Effective incorporation of TiO2nanoparticles into polyamide thin-film composite membranes

The role of sheet-like TiO2 in polyamide reverse osmosis membrane for enhanced removal of endocrine disrupting chemicals

Thin film composite (TFC) reverse osmosis (RO) membrane shows good promise for treating wastewater containing endocrine disrupting chemical (EDC) pollutants. The incorporation of functional materials with exceptional structural and physico-chemical properties offers opportunities for the membranes preparation with enhanced permselectivity and better antifouling properties. The present study aims to improve the EDC removal efficiency of TFC RO membrane using two-dimensional titania nanosheets (TNS). RO membrane was prepared by incorporating TNS in the dense layer of polyamide (PA) layer to form thin film nanocomposite (TFN) membrane. The TNS loading was varied and the influences on membrane morphology, surface hydrophilicity, surface charge, as well as water permeability and rejection of EDC were investigated. The results revealed that the inclusion of TNS in the membrane resulted in the increase of water permeability and EDC rejection. When treating the mixture of bisphenol A (BPA) and caffeine at 100 ppm feed concentration, the TFN membrane incorporated with 0.05% TNS achieved water permeability of 1.45 L/m2·h·bar, which was 38.6% higher than that of unmodified TFC membrane, while maintaining satisfactory rejection of >97%. The enhancement of water permeability for TFN membrane can be attributed to their hydrophilic surface and unique nanochannel structure created by the nanoscale interlayer spacing via staking of TiO2 nanosheets. Furthermore, the 0.05TFN membrane exhibited excellent fouling resistance towards BPA and caffeine pollutants with almost 100% flux recovery for three cycles of operations.

In Situ Formation of Silver Nanoparticles Induced by Cl-Doped Carbon Quantum Dots for Enhanced Separation and Antibacterial Performance of Nanofiltration Membrane

Polyamide (PA) nanofiltration (NF) membranes suffer from biofouling, which will deteriorate their separation performance. In this study, we proposed a strategy to incorporate silver nanoparticles (Ag NPs) into PA NF membranes in situ, in order to simultaneously enhance water permeability and antibacterial performance. The chloride-doped carbon quantum dots (Cl-CQDs) with photocatalytic performance were pre-embedded in the PA selective layer. Under visible light irradiation, the photogenerated charge carriers generated by Cl-CQDs rapidly transported to silver ions (Ag+ ions), resulting in the in situ formation of Ag NPs. The proposed strategy avoided the problem of aggregating Ag NPs, and the amount of Ag NPs on the membrane surfaces could be easily tuned by changing silver nitrate (AgNO3) concentrations and immersion times. These uniformly dispersed Ag NPs increased membrane hydrophilicity. Thus, the obtained thin film nanocomposite Ag NPs (TFN-Ag) membrane exhibited an improved water flux (31.74 L m-2 h-1), which was ~2.98 times that of the pristine PA membrane; meanwhile, the sodium sulfate (Na2SO4) rejection rate was 96.11%. The sterilization rates of the TFN-Ag membrane against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were 99.55% and 99.52%, respectively. Thus, this facile strategy simultaneously improved the permeability and antibacterial property of PA NF membranes.

Performance study of fouling resistant novel ultrafiltration membranes based on the blends of poly (ether ether sulfone)/poly (vinyl pyrrolidone)/nano-titania for the separation of humic acid, dyes and biological macromolecular proteins from aqueous solutions

This study explains the use of a ultrafiltration membrane made of polyvinyl pyrrolidone (PVP) and poly(ether ether sulfone) (PEES)/Nano-titania (n-TiO₂) for the separation of organic compounds. The results of the tests for porosity, water content, surface chemistry, membrane morphology, and contact angle demonstrated that the developed membranes have more hydrophilicity than PEES membranes due to the redundant hydrophilic nature of PVP and n-TiO₂. The membrane pure water flux, which contains 5 wt% PVP and 1.5 wt% n-TiO_2, was 312.76 Lm^-2h^-1, about three-fold higher than that of pristine membrane (95.71 Lm^-2h^-1). Employing bovine serum albumin as a model foulant, the fouling resistance of the PEES/PVP/n-TiO₂ membrane was examined. According to the analysis of flux recovery ratio and irreversible resistance, modified membranes were less likely to foul, and the PEES/n-TiO₂ membrane with 5% PVP addition was recommended as optimal. The fabricated membranes effectively removed more than 95% of various organic compounds such as humic acid, safranin O, egg albumin, pepsin, and trypsin from aqueous solution. Permeability of safranin O and humic acid of PEES/PVP/n-TiO₂ membranes was about 118 Lm^-2h^-1 and 138 Lm^-2h^-1, respectively.

Chitosan-Based Nanocomposite Polymeric Membranes for Water Purification-A Review

During the past few years, researchers have focused their attention on developing innovative nanocomposite polymeric membranes with applications in water purification. Natural and synthetic polymers were considered, and it was proven that chitosan-based materials presented important features. This review presents an overview regarding diverse materials used in developing innovative chitosan-based nanocomposite polymeric membranes for water purification. The first part of the review presents a detailed introduction about chitosan, highlighting the fact that is a biocompatible, biodegradable, low-cost, nontoxic biopolymer, having unique structure and interesting properties, and also antibacterial and antioxidant activities, reasons for using it in water treatment applications. To use chitosan-based materials for developing nanocomposite polymeric membranes for wastewater purification applications must enhance their performance by using different materials. In the second part of the review, the performance's features will be presented as a consequence of adding different nanoparticles, also showing the effect that those nanoparticles could bring on other polymeric membranes. Among these features, pollutant's retention and enhancing thermo-mechanical properties will be mentioned. The focus of the third section of the review will illustrate chitosan-based nanocomposite as polymeric membranes for water purification. Over the last few years, researchers have demonstrated that adsorbent nanocomposite polymeric membranes are powerful, important, and potential instruments in separation or removal of pollutants, such as heavy metals, dyes, and other toxic compounds presented in water systems. Lastly, we conclude this review with a summary of the most important applications of chitosan-based nanocomposite polymeric membranes and their perspectives in water purification.

Antibacterial behaviour of surface modified composite polyamide nanofiltration (NF) membrane by immobilizing Ag-doped TiO2 nanoparticles

Modification of active membrane surface is an auspicious way to enhance the membrane performance. In our study, a commercially available composite polyamide Nanofiltration (NF) membrane was modified by immobilizing silver doped TiO₂ (Ag-TiO₂) nanoparticles. Ag-TiO₂ with different nanoparticles concentration (0.05, 0.1, and 0.5 wt. %) were coated on the surface of the membrane by a dip coating method. The evidence of successful coating was evaluated by Scanning Electron Microscopy coupled with Energy Dispersive Spectroscopy and Atomic Force Microscopy images. Moreover, the Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), contact angle measurement and permeation tests were carried out in order to evaluate the membrane performance after coating. The antifouling property of the modified membrane was evaluated for Gram-positive (Bacillus subtilis) and Gram-negative (Escherichia coli) bacteria by colony counting method. The results indicated that the modified membranes keep efficient antibacterial efficacy against both types of bacteria. The bacterial growth reduced approximately 93% and 91% on the modified membrane as compared to the unmodified membrane for E.coli and B.subtilis, respectively. Ag-TiO₂ nanoparticles imbedded nanofiltration membranes inhibit the biofilm formation and facilitate in cleaning membrane surface without using excessive chemical agents.

Antifouling Properties of Silver-Zinc Oxide Polyamide Thin Film Composite Membrane and Rejection of 2-Chlorophenol and 2,4-Dichlorophenol

The silver-zinc oxide (Ag-ZnO) polyamide thin film composite (PA-TFC) membrane was prepared by interfacial polymerization. The Ag-ZnO/PA-TFC membrane was characterized by attenuated total reflectance fourier-transform infrared spectroscopy (ATR-FTIR) for polyamide functional groups and contact angle for surface hydrophilicity. The Ag-ZnO/PA-TFC membrane was further characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) for morphology and surface roughness, respectively. The performance of the fabricated membrane was investigated using pure water flux, permeability, rejection, flux recovery, and fouling resistance using low molecular weight organic pollutants, 2-chlorophenol (2-CP) and 2,4-dichlorophenol (2,4-DCP). The results were compared to the neat (PA-TFC) membrane. It was observed that incorporation of Ag-ZnO nanocomposites into the PA-TFC membrane improved hydrophilicity, permeation, rejection, and fouling resistance properties of the membrane. The contact angle decreased from 62.8° to 54° for PA-TFC and the Ag-ZnO/PA-TFC membrane, respectively. The presence of Ag-ZnO enhanced permeability of the membrane from 0.9 (Lm-2h-1bar-1) to 1.9 (Lm-2h-1bar-1). Modification of the membrane with Ag-ZnO further showed an enhanced rejection of 2-CP and 2,4-DCP from 43% to 80% and 58% to 85%, respectively. The 2,4-DCP molecules were rejected more than 2-CP due to enhanced repulsive forces from the extra Cl ion. A high flux recovery of about 95% was achieved for the modified membrane compared to 64% for the neat membrane. The improved flux recovery was an indication of enhanced antifouling propensity.

Progress of Nanocomposite Membranes for Water Treatment

The use of membrane-based technologies has been applied for water treatment applications; however, the limitations of conventional polymeric membranes have led to the addition of inorganic fillers to enhance their performance. In recent years, nanocomposite membranes have greatly attracted the attention of scientists for water treatment applications such as wastewater treatment, water purification, removal of microorganisms, chemical compounds, heavy metals, etc. The incorporation of different nanofillers, such as carbon nanotubes, zinc oxide, graphene oxide, silver and copper nanoparticles, titanium dioxide, 2D materials, and some other novel nano-scale materials into polymeric membranes have provided great advances, e.g., enhancing on hydrophilicity, suppressing the accumulation of pollutants and foulants, enhancing rejection efficiencies and improving mechanical properties and thermal stabilities. Thereby, the aim of this work is to provide up-to-date information related to those novel nanocomposite membranes and their contribution for water treatment applications.

Modification of Polyamide-Urethane (PAUt) Thin Film Composite Membrane for Improving the Reverse Osmosis Performance

In the current study, the poly (amide-urethane) (PAUt) membranes were successfully fabricated by interfacial polymerization of m-phenylenediamine (MPD) and 5-choroformyloxyisophaloyl chloride (CFIC) on the polysulfone substrates. Two modification methods based on layer-by-layer assembly were applied to modify the PAUt membrane surface to achieve antifouling property: 1. Chitosan (CS) was directly self-assembled on the PAUt membrane (i.e., PAUt-CS); and 2. polydimethyl diallyl ammonium chloride (PDDA), polystyrene sulfonate (PSS), and CS were successively self-assembled on the membrane surface (i.e., PAUt-PDDA/PSS/CS). The resultant membranes were symmetrically characterized by Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Contact Angle Meter (CAM), respectively. The results indicated that the modified membranes had much smoother and more hydrophilic surfaces as compared to the nascent PAUt membrane. Meanwhile, the modified membranes exhibited better reverse osmosis performance in terms of water permeability and salt rejection. After the modified membranes were fouled by lake water, the PAUt-PDDA/PSS/CS membrane presented the best antifouling performance among the three types of membranes. Combining the reverse osmosis performance with the anti-fouling property obviously, the PAUt-PDDA/PSS/CS membrane behaved as a promising candidate to be used in real applications.

Surface Engineering of Thin Film Composite Polyamide Membranes with Silver Nanoparticles through Layer-by-Layer Interfacial Polymerization for Antibacterial Properties

We developed a simple and facile approach to covalently immobilize Ag nanoparticles (NPs) onto polyamide surfaces of thin film composite membranes through layer-by-layer interfacial polymerization (LBL-IP) for biofouling mitigation. Stable and uniform bovine serum albumin (BSA) capped Ag NPs with an average diameter of around 20 nm were synthesized using BSA as a template under the assistance of sonication, and Ag NPs incorporated thin film composite (TFC) polyamide membrane was then fabricated by LBL-IP on a nanoporous polysulfone (PSf) substrate upon sequential coating with m-phenylenediamine (MPD) aqueous solution, trimesoyl chloride (TMC)-hexane solution, and finally BSA-capped Ag NPs aqueous solution. The influence of Ag NPs incorporation was investigated on the surface physicochemical properties, water permeability, and salt rejection of TFC polyamide membrane. Our findings show that Ag NPs functionalized membrane exhibited excellent antibacterial properties without sacrificing their permeability and rejection, and Ag NPs incorporation affected very little surface roughness and charge of polyamide layer. Moreover, the incorporated Ag NPs presented a low release rate and excellent stability on polyamide surface in cross-flow conditions. Given the simplicity and versatility of this approach, our study provides a practicable avenue for direct incorporation of various surface-tailored nanomaterials on the polyamide surface to develop high-performance TFC membranes with fouling-resistant properties on a large scale.

Nanoscale Pillar-Enhanced Tribological Surfaces as Antifouling Membranes

We present a nonconventional membrane surface modification approach that utilizes surface topography to manipulate the tribology of foulant accumulation on water desalination membranes via imprinting of submicron titanium dioxide (TiO₂) pillar patterns onto the molecularly structured, flat membrane surface. This versatile approach overcomes the constraint of the conventional approach relying on interfacial polymerization that inevitably leads to the formation of ill-defined surface topography. Compared to the nonpatterned membranes, the patterned membranes showed significantly improved fouling resistance for both organic protein and bacterial foulants. The use of hydrophilic TiO₂ as a pattern material increases the membrane hydrophilicity, imparting improved chemical antifouling resistance to the membrane. Fouling behavior was also interpreted in terms of the topographical effect depending on the relative size of foulants to the pattern dimension. In addition, computational fluid dynamics simulation suggests that the enhanced antifouling of the patterned membrane is attributed to the enhancement in overall and local shear stress at the fluid-TiO₂ pattern interface.