Tailored Combinatorial Microcompartments through the Self‐Organization of Microobjects: Assembly, Characterization, and Cell Studies

Buzza DM. Programmable 2D materials through shape-controlled capillary forces

In recent years, self-assembly has emerged as a powerful tool for fabricating functional materials. Since self-assembly is fundamentally determined by the particle interactions in the system, if we can gain full control over these interactions, it would open the door for creating functional materials by design. In this paper, we exploit capillary interactions between colloidal particles at liquid interfaces to create two-dimensional (2D) materials where particle interactions and self-assembly can be fully programmed using particle shape alone. Specifically, we consider colloidal particles which are polygonal plates with homogeneous surface chemistry and undulating edges as this particle geometry gives us precise and independent control over both short-range hard-core repulsions and longer-range capillary interactions. To illustrate the immense potential provided by our system for programming self-assembly, we use minimum energy calculations and Monte Carlo simulations to show that polygonal plates with different in-plane shapes (hexagons, truncated triangles, triangles, squares) and edge undulations of different multipolar order (hexapolar, octopolar, dodecapolar) can be used to create a rich variety of 2D structures, including hexagonal close-packed, honeycomb, Kagome, and quasicrystal lattices. Since the required particle shapes can be readily fabricated experimentally, we can use our colloidal system to control the entire process chain for materials design, from initial design and fabrication of the building blocks, to final assembly of the emergent 2D material.

Investigation of the Orientation and Assembly of Functionalized Microcubes at the Oil-Water Interface

The dependence of the preferred orientation of polystyrene microcubes on surface hydrophobicity at the water/hexadecane interface is reported. Similar to the water/air interfaces, the microcubes were shown to reside at the water/hexadecane interface with three distinct orientations: face-up, edge-up, and vertex-up. Concomitantly, ordered aggregates with flat plate, tilted linear, and close-packed hexagonal structures were formed, driven by capillary force. With increasing the hydrophobicity of five sides of the cubes, the preferential microcube orientation at the water/hexadecane interface changed sequentially from face-up to edge-up, to vertex-up, then back to edge-up, and to face-up. This dependence of the preferential microcube orientation on surface hydrophobicity at the water/hexadecane interface differs from that observed at the water/air interface, where the preferential orientation changed only from face-up to edge-up, then to vertex-up, as surface hydrophobicity increased. In addition, preformed microcube assemblies at the water/air interface could be dynamically reconfigured by replacing the air phase with hexadecane under stirring.

Impact of Surface Area on Sensitivity in Autonomously Reporting Sensing Hydrogel Nanomaterials for the Detection of Bacterial Enzymes

The rapid and selective detection of bacterial contaminations and bacterial infections in a non-laboratory setting using advanced sensing materials holds the promise to enable robust point-of-care tests and rapid diagnostics for applications in the medical field as well as food safety. Among the various possible analytes, bacterial enzymes have been targeted successfully in various sensing formats. In this current work, we focus on the systematic investigation of the role of surface area on the sensitivity in micro- and nanostructured autonomously reporting sensing hydrogel materials for the detection of bacterial enzymes. The colorimetric sensing materials for the detection of β-glucuronidase (ß-GUS) from Escherichia coli (E. coli) were fabricated by template replication of crosslinked pullulan acetoacetate (PUAA) and by electrospinning chitosan/polyethylene oxide nanofibers (CS/PEO NFs), both equipped with the chromogenic substrate 5-bromo-4-chloro-3-indolyl-β-D-glucuronide. The investigation of the dependence of the initial reaction rates on surface area unveiled a linear relationship of rate and thereby time to observe a signal for a given concentration of bacterial enzyme. This knowledge was exploited in nanoscale sensing materials made of CS/PEO NFs with diameters of 295 ± 100 nm. Compared to bulk hydrogel slabs, the rate of hydrolysis was significantly enhanced in NFs when exposed to bacteria suspension cultures and thus ensuring a rapid detection of living E. coli that produces the enzyme β-GUS. The findings afford generalized design principles for the improvement of known and novel sensing materials towards rapid detection of bacteria by nanostructuring in medical and food related settings.

Evanescent Wave-Guided Growth of an Organic Supramolecular Nanowire Array

The ordered assembly of molecules within a specific space of nanoscale, such as a surface, holds great promise in advanced micro-/nanostructure fabrication for various applications. Herein, we demonstrate the evanescent wave (EW)-guided organization of small molecules into a long-range ordered nanowire (NW) array. Experiment and simulation revealed that the orientation and periodicity of the NW array were feasibly regulated by altering the propagation direction and the wavelength of EW. The generality of this approach was demonstrated by using different molecule precursors. While existing studies on EW often took advantages of its near-field property for optical sensing, this work demonstrated the photochemical power of EW in the guided-assembly of small molecules for the first time. It also provides an enlightening avenue to periodic structure with fluorescence, promising for super-resolution microscopy and important devices applicable to optical and bio-related fields.