Glutaraldehyde-crosslinking for improved copper absorption selectivity and chemical stability of polyethyleneimine coatings

Application of nano remediation of mine polluted in acid mine drainage water using machine learning model

Acid mine drainage (AMD) is the term used to describe drainage from coal mines with high sulfur-bearing rocks. The oxidative weathering of metal sulfides leads to AMD. The acidic environment corrodes more harmful compounds in the soil, which is spread throughout the working area. One such significant metal is copper, which is extracted in massive quantities from ores rich in sulfide. A copper-extraction resin might be created by combining diatomaceous earth (DE) particles with polyethyleneimine (PEI), which is shown to have great selectivity and affinity for copper. In this effort, PEI-DE particles' copper absorption level was examined by using synthetic and actual acid mine drainage samples at varied pH values. The findings of the copper uptake particles have been examined through the Support Vector Machine (SVM) model. Using the n-fold 14 cross-validation approach, the quantities of parameters and C are estimated to be 0.001 and 0.01, respectively. The SVM analysis was correct, and the findings indicated that copper could bind to the material efficiently and preferentially at pH 4. Subsequent water elution studies at a pH value of 1 confirmed the pH-reliant interaction between dissolved Cu and PEI by demonstrating full release of the adsorbed Cu. In this research, the copper absorption of PEI-DE particles from synthetic and genuine AMD specimens was studied based on several pH conditions. The findings suggest that copper may attach to the material effectively and preferentially at pH 4. Studies of filtering water at pH1 later confirmed that all of the adsorbed Cu was released. This shows that the interaction between PEI and dissolved Cu depends on PH.

Contact-Active Layer-by-Layer Grafted TPU/PDMS Blends as an Antiencrustation and Antibacterial Platform for Next-Generation Urological Biomaterials: Validation in Artificial and Human Urine

Urinary tract infections and urinary encrustation impede the long-term clinical performance of urological implants and medical devices. Together, biofilm formation and encrustation constitute serious complications, driving the development of next-generation urological biomaterials. The currently available bioengineered solutions have limited success during long-term usage in the urinary environment. In addressing this unmet clinical challenge, contact-active, antiencrustation surface grafting were conceived onto a dynamically cross-linked polydimethylsiloxane (PDMS) modified thermoplastic polyurethane (TPU) blend using the layer-by-layer (LbL) assembly route. To the best of the authors' knowledge, the present study is the first to investigate the LbL grafting in developing an antiencrustation platform. These multilayered assemblies strategically employed covalent cross-linking and electrostatic interaction-assisted progressive depositions of branched polyethyleneimine and poly(2-ethyl-2-oxazoline). While polyethyleneimine conferred the contact-killing bactericidal activity, the much-coveted antiencrustation properties were rendered by incorporating a partially hydrolyzed derivative of poly(2-ethyl-2-oxazoline). The performance of the resultant surface-modified TPU/PDMS blends was benchmarked against the conventional urological alloplasts, in a customized lab-scale bioreactor-based dynamic encrustation study and in human urine. After 6 weeks of exposure to an artificial urine medium, simulating urease-positive bacterial infection, the surface-modified blends exhibited a remarkable ability to suppress Ca and Mg encrustation. In addition, these blends also displayed superior grafting stability and antibacterial efficacy against common uropathogens. As high as 4-fold log reduction in the planktonic growth of Gram-negative P. mirabilis and Gram-positive MRSA was recorded with the LbL platform vis-à-vis medical-grade TPU. In conjunction, the in vitro cellular assessment with human keratinocytes (HaCaT) and human embryonic kidney cells (HEK) established the uncompromised cytocompatibility of the multilayered grafted blends. Finally, the physiologically relevant functionality of the LbL grafting has been validated using clinical samples of human urine collected from 129 patients with a broad spectrum of disease conditions. The phase-I pre-clinical study, entailing 6 week-long incubation in human urine, demonstrated significantly improved encrustation resistance of the blends. The collective findings of the present work clearly establish the success of LbL strategies in the development of stable, multifunctional new-generation urological biomaterials.

Real-time detection of copper contaminants in environmental water using porous silicon Fabry-Pérot interferometers

Water sources are vulnerable to intentional and inadvertent human pollution with thousands of synthetic and geogenic trace contaminants, posing long-term effects on the aquatic ecosystem and human health. Thus, early and rapid detection of water pollutants followed by corrective and preventive actions can lead to the reduction of the overall polluting impact to safeguard public health. This study presents a generic sensing assay for the label-free detection of copper contaminants in environmental water samples using multilayered polyethylenimine (PEI) functionalized porous silicon Fabry-Pérot interferometers. The selective chelating activity of PEI thin-films was monitored in real-time by reflective interferometric Fourier transform spectroscopy (RIFTS) while assessing the improved optical responses. The optimized scaffold of two sequential PEI layers depicted a linear working range between 0.2 and 2 ppm while presenting a detection limit of 0.053 ppm (53 ppb). The specificity of the developed platform was cross-validated against various metallic pollutants and cations commonly found in water bodies (i.e., Cd2+, Pb2+, Cr3+, Fe3+, Mg2+, Ca2+, Zn2+, K+ and Al3+). Finally, as a proof of concept, the analytical performance of the porous interferometers for real-life scenarios was demonstrated in three water samples (tap, ground and irrigation), presenting sufficient adaptability to complex matrix analysis with recovery values of 85-106%. Overall, the developed sensing concept offers an efficient, rapid and label-free methodology that can be potentially adopted for routine on-site detection using a simple and portable device.

Defect-Free Mechanical Graphene Transfer Using n-Doping Adhesive Gel Buffer

The synthesis of uniform low-defect graphene on a catalytic metal substrate is getting closer to the industrial level. However, its practical application is still challenging due to the lack of an appropriate method for its scalable damage-free transfer to a device substrate. Here, an efficient approach for a defect-free, etchant-free, wrinkle-free, and large-area graphene transfer is demonstrated by exploiting a multifunctional viscoelastic polymer gel as a simultaneous shock-free adhesive and dopant layer. Initially, an amine-rich polymer solution in its liquid form allows for conformal coating on a graphene layer grown on a Cu substrate. The subsequent thermally cured soft gel enables the shock-free and wrinkle-free direct mechanical exfoliation of graphene from a substrate due to its strong charge-transfer interaction with graphene and excellent shock absorption. The adhesive gel with a high optical transparency works as an electron doping layer toward graphene, which exhibits significantly reduced sheet resistances without optical transmittance loss. Lastly, the transferred graphene layer shows high mechanical and chemical stabilities under the repeated bending test and exposure to various solvents. This gel-assisted mechanical transfer method can be a solution to connect the missing part between large-scale graphene synthesis and next-generation electronics and optoelectronic applications.

Cyclic Copper Uptake and Release from Natural Seawater-A Fully Sustainable Antifouling Technique to Prevent Marine Growth

Unwanted growth of fouling organisms on underwater surfaces is an omnipresent challenge for the marine industry, costing billions of dollars every year in the transportation sector alone. Copper, the most widely used biocide in antifouling paints, is at the brink of a total ban in being used in antifouling coatings, as it has become an existential threat to nontargeted species due to anthropogenic copper inputs into protected waters. In the current study, using a porous and cross-linked poly(ethylene imine) structure under marine and fouling environments, available copper from natural seawater was absorbed and electrochemically released back as a potent biocide at 1.3 V vs Ag|AgCl, reducing marine growth by 94% compared to the control electrode (coupon) at 0 V. The coating can also function as an electrochemical copper sensor enabling real-time monitoring of the electrochemical uptake and release of copper ions from natural seawater. This allows tailoring of the electrochemical program to the changing marine environments, i.e., when the vessels move from high-copper-contaminated waters to coastal regions with low concentrations of copper.

Removal and Separation of Heavy Metal Ions from Multicomponent Simulated Waters Using Silica/Polyethyleneimine Composite Microparticles

Composite solid surfaces with high content of functional groups (FGs) are useful materials in different types of applications requiring stimuli-responsive "hard/soft" architectures, their improved properties rising from the combination of organic-inorganic parts. Among different types of weak polyelectrolytes, poly(ethyleneimine) (PEI) is of great interest in the construction of composite systems with thin layer-by-layer (LbL) organic films due to the large number of amino groups per unit mass of polymer. Herein, the spherical silica microparticles were modified with linear (L) or branched (B) PEI chains using LbL deposition of a copper complex (PEIL-Cu²⁺ or PEIB-Cu²⁺) and poly(acrylic acid) (PAA), glutaraldehyde selective cross-linking, followed by copper and PAA extraction from the multilayer. The newly formed silica/(PEIL)₁₀ and silica/(PEIB)₁₀ composites were used in batch and column sorption/desorption experiments of four heavy metal ions (Cu²⁺, Ni²⁺, Co²⁺, and Cd²⁺). In noncompetitive conditions ([FG]/Σ[M²⁺] > 9), all heavy metal ions were retained on composites, demonstrating the potential application of the prepared functional microparticles in surface water treatment. However, in competitive conditions ([FG]/Σ[M²⁺] < 9), only Cu²⁺ is sorbed in high amount (∼2.5 mmol·g^-1 PEI) on composites, with simultaneous displacement of already sorbed ions, demonstrating the solid-phase extraction and chromatographic properties of the synthesized silica/(PEIL)_n and silica/(PEIB)_n composites.

Selenium(VI) and copper(II) adsorption using polyethyleneimine-based resins: Effect of glutaraldehyde crosslinking and storage condition

This study synthesizes polyethyleneimine-glutaraldehyde (PEI-GA) resins using different amounts of GA to crosslink with a certain amount of PEI and compares these adsorbents for the adsorption of Cu(II) (cations) and Se(VI) (anions). Moreover, the stability of adsorption affinity of PEI-GA resins stored in open or sealed conditions is also studied. Results show that the amount of GA for PEI crosslinking does not affect the adsorption performance for Se(VI), especially when PEI/GA mass ratio is less than 2, while for Cu(II), the increase on GA amount decreases Cu(II) adsorption capacity. This difference is directly correlated to the change in the adsorption mechanism from electrostatic attraction to chelation. The primary and secondary amine groups on PEI can easily react with CO₂ in the air to form carbamate, potentially affecting the adsorption performance of PEI. Results also indicate that the adsorption efficiency for Se(VI) is hardly affected by the storage condition, while that for Cu(II) decreases significantly after 20-day storage compared to the freshly prepared ones. In addition, all of the adsorbents can selectively remove Se(VI) from Se(VI)-As(V) system and Cu(II) from Pb(II)-Cu(II) system, indicating that the crosslinking has no significant influence on the selectivity.

Multiplatform Protein Detection and Quantification Using Glutaraldehyde-Induced Fluorescence for 3D Systems

Glutaraldehyde (GTA) is a dialdehyde used as biological fixative and its interaction with proteins like bovine serum albumin (BSA) has been well described. Additionally, GTA is known to induce fluorescence when interacting with BSA molecules. In this work, it is developed a new sensitive and reproducible method for BSA quantification using GTA crosslinking to endow fluorescence to BSA molecules. This method can be used with standard lab equipment, providing a low cost, fast-tracking and straightforward approach for BSA quantification. Techniques such as confocal laser scanning microscopy (CLSM) and spectrofluorometry are applied for quantitative assessment, and widefield fluorescence microscopy for qualitative assessment. Qualitative and quantitative correlations between BSA content and GTA-induced fluorescence are verified. BSA concentrations as low as 62.5 μg/mL are detected using CLSM. This method can be highly advantageous for protein quantification in three-dimensional hydrogel systems, specially to evaluate protein loading/release in protein delivery or molecular imprinting systems. Graphical Abstract Preparation and analysis of glutaraldehyde-induced protein-fluorescence in 3D hydrogels. Alginate-methacrylate hydrogels containing varying amounts of bovine serum albumin (BSA) are prepared by photopolymerization and then incubated in glutaraldehyde solutions. Samples observation is performed using confocal laser scanning microscopy, spectrofluorometry and widefield fluorescence microscopy. Data is processed and retrieves a quantitative correlation between protein content and fluorescence levels.

Environmental Copper Sensor Based on Polyethylenimine-Functionalized Nanoporous Anodic Alumina Interferometers

Anthropogenic copper pollution of environmental waters from sources such as acid mine drainage, antifouling paints, and industrial waste discharge is a major threat to our environment and human health. This study presents an optical sensing system that combines self-assembled glutaraldehyde-cross-linked double-layered polyethylenimine (PEI-GA-PEI)-modified nanoporous anodic alumina (NAA) interferometers with reflectometric interference spectroscopy (RIfS) for label-free, selective monitoring of ionic copper in environmental waters. Calibration of the sensing system with analytical solutions of copper shows a linear working range between 1 and 100 mg L-1, and a low limit of detection of 0.007 ± 0.001 mg L-1 (i.e., ∼0.007 ppm). Changes in the effective optical thickness (ΔOTeff) of PEI-GA-PEI-functionalized NAA interferometers are monitored in real-time by RIfS, and correlated with the amount of ionic copper present in aqueous solutions. The system performance is validated through X-ray photoelectron spectroscopy (XPS) and the spatial distribution of copper within the nanoporous films is characterized by time-of-flight-secondary ion mass spectroscopy (TOF-SIMS). The specificity and chemical selectivity of the PEI-GA-PEI-NAA sensor to Cu2+ ions is verified by screening six different metal ion solutions containing potentially interfering ions such as Al3+, Cd2+, Fe3+, Pb2+, Ni2+, and Zn2+. Finally, the performance of the PEI-GA-PEI-NAA sensor for real-life applications is demonstrated using legacy acid mine drainage liquid and tap water for qualitative and quantitative detection of copper ions. This study provides new opportunities to develop portable, cost-competitive, and ultrasensitive sensing systems for real-life environmental applications.

Neutron scattering in the biological sciences: progress and prospects

The scattering of neutrons can be used to provide information on the structure and dynamics of biological systems on multiple length and time scales. Pursuant to a National Science Foundation-funded workshop in February 2018, recent developments in this field are reviewed here, as well as future prospects that can be expected given recent advances in sources, instrumentation and computational power and methods. Crystallography, solution scattering, dynamics, membranes, labeling and imaging are examined. For the extraction of maximum information, the incorporation of judicious specific deuterium labeling, the integration of several types of experiment, and interpretation using high-performance computer simulation models are often found to be particularly powerful.

Copper removal from acid mine drainage-polluted water using glutaraldehyde-polyethyleneimine modified diatomaceous earth particles

Mine waters and tailings generated from mining and mineral processing activities often have detrimental impact on the local environment. One example is acid mine drainage, in which sulphides in the mining waste react with water and oxygen to produce an acidic environment that subsequently dissolves host rock minerals from the waste containing toxic metals and trace elements. Copper is one such metal of significance, as it is mined at large volumes in sulphide containing ores. It has strong biocidal activity that greatly affects ecosystems. We have previously reported that glutaraldehyde (GA)-crosslinked polyethyleneimine (PEI) has strong affinity and selectivity for copper and that diatomaceous earth (DE) particles can be modified with the material to form a copper-extraction resin. In this study, the copper uptake of GA-PEI-DE particles was investigated from synthetic and real acid mine drainage samples under different pHs and their copper removal performance was compared with that of selected commercial resins. The results revealed that copper could effectively and preferentially bind to the material at pH 4, and that the copper could be completely eluted by lowering of the pH. In addition, effective copper uptake and elution was demonstrated using real legacy acid mine drainage water from Mount Lyell in Tasmania.

Bio-template assisted synthesis of porous glutaraldehyde-polyethyleneimine particulate resin for selective copper ion binding and recovery

Porous ion-exchange resins with features of high selectivity, high capacity, fast adsorption kinetics and chemical stability over a wide pH range are attractive for extracting precious metals like copper and upcycling waste. In this study, porous glutaraldehyde-polyethyleneimine (GA-PEI) particulate resin was synthesised using diatomaceous earth (DE) particles as a bio-template. The crosslinking of PEI by GA was successfully conducted on the surface of DE. Removal of the template DE, merely by chemical etching with potassium hydroxide, resulted in the porous GA-PEI particulate resin. The resin showed excellent selectivity for copper ions in binding and recovery from solutions as complex as real legacy acid mine drainage liquid. The copper ion uptake capacity of the GA-PEI resin was determined to be >8 times greater than non-etched GA-PEI-DE particles. Under the investigated conditions, the GA-PEI resin showed higher selectivity to copper ions from real legacy acid mine drainage liquid compared to the commercial resins Purolite S930 Plus and Lewatit TP 220. Importantly, the absorbed copper ions could be released by simply adjusting pH of the solution to 1. For uptake from acid mine drainage liquid at pH 4 and elution at pH 1, purer copper solutions were achieved with GA-PEI compared to Purolite S930 Plus or Lewatit TP 220 following two cycles of iteration. The results indicate the great potential for using the porous GA-PEI resin in copper extraction under real-world conditions.

Porous ion-exchange resins with features of high selectivity, high capacity, fast adsorption kinetics and chemical stability over a wide pH range are attractive for extracting precious metals like copper and upcycling waste.

Unhindered copper uptake by glutaraldehyde-polyethyleneimine coatings in an artificial seawater model system with adsorbed swollen polysaccharides and competing ligand EDTA

Shortly after a surface is submerged in the sea, a conditioning film is generally formed by adsorption of organic molecules, such as polysaccharides. This could affect transport of molecules and ions between the seawater and the surface. An artificial seawater model system was developed to understand how adsorbed polysaccharides impact copper binding by glutaraldehyde-crosslinked polyethyleneimine coatings. Coating performance was also determined when competed against copper-chelating EDTA. Polysaccharide adsorption and copper binding and distribution were investigated using advanced analytical techniques, including depth-resolved time-of-flight secondary ion mass spectroscopy, grazing incidence X-ray absorption near-edge spectroscopy, quartz crystal microbalance with dissipation monitoring and X-ray photoelectron spectroscopy. In artificial seawater, the polysaccharides adsorbed in a swollen state that copper readily penetrated and the glutaraldehyde-polyethyleneimine coatings outcompeted EDTA for copper binding. Furthermore, the depth distribution of copper species was determined with nanometre precision. The results are highly relevant for copper-binding and copper-releasing materials in seawater.