Simultaneous enhanced antibiotic pollutants removal and sustained permeability of the membrane involving CoFe2O4/MoS2 catalyst initiated with simple H2O2 backwashing

Membranes for wastewater treatment should ideally exhibit sustainable high permeate production, enhanced pollutant removal, and intrinsic physical rejection. In this study, CoFe2O4/MoS2 serves as a non-homogeneous phase catalyst; it is combined with polyether sulfone membranes via liquid-induced phase separation to simultaneously sustain membrane permeability and enhance antibiotic pollutant degradation. The prepared catalytic membranes have higher pure water flux (329.34 L m-2 h-1) than pristine polyethersulfone membranes (219.03 L m-2 h-1), as well as higher mean pore size, porosity, and hydrophilicity. Under a moderate transmembrane pressure (0.05 MPa), tetracycline (TC) in synthetic and real wastewater was degraded by the optimal catalytic membrane by 72.7 % and 91.2 %, respectively. Owing to the generation of the reactive oxygen species (ROS) during the Fenton-like reaction process, the catalytic membrane could exclude the natural organics during the H2O2 backwash step and selectively promote fouling degradation in the membrane channel. The irreversible fouling ratio of the catalyzed membrane was significantly reduced, and the flux recovery rate increased by up to 91.6 %. A potential catalytic mechanism and TC degradation pathways were proposed. This study offers valuable insights for designing catalytic membranes with enhanced filtration performance.

Slow-release synthesis of Cu single-atom catalysts with the optimized geometric structure and density of state distribution for Fenton-like catalysis

Single-atom Fenton-like catalysis has attracted significant attention, yet the quest for controllable synthesis of single-atom catalysts (SACs) with modulation of electron configuration is driven by the current disadvantages of poor activity, low selectivity, narrow pH range, and ambiguous structure-performance relationship. Herein, we devised an innovative strategy, the slow-release synthesis, to fabricate superior Cu SACs by facilitating the dynamic equilibrium between metal precursor supply and anchoring site formation. In this strategy, the dynamics of anchoring site formation, metal precursor release, and their binding reaction kinetics were regulated. Bolstered by harmoniously aligned dynamics, the selective and specific monatomic binding reactions were ensured to refine controllable SACs synthesis with well-defined structure-reactivity relationship. A copious quantity of monatomic dispersed metal became deposited on the C3N4/montmorillonite (MMT) interface and surface with accessible exposure due to the convenient mass transfer within ordered MMT. The slow-release effect facilitated the generation of targeted high-quality sites by equilibrating the supply and demand of the metal precursor and anchoring site and improved the utilization ratio of metal precursors. An excellent Fenton-like reactivity for contaminant degradation was achieved by the Cu1/C3N4/MMT with diminished toxic Cu liberation. Also, the selective ·OH-mediated reaction mechanism was elucidated. Our findings provide a strategy for regulating the intractable anchoring events and optimizing the microenvironment of the monatomic metal center to synthesize superior SACs.

Atomic coordination structural dynamic evolution of single-atom Mo catalyst for promoting H2 activation in slurry phase hydrocracking

Development of efficient catalysts with high atomic utilization and turnover frequency (TOF) for H₂ activation in slurry phase hydrocracking (SPHC) is crucial for the conversion of vacuum residue (VR). Herein, for the first time, we reported a robust and stable single atoms (SAs) Mo catalyst through a polymerization-pyrolysis-in situ sulfurization strategy for activating H₂ in SPHC of VR. An interesting atomic coordination structural dynamic evolution of Mo active sites was discovered. During hydrocracking of VR, the O atoms that coordinated with Mo were gradually replaced by S atoms, which led to the O/S exchange process. The coordination structure of the Mo SAs changed from pre-reaction Mo-O₃S₁ to post-reaction Mo-O₁S₃ coordination configurations, promoting the efficient homolytic cleavage activation of H₂ into H radical species effectively. The evolved Mo SAs catalyst exhibited robust catalytic hydrogenation activity with the per pass conversion of VR of 65 wt%, product yield of liquid oils of 93 wt%, coke content of only 0.63 wt%, TOF calculated for total metals up to 0.35 s^-1, and good cyclic stability. Theoretical calculation reveals that the significant variation of occupied Mo 4d states before and after H₂ interaction has a direct bearing on the dynamic evolution of Mo SAs catalyst structure. The lower d-band center of Mo-O₁S₃ site indicates that atomic H diffusion is easy, which is conducive to catalytic hydrogenation. The finding of this study is of great significance to the development of high atom economy catalysts for the industrial application of heavy oil upgrading technology.

A novel Fe/Mo co-catalyzed graphene-based nanocomposite to activate peroxymonosulfate for highly efficient degradation of organic pollutants

A novel 3D α-FeOOH@MoS₂/rGO nanocomposite was successfully fabricated by a simple in situ hydrothermal method. It is a highly efficient heterogeneous catalyst in activation of peroxymonosulfate (PMS) for rapid degradation of rhodamine B (RhB), with 99.9% of RhB removed within 20 min. The introduction of rGO contributes to uniform dispersion and sufficient contact of α-FeOOH and MoS₂ nanosheets. Highly active Mo(IV) enhances the reduction of Fe(III), improves Fe(III)/Fe(II) conversion and promotes the generation of O₂1, which ensures an improved catalytic activity. MoS₂/rGO hybrid can effectively solve the problem of material reunion and make α-FeOOH exhibit excellent catalytic performance. The α-FeOOH@MoS₂-rGO/PMS system is a co-catalytic system based on the active components of α-FeOOH and MoS₂. The main reactive oxygen species in the α-FeOOH@MoS₂-rGO/PMS system are O₂1, SO₄^.- and ⋅O₂^-, which contribute to a high reactivity over a wide range of pH (5-9). Besides, this system is highly resistant to anions (Cl^-, SO₄^2-) and natural organic matter (humic acid), and can be widely used for degradation of common organic pollutants. The α-FeOOH@MoS₂/rGO is a promising Fenton-like catalyst for refractory organic wastewater treatment.

Photocatalytic degradation of paracetamol and bisphenol A by chitosan supported covalent organic framework thin film with visible light irradiation

Covalent Organic Frameworks (COFs) have attracted extensive attention for the photocatalytic degradation of emerging organic contaminants. The difficulty in separation and recovery after use yet would hinder the practical application of COFs in powder form. In present study, COFs in film form were fabricated via using chitosan as the film-substrate to support COFs (CSCF). We found that CSCF could effectively degrade two types of emerging organic contaminants under visible light irradiation. Particularly, CSCF could effectively degrade 99.8% of paracetamol (PCT) and 94.0% of bisphenol A (BPA) within 180 min under visible light irradiation. •O₂^- and h⁺ played dominant roles during the photocatalytic degradation process. Hydroxylation and cleavage were the main degradation processes. CSCF exhibited good photocatalytic degradation performance in a broad range of ionic strengths, in the presence of common coexisting ions including Cl^-, NO₃^- and SO₄^2-, in a wide range of pH (5-11), and in real water samples including tap water, river water and lake water. Moreover, CSCF could be easily collected after use and exhibited excellent degradation performance in five successive cycles. CSCF has potential applications to treat water with either PCT or BPA contamination. This study provided a new insight into the practical application of COFs.

Overturned Loading of Inert CeO2 to Active Co3 O4 for Unusually Improved Catalytic Activity in Fenton-Like Reactions

In the past decades, numerous efforts have been devoted to improving the catalytic activity of nanocomposites by either exposing more active sites or regulating the interaction between the support and nanoparticles while keeping the structure of the active sites unchanged. Here, we report the fabrication of a Co₃ O₄ -CeO₂ nanocomposite via overturning the loading direction, i.e., loading an inert CeO₂ support onto active Co₃ O₄ nanoparticles. The resultant catalyst exhibits unexpectedly higher activity and stability in peroxymonosulfate-based Fenton-like reactions than its analog prepared by the traditional impregnation method. Abundant oxygen vacancies (O_v with a Co⋅⋅⋅O_v ⋅⋅⋅Ce structure instead of Co⋅⋅⋅O_v ) are generated as new active sites to facilitate the cleavage of the peroxide bond to produce SO₄ ^.- and accelerate the rate-limiting step, i.e., the desorption of SO₄ ^.- , affording improved activity. This strategy is a new direction for boosting the catalytic activity of nanocomposite catalysts in various scenarios, including environmental remediation and energy applications.

The construction of a palladium–hydrogen accelerated catalytic Fenton system enhanced by UiO-66(Zr)

The introduction of H2 and Pd/UiO-66(Zr) accelerated the FeII/FeIII cycle and led to higher contaminant degradation using only a trace level of FeII in several reaction cycles.

Green Synthesis of Nano-Zero-Valent Iron Using Ricinus Communis Seeds Extract: Characterization and Application in the Treatment of Methylene Blue-Polluted Water

In this study, the removal of methylene blue dye (MB) from aqueous solution was examined using a novel green adsorbent to overcome the obstacles encountered in chemical methods. Ricinus communis (RC) aqueous seeds extract was herein used as a reducing and capping agent to synthesize a novel nano-zero-valent iron (RC-nZVI) for the adsorption of harmful MB. Structural and morphological characterization of the synthesized RC-nZVI were performed using several techniques, e.g., steady-state absorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and zeta potential. The maximum efficiency of the removal was 96.8% at pH 6 and 25 °C. According to the kinetics study results, the adsorption process obeys the pseudo-first-order model. The experimental equilibrium data were fitted to the Freundlich isotherm model, the maximum adsorption capacity reached was 61.37 mg·g-1, and the equilibrium parameters were determined. The synthesized RC-nZVI possesses good reusability and can be considered as a potential economic and environmentally friendly adsorbent.

Carbon Nitride Supported High-Loading Fe Single-Atom Catalyst for Activating of Peroxymonosulfate to Generate 1 O2 with 100 % Selectivity

Singlet oxygen (¹ O₂ ) is an excellent active species for the selective degradation of organic pollutions. However, it is difficult to achieve high efficiency and selectivity for the generation of ¹ O₂ . In this work, we develop a graphitic carbon nitride supported Fe single-atoms catalyst (Fe₁ /CN) containing highly uniform Fe-N₄ active sites with a high Fe loading of 11.2 wt %. The Fe₁ /CN achieves generation of 100 % ¹ O₂ by activating peroxymonosulfate (PMS), which shows an ultrahigh p-chlorophenol degradation efficiency. Density functional theory calculations results demonstrate that in contrast to Co and Ni single-atom sites, the Fe-N₄ sites in Fe₁ /CN adsorb the terminal O of PMS, which can facilitate the oxidization of PMS to form SO₅ ^.- , and thereafter efficiently generate ¹ O₂ with 100 % selectivity. In addition, the Fe₁ /CN exhibits strong resistance to inorganic ions, natural organic matter, and pH value during the degradation of organic pollutants in the presence of PMS. This work develops a novel catalyst for the 100 % selective production of ¹ O₂ for highly selective and efficient degradation of pollutants.