Mussel-Inspired Surface-Imprinted Sensors for Potentiometric Label-Free Detection of Biological Species

A New Discovery on the Potential Stability of Ion-Selective Membranes: The Poison from Tetrahydrofuran

Ion-selective electrodes (ISEs) have widespread use in the fields of clinical and environmental analyses. Tetrahydrofuran (THF) is the most used solvent for the preparation of modern ISEs, equipped with ion-selective membranes (ISMs). Until now, the influence of impurities in THF toward potentiometric instability of ion-selective membrane based ISEs was probably associated with the presence of either residual water or peroxide. To address this issue, most literature recommends redistilling THF prior to use in the preparation of the potentiometric membranes. Current study reveals that the actual THF impurity that is responsible for potential instability in the ISM includes products from the oxidation of THF, which contains the hydroxyl group and possibly carbonyl group with a boiling point of above 200 °C. The density functional theory calculation supported pathway of the chemical reaction of THF oxidation, hence, the chemical structure of the uncertain impurities was predicted. The underlying reason for the deteriorating potential stability of the ISEs is proposed as the significant hydrophilicity of these impurities that affect the partitioning of the ion sensing components in the membrane, thus enhancing the leaching of the membrane components from the membrane phase. This finding explains why redistillation of aged THF is advised.

Sensors Based on Molecularly Imprinted Polymers in the Field of Cancer Biomarker Detection: A Review

Biomarkers play a pivotal role in the screening, diagnosis, prevention, and post-treatment follow-up of various malignant tumors. In certain instances, identifying these markers necessitates prior treatment due to the complex nature of the tumor microenvironment. Consequently, advancing techniques that exhibit selectivity, specificity, and enable streamlined analysis hold significant importance. Molecularly imprinted polymers (MIPs) are considered synthetic antibodies because they possess the property of molecular recognition with high selectivity and sensitivity. In recent years, there has been a notable surge in the investigation of these materials, primarily driven by their remarkable adaptability in terms of tailoring them for specific target molecules and integrating them into diverse analytical technologies. This review presents a comprehensive analysis of molecular imprinting techniques, highlighting their application in developing sensors and analytical methods for cancer detection, diagnosis, and monitoring. Therefore, MIPs offer great potential in oncology and show promise for improving the accuracy of cancer screening and diagnosis procedures.

Chronopotentiometric Nanopore Sensor Based on a Stimulus-Responsive Molecularly Imprinted Polymer for Label-Free Dual-Biomarker Detection

The development of sensors for detection of biomarkers exhibits an exciting potential in diagnosis of diseases. Herein, we propose a novel electrochemical sensing strategy for label-free dual-biomarker detection, which is based on the combination of stimulus-responsive molecularly imprinted polymer (MIP)-modified nanopores and a polymeric membrane chronopotentiometric sensor. The ion fluxes galvanostatically imposed on the sensing membrane surface can be blocked by the recognition reaction between the target biomarker in the sample solution and the stimulus-responsive MIP receptor in the nanopores, thus causing a potential change. By using two external stimuli (i.e., pH and temperature), the recognition abilities of the stimulus-responsive MIP receptor can be effectively modulated so that dual-biomarker label-free chronopotentiometric detection can be achieved. Using alpha fetoprotein (AFP) and prostate-specific antigen (PSA) as model biomarkers, the proposed sensor offers detection limits of 0.17 and 0.42 ng/mL for AFP and PSA, respectively.

Improvement of the selectivity of a molecularly imprinted polymer-based potentiometric sensor by using a specific functional monomer

Potentiometric sensors based on the molecularly imprinted polymers (MIPs) as the receptors have been successfully developed for determination of various organic and biological species. However, these MIP receptors may suffer from problems of low selectivity. Especially, it would be difficult to distinguish the target analyte from its structurally similar interferents. In this work, we propose a novel strategy that using specific functional monomer to fabricate MIP with high selectivity towards the target molecule. The density functional theory calculations are used to investigate the interactions between the template and the functional monomer. The binding energy between the template and functional monomer can be used as the criterion for identifying the optimal monomer. As a proof-of-concept experiment, bisphenol A (BPA) is chosen as the template and the MIP is synthesized by the precipitation polymerization method using the specific allyl-β-cyclodextrin (allyl-β-CD) with high affinity towards BPA as the functional monomer. The high-affinity MIP is employed as the receptor for the construction of the potentiometric sensor. The proposed potentiometric sensor based on the MIP using allyl-β-CD as the functional monomer shows an improved response performance in terms of selectivity and sensitivity compared to the conventional potentiometric sensor based on the MIP with the common monomer (i.e., methacrylic acid). This allyl-β-CD MIP-based potentiometric sensor shows a detection limit of 0.29 μM for BPA, which is about one order of magnitude lower than that obtained by the conventional MIP-based potentiometric sensor. We believe that utilizing a functional monomer with specific recognition ability towards target in the fabrication of MIP could provide an appealing way to construct highly selective MIP-based electrochemical and optical sensors.

Modern Potentiometric Biosensing Based on Non-Equilibrium Measurement Techniques

Modern potentiometric sensors based on polymeric membrane ion-selective electrodes (ISEs) have achieved new breakthroughs in sensitivity, selectivity, and stability and have extended applications in environmental surveillance, medical diagnostics, and industrial analysis. Moreover, nonclassical potentiometry shows promise for many applications and opens up new opportunities for potentiometric biosensing. Here, we aim to provide a concept to summarize advances over the past decade in the development of potentiometric biosensors with polymeric membrane ISEs. This Concept article articulates sensing mechanisms based on non-equilibrium measurement techniques. In particular, we emphasize new trends in potentiometric biosensing based on attractive dynamic approaches. Representative examples are selected to illustrate key applications under zero-current conditions and stimulus-controlled modes. More importantly, fruitful information obtained from non-equilibrium measurements with dynamic responses can be useful for artificial intelligence (AI). The combination of ISEs with advanced AI techniques for effective data processing is also discussed. We hope that this Concept will illustrate the great possibilities offered by non-equilibrium measurement techniques and AI in potentiometric biosensing and encourage further innovations in this exciting field.

Bovine Serum Albumin Molecularly Imprinted Electrochemical Sensors Modified by Carboxylated Multi-Walled Carbon Nanotubes/CaAlg Hydrogels

In this paper, sodium alginate (NaAlg) was used as functional monomers, bovine serum albumin (BSA) was used as template molecules, and calcium chloride (CaCl2) aqueous solution was used as a cross-linking agent to prepare BSA molecularly imprinted carboxylated multi-wall carbon nanotubes (CMWCNT)/CaAlg hydrogel films (MIPs) and non-imprinted hydrogel films (NIPs). The adsorption capacity of the MIP film for BSA was 27.23 mg/g and the imprinting efficiency was 2.73. The MIP and NIP hydrogel film were loaded on the surface of the printed electrode, and electrochemical performance tests were carried out by electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV) using the electrochemical workstation. The loaded MIP film and NIP film effectively improved the electrochemical signal of the bare carbon electrode. When the pH value of the Tris HCl elution solution was 7.4, the elution time was 15 min and the adsorption time was 15 min, and the peak currents of MIP-modified electrodes and NIP-modified electrodes reached their maximum values. There was a specific interaction between MIP-modified electrodes and BSA, exhibiting specific recognition for BSA. In addition, the MIP-modified electrodes had good anti-interference, reusability, stability, and reproducibility. The detection limit (LOD) was 5.6 × 10-6 mg mL-1.

Ultrasensitive Determination of Trypsin in Human Urine Based on Amplified Fluorescence Response

The determination of trypsin activity in human urine is important for evaluating pancreatic disease. We designed an effective fluorescence sensing strategy based on a self-assembled amphiphilic pyrene/protamine complex system that provides an amplified fluorescence response for highly sensitive and selective detection of trypsin. In aqueous solution, the functionalized pyrene formed fluorescent, π-extended aggregates inside micelles, which were effectively quenched by protamine (a trypsin substrate). However, this quenched fluorescence was very sensitively recovered by the trypsin's enzymatic reaction, and this was attributed to a marked reduction in enhanced exciton migration caused by protamine in π-delocalized pyrene aggregates. The devised sensing platform was successfully utilized to selectively and sensitively detect trypsin at very low concentrations (0.03-0.5 μg mL^-1) in non-pretreated human urine and to screen for trypsin inhibitors at concentrations of 0.1-5.0 μg mL^-1.

Fabrication of high-performance cell-imprinted polymers based on AuNPs/MXene composites via metal-free visible light-induced ATRP

Cell-imprinted polymers (CIPs) for yeasts were fabricated via metal-free visible-light-induced atom transfer radical polymerization (MVL ATRP) on the surface of a glassy carbon electrode (GCE) which had been modified with gold nanoparticles (AuNPs)/MXene (Ti₃C₂T_x) composites. Here, the AuNPs/Ti₃C₂T_x composites form a macroporous structure, which could improve the electron transfer rate of the materials and facilitate the leaving or rebinding of cells. Methacrylic acid (MAA) and N,N'-methylene bis-acrylamide (MBA) were selected as the functional monomer and cross-linker of CIPs, because they could form efficient hydrogen bonding with mannan from yeast cell walls. The obtained electrode (CIPs/AuNPs/Ti₃C₂T_x/GCE) was characterized by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Further experiments indicated that the CIPs/AuNPs/Ti₃C₂T_x/GCE electrode could be utilized as an electrochemical biosensor to determine yeast cells by differential pulse voltammetry (DPV). The linear response range was 1.0 × 10² to 1.0 × 10⁹ cells per mL and the detection limit was 20 cells per mL (S/N = 3). The CIPs/AuNPs/Ti₃C₂T_x/GCE electrode also showed good selectivity, repeatability, reproducibility, and regeneration. Finally, the proposed sensor was used to detect yeast cells in commercial samples of Saccharomyces boulardii sachets by a standard addition method. The obtained recovery was from 96.9 to 104.8% showing its potential applications in clinical and diagnostic research.

Potentiometric sensor based on a computationally designed molecularly imprinted receptor

Molecularly imprinted polymer (MIP)-based polymeric membrane potentiometric sensors are ideal candidates for detection of organic species. The development of such sensors has opened new attractive horizons for potentiometric sensing. However, it should be noted that in the preparation of these MIP receptors, the selection of the functional monomer usually depends on empirical trial- and error-based optimization, which involves tedious and time-consuming experiments. In this work, the computer-aided design and synthesis of an MIP receptor are applied in the fabrication of an MIP-based potentiometric sensor. The density functional theory calculation with the B3LYP model and 6-31G(d) basis set is used to study the interactions between the functional monomer and template molecules. The binding energies of the complexations between the template molecule and different functional monomers are used as a criterion for the selection of the proper monomer. The designed MIP is then synthesized and employed as the receptor for the fabrication of the potentiometric sensor. As a proof-of-concept experiment, the antibiotic sulfadiazine has been selected as a model and 4 functional monomers, 2-hydroxyethyl methacrylate, methyl methacrylate, N-isopropylacrylamide and N-phenylacrylamide, have been chosen. The designed MIP-based sensor exhibits excellent sensitivity with a linear range of 1-10 μM and also shows a good selectivity. We believe that the proposed computer-aided synthesis technique for the MIP receptor selection can provide a general and facile way to replace the traditional empirical MIP preparation method in the fabrication of MIP-based electrochemical and optical sensors.

Deep Learning-Enhanced Potentiometric Aptasensing with Magneto-Controlled Sensors

Bioelectronic sensors that report charge changes of a biomolecule upon target binding enable direct and sensitive analyte detection but remain a major challenge for potentiometric measurement, mainly due to Debye Length limitations and the need for molecular-level platforms. Here, we report on a magneto-controlled potentiometric method to directly and sensitively measure the target-binding induced charge change of DNA aptamers assembled on magnetic beads using a polymeric membrane potentiometric ion sensor. The potentiometric responses of the negatively charged aptamer, serving as a receptor and reporter, were dynamically controlled and modulated by applying a magnetic field. Based on a potentiometric array, this non-equilibrium measurement technique combined with deep learning algorithms allows for rapidly and reliably classifying and quantifying diverse small molecules using antibiotics as models. This potentiometric strategy opens new modalities for sensing applications.

Greenificated Molecularly Imprinted Materials for Advanced Applications

Molecular imprinting technology (MIT) produces artificial binding sites with precise complementarity to substrates and thereby is capable of exquisite molecular recognition. Over five decades of evolution, it is predicted that the resulting host imprinted materials will overtake natural receptors for research and application purposes, but in practice, this has not yet been realized due to the unsustainability of their life cycles (i.e., precursors, creation, use, recycling, and end-of-life). To address this issue, greenificated molecularly imprinted polymers (GMIPs) are a new class of plastic antibodies that have approached sustainability by following one or more of the greenification principles, while also demonstrating more far-reaching applications compared to their natural counterparts. In this review, the most recent developments in the delicate design and advanced application of GMIPs in six fast-growing and emerging fields are surveyed, namely biomedicine/therapy, catalysis, energy harvesting/storage, nanoparticle detection, gas sensing/adsorption, and environmental remediation. In addition, their distinct features are highlighted, and the optimal means to utilize these features for attaining incredibly far-reaching applications are discussed. Importantly, the obscure technical challenges of the greenificated MIT are revealed, and conceivable solutions are offered. Lastly, several perspectives on future research directions are proposed.

Potentiometric Biosensor Based on Artificial Antibodies for an Alzheimer Biomarker Detection

This paper presents a potentiometric biosensor for the detection of amyloid β-42 (Aβ-42) in point-of-care analysis. This approach is based on the molecular imprint polymer (MIP) technique, which uses covalently immobilised Aβ-42 to create specific detection cavities on the surface of single-walled carbon nanotubes (SWCNTs). The biosensor was prepared by binding Aβ-42 to the SWCNT surface and then imprinting it by adding acrylamide (monomer), N,N’-methylene-bis-acrylamide (crosslinker) and ammonium persulphate (initiator). The target peptide was removed from the polymer matrix by the proteolytic action of an enzyme (proteinase K). The presence of imprinting sites was confirmed by comparing a MIP-modified surface with a negative control (NIP) consisting of a similar material where the target molecule had been removed from the process. The ability of the sensing material to rebind Aβ-42 was demonstrated by incorporating the MIP material as an electroactive compound in a PVC/plasticiser mixture applied to a solid conductive support of graphite. All steps of the synthesis of the imprinted materials were followed by Raman spectroscopy and Fourier transform infrared spectroscopy (FTIR). The analytical performance was evaluated by potentiometric transduction, and the MIP material showed cationic slopes of 75 mV-decade−1 in buffer pH 8.0 and a detection limit of 0.72 μg/mL. Overall, potentiometric transduction confirmed that the sensor can discriminate Aβ-42 in the presence of other biomolecules in the same solution.

Towards potentiometric detection in nonaqueous media: Evaluation of the impacts of organic solvents on polymeric membrane ion-selective electrodes

Polymeric membrane ion-selective electrodes (ISEs) have been widely used in various fields including clinical diagnosis, environmental monitoring and industrial analysis. Although most samples of analytical interest measured by the ISEs are aqueous solutions, the applications of these electrodes in nonaqueous media are often inevitable. Unfortunately, so far, little has been known about the extent to which the properties of the ISEs could be affected by the organic solvents. Herein, the feasibility for the applications of the polymeric membrane ISEs in nonaqueous media has been investigated. A polymeric membrane Ca²⁺-ISE is chosen as a model of potentiometric sensors. Four typical water miscible organic solvents (three protic solvents: ethanol, acetic acid, and methanol, and one aprotic dipolar solvent: acetonitrile) are used as the representative examples. Experiments show that the aprotic solvent acetonitrile has the strongest destructive ability towards the sensing performance of the ISE in terms of Nernstian slope and selectivity coefficient. Moreover, the effect on the sensing performance depends on the kind of the protic solvent, the immersion time and the polarity of the membrane plasticizer. We believe that the obtained results could promote further applications of the polymeric membrane ISEs in the organic solvent-containing samples, which could significantly extend the application scope of the ISEs.

Solid-Contact Potentiometric Anion Sensing Based on Classic Silver/Silver Insoluble Salts Electrodes without Ion-Selective Membrane

Current solid potentiometric ion sensors mostly rely on polymeric-membrane-based, solid-contact, ion-selective electrodes (SC-ISEs). However, anion sensing has been a challenge with respect to cations due to the rareness of anion ionophores. Classic metal/metal insoluble salt electrodes (such as Ag/AgCl) without an ion-selective membrane (ISM) offer an alternative. In this work, we first compared the two types of SC-ISEs of Cl- with/without the ISM. It is found that the ISM-free Ag/AgCl electrode discloses a comparable selectivity regarding organic chloride ionophores. Additionally, the electrode exhibits better comprehensive performances (stability, reproducibility, and anti-interference ability) than the ISM-based SC-ISE. In addition to Cl-, other Ag/AgX electrodes also work toward single and multi-valent anions sensing. Finally, a flexible Cl- sensor was fabricated for on-body monitoring the concentration of sweat Cl- to illustrate a proof-of-concept application in wearable anion sensors. This work re-emphasizes the ISM-free SC-ISEs for solid anion sensing.

Molecular Imprinting: Green Perspectives and Strategies

Advances in revolutionary technologies pose new challenges for human life; in response to them, global responsibility is pushing modern technologies toward greener pathways. Molecular imprinting technology (MIT) is a multidisciplinary mimic technology simulating the specific binding principle of enzymes to substrates or antigens to antibodies; along with its rapid progress and wide applications, MIT faces the challenge of complying with green sustainable development requirements. With the identification of environmental risks associated with unsustainable MIT, a new aspect of MIT, termed green MIT, has emerged and developed. However, so far, no clear definition has been provided to appraise green MIT. Herein, the implementation process of green chemistry in MIT is demonstrated and a mnemonic device in the form of an acronym, GREENIFICATION, is proposed to present the green MIT principles. The entire greenificated imprinting process is surveyed, including element choice, polymerization implementation, energy input, imprinting strategies, waste treatment, and recovery, as well as the impacts of these processes on operator health and the environment. Moreover, assistance of upgraded instrumentation in deploying greener goals is considered. Finally, future perspectives are presented to provide a more complete picture of the greenificated MIT road map and to pave the way for further development.

Solid-Contact Ion Sensing Without Using an Ion-Selective Membrane through Classic Li-Ion Battery Materials

The solid-contact ion-selective electrodes (SC-ISEs) are a type of potentiometric analytical device with features of rapid response, online analysis, and miniaturization. The state-of-the-art SC-ISEs are composed of a solid-contact (SC) layer and an ion-selective membrane (ISM) layer with respective functions of ion-to-electron transduction and ion recognition. Two challenges for the SC-ISEs are the water-layer formation at the SC/ISM phase boundary and the leaking of ISM components, which are both originated from the ISM. Herein, we report a type of SC-ISE based on classic Li-ion battery materials as the SC layer without using the ISM for potentiometric lithium-ion sensing. Both LiFePO₄- and LiMn₂O₄-based SC-ISEs display good Li⁺ sensing properties (sensitivity, selectivity, and stability). The proposed LiFePO₄ electrode exhibits comparable sensitivity and a linear range to conventional SC-ISEs with ISM. Owing to the nonexistence of ISM, the LiFePO₄ electrode displays high potential stability. Besides, the LiMn₂O₄ electrode shows a Nernstian response toward Li⁺ sensing in a human blood serum solution. This work emphasizes the concept of non-ISM-based SC-ISEs for potentiometric ion sensing.

Stimuli-responsive surfaces for switchable wettability and adhesion

Diverse unique surfaces exist in nature, e.g. lotus leaf, rose petal and rice leaf. They show similar contact angles but different adhesion properties. According to the different wettability and adhesion characteristics, this review reclassifies different contact states of droplets on surfaces. Inspired by the biological surfaces, smart artificial surfaces have been developed which respond to external stimuli and consequently switch between different states. Responsive surfaces driven by various stimuli, e.g. stretching, magnetic, photo, electric, temperature, humidity and pH, are discussed. Studies reporting on either atmospheric or underwater environments are discussed. The application of tailoring surface wettability and adhesion includes microfluidics/droplet manipulation, liquid transport and harvesting, water energy harvesting and flexible smart devices. Particular attention is placed on the horizontal comparison of smart surfaces with the same stimuli. Finally, the current challenges and future prospects in this field are also identified.

Facile imprinted polymer for label-free highly selective potentiometric sensing of proteins: case of recombinant human erythropoietin

In the current study, a molecularly imprinted polymer (MIP)-based potentiometric sensor was fabricated for a label-free determination of recombinant human erythropoietin (rhEPO). The MIP sensor was operated under zero current conditions using tetra-butyl ammonium bromide as a marker ion. A highly ordered rhEPO surface imprinted layer was prepared using 3-aminopropyl triethoxysilane and tetraethoxysilane as a monomer and cross-linker, respectively, under mild reaction conditions. A two-fold increase in the signal output was obtained by polymeric surface minimization (0.5 mm) that allowed more pronounced molecular recognition (imprinting factor = 20.1). The proportion of cross-reactivity was examined using different interfering biomolecules. Results confirmed sensor specificity for both structurally related and unrelated proteins. An ~40% decrease in the response was obtained for rhEPO-β compared to rhEPO-α. The imprinted polymeric surface was evaluated using scanning electron microscopy and Fourier transform infrared spectroscopy. Under the optimal measurement conditions, a linear range of 10.00-1000.00 ng mL^-1 (10^-10 - 10^-8 M) was obtained. The sensor was employed for the determination of rhEPO in different biopharmaceutical formulations. Results were validated against standard immunoassay. Spiked human serum samples were analyzed and the assay was validated. The presence of non-specific proteins did not significantly affect (~8%) the results of our assay. A concentration-dependent linear response was produced in an identical range with detection limit as low as 6.50 ng mL^-1 (2.14 × 10^-10 M). The facile fabricated MIP sensor offers a cost-effective, portable, and easy to use alternative for biosimilarity assessment and clinical application.

A molecularly imprinted polymer-based potentiometric sensor based on covalent recognition for the determination of dopamine

Polymeric membrane potentiometric sensors based on molecularly imprinted polymers (MIPs) have been successfully designed for the detection of organic compounds both in ionic and neutral forms. However, most of these sensors are based on the non-covalent recognition interactions between the functional groups of the MIP in the polymeric sensing membrane and the target. These weak non-covalent interactions are unfavorable for the detection of hydrophilic organic compounds (e.g., dopamine). Herein novel MIP potentiometric sensor based covalent recognition for the determination of protonated dopamine is described. Uniform-sized boronate-based MIP beads are utilized as the recognition receptors. These receptors can covalently bind with dopamine with a cis-diol group to form a five-membered cyclic ester and thus provide a higher affinity because of the stronger nature of the covalent bonds. It has been found that the proposed electrode shows an excellent sensitivity towards dopamine with a detection limit of 2.1 μM, which could satisfy the needs for in vivo analysis of dopamine in the brain of living animals. We believe that the covalent recognition MIP-based sensing strategy provides an appealing way to design MIP-based electrochemical and optical sensors with excellent sensing properties.

Thin polymeric membrane ion-selective electrodes for trace-level potentiometric detection

In this work, we describe a novel method to improve the detection limits of the non-classical polymeric membrane ion-selective electrodes (ISEs) which are conditioned with highly discriminated ions instead of primary ions. It is based on a thin-layer ISE membrane with a thickness of 5 μm, which is coated on ordered mesoporous carbon used as solid contact. The diffusion of the primary ion from the surface of the sensing membrane to the bulk of the membrane could be avoided by the proposed thin membrane configuration. Since the detection sensitivity of the non-classical ISEs depends on the accumulation of the primary ion in the interfacial layer of the sensing membrane, a lower detection limit can be obtained. By using the copper ion as a model, the present potentiometric sensor shows a significantly improved detection sensitivity compared to the conventional ISE with a membrane thickness of ca. 200 μm. Low detection limits of 0.29 and 0.53 nM can be obtained in 0.01 and 0.5 M NaCl, respectively. In addition, the proposed sensor exhibits an excellent reversibility by using a neutral proton-selective ionophore incorporated in the thin membrane.

Chronopotentiometric aptasensing with signal amplification based on enzyme-catalyzed surface polymerization

A signal amplification strategy based on the horseradish peroxidase catalyzed polymerization of dopamine on a polymeric ion-selective membrane surface is proposed for the sensitive chronopotentiometric detection of an aptamer-target binding event.

Potentiometric detection of glucose based on oligomerization with a diboronic acid using polycation as an indicator

A novel potentiometric sensor for d-glucose (Glu) using 4,4'-biphenyldiboronic acid as a receptor and polyion (poly-N-(3-aminopropyl)methacrylamide, PAPMA) as an indicator is described. The diboronic acid condenses with Glu via its two cis-diol units to form cyclic or linear oligomeric polyanions which can interact electrostatically with PAPMA, thus efficiently decreasing its potentiometric response on a polycation-sensitive membrane electrode. Although d-fructose (Fru), d-galactose (Gal) and d-mannose (Man) show even higher binding affinities to the diboronic acid as compared to Glu, these monosaccharides with only one cis-diol unit cannot oligomerize with the receptor, which efficiently excludes the interferences from the Glu's stereoisomers. The results obtained from blood sample analysis indicate that the proposed sensor is promising for detection of Glu in real-world applications.

Plasticizer-free polymer membrane potentiometric sensors based on molecularly imprinted polymers for determination of neutral phenols

Polymeric membrane potentiometric sensors based on molecularly imprinted polymers (MIPs) as the receptors have been successfully developed for detection of organic and biological species. However, it should be noted that all of the polymeric membrane matrices of these sensors developed so far are the plasticized poly(vinyl chloride) (PVC) membranes, which are usually suffered from undesired plasticizer leaching. Hence, for the first time, we describe a novel plasticizer-free MIP-based potentiometric sensor. A new copolymer, methyl methacrylate and 2-ethylhexyl acrylate (MMA-2-EHA), is synthesized and used as the sensing membrane matrix. By using neutral bisphenol A (BPA) as a model, the proposed plasticizer-free MIP sensor shows an excellent sensitivity and a good selectivity with a detection limit of 32 nM. Additionally, the proposed MMA-2-EHA-based MIP membrane exhibits lower cytotoxicity, higher hydrophobicity and better MIP dispersion ability compared to the classical plasticized PVC-based MIP sensing membrane. We believed that the new copolymer membrane-based MIP sensor can provide an appealing substitute for the traditional PVC membrane sensor in the development of polymeric membrane-based electrochemical and optical MIP sensors.

Molecularly Imprinted Synthetic Antibodies: From Chemical Design to Biomedical Applications

Billions of dollars are invested into the monoclonal antibody market every year to meet the increasing demand in clinical diagnosis and therapy. However, natural antibodies still suffer from poor stability and high cost, as well as ethical issues in animal experiments. Thus, developing antibody substitutes or mimics is a long-term goal for scientists. The molecular imprinting technique presents one of the most promising strategies for antibody mimicking. The molecularly imprinted polymers (MIPs) are also called "molecularly imprinted synthetic antibodies" (MISAs). The breakthroughs of key technologies and innovations in chemistry and material science in the last decades have led to the rapid development of MISAs, and their molecular affinity has become comparable to that of natural antibodies. Currently, MISAs are undergoing a revolutionary transformation of their applications, from initial adsorption and separation to the rising fields of biomedicine. Herein, the fundamental chemical design of MISAs is examined, and then current progress in biomedical applications is the focus. Meanwhile, the potential of MISAs as qualified substitutes or even to transcend the performance of natural antibodies is discussed from the perspective of frontier needs in biomedicines, to facilitate the rapid development of synthetic artificial antibodies.

A fabrication strategy for protein sensors based on an electroactive molecularly imprinted polymer: Cases of bovine serum albumin and trypsin sensing

A high-performance molecularly imprinted sensing platform inspired by natural recognition mechanisms was fabricated to detect protein by employing a linear electro-polymerizable molecularly imprinted polymer as macromonomer. This was achieved via the combination of a biosensor fabrication with a self-assembly imprinting technique without the use of chemical labels. An amphipathic electroactive copolymer was designed as macro-monomer to maintain structural integrity of the protein template via self-assembly, resulting in generation of a 3D construction around the protein molecule to form imprinted sites. Electro-polymerization was utilized not only to anchor imprinted sites but also to enhance electron transfer. The adaptable sensing platform was based on a strengthened recognition reaction between the MIP layer and template protein after the generation of an electroactive network. Bovine serum albumin (BSA) and trypsin were used as model proteins to investigate the method's generality, which gave broad detection ranges of 10^-14-10^-5 mg mL^-1 for BSA and 10^-13-10^-8 mg mL^-1 for trypsin. These results indicate that the proposed fabrication offers an effective and versatile strategy for protein recognition.

Integrated Electrochemical Biosensors for Detection of Waterborne Pathogens in Low-Resource Settings

More than 783 million people worldwide are currently without access to clean and safe water. Approximately 1 in 5 cases of mortality due to waterborne diseases involve children, and over 1.5 million cases of waterborne disease occur every year. In the developing world, this makes waterborne diseases the second highest cause of mortality. Such cases of waterborne disease are thought to be caused by poor sanitation, water infrastructure, public knowledge, and lack of suitable water monitoring systems. Conventional laboratory-based techniques are inadequate for effective on-site water quality monitoring purposes. This is due to their need for excessive equipment, operational complexity, lack of affordability, and long sample collection to data analysis times. In this review, we discuss the conventional techniques used in modern-day water quality testing. We discuss the future challenges of water quality testing in the developing world and how conventional techniques fall short of these challenges. Finally, we discuss the development of electrochemical biosensors and current research on the integration of these devices with microfluidic components to develop truly integrated, portable, simple to use and cost-effective devices for use by local environmental agencies, NGOs, and local communities in low-resource settings.

A novel peptide-based electrochemical biosensor for the determination of a metastasis-linked protease in pancreatic cancer cells

Proteases are involved in cancer' taking part in immune (dis)regulation, malignant progression and tumour growth. Recently, it has been found that expression levels of one of the members of the serine protease family, trypsin, is upregulated in human cancer cells of several organs, being considered as a specific cancer biomarker. Considering the great attention that electrochemical peptide sensors have nowadays, in this work, we propose a novel electroanalytical strategy for the determination of this important biomolecule. It implies the immobilization of a short synthetic peptide sequence, dually labelled with fluorescein isothiocyanate (FITC) and biotin, onto neutravidin-modified magnetic beads (MBs), followed by the peptide digestion with trypsin. Upon peptide disruption, the modified MBs were incubated with a specific fluorescein Fab fragment antibody labelled with horseradish peroxidase (HRP-antiFITC) and magnetically captured on the surface of a screen-printed carbon electrode (SPCE), where amperometric detection was performed using the hydroquinone (HQ)/HRP/H₂O₂ system. The biosensor exhibited a good reproducibility of the measurements (RSD 3.4%, n = 10), and specificity against other proteins and proteases commonly found in biological samples. This work reports the first quantitative data so far on trypsin expression in human cell lysates. The developed bioplatform was used for the direct determination of this protease in lysates from pancreatic cancer, cervix carcinoma and kidney cells in only 3 h and 30 min using low amounts (~ 0.1 μg) of raw extracts. Graphical abstract.

Label-Free Detection of Transferrin Receptor by a Designed Ligand-Protein Sensor

Advanced detection of biomarkers in biofluids plays an important role in disease diagnosis and prognosis. Current techniques with pre-labelling suffer from high cost and complicated operation, etc. Herein, we designed a label-free electrochemical biosensor for rapid detection of transferrin receptor with desirable linear range, sensitivity, specificity, reproducibility, and stability for practical applications.

Molecularly Imprinted Polymers for Cell Recognition

Since their conception 50 years ago, molecularly imprinted polymers (MIPs) have seen extensive development both in terms of synthetic routes and applications. Cells are perhaps the most challenging target for molecular imprinting. Although early work was based almost entirely around microprinting methods, recent developments have shifted towards epitope imprinting to generate MIP nanoparticles (NPs). Simultaneously, the development of techniques such as solid phase MIP synthesis has solved many historic issues of MIP production. This review briefly describes various approaches used in cell imprinting with a focus on applications of the created materials in imaging, drug delivery, diagnostics, and tissue engineering.

Electrochemical protein recognition based on macromolecular self-assembly of molecularly imprinted polymer: a new strategy to mimic antibody for label-free biosensing

A versatile strategy, based on the use of an amphiphilic copolymer as a macromonomer, was developed for the preparation of a fully synthetic MIP (molecularly imprinted polymer) sensor for protein recognition. A UV-crosslinkable copolymer poly(DMA-co-HEA-co-St) (UPDHS) was designed and synthesized to assemble with the template protein in aqueous solution, resulting in the fabrication of protein imprinted polymeric nanoparticles. Linear macromolecular chains were used to protect the structural integrity of the protein, through which a 3D structure was formed around the protein molecule to generate recognition cavities. Then the nanoparticles were immobilized on the cleaned surface of a transducer as an MIP sensing platform. The resultant MIP coating was then irradiated via ultraviolet light to ensure that the recognition cavities were stable after UV curing. After protein extraction, recognition cavities complementary to the protein molecule in shape, size and chemical functionality were formed in the platform, which could then selectively rebind to the template in a mixture of closely related compounds. The sensor exhibited satisfactory selectivity, a wide linear range from 10^-14 to 10^-9 mg mL^-1, and a comparatively lower detection limit for protein detection. This strategy offers a new and straightforward method for the synthesis of receptors for label-free and cost-efficient protein recognition. This is one of the most effective and versatile strategies for the preparation of high-performance protein recognition devices based on a fully synthetic MIP.

Label-Free Potentiometric Ion Flux Immunosensor for Determination of Recombinant Human Myelin Basic Protein: Application to Downstream Purification from Transgenic Milk

Recombinant human myelin basic protein (rhMBP) produced in the milk of transgenic cows was found exclusively associated with milk caseins. This hindered its direct determination without extensive sample pretreatment. Here, a label-free potentiometric immunosensor was developed and validated for the determination of rhMBP. An ion flux was generated under zero-current based on surface blocking of the polymeric membrane ion-selective electrode by anti-hMBP antibody and tetrabutylammonium bromide as a marker ion. The immunosensor was successfully employed in the quantitative determination of hMBP in the range of 0.10-20.00 μg/mL with a limit of detection of 50.00 ng/mL. The applicability of the passive ion flux immunosensor for determination of target analyte in complex matrices was investigated. Downstream purification of rhMBP from the milk of transgenic cows was achieved using cation exchange chromatography, immobilized metal affinity chromatography, and immunoaffinity chromatography. The specificity of the immunosensor along with matrix effect of milk proteins were demonstrated. Results obtained using the rhMBP immunosensor were further cross-validated using an orthogonal testing protocol assembled of RP-HPLC and SE-HPLC. It should be noted that the proposed ion flux immunosensor provided a feasible and specific tool for monitoring rhMBP concentration/purity, immunogenic activity, and stability. Such approach provides an attractive economic alternative to sophisticated biosensors required for in-process quality control of biopharmaceutical products.

Dual-Analyte Chronopotentiometric Aptasensing Platform Based on a G-Quadruplex/Hemin DNAzyme and Logic Gate Operations

Conventional potentiometric ion sensors that rely on a specific ion carrier in a polymeric membrane can hardly achieve multianalyte detection. Inspired by the remarkable ability of built-in logic gate sensors for multianalyte detection, herein we report a potentiometric aptasensing platform based on a G-quadruplex/hemin DNAzyme and logic gate operations for determination of two analytes using a single membrane electrode. A bifunctional probe with two aptamer units and a signal reporter oligonucleotide with a DNAzyme sequence are assembled on the magnetic beads to form a DNA hybrid structure. The "OR" and "INHIBIT" logic functions can be performed by using the two aptamers and their targets as inputs, and using the chronopotentiometric response based on the G-quadruplex/hemin DNAzyme-H₂O₂-mediated oxidation of 3,3',5,5'-tetramethylbenzidine as output. Kanamycin and oxytetracycline, as commonly used antibiotics, have been employed as the models and successfully measured.

In situ formation of gold nanoparticles in polymer inclusion membrane: Application as platform in a label-free potentiometric immunosensor for Salmonella typhimurium detection

Polymeric ion selective electrodes are highly sensitive to changes in zero current ion flow and this offers a route to signal amplification in label-free potentiometric immunosensors. In this work, a label-free potentiometric immunosensor toward Salmonella typhimurium (ST) assembled in a home-made pipette-tip electrode is described. The signal-output amplification was implemented on a gold nanoparticle polymer inclusion membrane (AuNPs-PIM) which was used as sensing platform and for antibody immobilization. Additionally, a marker ion was used to detect the antibody-antigen binding event at the electrode surface. The immunosensor construction was performed in several steps: i) gold salt ions extraction in PVC membrane; ii) AuNPs formation using Na₂EDTA as reduction agent; iii) antibody anti-Salmonella conjugation on AuNPs-PIM in pipette-tip electrodes. The potential shift observed in potentiometric measurements was derived simply from the blocking effect in the ionic flux caused by antigen-antibody conjugation, without no extra steps, mimetizing the ion-channel sensors. A detection limit of 6 cells mL^-1 was attained. As proof-of-concept, recovery studies were performed in spiked commercial apple juice samples with success. Due to the simplicity of use, the appealing cost of equipment and sensor production and being able to provide a quick analytical response (less than 1 h for a complete assay, including sample preparation for analysis), this scheme represents a good prototype device for the detection of foodborne pathogens like ST or other immune-responsive bacteria.

Internal Calibration Potentiometric Aptasensors for Simultaneous Detection of Hg2+, Cd2+, and As3+ Based on a Screen-Printed Carbon Electrodes Array

An all-solid-state potentiometric aptasensor array based on a multichannel disposable screen-printed carbon electrode (SPCE) was demonstrated for the simultaneous detection of Hg²⁺, Cd²⁺, and As³⁺ by open circuit potential (OCP) technology. The potential of the channel with an internal calibration DNA sequence (IC-DNA) was employed as the internal calibration potential (ICP) to subtract the background signal generated by the detection system, providing a built-in correction methodology. As a result, the developed aptasensor array showed high sensitivity and accuracy for detecting Hg²⁺, Cd²⁺, and As³⁺ without mutual interference or interference from other ions. The linear response ranged from 2.5 pM to 2.5 μM, and the detection limits for Hg²⁺, Cd²⁺, and As³⁺ were 2.0, 0.62, and 0.17 pM, respectively. Furthermore, the potentiometric aptasensor array was successfully applied for the simultaneous detection of three ions in real samples. The results obtained from the developed approach agreed well with the results obtained from inductively coupled plasma mass spectrometry.

Soluble Molecularly Imprinted Nanorods for Homogeneous Molecular Recognition

Nowadays, it is still difficult for molecularly imprinted polymers (MIPs) to achieve homogeneous recognition since they cannot be easily dissolved in organic or aqueous phase. To address this issue, soluble molecularly imprinted nanorods have been synthesized by using soluble polyaniline doped with a functionalized organic protonic acid as the polymer matrix. By employing 1-naphthoic acid as a model, the proposed imprinted nanorods exhibit an excellent solubility and good homogeneous recognition ability. The imprinting factor for the soluble imprinted nanoroads is 6.8. The equilibrium dissociation constant and the apparent maximum number of the proposed imprinted nanorods are 248.5 μM and 22.1 μmol/g, respectively. We believe that such imprinted nanorods may provide an appealing substitute for natural receptors in homogeneous recognition related fields.

Molecularly imprinted polymers fabricated using Janus particle-stabilized Pickering emulsions and charged monomer polymerization

Janus particle-stabilized Pickering emulsions and their applications in protein interfacial imprinting.

Soluble Molecularly Imprinted Polymer-Based Potentiometric Sensor for Determination of Bisphenol AF

Molecularly imprinted polymer (MIP)-based polymeric membrane potentiometric sensors have been successfully developed for determination of organic compounds in their ionic and neutral forms. However, most of the MIP receptors in potentiometric sensors developed so far are insoluble and cannot be well dissolved in the polymeric membranes. The heterogeneous molecular recognitions between the analytes and MIPs in the membranes are inefficient due to the less available binding sites of the MIPs. Herein we describe a novel polymeric membrane potentiometric sensor using a soluble MIP (s-MIP) as a receptor. The s-MIP is synthesized by the swelling of the traditional MIP at a high temperature. The obtained MIP can be dissolved in the plasticized polymeric membrane for homogeneous binding of the imprinted polymer to the target molecules. By using neutral bisphenol AF as a model, the proposed method exhibits an improved sensitivity compared to the conventional MIP-based sensor with a lower detection limit of 60 nM. Moreover, the present sensor exhibits an excellent selectivity over other phenols. We believe that s-MIPs can provide an appealing substitute for the traditional insoluble MIP receptors in the development of polymeric membrane-based electrochemical and optical sensors.

Construction of stable core–shell imprinted Ag-(poly-o-phenylenediamine)/CoFe2O4 photocatalyst endowed with the specific recognition capability for selective photodegradation of ciprofloxacin

The stable core–shell imprinted Ag-POPD/CoFe₂O₄ photocatalyst not only possessed high photocatalytic activity, but also exhibited the superior specific recognition capability for selective photodegradation of CIP.