Sorption of Acid Green 25 on chitosan: Influence of experimental parameters on uptake kinetics and sorption isotherms

Novel ternary nanocomposite (TiO2@Fe3O4-chitosan) system for nitrate removal from water: an adsorption cum photocatalytic approach

Nitrate pollution of water emerging from various anthropogenic activities has become a major environmental concern because of its deleterious effects on natural water resources. The present work deals with the synthesis of the ternary nanocomposite based on chitosan, iron oxide (Fe3O4), and titanium dioxide (TiO2) and its application for the removal of nitrates from model-contaminated water. Fe3O4 derived through a coprecipitation method was incorporated into the chitosan matrix which was fabricated in the form of beads. The wet gel beads were then successfully coated with sol-gel-derived silver-doped titanium dioxide sol followed by drying under suitable conditions to get the functional nanocomposite beads. The synthesized functional materials were further characterized for their structural, morphological, and textural features using X-ray diffraction analysis, physical property measurement (PPMS), Fourier transform infrared (FTIR) analysis, UV visible spectroscopy analysis (UV-vis), BET surface area analysis (BET), field emission scanning electron microscopic (FESEM), and transmission electron microscopy (TEM) analysis. The ternary nanocomposites were further used for the removal of nitrates via adsorption cum photocatalytic reduction technique from the model contaminated water when subjected to an adsorption study under dark conditions and photocatalytic study under UV/visible/sunlight for a definite time. Fe3O4 in the nanocomposite provides enhanced adsorption features whereas the functional coating of titanium dioxide aids in the removal of nitrates through the photocatalytic reduction technique. The functional beads containing 3% Fe3O4 in the wet gel form (CTA-F3) have excellent nitrate removal efficiency of ~ 97% via adsorption cum solar photocatalysis towards the removal of nitrate ions from 50 ppm nitrate solution, whereas the dried nanocomposite beads have got a nitrate removal efficiency of ~ 68% in 1 h from 100 ppm nitrate solution. Continuous flow adsorption cum photocatalytic study was performed further using the oven-dried functional beads in which flow rate and bed height were varied while maintaining the concentration of feed solution as constant. A nitrate removal efficiency of 65% and an adsorption capacity of 4.1 mgg-1 were obtained for the CTA-F3 beads in the continuous flow adsorption cum photocatalysis experiment for up to 5 h when using an inlet concentration of 100 ppm, bed height 12 cm, and flow rate 5.0 ml min-1. A representative fixed-bed column adsorption experiment conducted using CTA-F3 beads for the treatment of a real groundwater sample shows reasonable results for nitrate removal (71.7% efficiency) along with a significant removal rate for the other anions as well. Thus, the novel adsorbent/photocatalyst developed is suitable for the removal of nitrates from water due to the synergistic effect between Fe3O4, chitosan, and titanium dioxide.

Dye Sorption from Mixtures on Chitosan Sorbents

This article presents studies on the sorption of the anionic dyes Reactive Black 5 (RB5) and Reactive Yellow 84 (RY84) from solutions of single dyes and from dye mixtures onto three chitosan sorbents-chitin, chitosan DD75% and chitosan DD95%. In this work, the influence of pH on sorption efficiency, the sorption equilibrium time for the tested anionic dyes and the sorption capacity in relation to the individual dyes and their mixtures were determined. It has been found that the sorption process for both dyes was most effective at pH 3 for chitin and chitosan DD75 and at pH 4 for chitosan DD95%. The obtained results were described by the double Langmuir equation (Langmuir 2). The obtained constants made it possible to determine the affinity of the tested dyes for the three sorbents and the sorption capacity of the sorbents. For RB5, the highest sorption capacity for chitosan DD95% was achieved with sorption from a single solution-of 742 mg/g DM and with sorption from mixed dyes-of 528 mg/g DM. For RY84, the highest efficiency was also achieved for chitosan DD95% and was 760 mg/g DM for a single dye solution and 437 mg/g DM for a mixture of dyes.

Nanostructured Materials for Water Purification: Adsorption of Heavy Metal Ions and Organic Dyes

Chemical water pollution poses a threat to human beings and ecological systems. The purification of water to remove toxic organic and inorganic pollutants is essential for a safe society and a clean environment. Adsorption-based water treatment is considered one of the most effective and economic technologies designed to remove toxic substances. In this article, we review the recent progress in the field of nanostructured materials used for water purification, particularly those used for the adsorption of heavy metal ions and organic dyes. This review includes a range of nanostructured materials such as metal-based nanoparticles, polymer-based nanomaterials, carbon nanomaterials, bio-mass materials, and other types of nanostructured materials. Finally, the current challenges in the fields of adsorption of toxic materials using nanostructured materials are briefly discussed.

Chitosan@Carboxymethylcellulose/CuO-Co2O3 Nanoadsorbent as a Super Catalyst for the Removal of Water Pollutants

In this work, an efficient nanocatalyst was developed based on nanoadsorbent beads. Herein, carboxymethyl cellulose-copper oxide-cobalt oxide nanocomposite beads (CMC/CuO-Co2O3) crosslinked by using AlCl3 were successfully prepared. The beads were then coated with chitosan (Cs), Cs@CMC/CuO-Co2O3. The prepared beads, CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, were utilized as adsorbents for heavy metal ions (Ni, Fe, Ag and Zn). By using CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, the distribution coefficients (Kd) for Ni, Fe, Ag and Zn were (41.166 and 6173.6 mLg-1), (136.3 and 1500 mLg-1), (20,739.1 and 1941.1 mLg-1) and (86.9 and 2333.3 mLg-1), respectively. Thus, Ni was highly adsorbed by Cs@CMC/CuO-Co2O3 beads. The metal ion adsorbed on the beads were converted into nanoparticles by treating with reducing agent (NaBH4) and named Ni/Cs@CMC/CuO-Co2O3. Further, the prepared nanoparticles-decorated beads (Ni/Cs@CMC/CuO-Co2O3) were utilized as nanocatalysts for the reduction of organic and inorganic pollutants (4-nitophenol, MO, EY dyes and potassium ferricyanide K3[Fe(CN)6]) in the presence of NaBH4. Among all catalysts, Ni/Cs@CMC/CuO-Co2O3 had the highest catalytic activity toward MO, EY and K3[Fe(CN)6], removing up to 98% in 2.0 min, 90 % in 6.0 min and 91% in 6.0 min, respectively. The reduction rate constants of MO, EY, 4-NP and K3[Fe(CN)6] were 1.06 × 10-1, 4.58 × 10-3, 4.26 × 10-3 and 5.1 × 10-3 s-1, respectively. Additionally, the catalytic activity of the Ni/Cs@CMC/CuO-Co2O3 beads was effectively optimized. The stability and recyclability of the beads were tested up to five times for the catalytic reduction of MO, EY and K3[Fe(CN)6]. It was confirmed that the designed nanocomposite beads are ecofriendly and efficient with high strength and stability as catalysts for the reduction of organic and inorganic pollutants.

Sustainable Removal of Contaminants by Biopolymers: A Novel Approach for Wastewater Treatment. Current State and Future Perspectives

Naturally occurring substances or polymeric biomolecules synthesized by living organisms during their entire life cycle are commonly defined as biopolymers. Different classifications of biopolymers have been proposed, focusing on their monomeric units, thus allowing them to be distinguished into three different classes with a huge diversity of secondary structures. Due to their ability to be easily manipulated and modified, their versatility, and their sustainability, biopolymers have been proposed in different fields of interest, starting from food, pharmaceutical, and biomedical industries, (i.e., as excipients, gelling agents, stabilizers, or thickeners). Furthermore, due to their sustainable and renewable features, their biodegradability, and their non-toxicity, biopolymers have also been proposed in wastewater treatment, in combination with different reinforcing materials (natural fibers, inorganic micro- or nano-sized fillers, antioxidants, and pigments) toward the development of novel composites with improved properties. On the other hand, the improper or illegal emission of untreated industrial, agricultural, and household wastewater containing a variety of organic and inorganic pollutants represents a great risk to aquatic systems, with a negative impact due to their high toxicity. Among the remediation techniques, adsorption is widely used and documented for its efficiency, intrinsic simplicity, and low cost. Biopolymers represent promising and challenging adsorbents for aquatic environments’ decontamination from organic and inorganic pollutants, allowing for protection of the environment and living organisms. This review summarizes the results obtained in recent years from the sustainable removal of contaminants by biopolymers, trying to identify open questions and future perspectives to overcome the present gaps and limitations.

Starch, cellulose, pectin, gum, alginate, chitin and chitosan derived (nano)materials for sustainable water treatment: A review

Natural biopolymers, polymeric organic molecules produced by living organisms and/or renewable resources, are considered greener, sustainable, and eco-friendly materials. Natural polysaccharides comprising cellulose, chitin/chitosan, starch, gum, alginate, and pectin are sustainable materials owing to their outstanding structural features, abundant availability, and nontoxicity, ease of modification, biocompatibility, and promissing potentials. Plentiful polysaccharides have been utilized for making assorted (nano)catalysts in recent years; fabrication of polysaccharides-supported metal/metal oxide (nano)materials is one of the effective strategies in nanotechnology. Water is one of the world's foremost environmental stress concerns. Nanomaterial-adorned polysaccharides-based entities have functioned as novel and more efficient (nano)catalysts or sorbents in eliminating an array of aqueous pollutants and contaminants, including ionic metals and organic/inorganic pollutants from wastewater. This review encompasses recent advancements, trends and challenges for natural biopolymers assembled from renewable resources for exploitation in the production of starch, cellulose, pectin, gum, alginate, chitin and chitosan-derived (nano)materials.

Biomass Modification Using Cationic Surfactant Cetyltrimethylammonium Bromide (CTAB) to Remove Palm-Based Cooking Oil

Adsorption based on natural fibre seems to widely used for oily wastewater recovery due to its low cost, simplicity, feasibility, easy handling, and effectiveness. However, oil sorbent based on natural fibre without modification has low adsorption capacity and selectivity. Thus, this paper proposes chemical modification of sago hampas to improve its adsorbent efficiency for the removal of palm-based cooking oil. The chemical modification was performed using a cationic surfactant, cetyltrimethylammonium bromide (CTAB). The chemical and surface properties of both unmodified and modified sago hampas were characterized by Fourier-Transform Infrared (FTIR) and Scanning Electron Microscopy (SEM). Parameters studied for the removal of cooking oil using modified sago hampas were sorption time, adsorbent dosage, and initial pH. The removal capacity was also compared using unmodified sago hampas. The results showed that additional functional groups were introduced on the surface of modified sago hampas. Modified sago hampas also showed a greater porosity than unmodified sago hampas. These properties enhanced the adsorption of palm-based cooking oil onto the surface of modified sago hampas. Modified sago hampas shows better removal of palm-based cooking oil than unmodified sago hampas, where 84.82% and 68.08% removal were achieved by modified and unmodified sago hampas, respectively. The optimum adsorption of palm-based cooking oil was identified at 45 min sorption time, pH 2, and 0.2 g adsorbent dosage.

Adsorption removal of anionic dyes from aqueous solutions by chitosan nanoparticles deposited on the fibrous carrier

The synthesis, characterization and environmental application of chitosan based material stable in acidic media for adsorption of anionic dyes were investigated. The adsorption material is chitosan nanoparticles immobilized on a fibrous carrier (CPF). The choice of optimal conditions for the preparation of chitosan particles and their immobilization on a chemically activated polyethylene terephthalate (PET) fiber is justified. Immobilized nanoparticles showed high adsorption rates and dye binding capacity (300-1050 mg g^-1) depending on the dye type. Anionic phthalocyanine dyes having different molecular sizes, different nature and number of anionic groups were used as model adsorbates. The experimental isotherm data and a linear correlation coefficients (r_L² > 0.99) have shown that the dyes adsorption on CPF is best predicted by the Langmuir isotherm. The adsorption rate has been found to conform to pseudo-second-order kinetics with a good correlation (R² > 0.99) with intra-particle diffusion as one of the rate determining steps. It has been is established that the sorption rate and the limiting sorption capacity decrease with the increment in the dye molecule size. The process of adsorption of the dyes on the CPF is pH-insensitive in the pH range of 2-8. The adsorption saturated CPF could be effectively regenerated by a simple alkaline washing.

Marine carbohydrates of wastewater treatment

Our natural heritage (rivers, seas, and oceans) has been exploited, mistreated, and contaminated because of industrialization, globalization, population growth, urbanization with increased wealth, and more extravagant lifestyles. The scenario gets worse when the effluents or contaminants are discharged directly. So wastewater treatment is a very important and necessary in nowadays to purify wastewater before it enters a body of natural water, or it is applied to the land, or it is reused. Various methods are available for treating wastewater but with many disadvantages. Recently, numerous approaches have been studied for the development of cheaper and more effective technologies, both to decrease the amount of wastewater produced and to improve the quality of the treated effluent. Biosorption is an emerging technology, which uses natural materials as adsorbents for wastewater treatment. Low-cost adsorbents of polysaccharide-based materials obtained from marine, such as chitin, chitosan, alginate, agar, and carrageenan, are acting as rescue for wastewater treatment. This chapter reviews the treatment of wastewater up to the present time using marine polysaccharides and its derivatives. Special attention is paid to the advantages of the natural adsorbents, which are a wonderful gift for human survival.

The Change from Past to Future for Adsorbent Materials in Treatment of Dyeing Wastewaters

Adsorption is one of the most promising decolorization techniques in dyeing wastewater treatment. Adsorption techniques for wastewater treatment have become more popular in recent years owing to their efficiency in the removal of pollutants too stable for biological methods. Dye adsorption is a result of two mechanisms (adsorption and ion exchange) and is influenced by many factors as dye/adsorbent interaction, adsorbent’s surface area, particle size, temperature, pH, and contact time. The main advantage of adsorption recently became the use of low-cost materials, which reduces the procedure cost. The present review firstly introduced the technology process, research history and research hotspot of adsorption. Then, the application of adsorption in treatment of dyeing wastewaters in the past decades was summarized, revealing the impressive changes in modes, trends, and conditions. From this review article, the different philosophy of synthesis of adsorbent materials became evident.

Decolorization of dye wastewaters by biosorbents: a review

Dye wastewater is one of the most difficult to treat. There has been exhaustive research on biosorption of dye wastewater. It is evolving as an attractive option to supplement conventional treatment processes. This paper examines various biosorbents such as fungi, bacteria, algae, chitosan and peat, which are capable of decolorizing dye wastewaters; discusses various mechanism involved, the effects of various factors influencing dye wastewater decolorization and reviews pretreatment methods for increasing the biosorption capacity of the adsorbents. The paper examines the mismatch between strong scientific progress in the field of biosorption and lack of commercialization of research.

Efficient removal of dyes in water using chitosan microsphere supported cobalt (II) tetrasulfophthalocyanine with H2O2

A new efficient catalyst, CoTSPc@chitosan, was developed by immobilizing water soluble cobalt (II) tetrasulfophthalocyanine onto adsorbent chitosan microspheres covalently for the heterogeneous catalytic oxidation of C. I. Acid Red 73 with H(2)O(2). The result indicated that the COD removal and discoloration of C. I. Acid Red 73 made 55 and 95% respectively in the presence of CoTSPc@chitosan with H(2)O(2) in 4h. In addition, CoTSPc@chitosan-H(2)O(2) system could proceed efficiently in a relatively wide pH range and remain high catalytic activity after 6 reuse cycles. Furthermore, the adsorption study of CoTSPc@chitosan confirmed that chitosan was an outstanding support which contributed a lot to the removal reaction. In conclusion, the combination of adsorption process and catalytic oxidation made the CoTSPc@chitosan-H(2)O(2) system achieve a simple, efficiently and environmentally friendly water treatment.

Removal of an anionic dye (Acid Blue 92) by coagulation-flocculation using chitosan

Chitosan (a biopolymer) is an aminopolysaccharide that can be used for the treatment of colored solutions by coagulation-flocculation (as an alternative to more conventional processes such as sorption). Acid Blue 92 (a sulfonic dye) was selected as a model dye for verifying chitosan's ability to treat textile wastewater. A preliminary experiment demonstrated that chitosan was more efficient at color removal in tap water than in demineralized water, and that a substantially lower concentration of chitosan could be used with tap water. Dye removal reached up to 99% under optimum concentration; i.e., in terms of the acidic solutions and the stoichiometric ratio between the amine groups of the biopolymer and the sulfonic groups in the dye. The flocs were recovered and the dye was efficiently removed using alkaline solutions (0.001-1 M NaOH solutions) and the biopolymer, re-dissolved in acetic acid solution, was reused in a further treatment cycle.

Effect of structural properties of acid dyes on their adsorption behaviour from aqueous solutions by amine modified silica

Monoamine modified silica particles (MAMS) were prepared and characterized by infrared (FT-IR) and thermogravimetric analysis (TGA). The modified silica particles were used for removal of acid orange 10 (AO-10) and acid orange 12 (AO-12) from their aqueous solutions. The adsorption behaviour of the two dyes was studied at different experimental conditions of pH, contact time, concentration of dye, temperature and salt solution. The adsorption of AO-10 followed pseudo-first order kinetics whereas AO-12 followed pseudo-second order. The two dyes showed different modes of interaction with silica surface. Desorption of the loaded dyes was carried out at pH 10 and found to be 10.4 and 91.6% for AO-12 and AO-10, respectively.

Chitosan and chemically modified chitosan beads for acid dyes sorption

The capabilities of chitosan and chitosan-EGDE (ethylene glycol diglycidyl ether) beads for removing Acid Red 37 (AR 37) and Acid Blue 25 (AB 25) from aqueous solution were examined. Chitosan beads were cross-linked with EGDE to enhance its chemical resistance and mechanical strength. Experiments were performed as a function of pH, agitation period and concentration of AR 37 and AB 25. It was shown that the adsorption capacities of chitosan for both acid dyes were comparatively higher than those of chitosan-EGDE. This is mainly because cross-linking using EGDE reduces the major adsorption sites -NH3+ on chitosan. Langmuir isotherm model showed the best conformity compared to Freundlich and BET. The kinetic experimental data agreed very well to the pseudo second-order kinetic model. The desorption study revealed that after three cycles of adsorption and desorption by NaOH and HCl, both adsorbents retained their promising adsorption abilities. FT-IR analysis proved that the adsorption of acid dyes onto chitosan-based adsorbents was a physical adsorption. Results also showed that chitosan and chitosan-EGDE beads were favourable adsorbers and could be employed as low-cost alternatives for the removal of acid dyes in wastewater treatment.

The removal of Basic Blue 3 from aqueous solutions by chitosan-based adsorbent: batch studies

Chitosan-based adsorbent (CHITOD material) is used for the removal of Basic Blue 3 (BB 3) from aqueous solutions. The adsorption of BB 3 on CHITOD material was studied as a function of time, sorbent mass and concentration. The influence of these parameters on the adsorption capacity was evaluated using the batch method. Results of adsorption experiments and kinetic data showed that (i) the CHITOD adsorbent exhibited high sorption capacities toward BB 3; (ii) the Langmuir equation represented the best fit of experimental data; (iii) the dye sorption on material was exothermic and spontaneous in nature; (iv) the kinetic measurements showed that the process was rapid; (v) the adsorption kinetics followed a pseudo-second order model; and (vi) the sorption was dependent on the presence of sulfonate groups. Non-linear method was also found to be more appropriate method for estimating the isotherm and kinetic parameters.

Influence of chitosan characteristics on the coagulation and the flocculation of bentonite suspensions

Ten chitosan preparations with different molecular weights (MW) and degrees of deacetylation (DD) were tested for coagulation of 5 g L(-1) bentonite suspensions at pH 5 and 7 in demineralized water (DW) and in tap water (TW). Coagulation was better in TW than in DW for every condition and lower doses of chitosan were required at pH 5 than at pH 7. More than 95% of residual turbidity (after sedimentation in the absence of chitosan) was removed using less than 0.10 mg L(-1) chitosan in either TW or DW at pH 5 or in TW at pH 7. Higher doses were required for removal of turbidity in DW at pH 7, but in all cases the effective concentrations of chitosan were much lower than required for complete neutralization of the negative charge on the bentonite particles. Removal of turbidity was best for the higher MW chitosans in either the B series (89.5% DD) or the C series (95% DD) of chitosans. Overall, the results were consistent with destabilization of bentonite by the combined mechanisms of electrostatic patch and bridging. The improved performance of chitosan in TW could have been due to improved attachment to bentonite due to the presence of sulfate and other counter-ions in TW.