High-Performance Carbon Anode Derived from Sugarcane for Packed Microbial Fuel Cells

Graphitized mango seed as an effective 3D anode in batch and continuous mode microbial fuel cells for sustainable wastewater treatment and power generation

Herein, we explored the utilization of graphitized mango seeds as 3D-packed anodes in microbial fuel cells (MFCs) powered by sewage wastewater. Mango seeds were graphitized at different temperatures (800 °C, 900 °C, 1000 °C, and 1100 °C) and their effectiveness as anodes was evaluated. Surface morphology analysis indicated that the proposed anode was characterized by layered branches and micro-sized deep holes, facilitating enhanced biofilm formation and microorganism attachment. Maximum power densities achieved in the MFCs utilizing the mango seed-packed anodes graphitized at 1100 °C and 1000 °C were 2170.8 ± 90 and 1350.6 ± 125 mW m-2, respectively. Furthermore, the weight of the graphitized seed anode demonstrated a positive correlation with the generated power density and cell potential. Specifically, MFCs fabricated with 9 g and 6 g anodes achieved maximum power densities of 2170.8 ± 90 and 1800.5 ± 40 mW m-2, respectively. A continuous mode air cathode MFC employing the proposed graphitized mango anode prepared at 1100 °C and operated at a flow rate of 2 L h-1 generated a stable current density of approximately 12 A m-2 after 15 hours of operation, maintaining its stability for 75 hours. Furthermore, a chemical oxygen demand (COD) removal efficiency of 85% was achieved in an assembled continuous mode MFC. Considering that the proposed MFC was driven by sewage wastewater without the addition of external microorganisms, atmospheric oxygen was used as the electron acceptor through an air cathode mode, agricultural biomass waste was employed for the preparation of the anode, and a higher power density was achieved (2170.8 mW m-2) compared to reported values; it is evident that the proposed graphitized mango seed anode exhibits high efficiency for application in MFCs.

Performance analysis of microbial fuel cell - membrane bioreactor with reduced graphene oxide enhanced polypyrrole conductive ceramic membrane: Wastewater treatment, membrane fouling and microbial community under high salinity

The application of membrane bioreactor (MBR) in high salinity wastewater treatment was mainly hindered by membrane fouling. Microbial fuel cell (MFC)-MBR coupling system was established to alleviate membrane fouling and save energy. Reduced graphene oxide/polypyrrole ceramic membrane (rGO/PPy CM) with high conductivity and stability was innovatively placed in MFC-MBRs as both cathode and filter, with PPy CM, rGO/PPy CM and CM placed in other reactors. MFC-MBR (rGO/PPy) and MFC-MBR (PPy) achieved higher pollutant removal efficiencies (90.73 % and 90.45 % for TOC, 87.22 % and 86.56 % for NH4+-N, respectively) and superior anti-fouling performance (1.86 and 1.93 kPa/d for average membrane fouling rates) than both conventional MBRs (CMBRs). The stable voltage generation was around 287 and 242 mV, respectively. Through high throughput sequencing, electric field showed a positive correlation with the abundance and activity of most dominant phylum (Bacteroidetes, Chloroflexi, Actinobacteria, and Firmicutes) and functional genes (amoA, hao, narG, napA, nirK, norB, and nosZ), thereby improving pollutant removal efficiency. The higher conductivity of rGO/PPy CM resulted in enhanced electric field intensity, leading to superior performance of anti-fouling and pollutant removal. This study inventively explored the effects of conductive membrane property on electricity generation performance, microbial community, pollutant removal and membrane fouling, providing theoretical support for the selection of electrode materials in MFC-MBR.

Synergistic advancements in sewage-driven microbial fuel cells: novel carbon nanotube cathodes and biomass-derived anodes for efficient renewable energy generation and wastewater treatment

Microbial fuel cells (MFCs) offer a dual solution of generating electrical energy from organic pollutants-laden wastewater while treating it. This study focuses on enhancing MFC performance through innovative electrode design. Three-dimensional (3D) anodes, created from corncobs and mango seeds via controlled graphitization, achieved remarkable power densities. The newly developed electrode configurations were evaluated within sewage wastewater-driven MFCs without the introduction of external microorganisms or prior treatment of the wastewater. At 1,000°C and 1,100°C graphitization temperatures, corncob and mango seed anodes produced 1,963 and 2,171 mW/m2, respectively, nearly 20 times higher than conventional carbon cloth and paper anodes. An advanced cathode composed of an activated carbon-carbon nanotube composite was introduced, rivaling expensive platinum-based cathodes. By optimizing the thermal treatment temperature and carbon nanotube content of the proposed cathode, comparable or superior performance to standard Pt/C commercial cathodes was achieved. Specifically, MFCs assembled with corncob anode with the proposed and standard Pt/C cathodes reached power densities of 1,963.1 and 2,178.6 mW/m2, respectively. Similarly, when utilizing graphitized mango seeds at 1,100°C, power densities of 2,171 and 2,151 mW/m2 were achieved for the new and standard cathodes, respectively. Furthermore, in continuous operation with a flow rate of 2 L/h, impressive chemical oxygen demand (COD) removal rates of 77% and 85% were achieved with corncob and mango seed anodes, respectively. This work highlights the significance of electrode design for enhancing MFC efficiency in electricity generation and wastewater treatment.

Analysis and enhancement of the energy utilization efficiency of corn stover using strain Lsc-8 in a bioelectrochemical system

The strain Lsc-8 can produce a current density of 33.08 µA cm^-2 using carboxymethylcellulose (CMC) as a carbon source in a three-electrode configuration. A co-culture system of strain Lsc-8 and Geobacter sulfurreducens PCA was used to efficiently convert cellulose into electricity to improve the electricity generation capability of microbial fuel cells (MFCs). The maximum current density achieved by the co-culture with CMC was 559 μA cm^-2, which was much higher than that of strain Lsc-8 using CMC as the carbon source. The maximum power density reached 492.05 ± 52.63 mW cm^-2, which is much higher than that previously reported. Interaction mechanism studies showed that strain Lsc-8 had the ability to secrete riboflavin and convert cellulose into acetic acid, which might be the reason for the high electrical production performance of the co-culture system. In addition, to the best of our knowledge, a co-culture or single bacteria system using agricultural straw as the carbon source to generate electricity has not been reported. In this study, the maximum current density of the three-electrode system inoculated with strain Lsc-8 was 14.56 μA cm^-2 with raw corn stover as the sole carbon source. Raw corn stover as a carbon source was also investigated for use in a co-culture system. The maximum current density achieved by the co-culture was 592 μA cm^-2. The co-culture system showed a similar electricity generation capability when using raw corn stover and when using CMC. This research shows for the first time that a co-culture or single bacteria system can realize both waste biomass treatment and waste power generation.

Biomass-Derived Carbon Anode for High-Performance Microbial Fuel Cells

: Although microbial fuel cells (MFCs) have been developed over the past decade, they still have a low power production bottleneck for practical engineering due to the ineffective interfacial bioelectrochemical reaction between exoelectrogens and anode surfaces using traditional carbonaceous materials. Constructing anodes from biomass is an effective strategy to tackle the current challenges and improve the efficiency of MFCs. The advantage features of these materials come from the well-decorated aspect with an enriched functional group, the turbostratic nature, and porous structure, which is important to promote the electrocatalytic behavior of anodes in MFCs. In this review article, the three designs of biomass-derived carbon anodes based on their final products (i.e., biomass-derived nanocomposite carbons for anode surface modification, biomass-derived free-standing three-dimensional carbon anodes, and biomass-derived carbons for hybrid structured anodes) are highlighted. Next, the most frequently obtained carbon anode morphologies, characterizations, and the carbonization processes of biomass-derived MFC anodes were systematically reviewed. To conclude, the drawbacks and prospects for biomass-derived carbon anodes are suggested.

Carbon-Based Composites as Anodes for Microbial Fuel Cells: Recent Advances and Challenges

Owing to the low price, chemical stability and good conductivity, carbon-based materials have been extensively applied as the anode in microbial fuel cells (MFCs). In this review, apart from the charge storage mechanism and anode requirements, the major work focuses on five categories of carbon-based anode materials (traditional carbon, porous carbon, nano-carbon, metal/carbon composite and polymer/carbon composite). The relationship is demonstrated in depth between the physicochemical properties of the anode surface/interface/bulk (porosity, surface area, hydrophilicity, partical size, charge, roughness, etc.) and the bioelectrochemical performances (electron transfer, electrolyte diffusion, capacitance, toxicity, start-up time, current, power density, voltage, etc.). An outlook for future work is also proposed.

Steamed cake-derived 3D carbon foam with surface anchored carbon nanoparticles as freestanding anodes for high-performance microbial fuel cells

Anode design is highly significant for microbial fuel cells, since it simultaneously serves as the scaffold for electroactive microorganisms and as a medium for electron migration. In this study, a stiff 3D carbon foam with surface anchored nitrogen-containing carbon nanoparticles was facilely constructed via in-situ polyaniline coating of carbonized steamed cake prior to the carbonization process. The resultant product was determined to be an excellent freestanding anode that enabled the microbial fuel cell to deliver a maximum power density of up to 1307 mW/m², which significantly outperformed its non-coated counterpart, the widely used commercial carbon felt. Further investigations revealed that the overall performance enhancement was associated with the open porosity, enlarged electroactive surface, increased biocompatibility, and decreased electric resistance of the anode scaffold. This promising anode material would offer a green and economical option for fabricating high-performance microbial fuel cell-based devices towards various ends.

Impact of electrode micro- and nano-scale topography on the formation and performance of microbial electrodes

From a fundamental standpoint, microbial electrochemistry is unravelling a thrilling link between life and materials. Technically, it may be the source of a large number of new processes such as microbial fuel cells for powering remote sensors, autonomous sensors, microbial electrolysers and equipment for effluent treatment. Microbial electron transfers are also involved in many natural processes such as biocorrosion. In these contexts, a huge number of studies have dealt with the impact of electrode materials, coatings and surface functionalizations but very few have focused on the effect of the surface topography, although it has often been pointed out as a key parameter impacting the performance of electroactive biofilms. The first part of the review gives an overview of the influence of electrode topography on abiotic electrochemical reactions. The second part recalls some basics of the effect of surface topography on bacterial adhesion and biofilm formation, in a broad domain reaching beyond the context of electroactivity. On these well-established bases, the effect of surface topography is reviewed and analysed in the field of electroactive biofilms. General trends are extracted and fundamental questions are pointed out, which should be addressed to boost future research endeavours. The objective is to provide basic guidelines useful to the widest possible range of research communities so that they can exploit surface topography as a powerful lever to improve, or to mitigate in the case of biocorrosion for instance, the performance of electrode/biofilm interfaces.