Recent Developments in the Chemistry of Thiourea Oxides

A Titration Method for Standardization of Aqueous Sodium Chlorite Solutions Using Thiourea Dioxide

Accurate and cost-effective methods for the analysis of oxychlorine compounds in water are critical to modern chlorine-based water treatment. With alternatives to elemental chlorine and hypochlorite bleaches growing in popularity, simple quantification methods for the disinfectant chlorine dioxide (ClO2) in water, as well as chlorite (ClO2-) and chlorate (ClO3-), which are commonly used precursors in ClO2 generation, are required. However, currently, regulated standard methods require specialized equipment and do not effectively discriminate between molecular and ionic species. In this contribution, we present a simple titration-based method for chlorite determination in water using commercially available and easy-to-handle reagents. Specifically, chlorite is reduced with a slight excess of thioureadioxide (TUD). The remaining reductant is then back-titrated against a known amount of potassium permanganate, affording calculatable chlorite concentrations through measured consumption of a reductant and a clear visual endpoint upon accumulation of excess KMnO4. Straightforward methods for chlorite standardization with reasonable error and accuracy for field and/or lab application have the potential to greatly enhance quality assurance and therefore assist in resource deployment in water treatment.

One-step removal of hexavalent chromium in wide pH range using thiourea dioxide: the role of reactive species

One-step removal of hexavalent chromium in a wide pH range is of great significance. In this paper, a single thiourea dioxide (TD) and two-components thiourea dioxide/ethanolamine (MEA) were used as a green reducing agent for the efficient removal of Cr(vi), respectively. The reduction of Cr(vi) and the precipitation of Cr(iii) were carried out simultaneously under this reaction system. The experimental results proved that TD was activated by amine exchange reaction with MEA. In other words, MEA promoted the generation of an active isomeride of TD by changing the equilibrium position of the reversible reaction. After adding MEA, the removal rate of Cr(vi) and total Cr could reach industrial water discharge standards in a wide pH range of 8-12. The change of pH, reduction potential and the decomposition rate of TD were investigated in the reaction processes. Meanwhile, reductive and oxidative reactive species were produced simultaneously during this reaction process. Further, oxidative reactive species (O₂˙^- and ¹O₂) were beneficial for the decomplexation of Cr(iii) complexes and the formation of Cr(iii) precipitation. The experimental results also demonstrated that TD/MEA was effective in practical industrial wastewater. Hence this reaction system has a significant industrial application prospect.

Mechanochemistry Frees Thiourea Dioxide (TDO) from the 'Veils' of Solvent, Exposing All Its Reactivity

The synthesis of nitrogen-based heterocycles has always been considered essential in developing pharmaceuticals in medicine and agriculture. This explains why various synthetic approaches have been proposed in recent decades. However performing as methods, they often imply harsh conditions or the employment of toxic solvents and dangerous reagents. Mechanochemistry is undoubtedly one of the most promising technologies currently used for reducing any possible environmental impact, addressing the worldwide interest in counteracting environmental pollution. Following this line, we propose a new mechanochemical protocol for synthesizing various heterocyclic classes by exploiting thiourea dioxide (TDO)'s reducing proprieties and electrophilic nature. Simultaneously exploiting the low cost of a component of the textile industry such as TDO and all the advantages brought by a green technique such as mechanochemistry, we plot a route towards a more sustainable and eco-friendly methodology for preparing heterocyclic moieties.

Synthesis of Sterically Encumbered Thiourea S-Oxides through Direct Thiourea Oxidation

Thiourea S-oxides can be viewed as formal analogs of the currently unknown diamino-substituted Criegee intermediates (urea O-oxides). However, the preparation of such S-oxides is rather challenging, and the direct oxidation of thioureas typically only leads to formation of desulfurized products. Employing the accurate revDSD-PBEP86-D4 double hybrid density functional, it was found that the peracid mediated oxidation of thiourea S-oxides exhibits a lower reaction barrier than the oxidation of the corresponding thiourea itself in contrast to most other ordinary thioketones. The undesired overoxidation reactivity, which is associated with strong π-donation from the thiourea's nitrogen atoms, can be partially suppressed by introduction of bulky substituents and the utilization of protic solvents. In this regard, we managed to prepare two sterically encumbered thiourea S-oxides in isolated yields of 35-40 %. The S-oxides are stable in the solid state and in alcoholic solutions at room temperature for extended periods of time, but swiftly decompose in aprotic solvents by disproportionation. A dimesityl-substituted thiourea S-oxide complexed with residual mCBA could be characterized by means of X-ray crystallography, confirming the importance of hydrogen bonding in the stabilization of the amino-substituted C=S⁺ -O^- moiety.

Thiourea-functionalized graphene aerogel for the aqueous phase sensing of toxic Pb(II) metal ions and H2O2

A simpler approach of functionalization for the fabrication of thiourea-functionalized-Graphene Aerogel (t-GA) is described here. Graphene Aerogel (GA) was synthesized from bio-mass, which on a simpler oxidative treatment get converted to its water-soluble version due to the impregnation of several oxygenous functionalities like carboxylic, hydroxyl, etc. Further, these carboxylated groups have been functionalized with the molecules of thiourea using the long known dicyclohexylcarbodiimide (DCC) as a coupling agent. The as-synthesized t-GA shows bright yellow fluorescence with a quantum yield of ~3% and holds the high-aqueous solubility and photostability. The fluorescence property of t-GA has been used here for the specific and selective sensing of toxic lead (Pb(II)) metal ions from the used many other metal ions via the fluorescence quenching and showed a limit of detection ~7.3 nM. Further, the mechanism for selective sensing was studied in detail and found to be preferable via ligand to metal charge transfer quenching mechanism. The cyclic voltammetry studies supported the selective sensing of Pb(II). Moreover, t-GA has also been studied for the sensing of hydrogen peroxide and as a yellow fluorescent ink.

Lignin condensation inhibition and antioxidant activity improvement in a reductive ternary DES fractionation microenvironment by thiourea dioxide self-decomposition

Deep eutectic solvents (DESs) as promising green solvents can efficiently remove the lignin component in lignocellulosic biomass.

Investigation of the reactivity properties of a thiourea derivative with anticancer activity by DFT and MD simulations

Spectroscopic analysis of 1-(2-fluorophenyl)-3-[3-(trifluoromethyl)phenyl]thiourea (FPTT) is reported. Experimental and theoretical analyses of FPTT, with molecular dynamics (MD) simulations, are reported for finding different parameters like identification of suitable excipients, interactions with water, and sensitivity towards autoxidation. Molecular dynamics and docking show that FPTT can act as a potential inhibitor for new drug. Additionally, local reactivity, interactivity with water, and compatibility of FPTT molecule with frequently used excipients have been studied by combined application of density functional theory (DFT) and MD simulations. Analysis of local reactivity has been performed based on selected fundamental quantum-molecular descriptors, while interactivity with water was studied by calculations of radial distribution functions (RDFs). Compatibility with excipients has been assessed through calculations of solubility parameters, applying MD simulations. Graphical abstract Reactive sites identified.

Synthesis of pure and C/S/N co-doped Titania on Al mesh and their photocatalytic usage in Benzene degradation

Pure and co-doped Titania thin films were prepared on aluminum substrates through the sol-gel method. The co-doped sample showed higher photocatalytic activity on benzene degradation compared to pure TiO₂ under visible light illumination. XRD results showed the anatase phase for both TiO₂ and co-doped TiO₂ lattices with an average crystalline size of 12.9 and 10.4 nm, respectively. According to the UV-visible absorption spectra results, co-doped Titania showed higher visible light absorption compared to pure Titania. The synergistic effect of dopants caused a redshift to visible light absorption and also the lifetime of the photogenerated electron-hole were increased by induced electron levels in Titania lattice. The novelty of this study is the reactor's specific design. We employed Al mesh as thin film substrate for 3 main reasons, first, the large surface area of the Al mesh causes to increase specific surface area of the photocatalysts, also it is a formable substrate which can be engineered geometrically to decrease the shadow spots so the thin films will receive the highest light irradiation. Also, the Al mesh flexibility facilitates the procedure of reactor design to reach a minimum pressure drop of airflow while it is installed in the air conditioners or HVAC systems.

On the Kinetics and Mechanism of the Thiourea Dioxide-Periodate Autocatalysis-Driven Iodine-Clock Reaction

The thiourea dioxide-periodate reaction has been investigated under acidic conditions using phosphate buffer within the pH range of 1.1-2.0 at 1.0 M ionic strength adjusted by sodium perchlorate. Absorbance-time series are monitored as a function of time at 468 nm, the isosbestic point of the I₂-I₃^- system. The profile of these kinetic runs follows either sigmoidal-shaped or rise-and-fall traces depending on the initial concentration ratio of the reactants. The clock species iodine appears after a well-defined but reproducible time lag even in substrate excess, meaning that the system may be classified as an autocatalysis-driven clock reaction. It is also demonstrated that the age of the thiourea dioxide solution markedly shortens the Landolt time, suggesting that the original form of thiourea dioxide (TDO) rearranges into a more reactive form and reacts faster than the original one. The behavior found is consistent with that recently observed in other oxidation reactions of TDO. To characterize the system quantitatively, a 22-step kinetic model is constructed from adapting the kinetic model of the TDO-iodate reaction published recently by supplementing it with six different reactions of periodate. By the help of seven fitted rate coefficients a sound agreement between the measured and calculated absorbance-time traces is obtained.

Reactivity of Small Oxoacids of Sulfur

Oxidation of sulfide to sulfate is known to consist of several steps. Key intermediates in this process are the so-called small oxoacids of sulfur (SOS)—sulfenic HSOH (hydrogen thioperoxide, oxadisulfane, or sulfur hydride hydroxide) and sulfoxylic S(OH)₂ acids. Sulfur monoxide can be considered as a dehydrated form of sulfoxylic acid. Although all of these species play an important role in atmospheric chemistry and in organic synthesis, and are also invoked in biochemical processes, they are quite unstable compounds so much so that their physical and chemical properties are still subject to intense studies. It is well-established that sulfoxylic acid has very strong reducing properties, while sulfenic acid is capable of both oxidizing and reducing various substrates. Here, in this review, the mechanisms of sulfide oxidation as well as data on the structure and reactivity of small sulfur-containing oxoacids, sulfur monoxide, and its precursors are discussed.

Exact Concentration Dependence of the Landolt Time in the Thiourea Dioxide-Bromate Substrate-Depletive Clock Reaction

The thiourea dioxide (TDO)-bromate reaction has been reinvestigated spectrophotometrically under acidic conditions using phosphoric acid-dihydrogen-phosphate buffer within the pH range of 1.1-1.8 at 1.0 M ionic strength adjusted by sodium perchlorate and at 25 °C. The title system shows a remarkable resemblance to the classical Landolt reaction, namely, the clock species (bromine) may only appear after the substrate TDO is completely consumed. Thus, the title system can be classified as substrate-depletive clock reaction. Despite the well-known slow rearrangement characteristic of TDO in acidic solution, it is surprisingly found that the Landolt time of the title reaction does not depend at all on the age of TDO solution applied. It is, however, shown experimentally that the inverse of Landolt time linearly depends on the initial bromate concentration as well as on the square of the hydrogen ion concentration. In addition to this, it is also noticed that dihydrogen phosphate markedly affects the Landolt time as well, and this feature may easily be taken into consideration by the H₂PO₄^- dependence of the rate of bromate-bromide reaction quantitatively. Based on the experiments, a simple three-step kinetic model is proposed from which a complex formula is derived to indicate the exact concentration dependence of the Landolt time.

Thiourea Dioxide As a Green and Affordable Reducing Agent for the ARGET ATRP of Acrylates, Methacrylates, Styrene, Acrylonitrile, and Vinyl Chloride

Thiourea dioxide, a green and inexpensive compound used at industrial scale, was employed as reducing agent for the controlled polymerization of a wide range of monomer families, namely, acrylates (methyl acrylate, 2-hydroxyethyl acrylate, butyl acrylate, methacrylates (2-(dimethylamino)ethyl methacrylate, 2-aminoethyl methacrylate hydrochloride, and methyl methacrylate), styrene, acrylonitrile, and vinyl chloride (nonactivated monomer) by ATRP. Mechanistic studies confirmed that the polymerizations are ruled by the activators regenerated by electron transfer (ARGET) mechanism. It is worth noting that vinyl chloride has never been polymerized by ARGET ATRP. The system proved to be very versatile and robust, working in organic solvents, organic/water mixtures, and aqueous medium at near room temperature with low metal catalyst concentration. Chain extension experiments confirmed the high chain-end functionality of the polymers, allowing the preparation of several well-defined block copolymers.

Autocatalysis-Driven Clock Reaction III: Clarifying the Kinetics and Mechanism of the Thiourea Dioxide-Iodate Reaction in an Acidic Medium

The thiourea dioxide-iodate reaction has been reinvestigated spectrophotometrically under acidic conditions using phosphoric acid-dihydrogen phosphate buffer within the pH range of 1.1-1.8 at 1.0 M ionic strength adjusted by sodium perchlorate and at 25 °C. The system was found to exhibit clock behavior, having a well-defined and reproducible time lag called Landolt time, though elementary iodine may even be detected in substrate excess; hence, under these conditions, the reaction can be classified as an autocatalysis-driven clock reaction. It is clearly demonstrated that the previously proposed kinetic model suffers from serious drawbacks from both theoretical and experimental points of view. The reaction may be characterized by either sigmoidal-shaped or rise-and-fall kinetic traces, depending on the initial concentration ratio of the reactants. Iodide significantly accelerates the appearance of the clock species iodine acting therefore as an autocatalyst. The age of stock TDO solution also has a great, so far completely overlooked impact on the Landolt time. On the basis of evaluating simultaneously the kinetic curves, a 16 step kinetic model including 5 well-known rapidly established equilibria is proposed with 7 fitted rate coefficients in which the rate coefficients of both forms of TDO were determined.

Real-Time in Vivo Detection of H2O2 Using Hyperpolarized 13C-Thiourea

Reactive oxygen species (ROS) are essential cellular metabolites widely implicated in many diseases including cancer, inflammation, and cardiovascular and neurodegenerative disorders. Yet, ROS signaling remains poorly understood, and their measurements are a challenge due to high reactivity and instability. Here, we report the development of ¹³C-thiourea as a probe to detect and measure H₂O₂ dynamics with high sensitivity and spatiotemporal resolution using hyperpolarized ¹³C magnetic resonance spectroscopic imaging. In particular, we show ¹³C-thiourea to be highly polarizable and to possess a long spin-lattice relaxation time (T₁), which enables real-time monitoring of ROS-mediated transformation. We also demonstrate that ¹³C-thiourea reacts readily with H₂O₂ to give chemically distinguishable products in vitro and validate their detection in vivo in a mouse liver. This study suggests that ¹³C-thiourea is a promising agent for noninvasive detection of H₂O₂ in vivo. More broadly, our findings outline a viable clinical application for H₂O₂ detection in patients with a range of diseases.

Kinetics and Mechanism of the Oxidation of Thiourea Dioxide by Iodine in a Slightly Acidic Medium

The thiourea dioxide (TDO)-iodine reaction was investigated spectrophotometrically monitoring the consumption of total amount of iodine at 468 nm, at T = 25.0 ± 0.1 °C, and at 0.5 M ionic strength in buffered slightly acidic medium. The nitrogen- and carbon-containing products were found to be ammonium ion and dissolved carbon dioxide, respectively, while from sulfur part sulfate ion was exclusively detected, when fresh TDO solution was used. The stoichiometry of the reaction was established as 2I₂ + TDO + 4H₂O → SO₄^2- + 2NH₄⁺ + 4I^- + CO₂ + 4H⁺ indicating a strict 2:1 stoichiometric ratio. However, using aged TDO solution this stoichiometric ratio is shifted to lower values suggesting the formation of elementary sulfur augmented by the 2TDO + I₂ + 4H₂O → S + SO₄^2- + 4NH₄⁺ + 2I^- + 2CO₂ hypothetical limiting stoichiometry. We also confirmed experimentally that in aqueous solution TDO slowly rearranges into an unindentified species. This species then produces elementary sulfur at a later stage of the aging process via subsequent reactions accounting for a loss of reducing power. The direct reaction between TDO and iodine was found to be relatively rapid and completed within seconds in absence of initially added iodide ion. Formation of the latter ion, however, strongly inhibits the oxidation process; hence, the system is autoinhibitory with respect to iodide ion. Furthermore, increase of pH markedly accelerates the reaction as well. These observations suggest that a short-lived steady-state intermediate (iodinated TDO) is produced in a rapid pre-equilibrium, where iodide and hydrogen ions are also involved. A nine-step kinetic model, to be able to describe the most important characteristics of the experimental curves with four fitted parameters, is proposed and discussed.

Thiourea dioxide as a unique eco-friendly coreactant for luminol chemiluminescence in the sensitive detection of luminol, thiourea dioxide and cobalt ions

Thiourea dioxide, a unique reductant that can generate oxygen upon decomposition, has been investigated as an efficient, cost-effective, and stable coreactant.