Polytriazole polyether elastomers with widely tunable mechanical properties: The role of network structure and crystallization behavior

Study on Mechanical Properties of Polyurethane Cross-Linked P(E-co-T)/PEG Blended Polyether Elastomer

To improve the mechanical properties of polyurethane cross-linked poly (ethylene oxide-co-tetrahydrofuran) (P(E-co-T)) elastomers at room temperature, using poly (ethylene oxide-co-tetrahydrofuran) and high-molecular-weight polyethylene glycol (PEG) as raw materials and polyisocyanate N100 as curing agent, a series of polyurethane cross-linked blended polyether elastomers were prepared by changing the elastomer-curing parameter R value (n(-NCO)/n(-OH)) and P(E-co-T)/PEG ratio. Equilibrium swelling measurements showed that the chemical cross-linkage of the elastomers tended to decrease with the decreasing R value, the average molecular weight (Mc) of the network chain increased, and the density of the network chain (N0) decreased. Wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC) tests showed that PEG chain segments within the elastomers crystallized at room temperature, while the crystallinity increased with decreasing R value and increasing PEG content. The mechanical property tests showed that the elongation at break tended to decrease with increasing R value; the tensile strength first increased and then decreased. At R value 0.9, the elastomer presented good comprehensive mechanical properties. In addition, the mechanical properties of polyurethane cross-linked P(E-co-T)/PEG blended polyether elastomer showed an increasing trend with the increase in PEG content when the curing parameter of 0.9 remained unchanged.

Curing Behaviors of Alkynyl-Terminated Copolyether with Glycidyl Azide Polymer in Energetic Plasticizers

Alkynyl-terminated polyethylene oxide−tetrahydrofuran (ATPET) and glycidyl azide polymer (GAP) could be linked through click-chemistry between the alkynyl and azide, and the product may serve a binder for solid propellants. The effects of the energetic plasticizers A3 [1:1 mixture of bis-(2,2-dinitropropy) acetal (BDNPA) and bis-(2,2-dinitropropyl) formal(BDNPN)] and Bu-NENA [N-butyl-N-(2nitroxyethyl) nitramine] on the curing reaction between ATPET and GAP have been studied. A diffusion-ordered nuclear magnetic resonance spectroscopy (DOSY-NMR) approach has been used to monitor the change in the diffusion coefficient of cross-linked polytriazole polyethylene oxide−tetrahydrofuran (PTPET). The change in the diffusion coefficient of PTPET with A3 plasticizer is significantly higher than that of PTPET with Bu-NENA. Viscosity analysis further highlighted the difference between A3 and Bu-NENA in the curing process—the curing curve of PTPET (A3) with time can be divided into two stages, with an inflection point being observed on the fourth day. For PTPET (Bu-NENA), in contrast, only one stage is seen. The above methods, together with gel permeation chromatography (GPC) analysis, revealed distinct effects of A3 and Bu-NENA on the curing process of PTPET. X-ray Photoelectron Spectroscopy (XPS) analysis showed that Bu-NENA has little effect on the valence oxidation of copper in the catalyst. Thermogravimetric (TG) analysis indicated that Bu-NENA helps to improve the thermal stability of the catalyst. After analysis of several possible factors by means of XPS, modeling with Material Studio and TG, the formation of molecular cages between Bu-NENA and copper is considered to be the reason for the above differences. In this article, GAP (Mn = 4000 g/mol) was used to replace GAP (Mn = 427 g/mol) to successfully synthesize the PTPET elastomer with Bu-NENA plasticizer. Mechanical data measured for the PTPET (Bu-NENA) sample included ε = 34.26 ± 2.98%, and σ = 0.198 ± 0.015 MPa.

The Effect of Glycidyl Azide Polymer Grafted Tetrafunctional Isocyanate on Polytriazole Polyethylene Oxide-Tetrahydrofuran Elastomer and its Propellant Properties

A new energetic curing reagent, Glycidyl azide polymer grafted tetrafunctional isocyanate (N100-g-GAP) was synthesized and characterized by FT-IR and GPC approaches. Polytriazole polyethylene oxide-tetrahydrofuran (PTPET) elastomer was prepared by N100-g-GAP and alkynyl terminated polyethylene oxide-tetrahydrofuran (ATPET). The resulting PTPET elastomer was fully characterized by TGA, DMA, FTIR and mechanical test. The above analysis indicates that PTPET elastomers using N100-g-GAP as curing reagent have the potential for use in propellants. The overall formulation test of the composite propellants shows that this curing system can effectively enhance mechanical strength and bring a significant improvement in the interface interaction between the RDX & AP particles and binder matrix.