Conformational transitions of solubilized trout elastins

The effects of heating on the mechanical properties of arterial elastin

Autoclaving is a standard way of purifying arterial elastin for mechanical testing, but recent evidence suggests that heating native elastin might affect its mechanical behavior. We therefore examined the quasi-static tensile properties of pig arterial tissue to see if the mechanical properties of native elastin are altered by autoclaving. From an analysis of the shapes of the stress-extension ratio curves of tissues before and after 8 h of autoclaving, we determined that the mechanical characteristics of elastin dominated the behavior of unautoclaved arterial tissue at wall stresses around 25+/-5 kPa. Autoclaving did not change the tangential modulus of the tissue at this wall stress (+/-4% 95% CI), indicating that elastin can be heated during purification without affecting its mechanical behavior. Autoclaved tissue was tested daily to determine the effects of prolonged heating of autoclaved elastin. Between tests the elastin was incubated at either 80 degrees C (experimental group) or 37 degrees C (control group). After 6 days the average modulus of the control group was unchanged from the initial value, while the average modulus of the experimental group was 7%+/-2% (95% CI) lower. At shorter times the modulus of the experimental group was not significantly reduced. The slight decrease in modulus suggests a slow chemical degradation may occur with prolonged heating, but its time course and magnitude are such that it would not affect standard mechanical tests.

Solid-state studies on synthetic fragments and analogues of elastin

A series of synthetic fragments and analogues of elastin have been investigated, in the solid state, by means of differential scanning calorimetry and thermally stimulated current. Most of the polypeptides were shown to possess both amorphous regions and segments of long-range order. Water, which interacts preferentially with the amorphous zones, behaves as plasticizer, i.e. facilitates the localized motions of polypeptide chains. The results obtained have been correlated with elastin elasticity, in particular as far as the fundamental destructuring role of water is concerned.

Spectroscopic studies on elastin-like synthetic polypeptides

Spectroscopic studies on synthetic polypeptides containing the unit-X-G-G (X=V or L) are reported. The sequences, constituting either fragments or model of elastin, were shown to adopt type II beta-turns together with an ensemble of unordered conformations. Furthermore, it was found that the stability of the beta-turns was depending on the nature of the X residue, on the hydration of the chain and, in the case of the sequence G-V-G-G-L, was decreasing by increasing the length of the chain.

Synthetic fragments and analogues of elastin. II. Conformational studies

Conformational studies on synthetic repetitive sequences and analogues of elastin are described. CD and nmr measurements gave evidence of flexible beta-turns as the dominant structural feature whose stability was found to decrease by increasing the number of repetitive units. The sequences comprised the structural unit Gly-X-Gly (X = Val, Leu, Ala), with X-Gly or Gly-Gly located at the corners of the bend. Based on that, it is proposed that these regions of elastin, unlike the proline-containing sequences, contribute to the elasticity of the protein through a classical mechanism in terms of the rotational isomeric state theory.

Synthetic fragments and analogues of elastin. I. The synthesis

The synthesis of some repetitive sequences of elastin and their simplified analogues, all comprising the structural unit Gly-X-Gly (X = Val, Leu, Ala), is described. In particular, the following peptides and polypeptides were synthesized and characterized: Boc-Gly-Val-Gly-Gly-Leu-OMe, Boc-Gly-Leu-Gly-Gly-Val-OMe, Boc-(Gly-Val-Gly-Gly-Leu)2-OMe, Boc-(Gly-Val-Gly-Gly-Leu)3-OMe, Boc-Gly-Val-Gly-Gly-OEt, Boc-Leu-Gly-Gly-Leu-OMe, Boc-Val-Gly-Gly-Val-OMe, poly(Ala-Gly-Gly), poly(Val-Gly-Gly), and poly(Leu-Gly-Gly). In every case, the synthesis was accomplished by classical procedures in solution, by using the p-nitrophenyl ester method for the polycondensation step, and the mixed anhydride or the azide methods for the coupling steps.

Nuclear Overhauser effect and computational characterization of the beta-spiral of the polypentapeptide of elastin

The structure of the elastin polypentapeptide, poly(VPGVG), was studied by nuclear Overhauser effect experiments using perdeuterated Val1 and Val4 samples under the condition where intermolecular interactions are absent. More extensive interaction was found between the Val1 gamma CH and Pro2 beta CH protons than between the Val4 gamma CH and Pro2 beta CH protons. The Val1 gamma CH3-Pro2 beta CH interaction does not occur within the same pentamer as previously shown experimentally and as expected from steric considerations. The results are incompatible with the presence of a random chain network in poly(VPGVG) at room temperature but are readily explicable in terms of interturn interactions in a beta-spiral structure. More specifically, the results indicate that the beta-spiral conformation with 2.9 pentamers/turn is more prevalent than that with 2.7 pentamers/turn. Using conformations developed by molecular mechanics calculations, molecular dynamics simulations were carried out to compare the relative energies of these two variants of this class of beta-spiral structures. It was found in vacuo that the structure with 2.9 pentamers/turn is indeed more stable than that of 2.7 pentamers/turn by approximately 1 kcal/mole-pentamer.