71.0%, and 109%, respectively. The lower the crystallinity, the greater the increase in the amount of DEHP released. Ionic strength inhibited the release of DEHP from MPs. When Na+ concentration increased from 0 to 200 mM, the amount of DEHP released from PLA, PS, and PVC decreased by 27.4%, 41.6%, and 35.3%, respectively. The effect of Ca2+ on DEHP release from MPs was greater than that of Na+. In addition, the process of DEHP release from MPs fit well with a pseudo-first-order kinetic model. The results of this study provide a theoretical basis for managing and controlling the risks associated with plastic wastes.

Melt stretching and quenching produce low-crystalline biodegradable poly(lactic acid) filled with β-form shish for highly improved mechanical toughness

High-toughness biodegradable poly(lactic acid) (PLA) has always been intensively pursued on the way of replacing traditional petroleum-based plastics. Regulating microstructures to achieve self-toughening holds great promise due to avoidance of incorporating other heterogeneous components. Herein, we propose a straightforward and effective way to tailor microstructures and properties of PLA through melt-stretching and quenching of slightly crosslinked samples. The melt stretching drives chains orientation and crystallization at high temperature, while the quenching followed can freeze the crystallization process to any stage. For the first time, we prepare a type of transparent and low-crystalline PLA filled with rod-like β-form shish, which displays an outstanding tensile toughness, almost 17 times that of the conventional technique-processed one. This mechanical superiority is enabled by an integration of high ductility due to oriented chain network, and high tensile stress endowed by nanofibrous filler's role of β-form shish. Furthermore, the mechanically toughened PLA is demonstrated to generate the richest micro-cracks and shear bands under loading, which can effectively dissipate the deformational energy and underlie the high toughness. This work opens a new prospect for the bottom-up design of high-performance bio-based PLA materials that are tough, ductile and transparent by precise microstructural regulation through scalable melt processing route.

Bamboo fiber strengthened poly(lactic acid) composites with enhanced interfacial compatibility through a multi-layered coating of synergistic treatment strategy

In this study, a mild and eco-friendly synergistic treatment strategy was investigated to improve the interfacial compatibility of bamboo fibers with poly(lactic acid). The characterization results in terms of the chemical structure, surface morphology, thermal properties, and water resistance properties demonstrated a homogeneous dispersion and excellent interfacial compatibility of the treated composites. The excellent interfacial compatibility is due to multi-layered coating of bamboo fibers using synergistic treatment involving dilute alkali pretreatment, polydopamine coating and silane coupling agent modification. The composites obtained using the proposed synergistic treatment strategy exhibited excellent mechanical properties. Optimal mechanical properties were observed for composites with synergistically treated bamboo fiber mass proportion of 20 %. The tensile strength, elongation at break and tensile modulus of the treated composites were increased by 63.06 %, 183.04 % and 259.04 %, respectively, compared to the untreated composites. This synergistic treatment strategy and the remarkable performance of the treated composites have a wide range of applicability in bio-composites (such as industrial packaging, automotive lightweight interiors, and consumer goods).

Mechanical Properties and Non-Isothermal Crystallization Kinetics of Polylactic Acid Modified by Polyacrylic Elastomers and Cellulose Nanocrystals

In this paper, a polyacrylic elastomer latex with butyl acrylate (BA) as the core and methyl methacrylate (MMA) copolymerized with glycidyl methacrylate (GMA) as the shell, named poly(BA-MMA-GMA) (PBMG), was synthesized by seeded emulsion polymerization. Cellulose nanocrystal (CNC) was dispersed in the polyacrylic latex to prepare PBMG/CNC dispersions with different CNC contents. The dried product was mixed with polylactic acid (PLA) to fabricate PLA/PBMG/CNC blends. The addition of PBMG and PBMG/CNC improved the mechanical properties of the PLA matrix. Differential scanning calorimetry (DSC) was used to investigate the non-isothermal crystallization kinetics. The Avrami equation modified by the Jeziorny, Ozawa and Mo equations was used to analyze the non-isothermal crystallization kinetics of PLA and its blends. Analysis of the crystallization halftime of non-isothermal conditions indicated that the overall rate of crystallization increased significantly at 1 wt% content of CNC. This seemed to result from the increase of nucleation density and the acceleration of segment movement in the presence of the CNC component. This phenomenon was verified by polarizing microscope observation.

Three/Four-Dimensional Printed PLA Nano/Microstructures: Crystallization Principles and Practical Applications

Compared to traditional methods, three/four-dimensional (3D/4D) printing technologies allow rapid prototyping and mass customization, which are ideal for preparing nano/microstructures of soft polymer materials. Poly (lactic acid) (PLA) is a biopolymer material widely used in additive manufacturing (AM) because of its biocompatibility and biodegradability. Unfortunately, owing to its intrinsically poor nucleation ability, a PLA product is usually in an amorphous state after industrial processing, leading to some undesirable properties such as a barrier property and low thermal resistance. Crystallization mediation offers a most practical way to improve the properties of PLA products. Herein, we summarize and discuss 3D/4D printing technologies in the processing of PLA nano/microstructures, focusing on crystallization principles and practical applications including bio-inspired structures, flexible electronics and biomedical engineering mainly reported in the last five years. Moreover, the challenges and prospects of 3D/4D printing technologies in the fabrication of high-performance PLA materials nano/microstructures will also be discussed.

Polylactic Acid/Calcium Stearate Hydrocharging Melt-Blown Nonwoven Fabrics for Respirator Applications

Non-biodegradable polypropylene, which poses a serious threat to the environment, is the most utilized material in air filtration systems. Moreover, under conditions of high temperature and high humidity, the electrostatic charge in melt-blown nonwoven fabrics treated with traditional corona electrets will quickly dissipate. Here, biodegradable polylactic acid, calcium stearate, and an innovative hydrocharging technique are reported to develop environmentally friendly polylactic acid/calcium stearate hydrocharging melt-blown nonwoven fabrics with high charge stability. Compared with polylactic acid melt-blown nonwoven fabrics, the crystallization structure and charge storage of polylactic acid/calcium stearate melt-blown nonwoven fabrics have been greatly improved due to the presence of calcium stearate. In PM0.3, it exhibited a high filtration efficiency (96.78%), a low pressure drop (65.20 Pa), and a good quality factor (0.053 Pa-1), which can meet the N95 respirator standard. Furthermore, it is worth mentioning that the filtration performance remained at a high level (>95.00%) after 2 months. Importantly, based on the test and analysis of surface electrostatic potential, crystallization, and charge storage and distribution, we proposed plausible charge generation and stable storage mechanisms. It demonstrated more potential for electret air filtration and smart respirators as the further possible step of research in the field.

Study on the crystallization behavior and conformation adjustment scale of poly(lactic acid) in the terahertz frequency range

The observed properties of crystalline polymers are determined by their internal structure, which in turn is the result of their different crystallization behaviors. Here, we investigate the crystallization behavior of poly(lactic acid) (PLA) by terahertz time-domain spectroscopy (THz-TDS) at varied temperatures. We find that the changes in the chain packing and conformation of PLA are characterized by THz spectroscopy. Combining X-ray diffraction (XRD) and infrared spectroscopy (IR), we attributed the blue-shift of the THz peak to the tightness of the chain packing, while its absorption enhancement is caused by the conformation transition. The effects of chain packing and chain conformation on the characteristic peak are phased. Furthermore, absorption discontinuities of the characteristic peaks of PLA crystallized at different temperatures are observed, which originated from differences in the degree of conformational transition caused by different thermal energies. We find that the crystallization temperature at which the absorption mutation of PLA occurs corresponds to the temperature at which the motion of the segment and molecular chain is excited, respectively. At these two temperatures, PLA exhibits different scales of conformational transitions leading to stronger absorption and larger absorption changes at higher crystallization temperatures. The results demonstrate that the driving force of PLA crystallization is indeed from changes in chain packing and chain conformation, and the molecular motion scale can also be characterized by THz spectroscopy.

The synergistic effect of heterogeneous nucleation and stress-induced crystallization on supramolecular structure and performances of poly(lactic acid) melt-spun fibers

As a kind of bio-based polymer, poly (lactic acid) has potential application in fibers fields. Due to the weak nucleation ability, PLA crystallizes slowly and forms large spherulites during the forming process, which deteriorates the properties of PLA fibers. In this work, melt-spun method is employed for the fabrication of PLA/T composite fibers using succinate diphenyl dihydrazide (TMC-306) as the nucleating agent, and then the hot-drawing and heat setting is performed to the as-spun fibers. Compared with pure PLA fibers, PLA/T fibers show faster crystallization rate and improved performance due to the synergistic effect of heterogeneous nucleation and stress-induced crystallization. The characterization of non-isothermal crystallization behavior indicates that the peak crystallization temperature as well as crystallinity of PLA composites is increased to 121.5 °C and 36.78 % respectively by blending 0.3 wt% TMC-306. Meanwhile, the obtained PLA/0.3T composite fibers are highly crystallized and oriented at hot-drawing ratio of 2.4 folds and heat setting temperature of 100 °C, and the conformational stability is noticeably enhanced. Further, the tensile strength and storage modulus of PLA/0.3T composite fiber are 3.46 cN/dtex and 46,953 MPa respectively, which are increased by 42 % and 41 % compared with neat PLA fibers.

A new class of nucleating agents for poly(L-lactic acid): Environmentally-friendly metal salts with biomass-derived ligands and advanced nucleation ability

Adding nucleating agents has been a successful strategy to boost the heat resistance of poly(L-lactic acid) (PLLA) by increasing the crystallinity. In this study, a new series of bio-based complexes as nucleating agents for PLLA, including twelve combinations of three eco-friendly metal ions (Zn, Mg, Ca) and four biomass-derived α-hydroxy acids, were successfully synthesized to respectively investigate the effects of metal ions as well as ligands on nucleation capacity of complexes. By investigating the non-isothermal and isothermal crystallization at 135 °C of PLLA with 0.3 wt% loading of complexes, both zinc and magnesium salts of L-mandelic acid showed excellent nucleation capacities. And magnesium L-mandelate performed better, raising the crystallinity of PLLA to 44.4 % as well as minimizing its crystallization half-time from 73 min to 2.7 min. The growth and denser distribution of PLLA spherulites on the salt surface were also observed by POM, reflecting epitaxial nucleation as the possible mechanism. A novel inspiration, utilizing VESTA software to simulate the crystal structure of zinc L-mandelate (Zn(L-MA)₂), was proposed to determine the nucleation mechanism. Also, using polyethylene terephthalate (PET) as a test protocol, the rationality of the model could be approved by checking the fitness of nucleating prediction and experiment results.

The Structural Evolution and Mechanical Properties of Semi-Aromatic Polyamide 12T after Stretching

The development of semi-aromatic polyamides with excellent mechanical properties has always been a popular research avenue. In this work, the semi-aromatic polyamide 12T (PA12T) with the maximum tensile strength of 465.5 MPa was prepared after stretching at 210 °C 4.6 times. Wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) were used to characterize the structural evolution of semi-aromatic polyamide 12T (PA12T) after stretching at different stretching temperatures and stretching ratios. The formation mechanism of this change in mechanical properties was investigated from different aspects of the aggregated structure such as crystal morphology, crystal orientation and crystallinity. The relevant characterization results show that the crystal structure, crystal orientation and crystallinity of PA12T were the highest when the sample was pre-stretched at 210 °C, which is crucial for improving the mechanical properties of PA12T. These findings will provide important guidance for the preparation of polymer materials with excellent mechanical properties.

Polylactic Acid Chemical Foaming Assisted by Solid-State Processing: Solid-State Shear Pulverization and Cryogenic Milling

A chemical foaming process of polylactic acid (PLA) was developed via the solid-state processing methods of solid-state shear pulverization (SSSP) and cryogenic milling. Based on the ability of solid-state processing to enhance the crystallization kinetics of PLA, chemical foaming agents (CFA) are first compounded before foaming via compression molding. Specifically, the effects of the pre-foaming solid-state processing method and CFA concentration were investigated. Density reduction, mechanical properties, thermal behavior, and cell density of PLA foams are characterized. Solid-state processing of PLA before foaming greatly increases the extent of PLA foaming by achieving void fractions approximately twice that of the control foams. PLA's improved ability to crystallize is displayed through both dynamic mechanical analysis and differential scanning calorimetry. The solid-state-processed foams display superior mechanical robustness and undergo low stress relaxation. The cell density of the PLA foams also increases with solid-state processing, especially through SSSP. Additionally, crosslinking of PLA during the pre-foaming processing step is found to result in the greatest enhancement of crystallization but decreased void fraction and foam effectiveness. Overall, SSSP and cryogenic milling show significant promise in improving chemical foaming in alternative biopolymers.

Effect of Crystallization on Shape Memory Effect of Poly(lactic Acid)

The opportunity for the preparation of high-performance shape memory materials was brought about by the excellent mechanical properties of poly(lactic acid) (PLA). As the effect of crystallization on shape memory was still unclear, this brings constraints to the high-performance design of PLA. The PLA plates with different aggregation structure were prepared by three kinds of molding methods in this paper. The PLA plates were pre-stretched with a series of different strains above glass transition temperature (i.e., 70 °C). The recovery stress and ratio of the material were measured above stretching temperature (i.e., 80 °C). Prolonging of annealing time resulted in more perfect crystal structure and higher crystallinity. The crystal region acted as network nodes in shape memory PLA, and crystal region structure determined the shape memory performance. Based on the experimental results, the structural evolution of network nodes in shape memory PLA was established.

Modification of Cellulose Micro- and Nanomaterials to Improve Properties of Aliphatic Polyesters/Cellulose Composites: A Review

Aliphatic polyesters/cellulose composites have attracted a lot attention due to the perspectives of their application in biomedicine and the production of disposable materials, food packaging, etc. Both aliphatic polyesters and cellulose are biocompatible and biodegradable polymers, which makes them highly promising for the production of “green” composite materials. However, the main challenge in obtaining composites with favorable properties is the poor compatibility of these polymers. Unlike cellulose, which is very hydrophilic, aliphatic polyesters exhibit strong hydrophobic properties. In recent times, the modification of cellulose micro- and nanomaterials is widely considered as a tool to enhance interfacial biocompatibility with aliphatic polyesters and, consequently, improve the properties of composites. This review summarizes the main types and properties of cellulose micro- and nanomaterials as well as aliphatic polyesters used to produce composites with cellulose. In addition, the methods for noncovalent and covalent modification of cellulose materials with small molecules, polymers and nanoparticles have been comprehensively overviewed and discussed. Composite fabrication techniques, as well as the effect of cellulose modification on the mechanical and thermal properties, rate of degradation, and biological compatibility have been also analyzed.

A facile strategy for preparation of strong tough poly(lactic acid) foam with a unique microfibrillated bimodal micro/nano cellular structure

This work reports the design and fabrication of strong tough poly(lactic acid) (PLA) foam by combining pressure-induced-flow (PIF) processing with supercritical CO₂ foaming. PIF processing widened the foaming window of PLA to 40-120 °C, while supercritical CO₂ foaming released the undesired internal stress of PLA samples with PIF processing (P-PLA). The prepared PLA foams displayed a unique microfibrillated bimodal micro/nano cellular structure which is strongly affected by saturation temperature (T_s). Both micron and nano cells showed decreasing cells size and increasing cell density as T_s elevated. The orientation factor as well as internal stress of PLA foams decreased with increased T_s. Compared with P-PLA samples, PLA foam prepared at T_s of 40 °C showed negligible reduction of orientation from 0.45 to 0.41 and release of internal stress characterized by the rightward shift of Raman peak (stretching vibration of CO bond from 1763 to 1766 cm^-1). Furthermore, PLA foam prepared at T_s of 40 °C presented excellent impact strength (32.3 kJ/m²), tensile strength (42.0 MPa), and ductility (14.2%). The combination of PIF processing and supercritical CO₂ foaming provides a facile and effective method to prepare strong tough PLA foam that has immense potential in biomedical, aerospace, automotive, and other structural applications.

Substantially Enhanced Stereocomplex Crystallization of Poly(L-Lactide)/Poly(D-Lactide) Blends by the Formation of Multi-Arm Stereo-Block Copolymers

Stereocomplex-type polylactide (SC-PLA) created by alternate packing of poly(L-lactide) (PLLA) and poly(D-lactide) (PDLA) chains in a crystalline state has emerged as a growingly popular engineering bioplastic that possesses excellent hydrolytic stability and thermomechanical properties. However, it is extremely difficult to acquire high-performance SC-PLA products via melt-processing of high-molecular-weight PLLA/PDLA blends because both SC crystallites and homocrystallites (HCs) are competitively formed in the melt-crystallization. Herein, a facile yet powerful way was employed to boost SC formation by introducing trace amounts of some epoxy-functionalized small-molecule modifiers into the enantiomeric blends during reactive melt-blending. The results show that the SC formation is considerably enhanced with the in situ generation of multi-arm stereo-block PLA copolymers, based on the reaction between epoxy groups of the modifiers and hydroxyl end groups of PLAs. More impressively, it is intriguing to find that the introduction of only 0.5 wt% modifiers can induce exclusive SC formation in the blends upon isothermal and non-isothermal melt-crystallizations. The outstanding SC crystallizability might be attributed to the suppressing effect of such unique copolymers on the separation of the alternately arranged PLLA/PDLA chain segments in molten state as a compatibilizer. Furthermore, the generation of these copolymers does not result in a significant increase in melt viscosity of the blends. These findings suggest new opportunities for the high-throughput processing of SC-PLA materials into useful products.

The isothermal crystallization kinetic of poly(L-lactide)-block-poly(ethylene glycol) block copolymers (PLLA-PEG): Effect of block lengths of PEG and PLLA

Poly(ethylene glycol)-block-poly(L-lactide) (PEG-PLLA) is a biodegradable copolymer which widely applied to medicine and drug system, and the morphology, organization and mechanical properties were extensively investigated. However, the crystallization kinetic were...

Polylactic Acid Piezo-Biopolymers: Chemistry, Structural Evolution, Fabrication Methods, and Tissue Engineering Applications

Polylactide acid (PLA), as an FDA-approved biomaterial, has been widely applied due to its unique merits, such as its biocompatibility, biodegradability, and piezoelectricity. Numerous utilizations, including sensors, actuators, and bio-application-its most exciting application to promote cell migration, differentiation, growth, and protein-surface interaction-originate from the piezoelectricity effect. Since PLA exhibits piezoelectricity in both crystalline structure and an amorphous state, it is crucial to study it closely to understand the source of such a phenomenon. In this respect, in the current study, we first reviewed the methods promoting piezoelectricity. The present work is a comprehensive review that was conducted to promote the low piezoelectric constant of PLA in numerous procedures. In this respect, its chemistry and structural origins have been explored in detail. Combining any other variables to induce a specific application or to improve any PLA barriers, namely, its hydrophobicity, poor electrical conductivity, or the tuning of its mechanical properties, especially in the application of cardiovascular tissue engineering, is also discussed wherever relevant.

An experimental investigation into the physical, thermal and mechanical degradation of a polymeric bioresorbable scaffold

This study presents a comprehensive evaluation of the mechanical, micro-mechanical and physical properties of Reva Medical Fantom Encore Bioresorbable Scaffolds (BRS) subjected to a thermally-accelerated degradation protocol. The Fantom Encore BRS were immersed in phosphate buffered saline solution at 50 °C for 112 days with radial compression testing, nanoindentation, differential scanning calorimetry, gel permeation chromatography and mass loss characterisation performed at consecutive time points. In the initial stages of degradation (Days 0-21), the Fantom Encore BRS showed increases in radial strength and stiffness, despite a substantial reduction in in molecular weight, with a slight increase in the melt temperature also observed. In the second phase (Days 35-54), the radial strength of the BRS samples were maintained despite a continued loss in molecular weight. However, during this phase, the ductility of the stent showed a reduction, with stent fracture occurring earlier in the crimp process and with lower amounts of plastic deformation evident under visual examination post-fracture. In the final phase (Days 63-112), the load-bearing capacity of the Fantom Encore BRS showed continued reduction, with decreases in radial stiffness and strength, and drastic reduction in the work-to-fracture of the devices. Throughout each phase, there was a steady increase in the relative crystallinity, with limited mass loss until day 112 and only minor changes in glass transition and melt temperatures. Limited changes were observed in nano-mechanical properties, with measured local elastic moduli and hardness values remaining largely similar throughout degradation. Given that the thermally-accelerated in vitro conditions represented a four-fold acceleration of physiological conditions, these results suggest that the BRS scaffolds could exhibit substantially brittle behaviour after ∼ one year of implantation.

Cellulose Isolated From Waste Rubber Wood and Its Application in PLA Based Composite Films

Waste rubber wood (RW) is the castoff of rubber plantation with abundant reservation but without high-value utilization. In this study, cellulose with high purity has been efficiently isolated from waste RW and further processed into cellulose nanocrystals. By means of acetylation, more hydrophobic cellulose-based products, namely acetylated rubber wood cellulose (Ac-RWC) and acetylated rubber wood cellulose nanocrystals (Ac-RW-CNC) had been attempted as reinforcing fillers for fabricating two series of PLA-based composite films via spin coating instead of currently prevailing melt compounding technique. To ensure a uniformed dispersion of fillers in PLA matrix, the addition of reinforcing filler should be equal to or less than 5% based on the film dry weight. Compared with pure PLA film, the Ac-RWC reinforced PLA composite films are more thermally stable, while the Ac-RW-CNC reinforced PLA composite films on the other hand exhibit more enhanced performance in mechanical properties and the degree of crystallinity. The highest tensile strength (55.0 MPa) and Young's modulus (3.9 GPa) were achieved for 5%Ac-RW-CNC/PLA composite film.

Physical and mechanical degradation behaviour of semi-crystalline PLLA for bioresorbable stent applications

This study presents a systematic evaluation of the physical, thermal and mechanical performance of medical-grade semi-crystalline PLLA undergoing thermally-accelerated degradation. Samples were immersed in phosphate-buffered saline solution at 50 °C for 112 days and mass loss, molecular weight, thermal properties, degree of crystallinity, FTIR and Raman spectra, tensile elastic modulus, yield stress and failure stress/strain were evaluated at consecutive time points. Samples showed a consistent reduction in molecular weight and melting temperature, a consistent increase in percent crystallinity and limited changes in glass transition temperature and mass loss. At day 49, a drastic reduction in tensile failure strain was observed, despite the fact that elastic modulus, yield and tensile strength of samples were maintained. Brittleness increase was followed by rapid increase in degradation rate. Beyond day 70, samples became too brittle to test indicating substantial deterioration of their load-bearing capacity. This study also presents a computational micromechanics framework that demonstrates that the elastic modulus of a semi-crystalline polymer undergoing degradation can be maintained, despite a reducing molecular weight through compensatory increases in percent crystallinity. This study presents novel insight into the relationship between physical properties and mechanical performance of medical-grade PLLA during degradation and could have important implications for design and development of bioresorbable stents for vascular applications.