Forefront Research of Foaming Strategies on Biodegradable Polymers and Their Composites by Thermal or Melt-Based Processing Technologies: Advances and Perspectives

The last few decades have witnessed significant advances in the development of polymeric-based foam materials. These materials find several practical applications in our daily lives due to their characteristic properties such as low density, thermal insulation, and porosity, which are important in packaging, in building construction, and in biomedical applications, respectively. The first foams with practical applications used polymeric materials of petrochemical origin. However, due to growing environmental concerns, considerable efforts have been made to replace some of these materials with biodegradable polymers. Foam processing has evolved greatly in recent years due to improvements in existing techniques, such as the use of supercritical fluids in extrusion foaming and foam injection moulding, as well as the advent or adaptation of existing techniques to produce foams, as in the case of the combination between additive manufacturing and foam technology. The use of supercritical CO2 is especially advantageous in the production of porous structures for biomedical applications, as CO2 is chemically inert and non-toxic; in addition, it allows for an easy tailoring of the pore structure through processing conditions. Biodegradable polymeric materials, despite their enormous advantages over petroleum-based materials, present some difficulties regarding their potential use in foaming, such as poor melt strength, slow crystallization rate, poor processability, low service temperature, low toughness, and high brittleness, which limits their field of application. Several strategies were developed to improve the melt strength, including the change in monomer composition and the use of chemical modifiers and chain extenders to extend the chain length or create a branched molecular structure, to increase the molecular weight and the viscosity of the polymer. The use of additives or fillers is also commonly used, as fillers can improve crystallization kinetics by acting as crystal-nucleating agents. Alternatively, biodegradable polymers can be blended with other biodegradable polymers to combine certain properties and to counteract certain limitations. This work therefore aims to provide the latest advances regarding the foaming of biodegradable polymers. It covers the main foaming techniques and their advances and reviews the uses of biodegradable polymers in foaming, focusing on the chemical changes of polymers that improve their foaming ability. Finally, the challenges as well as the main opportunities presented reinforce the market potential of the biodegradable polymer foam materials.

Fabrication, property characterization, and benefit analysis of mixing mechanism of nitrogen and melt, and its comparison of the porous-foam polypropylene injection molding parts

In this study, an injection molding machine with a mixing mechanism of nitrogen (N2) and melt was designed, and the melt-fill/porous-foaming behavior is observed under the novel barrel design (plasticizing stage) of the gas/melt mixing for the porous injection molded thermoplastic. The thermoplastic employed in this study was polypropylene (PP), and the gas for forming the porous structure is N2. In addition, a thickness of 5 mm and a width of 10 mm paper-clip shape and the mold were constructed for studying the melt-fill-length and fill-length ratio through an experiment. The experimental results showed that the use of an injection molding machine with a mixing mechanism of N2 and melt decreased the melt-fill-length when the N2-output pressure was increased. The reason is that when the gas output, the speed of the screw will be affected. Therefore, during the gas/melt mixing and the plasticization rate will also affect the volume of the foam and the melt. But during plasticizing setting back pressure, can improve its melt volume reduction. When passing through the mixing mechanism and the injected melt, the melt is filled into the mold cavity, and the pressure in the melt is released/porous-foaming grows. At the same time, when the output pressure increases, the amount of melt in the injection barrel will decrease, and its relative porous structure/density distribution will increase. In addition, the mixing/flow direction of the melt impacted the density distribution and dispersion of porous foaming, thus the sample weight/shrinkage of melt-fill-length test sample (Mfl-ts) was improved.

A study of the cell morphology and mechanical properties of bumper material PP-T-EPDM composite foam

In this study, cellular polypropylene based composite foams were prepared using an universal injection moulding machine. The chemical foaming agent was added to neat polypropylene (PP) polymer, talc filled polypropylene (PP-T) composite and talc filled polypropylene/ethylene-propylene-diene blend (PP-T-EPDM) composite materials at the ratio of 1% and 2% by weight. The influence of foaming agent content on the mechanical and cellular properties of both neat PP polymer and PP composites was investigated. The results showed that the tensile strength, tensile modulus, impact strength, hardness, cell diameter, foam density and viscosity values and skin layer thickness decreased while volume expansion ratio increased with the increment in chemical blowing agent content.

Improvement of Mechanical and Biological Properties of PLA/HNT Scaffolds Fabricated by Foam Injection Molding: Skin Layer Effect and Laser Texturing

Polylactic acid (PLA) is one of the important materials for orthopedic regenerative engineering applications due to its biodegradability and biocompatibility. Nonetheless, PLA may show insufficient mechanical strength for some bone replacement applications. Halloysite nanotube (HNT) is one of the non-toxic, biocompatible reinforcement for improving mechanical and biological properties of PLA for tissue engineering applications. In this study, PLA/HNT scaffolds were prepared by chemical foam injection molding process. Laser surface texturing was applied on the skin layer of the injection molded scaffolds to enhance the cell viability and hydrophilicity of PLA. The effects of HNT concentration on cell morphology, mechanical and thermal properties, cell viability and biodegradation profile of the scaffolds were studied. The results demonstrated that cell viability increased by 43% in PLA/HNT scaffolds compared to neat PLA. Hydrophilicity of the scaffolds that have thick skin layer was enhanced by the laser surface texturing in two different designs and consequently, cell viability increased about 16%. Surface roughness measurements and water contact angle measurements have verified this result.

Backpressure Optimization in Foam Injection Molding: Method and Assessment of Sustainability

Inspired by the Industry 4.0 trend towards greater user-friendliness and self-optimization of machines, we present a novel approach to reducing backpressure in foam injection molding. Our method builds on the compressibility of polymer-gas mixtures to detect undissolved gas phases during processing at insufficient backpressures. Identification of a characteristic behavior of the bulk modulus upon transition from homogeneous to heterogeneous polymer-gas mixtures facilitated the determination of the minimum pressure required during production to be determined, as verified by ultrasound measurements. Optimization of the pressure conditions inside the barrel by means of our approach saves resources, making the process more sustainable. Our method yielded a 45% increase in plasticizing capacity, reduced the torque needed by 24%, and required 46% less plasticizing work and lower pressures in the gas supply chain. The components produced exhibited both improved mechanical bending properties and lower densities. From an economic point of view, the main advantages of optimized backpressures are reduced wear and lower energy consumption. The methodology presented in this study has considerable potential in terms of sustainable production and offers the prospect of fully autonomous process optimization.

Lightweight High-Performance Polymer Composite for Automotive Applications

The automotive industry needs to produce plastic products with high dimensional accuracy and reduced weight, and this need drives the research toward less conventional industrial processes. The material that was adopted in this work is a glass-fiber-reinforced polyamide 66 (PA66), a material of great interest for the automotive industry because of its excellent properties, although being limited in application because of its relatively high cost. In order to reduce the cost of the produced parts, still preserving the main properties of the material, the possibility of applying microcellular injection molding process was explored in this work. In particular, the influence of the main processing parameters on morphology and performance of PA66 + 30% glass-fiber foamed parts was investigated. An analysis of variance (ANOVA) was employed to identify the significant factors that influence the morphology of the molded parts. According to ANOVA results, in order to obtain homogeneous foamed parts with good mechanical properties, an injection temperature of 300 °C, a high gas injection pressure, and a large thickness of the parts should be adopted.

Chemical Modification and Foam Processing of Polylactide (PLA)

Polylactide (PLA) is known as one of the most promising biopolymers as it is derived from renewable feedstock and can be biodegraded. During the last two decades, it moved more and more into the focus of scientific research and industrial use. It is even considered as a suitable replacement for standard petroleum-based polymers, such as polystyrene (PS), which can be found in a wide range of applications-amongst others in foams for packaging and insulation applications-but cause strong environmental issues. PLA has comparable mechanical properties to PS. However, the lack of melt strength is often referred to as a drawback for most foaming processes. One way to overcome this issue is the incorporation of chemical modifiers which can induce chain extension, branching, or cross-linking. As such, a wide variety of substances were studied in the literature. This work should give an overview of the most commonly used chemical modifiers and their effects on rheological, thermal, and foaming behavior. Therefore, this review article summarizes the research conducted on neat and chemically modified PLA foamed with the conventional foaming methods (i.e., batch foaming, foam extrusion, foam injection molding, and bead foaming).

Structural Foams of Biobased Isosorbide-Containing Copolycarbonate

Isosorbide-containing copolycarbonate (Bio-PC) is a partly biobased alternative to conventional bisphenol A (BPA) based polycarbonate (PC). Conventional PC is widely used in polymer processing technologies including thermoplastic foaming such as foam injection molding. At present, no detailed data is available concerning the foam injection molding behavior and foam properties of Bio-PC. This contribution provides first results on injection-molded foams based on isosorbide-containing PC. The structural foams were produced by using an endothermic chemical blowing agent (CBA) masterbatch and the low pressure foam injection molding method. The influence of weight reduction and blowing agent concentration on general foam properties such as density, morphology, and mechanical properties was studied. The test specimens consist of a foam core in the center and compact symmetrical shell layers on the sides. The thickness of the foam core increases with increasing weight reduction irrespective of the CBA concentration. The specific (mechanical) bending properties are significantly improved and the specific tensile properties can almost be maintained while reducing the density of the injection-molded parts.

Micromechanical Characterization of Complex Polypropylene Morphologies by HarmoniX AFM

This paper examines the capability of the HarmoniX Atomic Force Microscopy (AFM) technique to draw accurate and reliable micromechanical characterization of complex polymer morphologies generally found in conventional thermoplastic polymers. To that purpose, injection molded polypropylene samples, containing representative morphologies, have been characterized by HarmoniX AFM. Mapping and distributions of mechanical properties of the samples surface are determined and analyzed. Effects of sample preparation and test conditions are also analyzed. Finally, the AFM determination of surface elastic moduli has been compared with that obtained by indentation tests, finding good agreement among the results.

Effect of processing condition on properties of polylactic acid parts obtained by foam injection molding

Foam injection molding is a processing technology particularly interesting for biodegradable polymers, which present a very narrow processing window, with the suitable processing temperatures close to the degradation conditions. The addition of a physical blowing agent, besides decreasing the final part weight, reduces both the viscosity and the glass transition temperature of the polymer melt, allowing the processability of these materials at lower temperatures. In this work, structural foams of polylactic acid with nitrogen as physical blowing agent were obtained by foam injection molding. In particular, the effects of back pressure, namely the pressure imposed inside of the cylinder when the screw is returning back to prepare a new amount of material to be injected, and of the injection flow rate on foaming and mechanical properties of the molded parts was assessed. It was found that the samples molded adopting a higher injection flow rate are shorter than those injected at lower flow rate, and this result was ascribed to the large compressibility of the injected shot. As far as the mechanical properties of the foamed parts, it was found that the modulus decreases with decreasing density. However, the density reduction is not the only significant parameter, but also the morphology of the foams should be taken into account in order to justify the differences between tensile and flexural modulus.