Fabrication of porous three-dimensional fibroin structures through a freezing process: Research Article

Modulation of Biophysical Cues in Nature Inspired Patterning of Porous Silk Fibroin Scaffold for Replenishable Controlled Drug Delivery

While a sticking plasteris enough for healing of most of the minor cuts they may get routinely, critical situations like surgical, gunshot, accidental or diabetic wounds;lacarations and other cutaneous deep cuts may require implants and simultaneous medications for healing. From the biophysical standpoint, an internal force-based physical surface stimulusis crucial for cellular sensing during wound repair. In this paper, the authors report the fabrication of a porous, biomimmetically patterned silk fibroin scaffold loaded with ampicillin, which exhibits controlled release of the drug along with possible replenishment of the same. In vitro swelling study reveals that the scaffolds with hierarchical surface patterns exhibit lower swelling and degradation than other types of scaffolds. The scaffolds, that show remarkable broad-spectrum antibacterial efficacy, exhibit Korsemeyer-Peppas model for the ampicillin release patterns due to the structural hydrophobicity imparted by the patterns. Four distinct cell-matrix adhesion regimes are investigated for the fibroblasts to eventually form cell sheets all over the hierarchical surface structures. 4',6-diamidino-2-phenylindole (DAPI) and Fluorescein Diacetate (FDA) fluorescent staining clearly demonstrate the superiority of patterned surface over its other variants. A comparative immunofluorescence study among collagen I, vinculin, and vimentin expressions substantiated the patterned surface to be superior to others.

Improving the performance of coupled solid carbon source biofilm carriers through pore-forming methods

Coupled solid carbon source biofilm carriers (CCBs) was usually utilized to enhance the treatment efficiency of low carbon/nitrogen (C/N) wastewater. However, current CCBs have low carbon release capacity because of its small inner mass transfer coefficient. Therefore, this study innovatively applied pore-forming methods to modify CCBs. After orthogonal selections, two porous CCBs, which were respectively prepared through circulating freezing pore-forming method (CCB2) and ammonium bicarbonate pore-forming method (CCB3), were proposed and further applied in sequencing batch moving bed biofilm reactors (SBMBBRs). The results indicated that circulating freezing pore-forming method could improve the mechanical strength and carbon source release rate of CCBs. In addition, CCB2 could significantly enhance the total nitrogen (TN) removal efficiency of SBMBBRs, when compared with the non-porous CCBs (i.e., CCB1). Further biofilm and simultaneous nitrification and denitrification (SND) rate calculation attributed this enhancement to the higher biofilm amount (i.e., 0.06 g g^-1 CCB) and the higher SND rate (i.e., 33.60%). Microbial community analysis reiterated these observations that CCB2 and CCB3 could accumulate Proteobacteria, Actinobacteriota and Nitrospirota, and also stimulate nitrification and denitrification associated pathways. More importantly, the cost calculation indicated CCB2 cost only 47.37% of CCB1 and 31.34% of CCB3, showing highly economic applicability. Overall, our results collectively proved that CCBs manufactured by circulating freezing pore-forming method could provide more carbon releasing points and microorganisms attaching positions, exhibiting effectively nitrogen removal when treating low C/N wastewater.

Seeking Solvation: Exploring the Role of Protein Hydration in Silk Gelation

The mechanism by which arthropods (e.g., spiders and many insects) can produce silk fibres from an aqueous protein (fibroin) solution has remained elusive, despite much scientific investigation. In this work, we used several techniques to explore the role of a hydration shell bound to the fibroin in native silk feedstock (NSF) from Bombyx mori silkworms. Small angle X-ray and dynamic light scattering (SAXS and DLS) revealed a coil size (radius of gyration or hydrodynamic radius) around 12 nm, providing considerable scope for hydration. Aggregation in dilute aqueous solution was observed above 65 °C, matching the gelation temperature of more concentrated solutions and suggesting that the strength of interaction with the solvent (i.e., water) was the dominant factor. Infrared (IR) spectroscopy indicated decreasing hydration as the temperature was raised, with similar changes in hydration following gelation by freezing or heating. It was found that the solubility of fibroin in water or aqueous salt solutions could be described well by a relatively simple thermodynamic model for the stability of the protein hydration shell, which suggests that the affected water is enthalpically favoured but entropically penalised, due to its reduced (vibrational or translational) dynamics. Moreover, while the majority of this investigation used fibroin from B. mori, comparisons with published work on silk proteins from other silkworms and spiders, globular proteins and peptide model systems suggest that our findings may be of much wider significance.

Status of Plant Protein-Based Green Scaffolds for Regenerative Medicine Applications

In recent decades, regenerative medicine has merited substantial attention from scientific and research communities. One of the essential requirements for this new strategy in medicine is the production of biocompatible and biodegradable scaffolds with desirable geometric structures and mechanical properties. Despite such promise, it appears that regenerative medicine is the last field to embrace green, or environmentally-friendly, processes, as many traditional tissue engineering materials employ toxic solvents and polymers that are clearly not environmentally friendly. Scaffolds fabricated from plant proteins (for example, zein, soy protein, and wheat gluten), possess proper mechanical properties, remarkable biocompatibility and aqueous stability which make them appropriate green biomaterials for regenerative medicine applications. The use of plant-derived proteins in regenerative medicine has been especially inspired by green medicine, which is the use of environmentally friendly materials in medicine. In the current review paper, the literature is reviewed and summarized for the applicability of plant proteins as biopolymer materials for several green regenerative medicine and tissue engineering applications.

Scaffolding Strategies for Tissue Engineering and Regenerative Medicine Applications

During the past two decades, tissue engineering and the regenerative medicine field have invested in the regeneration and reconstruction of pathologically altered tissues, such as cartilage, bone, skin, heart valves, nerves and tendons, and many others. The 3D structured scaffolds and hydrogels alone or combined with bioactive molecules or genes and cells are able to guide the development of functional engineered tissues, and provide mechanical support during in vivo implantation. Naturally derived and synthetic polymers, bioresorbable inorganic materials, and respective hybrids, and decellularized tissue have been considered as scaffolding biomaterials, owing to their boosted structural, mechanical, and biological properties. A diversity of biomaterials, current treatment strategies, and emergent technologies used for 3D scaffolds and hydrogel processing, and the tissue-specific considerations for scaffolding for Tissue engineering (TE) purposes are herein highlighted and discussed in depth. The newest procedures focusing on the 3D behavior and multi-cellular interactions of native tissues for further use for in vitro model processing are also outlined. Completed and ongoing preclinical research trials for TE applications using scaffolds and hydrogels, challenges, and future prospects of research in the regenerative medicine field are also presented.

Preparation of hydroxylated lecithin complexed iodine/carboxymethyl chitosan/sodium alginate composite membrane by microwave drying and its applications in infected burn wound treatment

Improving the antibacterial properties of membrane wound dressings of natural polymers is crucial. Iodine is an important safe inorganic antibacterial agent, but was confined in the composition with polymer membranes due to the challenges of homogeneity and stability during drying. In the present work, iodine was complexed with hydroxylated lecithin (HL) to improve its stability and complexing efficiency for the composition with carboxymethly chitosan/sodium alginate. With the aid of microwave drying, hydroxylated lecithin complexed iodine/carboxymethly chitosan/sodium alginate (HLI/CMCS/SA) composite membranes with homogeneously distributions of HLI, high contents of activated iodine, good mechanical and swelling properties, proper water vapor permeability, pH controllable iodine release and excellent antibacterial properties were prepared. The composite membranes exhibited high repairing efficiencies for the infection of a rat model of the seawater immersed wound infection of deep partial-thickness burns. This novel antibacterial composite membrane can be potentially used as a high performance wound dressing for treating and repairing open trauma infections.