Meso/macroporous nitrogen-doped carbon architectures with iron carbide encapsulated in graphitic layers as an efficient and robust catalyst for the oxygen reduction reaction in both acidic and alkaline solutions

Nickel-Nitrogen Doped MnO2 as Oxygen Reduction Reaction Catalyst for Aluminum Air Batteries

Aluminum-air battery has the advantages of high energy density, low cost and environmental protection, and is considered as an ideal next-generation energy storage conversion system. However, the slow oxygen reduction reaction (ORR) in air cathode leads to its unsatisfactory performance. Here, we report an electrode made of N and Ni co-doped MnO2 nanotubes. In alkaline solution, Ni/N-MnO2 has higher oxygen reduction activity than undoped MnO2, with an initial potential of 1.00 V and a half-wave potential of 0.75 V. This is because it has abundant defects, high specific surface area and sufficient Mn3+ active sites, which promote the transfer of electrons and oxygen-containing intermediates. Density functional theory (DFT) calculations show that MnO2 doped with N and Ni atoms reduces the reaction overpotential and improves the ORR kinetics. The peak power density and energy density of the Ni/N-MnO2 air electrode increased by 34.03 mW cm-2 and 316.41 mWh g-1, respectively. The results show that N and Ni co-doped MnO2 nanotubes are a promising air electrode, which can provide some ideas for the research of aluminum-air batteries.

Tailored interface engineering of Co3Fe7/Fe3C heterojunctions for enhancing oxygen reduction reaction in zinc-air batteries

The rational construction of highly active and robust non-precious metal oxygen reduction electrocatalysts is a vital factor to facilitate commercial applications of Zn-air batteries. In this study, a precise and stable heterostructure, comprised of a coupling of Co3Fe7 and Fe3C, was constructed through an interface engineering-induced strategy. The coordination polymerization of the resin with the bimetallic components was meticulously regulated to control the interfacial characteristics of the heterostructure. The synergistic interfacial effects of the heterostructure successfully facilitated electron coupling and rapid charge transfer. Consequently, the optimized CST-FeCo displayed superb oxygen reduction catalytic activity with a positive half-wave potential of 0.855 V vs. RHE. Furthermore, the CST-FeCo air electrode of the liquid zinc-air battery revealed a large specific capacity of 805.6 mAh gZn-1, corresponding to a remarkable peak power density of 162.7 mW cm-2, and a long charge/discharge cycle stability of 220 h, surpassing that of the commercial Pt/C catalyst.

Carbothermal Reduction-Assisted Synthesis of a Carbon-Supported Highly Dispersed PtSn Nanoalloy for the Oxygen Reduction Reaction

Exploring high-performance and low-platinum-based electrocatalysts to accelerate the oxygen reduction reaction (ORR) at the air cathode of zinc-air batteries remains crucial. Herein, by combining electroless deposition and carbothermal reduction, a nitrogen-doped carbon-supported highly dispersed PtSn alloy nanocatalyst (PtSn/NC) was prepared for a high-efficiency ORR process. Electrochemical measurements show that PtSn/NC exhibits excellent electrocatalytic ORR activity with a half-wave potential of 0.850 V versus reversible hydrogen electrode (RHE), which is higher than that of commercial Pt/C (0.815 V). The PtSn/NC-based (20 μgPt cm-2) rechargeable Zn-air battery exhibited astonishing performance with a maximum power density of up to 150.1 mW cm-2, as well as excellent rate performance and charge/discharge stability. Physical characterization reveals that carbothermal reduction could compel the transformation of Sn oxide into metallic Sn, which then alloys with the deposited Pt atoms to form the PtSn nanoalloy, in which electrons are transferred from Sn atoms to neighboring Pt atoms, thereby improving the ability of Pt-based active sites to catalyze the ORR process in PtSn/NC by optimizing the unoccupied d-band of Pt atoms. This work provides a reliable and innovative route for the rational design of highly dispersed Pt-based alloy ORR electrocatalysts.

Catalytic effects of graphene structures on Pt/graphene catalysts

Pt/C catalysts have been considered the ideal cathodic catalyst for proton exchange membrane fuel cells (PEMFCs) due to their superior oxygen reduction reaction (ORR) catalytic activity at low temperatures. However, oxidation and corrosion of the carbon black support at the cathode result in the agglomeration of Pt particles, which reduces the active sites in the Pt/C catalyst. Graphene supports have shown great promise to address this issue, and therefore, finding out the main structural features of the graphene support is of great significance for guiding the rational construction of graphene-based Pt (Pt/graphene) catalysts for optimized ORR catalysts. In order to systematically study the influence of the structural features of the graphene support on the electro-catalytic properties of Pt/graphene catalysts, we prepared porous nitrogen-doped reduced graphene oxide (P-NRGO), nitrogen-doped reduced graphene oxide (NRGO), treated P-NRGO (TP-NRGO) and reduced graphene oxide (RGO) with different nitrogen species contents (7.76, 7.54, 3.24, and 0.14 at%), oxygen species contents (18.68, 18.12, 6.34 and 21.12 at%), specific surface areas (370.4, 70.6, 347.7 and 276.2 m2 g-1) and pore volumes (1.366, 0.1424, 1.3299 and 1.0414 cm3 g-1). The ORR activity of the four Pt/graphene catalysts when listed in the order of their half-wave potentials (E 1/2) and peak power densities was found to be as Pt/P-NRGO > Pt/NRGO > Pt/TP-NRGO > Pt/RGO. The long-term durability of Pt/P-NRGO for the operation of H2-air PEMFCs is better than that of commercial Pt/C catalysts. The excellent ORR catalytic performance of Pt/P-NRGO compared to that of the other three Pt/graphene catalysts is ascribed to the high nitrogen species content of P-NRGO that can facilitate the uniform dispersion of Pt particles and provide accessible active sites for ORR. The results indicate that the specific surface area (SSA) and heteroatom dopants have strong influence on the Pt particle size, and that the nitrogen species of graphene supports play a more important role than the oxygen species, specific surface area and pore volume for the Pt/graphene catalysts in providing accessible active sites.

F Doping-Induced Multicomponent Synergistic Active Site Construction toward High-Efficiency Bifunctional Oxygen Electrocatalysis for Rechargeable Zn-Air Batteries

The commercialization of rechargeable Zn-air batteries (ZABs) relies on the material innovation to accelerate the sluggish oxygen electrocatalysis kinetics. Due to the differentiated mechanisms of reverse processes, i.e., oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), rationally integrating dual sites for bifunctional oxygen electrocatalysis is prerequisite yet remains challenging. Herein, multicomponent synergistic active sites within highly graphitic carbon substrate are exquisitely constructed, which is accomplished by fluorine (F) modulation strategy. The incorporation of F dopants facilitates pyridinic N formation for anchoring single metal sites, thus guaranteeing the coexistence of sufficient M-Nx sites and metal nanoparticles toward bifunctional oxygen electrocatalysis. As a result, the optimal catalyst, denoted as F NH2-FeNi-800, outperforms commercial Pt/C+RuO2 with smaller gap between Ej = 10 and E1/2 (ΔE) of 0.63 V (vs 0.7 V for Pt/C+RuO2), demonstrating its superior bifunctionality. Beyond that, its superiority is validated in homemade rechargeable ZABs. ZABs assembled using F NH2-FeNi-800 as the air cathode delivers higher peak power density (123.8 mW cm-2) and long-cycle lifetime (over 660 cycles) in comparison with Pt/C@RuO2 (68.8 mW cm-2; 300 cycles). The finding not only affords a highly promising oxygen electrocatalyst, but also opens an avenue to constructing multifunctional active sites for heterogeneous catalysts.

Polypyrrole regulates Active Sites in Co-based Catalyst in Direct Borohydride Fuel Cells

Direct borohydride fuel cells (DBFCs) convert borohydride (NaBH4) chemical energy into clean electricity. However, catalytic active site deactivation in NaBH4 solution limits their performance and stability. We propose a strategy to regulate active sites in Co-based catalysts using polypyrrole modification (Co-PX catalyst) to enhance electrochemical borohydride oxidation reaction (eBOR). As an anode catalyst, the synthesized Co-PX catalyst exhibits excellent eBOR performance in DBFCs, with current density of 280 mA ⋅ cm-2 and power density of 151 mW ⋅ cm-2, nearly twice that of the unmodified catalyst. The Co-PX catalyst shows no degradation after 120-hour operation, unlike the rapidly degrading control. In-situ electrochemical attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIRS) and density functional theory (DFT) suggest that polypyrrole-modified carbon support regulate the charge distribution, increasing oxidation state and optimizing adsorption/desorption of intermediates. A possible reaction pathway is proposed. This work presents a promising strategy for efficient polymer-modulated catalysts in advanced DBFCs.

Fe3 C/Fe Decorated N-doped Carbon Derived from Tetrabutylammonium tetrachloroferrate Complex as Bifunctional Electrocatalysts for ORR, OER and Zn-Air Batteries in Alkaline Medium

The emergence of non-precious metal-based robust and economic bifunctional oxygen electrocatalysts for both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is crucial for the rational design of commercial rechargeable Zn-air batteries (RZAB) with safe energy conversion and storage systems. Herein, a facile strategy to fabricate a cost-efficient, bifunctional oxygen electrocatalyst Fe3 C/Fe decorated N doped carbon (FeC-700, the catalyst prepared at carbinization temperature of 700 °C) with a unique structure has been developed by carbonization of a single source precursor, tetrabutylammonium tetrachloroferrate(III) complex. The ORR and OER activity revealed excellent performance (ΔE=0.77 V) of the FeC-700 electrocatalyst, comparable to commercial Pt/C and RuO2, respectively. The designed temperature-tuneable structure provided sufficiently accessible active sites for the continuous passage of electrons by shortening the mass transfer pathway, leading to extremely durable electrocatalysts with high ECSA and amazing charge transfer performance. Remarkably, the assembled Zn-air batteries with the FeC-700 catalyst as the bifunctional air electrode delivers gratifying charging-discharging ability with an impressive power density of 134 mW cm-2 with a long lifespan, demonstrating prodigious possibilities for practical application.

Silver Metal-Organic Framework Derived N-Doped Carbon Nanofibers for CO2 Conversion into β-Oxopropylcarbamates

Developing efficient heterogeneous catalysts for chemical fixation of CO2 to produce high-value-added chemicals under mild conditions is highly desired but still challenging. Herein, we first reported an approach to prepare a novel catalyst (Ag@NCNFs), featuring Ag nanoparticles (NPs) embedded within porous nitrogen-doped carbon nanofibers (NCNFs), via growing a Ag metal-organic framework on one-dimensional electrospun nanofibers followed by pyrolysis. Benefiting from the abundant nitrogen species and porous structure, Ag NPs is well dispersed in the obtained Ag@NCNFs. Catalytic studies indicated that Ag@NCNFs exhibited excellent catalytic activity for the three-component coupling reaction of CO2, secondary amines, and propargylic alcohols to generate β-oxopropylcarbamates under mild conditions with a turnover number (TON) of 16.2, and it can be recycled and reused at least 5 times without an obvious decline in catalytic activity. The reaction mechanism was clearly clarified by FTIR, NMR, 13C isotope labeling, control experiments, and density functional theory calculations. The results suggest that Ag@NCNFs and 1,8-diazabicyclo[5.4.0]undec-7-ene can synergistically activate propargylic alcohol to react with CO2, and then the generated α-alkylidene cyclic carbonate was invaded by secondary amine to produce β-oxopropylcarbamate. Importantly, to the best of our knowledge, this is the first experimental and theoretical investigation on this reaction.

Activating doped graphene surface by cobalt-rich sulfide encapsulation toward oxygen reduction electrocatalysis

Similar to proton exchange membrane fuel cell, anion-exchange membrane fuel cell is also a significant energy conversion device for achieving the utilization of clean hydrogen energy. However, the cathodic alkaline oxygen reduction reaction (ORR) is kinetically not favored and usually requires platinum-group metal (PGM) catalysts such as Pt/C to reduce the overpotential. The major challenge in using PGM-free catalysts for ORR is their low efficiency and poor stability, which urgently demands new concepts and strategies to address this issue. Herein, we controllably manufactured a N, S-co doped graphene encapsulating uniform cobalt-rich sulfides (Co8FeS8@NSG) by a universal synthesis strategy. After encapsulation, electron transfer from the encapsulated cobalt-rich sulfides to the doped graphene was greatly promoted, which effectively optimizes the electronic structure of the doped graphene, thereby enhancing the ORR activity of the doped graphene surface. Consequently, the Co8FeS8@NSG exhibits enhanced ORR activity with a higher half-wave potential of 0.868 V (versus reversible hydrogen electrode, vs. RHE) when compared with pure NSG (0.765 V vs. RHE). Density functional theory calculations further confirm that the construction of interface for NSG encapsulating cobalt-rich sulfides could conspicuously elevate the ORR activity through slightly positively-charged C active site and thus simultaneously enhancing electronic conductivity.

α-NiO/Ni(OH)2/AgNP/F-Graphene Composite for Energy Storage Application

The α-NiO/Ni(OH)₂/AgNP/F-graphene composite, which is silver nanoparticles preanchored on the surface of fluorinated graphene (AgNP/FG) and then added to α-NiO/Ni(OH)₂, is investigated as a potential battery material. The addition of AgNP/FG endows the electrochemical redox reaction of α-NiO/Ni(OH)₂ with a synergistic effect, resulting in enhanced Faradaic efficiency with the redox reactions of silver accompanied by the OER and the ORR. It resulted in enhanced specific capacitance (F g^-1) and capacity (mA h g^-1). The specific capacitance of α-NiO/Ni(OH)₂ increased from 148 to 356 F g^-1 with the addition of AgNP(20)/FG, while it increased to 226 F g^-1 with the addition of AgNPs alone without F-graphene. The specific capacitance of α-NiO/Ni(OH)₂/AgNP(20)/FG further increased up to 1153 F g^-1 with a change in the voltage scan rate from 20 to 5 mV/s and the Nafion-free α-NiO/Ni(OH)₂/AgNP(20)/FG composite. In a similar trend, the specific capacity of α-NiO/Ni(OH)₂ increased from 266 to 545 mA h g^-1 by the addition of AgNP(20)/FG. The performance of hybrid Zn-Ni/Ag/air electrochemical reactions by α-NiO/Ni(OH)₂/AgNP(200)/FG and Zn-coupled electrodes indicates a potential for a secondary battery. It results in a specific capacity of 1200 mA h g^-1 and a specific energy of 660 W h kg^-1, which is divided into Zn-Ni reactions of ∼95 W h kg^-1 and Zn-Ag/air reactions of ∼420 W h kg^-1, while undergoing a Zn-air reaction of ∼145 W h kg^-1.

Iron/cobalt-decorated nitrogen-rich 3D layer-stacked porous biochar as high-performance oxygen reduction air-cathode catalyst in microbial fuel cell

Developing low-cost and high-efficiency oxygen reduction reaction (ORR) catalysts is crucial to the commercial application of microbial fuel cell (MFC). Herein, Fe/Co-decorated nitrogen-rich three-dimensional (3D) layer-stacked porous biochar (Fe/Co-NC-x) have been synthesized from silk gel through secondary carbonization of activated carbons which firstly adsorbed metal ions. The multilayer porous structure of Fe/Co-NC-3 contributes to construction of high specific surface area (576 m² g^-1), large pore volume (1.27 cm³ g^-1) and many defect structure (I_D/I_G = 1.004). As expected, with Fe/Co synergistic effect, Fe/Co-NC-3 exhibits excellent ORR performance through 4e^- pathway with good methanol resistance. In addition, the performance of MFC using Fe/Co-NC-3 as air-cathode catalyst is more prominent with higher maximum power density (1059.62 ± 30.00 mW m^-2) compared to that using NC (668.19 ± 9.84 mW m^-2) and commercial Pt/C catalyst (957.33 ± 10.50 mW m^-2). Therefore, Fe/Co-NC-3 should be a prospective catalyst in the practical application of fuel cells and other energy devices.

Synthesis of hierarchically structured Fe3C/CNTs composites in a FeNC matrix for use as efficient ORR electrocatalysts

Fe-N-C has a high number of FeN _x active sites and has thus been regarded as a high-performance oxygen reduction reaction (ORR) catalyst, and combining Fe₃C with Fe-N-C typically boosts ORR activity. However, the catalytic mechanism remains unknown, limiting further research and development. In this study, a precipitation-solvothermal process was used in conjunction with pyrolysis to produce a series of Fe-N-C catalysts derived from a zeolitic imidazolate framework (ZIF) that was composited with Fe₃C. The prepared catalysts had a multiscale structure of ZIF-like carbon particles and rod-like structures, as well as bamboo-like carbon nanotubes (CNTs) and carbon layers wrapped with Fe₃C particles while a series of studies revealed the origin of the rod-like structures and Fe₃C phase. The hierarchical structure was beneficial to the enhanced electrocatalytic performance of catalysts for ORR. The optimal sample had the highest half-wave potential of 0.878 V vs. RHE, which was higher than that of commercial Pt/C (0.861 V vs. RHE). The ECSA of the optimal sample was 1.08 cm² μg^-1, with an electron transfer number close to 4, and functioning kinetics. The optimal sample exhibited high durability and methanol tolerance for the ORR. Finally, blocking different Fe active sites with coordination ions demonstrated that Fe(ii) was the main active site, indicating that Fe₃C primarily served as a cocatalyst to optimize the electron structure of Fe-N-C, thereby synergistically improving the ORR activity.

PtFeCoNiCu high-entropy solid solution alloy as highly efficient electrocatalyst for the oxygen reduction reaction

Searching for an efficient, durable, and low cost catalyst toward oxygen reduction reaction (ORR) is of paramount importance for the application of fuel cell technology. Herein, PtFeCoNiCu high-entropy alloy nanoparticles (PFCNC-HEA) is reported as electrocatalyst toward ORR. It shows remarkable ORR catalytic mass activity of 1.738 A mg^-1 _Pt at 0.90 V, which is 15.8 times higher than that of the state-of-art commercial Pt/C catalyst. It also exhibits outstanding stability with negligible voltage decay (3 mV) after 10k cycles accelerated durability test. High ORR activity is ascribed to the ligand effect caused by polymetallic elements, the optimization of the surface electronic structure, and the formation of multiple active sites on the surface. In the proton exchange membrane fuel cell setup, this cell delivers a power density of up to 1.380 W cm^-2 with a cathodic Pt loading of 0.03 mg_Pt cm^-2, demonstrating a promising catalyst design direction for highly efficient ORR.

Revealing the Real Role of Etching during Controlled Assembly of Nanocrystals Applied to Electrochemical Reduction of CO2

In recent years, the use of inexpensive and efficient catalysts for the electrocatalytic CO₂ reduction reaction (CO₂RR) to regulate syngas ratios has become a hot research topic. Here, a series of nitrogen-doped iron carbide catalysts loaded onto reduced graphene oxide (N-Fe₃C/rGO-H) were prepared by pyrolysis of iron oleate, etching, and nitrogen-doped carbonization. The main products of the N-Fe₃C/rGO-H electrocatalytic reduction of CO₂ are CO and H₂, when tested in a 0.5 M KHCO₃ electrolyte at room temperature and pressure. In the prepared catalysts, the high selectivity (the Faraday efficiency of CO was 40.8%, at −0.3 V), and the total current density reaches ~29.1 mA/cm² at −1.0 V as demonstrated when the mass ratio of Fe₃O₄ NPs to rGO was equal to 100, the nitrogen doping temperature was 800 °C and the ratio of syngas during the reduction process was controlled by the applied potential (−0.2~−1.0 V) in the range of 1 to 20. This study provides an opportunity to develop nonprecious metals for the electrocatalytic CO₂ reduction reaction preparation of synthesis and gas provides a good reference

A Flower-like In2O3 Catalyst Derived via Metal-Organic Frameworks for Photocatalytic Applications

The most pressing concerns in environmental remediation are the design and development of catalysts with benign, low-cost, and efficient photocatalytic activity. The present study effectively generated a flower-like indium oxide (In₂O₃-MF) catalyst employing a convenient MOF-based solvothermal self-assembly technique. The In₂O₃-MF photocatalyst exhibits a flower-like structure, according to morphology and structural analysis. The enhanced photocatalytic activity of the In₂O₃-MF catalyst for 4-nitrophenol (4-NP) and methylene blue (MB) is likely due to its unique 3D structure, which includes a large surface area (486.95 m² g^-1), a wide spectrum response, and the prevention of electron-hole recombination compared to In₂O₃-MR (indium oxide-micro rod) and In₂O₃-MD (indium oxide-micro disc). In the presence of NaBH₄ and visible light, the catalytic performances of the In₂O₃-MF, In₂O₃-MR, and In₂O₃-MD catalysts for the reduction of 4-NP and MB degradation were investigated. Using In₂O₃-MF as a catalyst, we were able to achieve a 99.32 percent reduction of 4-NP in 20 min and 99.2 percent degradation of MB in 3 min. Interestingly, the conversion rates of catalytic 4-NP and MB were still larger than 95 and 96 percent after five consecutive cycles of catalytic tests, suggesting that the In₂O₃-MF catalyst has outstanding catalytic performance and a high reutilization rate.

Heteroatom-Doped Carbon-Encapsulated FeP Nanostructure: A Multifunctional Electrocatalyst for Zinc-Air Battery and Water Electrolyzer

The rational design and synthesis of efficient multifunctional electrocatalysts for renewable energy technologies is of significant interest. Herein, we demonstrate a novel approach for the synthesis of a nitrogen and phosphorus dual-doped mesoporous carbon-encapsulated iron phosphide (FeP@NPC) nanostructure and its multifunctional electrocatalytic activity toward an oxygen reduction reaction, oxygen evolution reaction, and hydrogen evolution reaction for zinc-air battery (ZAB) and alkaline water-splitting applications. FeP@NPC is obtained by the carbothermal reduction of the precursor complex [Fe(bpy)₃](PF₆)₂ in the presence of melamine without any traditional phosphidating agent. The PF₆^- counteranion is used for the phosphidation of Fe. FeP@NPC obtained at 900 °C (FeP@NPC-900) exhibits excellent bifunctional oxygen electrocatalytic performance with a very low potential gap (ΔE = E_1/2^ORR - E_j10^OER) of 670 mV. The ZAB device delivers a peak power density of 190.15 mW cm^-2 (iR-corrected), specific capacity of 785 mA h g_Zn^-1, and energy density of 706.5 Wh kg_Zn^-1 at 50 mA cm^-2. The ZAB exhibits excellent charge-discharge cycling stability for over 35 h with negligible voltaic efficiency loss (0.9%). Three CR2032 coin-cell-based ZABs made of an FeP@NPC-900 air cathode connected in series power 81 LEDs for 15 min. FeP@NPC-900 also has promising electrocatalytic activity toward water splitting in acidic as well as in alkaline pH. The benchmark current density of 10 mA cm^-2 is achieved with a two-electrode alkaline water electrolyzer at a cell voltage of 1.65 V. ZAB-powered water electrolyzer is made by integrating two rechargeable ZABs connected in series with the two-electrode water electrolyzer. The ZAB powers the electrolyzer for 24 h without a significant loss in the open-circuit voltage. The catalyst retains its initial structural integrity even after continuous water electrolysis for 24 h.

Recent Advances in ZIF-Derived Atomic Metal-N-C Electrocatalysts for Oxygen Reduction Reaction: Synthetic Strategies, Active Centers, and Stabilities

Exploring highly active, stable electrocatalysts with earth-abundant metal centers for the oxygen reduction reaction (ORR) is essential for sustainable energy conversion. Due to the high cost and scarcity of platinum, it is a general trend to develop metal-N-C (M-N-C) electrocatalysts, especially those prepared from the zeolite imidazolate framework (ZIF) to replace/minimize usage of noble metals in ORR electrocatalysis for their amazingly high catalytic efficiency, great stability, and readily-tuned electronic structure. In this review, the most pivotal advances in mechanisms leading to declined catalytic performance, synthetic strategies, and design principles in engineering ZIF-derived M-N-C for efficient ORR catalysis, are presented. Notably, this review focuses on how to improve intrinsic ORR activity, such as M-N_x -C_y coordination structures, doping metal-free heteroatoms in M-N-C, dual/multi-metal sites, hydrogen passivation, and edge-hosted M-N_x . Meanwhile, how to increase active sites density, including formation of M-N complex, spatial confinement effects, and porous structure design, are discussed. Thereafter, challenges and future perspectives of M-N-C are also proposed. The authors believe this instructive review will provide experimental and theoretical guidance for designing future, highly active ORR electrocatalysts, and facilitate their applications in diverse ORR-related energy technologies.

A Novel Electrochemical Immunosensor Based on COF-LZU1 as Precursor to Form Heteroatom-Doped Carbon Nanosphere for CA19-9 Detection

Porous carbon sphere materials have a large variety of applications in several fields due to the large surface area, adaptable porosity, and good conductivity they possess. Obtaining a steady carbon sphere using the green synthesis method remains a significant challenge. In this experiment, covalent organic frameworks (COFs) were used as a precursor and Fe₃O₄NPs were integrated into the precursor in order to synthesize a porous carbon sphere material using the one-step pyrolysis method. COFs have an ordered porous structure, perpetual porosity, large surface area, and low density and display good environmental tolerance. These properties make them an excellent precursor for synthesizing porous carbon sphere, which maintains good morphology at high temperatures, and it is not involved in the removal of dangerous reagent and small size restrictions during the synthesis process. In addition to the formation of a porous carbon sphere, transition metal carbon material that contains N element can be an active catalyst. The composites exhibit better activity when Fe is doped into carbon materials containing N element than that of other doped transition metals including Mn and Co. In this situation, the integration of Fe₃O₄NPs and N element in the COF precursor exposed the active sites of the composites and the two substances synergistically improved the electrocatalytic properties, and the composites were named Fe₃O₄@NPCS. The constructed Fe₃O₄@NPCS/GCE immunosensor was applied as a means of detecting CA19-9 antigen and presented a wide linear range from 0.00001 to 10 U/mL with a low detection limit of 2.429 μU/mL (S/N = 3). In addition, the prepared immunosensor was utilized for detecting CA19-9 antigen in the real human serum, and the recovery rates were in the range from 95.24% to 106.38%. Therefore, a porous carbon sphere prepared by COFs as a precursor can be applied for the detection of CA19-9 antigen in real samples, which could be an excellent strategy for CA19-9 antigen detection and could potentially promote the development of COF materials in various electrochemical fields.

Nanostructured transition-metal phthalocyanine complexes for catalytic oxygen reduction reaction

Oxygen reduction reaction (ORR) plays a key role in the field of fuel cells. Efficient electrocatalysts for the ORR are important for fuel cells commercialization. Pt and its alloys are main active materials for ORR. However, their high cost and susceptibility to time-dependent drift hinders their applicability. Satisfactory catalytic activity of nanostructured transition metal phthalocyanine complexes (MPc) in ORR through the occurrence of molecular catalysis on the surface of MPc indicates their potential as a replacement material for precious-metal catalysts. Problems of MPc are analyzed on the basis of chemical structure and microstructure characteristics used in oxygen reduction catalysis, and the strategy for controlling the structure of MPc is proposed to improve the catalytic performance of ORR in this review.

Magnetized manganese-doped watermelon rind biochar as a novel low-cost catalyst for improving oxygen reduction reaction in microbial fuel cells

Microbial fuel cells (MFCs) are promising equipment for water treatment and power generation. The catalyst used in the oxygen reduction reaction (ORR) at the cathode is a critical factor for efficacy of MFCs. Therefore, it is important to develop cost-effective cathode catalysts to enhance application of MFCs. In the current study, a novel cathode catalyst was developed, which was annealed with watermelon rind as raw material and transition metals including iron, and manganese were introduced. The 700Mn/Fe@WRC catalyst, which was annealed at 700 °C, exhibited excellent electrochemical performance. The high relative content of pyridine nitrogen caused by the inherent nitrogen element of the watermelon rind and the high content of iron and manganese elements introduced resulted in increase in electrochemical surface area to 657.6 m²/g. The number of electrons transferred ORR was 3.96, indicating that ORR occurs through a four-electron pathway. The maximum power density of MFCs was 399.3 ± 7.4 mW/m² with a fitting total internal resistance of 15.242 Ω, and the removal efficiency of COD was 97.1 ± 1.2%. The cost of the 700Mn/Fe@WRC catalyst was approximately 0.15 $/g, which is significantly lower compared with Pt/C (33.0 $/g). Experimental verification showed that the 700Mn/Fe@WRC prepared using the economical watermelon rind biochar (WRC) is an excellent substitute for non-precious metal catalysts used in MFCs.

Magnetic Nanoparticles: Synthesis, Anisotropy, and Applications

Anisotropy is an important and widely present characteristic of materials that provides desired direction-dependent properties. In particular, the introduction of anisotropy into magnetic nanoparticles (MNPs) has become an effective method to obtain new characteristics and functions that are critical for many applications. In this review, we first discuss anisotropy-dependent ferromagnetic properties, ranging from intrinsic magnetocrystalline anisotropy to extrinsic shape and surface anisotropy, and their effects on the magnetic properties. We further summarize the syntheses of monodisperse MNPs with the desired control over the NP dimensions, shapes, compositions, and structures. These controlled syntheses of MNPs allow their magnetism to be finely tuned for many applications. We discuss the potential applications of these MNPs in biomedicine, magnetic recording, magnetotransport, permanent magnets, and catalysis.

Coordination regulated pyrolysis synthesis of ultrafine FeNi/(FeNi)9S8 nanoclusters/nitrogen, sulfur-codoped graphitic carbon nanosheets as efficient bifunctional oxygen electrocatalysts

Design of advanced carbon nanomaterials with high-efficiency oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activities is still imperative yet challenging for searching green and renewable energies. Herein, we synthesized ultrafine FeNi/(FeNi)₉S₈ nanoclusters encapsulated in nitrogen, sulfur-codoped graphitic carbon nanosheets (FeNi/(FeNi)₉S₈/N,S-CNS) by coordination regulated pyrolyzing the mixture of the metal precursors, dithizone and g-C₃N₄ at 800 °C. The as-prepared FeNi/(FeNi)₉S₈/N,S-CNS exhibited distinct electrocatalytic activity and stability for the ORR with positive onset (E_onset) and half-wave (E_1/2) potentials (E_onset = 0.97 V; E_1/2 = 0.86 V) and OER with the small overpotential (η = 283 mV) at 10 mA cm^-2 in the alkaline media, outperforming commercial Pt/C and RuO₂ catalysts. This research provides some constructive guidelines for preparing efficient, low-cost and stable nanocatalysts for electrochemical energy devices.

Fe2P encapsulated in carbon nanowalls decorated with well-dispersed Fe3C nanodots for efficient hydrogen evolution and oxygen reduction reactions

The development of cost-effective, high-efficiency bifunctional electrocatalysts as alternatives to the state-of-the-art Pt-based materials toward the hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR) is of great significance but still challenging. Herein, an advanced bifunctional electrocatalyst is presented, composed of Fe₂P encapsulated in carbon nanowalls decorated with well-dispersed Fe₃C nanodots (denoted as Fe₂P@Fe₃C/CNTs), which is achieved by a novel "inside-out" gas-solid reaction protocol. When functioning as a cathodic catalyst for water splitting, the Fe₂P@Fe₃C/CNT catalyst needs an ultralow overpotential of 83 mV to deliver a current density of 10 mA cm^-2, shows a small Tafel slope of 53 mV dec^-1 and ensures long-term stability for over 200 h in an alkaline electrolyte. Notably, the Fe₂P@Fe₃C/CNT catalyst exhibits an extremely impressive ORR performance with an onset potential (E_onset) of 1.060 V and a half-wave potential (E_1/2) of 0.930 V, excellent stability (≈94% activity retention after 36 000 s), and a strong methanol resistance ability, even far outperforming commercial Pt/C (E_onset = 0.955 V, E_1/2 = 0.825 V, ≈75% activity retention after less than 3500 s). Such outstanding HER and ORR performances are mainly ascribed to the improved corrosion resistance of the unique Fe₂P@C core-shell structures, the abundant catalytically active sites of ultrasmall Fe₃C nanodots incorporated in carbon nanowalls, and the good electrical conductivity of 2D graphitic carbon nanotubes used as a support.

Elucidating the Active Site and the Role of Alkali Metals in Selective Hydrodeoxygenation of Phenols over Iron-Carbide-based Catalyst

Iron-carbide-based catalysts have been explored in the selective hydrodeoxygenation (HDO) of phenol, aiming at elucidating the role of active site and alkali metal. Complementary characterization such as X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, and scanning transmission electron microscopy coupled with electron energy loss spectroscopy, together with catalytic evaluations revealed a rapid structural reconstruction of iron carbide (Fe₃ C) catalysts, leading to a stable defective graphene-covered metallic Fe active phase (G@Fe) under reaction conditions. Further studies using different alkali metals (i. e., Na, K, and Cs) revealed that alkali metals showed negligible effect on the phase transformation of Fe₃ C. However, the reconstructed G@Fe doped with alkali metals inhibited the tautomerization, a facile reaction pathway to saturation of the aromatic ring, leading to enhanced selectivity to arene. The extent of inhibition of tautomerization or selectivity to arene was closely related to the degree of electron donation of alkali metal to Fe.

Kinetic Insights into the Mechanism of Oxygen Reduction Reaction on Fe2O3/C Composites

Since the inception of cobalt phthalocyanine for oxygen reduction reaction (ORR), non-platinum group metals have been the central focus in the area of fuel-cell electrocatalysts. Besides Fe-N_x active sites, a large variety of species are formed during the pyrolysis, but studies related to their ORR activity have been given less importance in the literature. Fe₂O₃ is one among them, and this study describes the role of Fe₂O₃ in the ORR. The Fe₂O₃ is carefully synthesized on various carbon supports and characterized using X-ray photoelectron spectroscopy (XPS) spectra, high-resolution transmission electron microscopy (HRTEM) images, and surface area analysis. The characterization techniques reveal that the Fe₂O₃ nanoparticles are present in the pores of the carbon supports, having a particle size ranging from 4 to 15 nm. The current density of the ORR on Fe₂O₃/C catalysts is increased compared with bare carbon supports, as discerned from the rotating ring-disk electrode (RRDE) voltammetry experiments, demonstrating the role of size-confined Fe₂O₃ nanoparticles. The overall number of electrons in the ORR is increased by the introduction of Fe₂O₃ on the carbon support. Based on the kinetic analysis, the ORR on Fe₂O₃/C follows a pseudo-4-electron or 2+2-electron ORR, where the first 2-electron ORR to H₂O₂ and second 2-electron H₂O₂ reduction reaction (HPRR) to H₂O are assigned to the graphitic carbon (carbon defects) and Fe₂O₃ active sites, respectively. Theoretical studies indicate that the role of Fe₂O₃ is to decrease the free energy of O₂ adsorption and reduce the energy barrier for the reduction of *OOH to OH^-. The onset potential estimated from the free energy diagram is 0.42 V, matching with the HPRR activity demonstrated using the potential-dependent rate constants plot. Fe₂O₃/C shows higher stability by retaining 95% of the initial activity even after 20 000 cycles.

Single-Atom Catalysts: A Perspective toward Application in Electrochemical Energy Conversion

Single-atom catalysts (SACs) hold great promise for maximized metal utilization, exceptional tunability of the catalytic site, and selectivity. Moreover, they can substantially contribute to lower the cost and abundancy challenges associated with raw materials. Significant breakthroughs have been achieved over the past decade, for instance, in terms of synthesis methods for SACs, their catalytic activity, and the mechanistic understanding of their functionality. Still, great challenges lie ahead in order to render them viable for application in important fields such as electrochemical energy conversion of renewable electrical energy. We have identified three particular development fields for advanced SACs that we consider crucial, namely, the scale-up of the synthesis, the understanding of their performance in real devices such as fuel cells and electrolyzers, and the understanding and mitigation of their degradation. In this Perspective, we review recent activities of the community and provide our outlook with respect to the aspects required to bring SACs toward application.

Facile construction of S-containing Co-based metal organic framework core-shell microspheres as an efficient bifunctional oxygen electrocatalyst

A cost-effective non-noble metal bifunctional electrocatalyst towards the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) is very important for energy-related applications. Micro/nanomaterials with core-shell structures have emerged as potential non-noble metal catalyst candidates. Herein, an efficient bifunctional oxygen electrocatalyst, S-containing Co-based metal organic framework core-shell microspheres (Co-MOF-CSMSs), has been designed and constructed by using 2,2':5',2''-terthiophene-5,5''-dicarboxylic acid as a novel ligand through a facile one-step hydrothermal method. Due to the integrated favorable structural characteristics of the core-shell structure and MOFs for electrocatalysis, Co-MOF-CSMSs are revealed as a good bifunctional electrocatalyst for the ORR and OER, including an onset potential of 0.93 V vs. RHE (reversible hydrogen electrode), a half-wave potential of 0.78 V vs. RHE and an overpotential of 0.35 V at 10 mA cm^-2. This work provides a low-cost and facile method to design and construct advanced micro/nanomaterials with core-shell structures to targetedly develop high-performance bifunctional oxygen electrocatalysts.

CoFe alloy embedded in N-doped carbon nanotubes derived from triamterene as a highly efficient and durable electrocatalyst beyond commercial Pt/C for oxygen reduction

For development of green and sustainable energy, it is of importance to search highly efficient and low-cost electrocatalysts of oxygen reduction reaction (ORR) in energy conversion devices. Herein, CoFe alloyed nanocrystals embedded in N-doped bamboo-like carbon nanotubes (CoFe@NCNTs) were facilely synthetized by one-step co-pyrolysis with the mixture of triamterene, metal chlorides and graphitic carbon nitride (g-C₃N₄). The resultant CoFe@NCNTs exhibited excellent ORR activity with the positive shifts in the onset potential (E_onset = 0.97 V) and half-wave potential (E_1/2 = 0.88 V), outperforming commercial Pt/C (E_onset = 0.96 V; E_1/2 = 0.84 V). Compared to metal organic frameworks (MOFs)-based strategy for synthesis of low-cost carbon-based ORR catalysts, this method is simple and convenient, coupled by avoiding the complicated synthesis of MOFs and its ligands. This work provides a promising route to fabricate advanced transition-metal-based carbon catalysts in the researches correlated with energy conversion devices.

A defect-rich ultrathin MoS2/rGO nanosheet electrocatalyst for the oxygen reduction reaction

The structural properties such as high specific surface area, good electrical conductivity, rich-defects of the catalyst surface guarantee outstanding catalytic performance and durability of oxygen reduction reaction (ORR) electrocatalysts. It is still a challenging task to construct ORR catalysts with excellent performance. Herein, we have reported column-like MoS2/rGO with defect-rich ultrathin nanosheets prepared by a convenient solvothermal method. The structure and composition of MoS2/rGO are systematically investigated. MoS2/rGO shows a remarkable electrocatalytic performance, which is characterized by an outstanding onset potential of 0.97 V, a half-wave potential of 0.83 V, noticeable methanol tolerance, and durability of 93.7% current retention, superior to commercial Pt/C. The ORR process occurring on MoS2/rGO is a typical four electron pathway. Therefore, this study achieves the design of a low-cost, highly efficient and stable nonprecious metal ORR electrocatalyst in alkaline media.

Metal-Free B, N co-Doped Hierarchical Porous Carbon Electrocatalyst with an Excellent O2 Reduction Performance

Fuel cells have attracted increasing attention due to their low cost, high energy density, low environmental pollution, and abundant raw materials. Oxygen reduction reaction (ORR) is a core technology of fuel cells, and the development of new electrocatalysts with high ORR performance is highly desirable. Herein, we synthesize a series of B, N co-doped hierarchical porous carbons using a soft template method with the integration of self-assembly, calcination and etching. The obtained materials exhibit hierarchical porous structures, controllable pore distribution, partial graphite structures, and B, N co-doping. They can function as the cost-effective and metal-free electrocatalysts, facilitating the diffusion of electrolyte ions and the improvement of ORR performance. Especially, the B, N co-doped porous carbon with the B-to-N molar ratio of 5 (BNC-5) displays a high ORR activity with a half-wave potential (E1/2 ) of 0.73 V, an onset potential (Eonset ) of 0.94 V, and a high limiting current density (JL ) of 5.98 mA cm-2 , superior to the N-doped C (NC) and BNC-1 (the B-to-N molar ratio=1), BNC-3 (the B-to-N molar ratio=3) and BNC-7 (the B-to-N molar ratio=7) under the identical conditions. Moreover, the BNC-5 exhibits good cycling stability after 5000 cyclic voltammetry (CV) cycles and excellent tolerance toward even 3 M methanol. This research provides a new approach for the facile synthesis of dual element-doped carbon electrocatalysts with high ORR performance.

Surface-confinement assisted synthesis of nitrogen-rich single atom Fe-N/C electrocatalyst with dual nitrogen sources for enhanced oxygen reduction reaction

The utilization of earth abundant iron and nitrogen doped carbon as a precious-metal-free electrocatalyst for oxygen reduction reaction (ORR) significantly depends on the rational design and construction of desired Fe-N_xmoieties on carbon substrates, which however remains an enormous challenge. Herein a typical nanoporous nitrogen-rich single atom Fe-N/C electrocatalyst on carbon nanotube (NR-CNT@FeN-PC) was successfully prepared by using CNT as carbon substrate, polyaniline (PANI) and dicyandiamine (DCD) as binary nitrogen sources and silica-confinement-assisted pyrolysis, which not only facilitate rich N-doping for the inhibition of the Fe agglomeration and the formation of single atom Fe-N_xsites in carbon matrix, but also generate more micropores for enlarging BET specific surface area (up to 1500 m²·g^-1). Benefiting from the advanced composition, nanoporous structure and surface hydrophilicity to guarantee the sufficient accessible active sites for ORR, the NR-CNT@FeN-PC catalyst under optimized conditions delivers prominent ORR performance with a half-wave potential (0.88 V versus RHE) surpass commercial Pt/C catalyst by 20 mV in alkaline electrolyte. When assembled in a home-made Zn-air battery device as cathodic catalyst, it achieved a maximum output power density of 246 mW·cm^-2and a specific capacity of 719 mA·h·g^-1_Znoutperformed commercial Pt/C catalyst, holding encouraging promise for the application in metal-air batteries.

Co/CoOx heterojunctions encapsulated N-doped carbon sheets via a dual-template-guided strategy as efficient electrocatalysts for rechargeable Zn-air battery

Developing highly efficient oxygen electrocatalysts is of vital importance for rechargeable Zn-air batteries (ZABs). Herein, Co/CoO_x nano-heterojunctions encapsulated into nitrogen-doped carbon sheets (NCS@Co/CoO_x) are fabricated via a dual-template-guided approach by using zeolitic imidazolate frameworks (ZIFs) as templates. The synergistic integration of structural and compositional advantages endows such catalyst with superior catalytic properties to benchmark noble-metal catalysts. To be specific, the hierarchical micro/mesopores affords massive mass transport channels and maximizes the exposure of accessible active sites, whereas the NCS matrix accelerates electron transfer and prevents the self-aggregation of active species during the electrocatalytic reaction. Moreover, abundant and synergistic Co-based active sites (CoO, Co₃O₄, Co-N_x) greatly promote the catalytic activity. As the cathode of both liquid and flexible solid-state ZABs, excellent device properties are achieved, outperforming those assembled with commercial Pt/C+RuO₂ catalyst. This work presents a feasible and cost-effective strategy for developing oxygen electrocatalysts derived from ZIFs templates.

Carbon-Supported Single-Atom Catalysts for Formic Acid Oxidation and Oxygen Reduction Reactions

The commercialization of fuel cells, especially for direct formic acid fuel cells (DFAFCs) and proton-exchange membrane fuel cells (PEMFCs), is significantly restrained by the high cost, poor stability, and sluggish kinetics of platinum group metals (PGM) catalysts for both the anodic formic acid oxidation reaction (FAOR) and the cathodic oxygen reduction reaction (ORR). Currently, it has confronted with challenges, including exploring highly active, cost-effective, and stable catalysts to replace PGM for DFAFCs and PEMFCs. Recently, the increasing investigation has been focused on the single-atom catalysts (SACs) to enhance the catalytic performance owing to the maximum atom utilization and highly exposed active sites. The aim of this review is to present the recent research activities on carbon supported SACs. At the beginning of the review, metal-based SACs supported on different carbon supports, and the typical characterization methods are introduced. Subsequently, recent advances in metal-based SACs for FAOR and ORR catalysis are scientifically summarized. Particularly, some representative metal-based SACs for ORR activity are further exemplified with a deeper understanding of structure-activity relationships. Finally, the challenges and opportunities of SACs are prospected, such as the mechanism understanding and commercial applications.

One-step pyrolysis synthesis of nitrogen, manganese-codoped porous carbon encapsulated cobalt-iron nanoparticles with superior catalytic activity for oxygen reduction reaction

Replacing precious metal catalysts with low-price and abundant catalysts is one of urgent goals for green and sustainable energy development. It is imperative yet challenging to search low-cost, high-efficiency, and long-durability electrocatalysts for oxygen reduction reaction (ORR) in energy conversion devices. Herein, three-dimensional low-cost Co₃Fe₇ nanoparticles/nitrogen, manganese-codoped porous carbon (Co₃Fe₇/N, Mn-PC) was synthesized with the mixture of dicyandiamide, cobalt (II) tetramethoxyphenylporphyrin (Co(II)TMOPP), hemin, and manganese acetate by one-step pyrolysis and then acid etching. The resultant Co₃Fe₇/N, Mn-PC exhibited excellent durability and prominent ORR activity with more positive onset potential (E_onset, 0.98 V) and half-wave potential (E_1/2, 0.87 V) in 0.1 M KOH electrolyte, coupled with strong methanol resistance. The pyrolysis temperature and optimal balance of graphite with pyridine-nitrogen are of significance for the ORR performance. The prepared Co₃Fe₇/N, Mn-PC displayed excellent ORR performance over commercial Pt/C in the identical environment. It was ascribed to the uniform 3D architecture, Mn- and N-doping effects by finely adjusting the electronic structures, coupled with the synergistic catalytic effects of multi-compositions and multi-active sites. This work provides some constructive guidelines for preparation of low-cost and high-efficiency ORR electrocatalysts.