Adsorptive removal of heavy metals from aqueous solutions: Progress of adsorbents development and their effectiveness

Increased levels of heavy metals (HMs) in aquatic environments poses serious health and ecological concerns. Hence, several approaches have been proposed to eliminate/reduce the levels of HMs before the discharge/reuse of HMs-contaminated waters. Adsorption is one of the most attractive processes for water decontamination; however, the efficiency of this process greatly depends on the choice of adsorbent. Therefore, the key aim of this article is to review the progress in the development and application of different classes of conventional and emerging adsorbents for the abatement of HMs from contaminated waters. Adsorbents that are based on activated carbon, natural materials, microbial, clay minerals, layered double hydroxides (LDHs), nano-zerovalent iron (nZVI), graphene, carbon nanotubes (CNTs), metal organic frameworks (MOFs), and zeolitic imidazolate frameworks (ZIFs) are critically reviewed, with more emphasis on the last four adsorbents and their nanocomposites since they have the potential to significantly boost the HMs removal efficiency from contaminated waters. Furthermore, the optimal process conditions to achieve efficient performance are discussed. Additionally, adsorption isotherm, kinetics, thermodynamics, mechanisms, and effects of varying adsorption process parameters have been introduced. Moreover, heavy metal removal driven by other processes such as oxidation, reduction, and precipitation that might concurrently occur in parallel with adsorption have been reviewed. The application of adsorption for the treatment of real wastewater has been also reviewed. Finally, challenges, limitations and potential areas for improvements in the adsorptive removal of HMs from contaminated waters are identified and discussed. Thus, this article serves as a comprehensive reference for the recent developments in the field of adsorptive removal of heavy metals from wastewater. The proposed future research work at the end of this review could help in addressing some of the key limitations facing this technology, and create a platform for boosting the efficiency of the adsorptive removal of heavy metals.

Thermodynamics, kinetics and isothermal studies of tartrazine adsorption onto microcline/MWCNTs nanocomposite and the regeneration potentials

The quest for a cheap, effective, and eco-friendly wastewater treatment technique that is free of secondary toxic byproducts, calls for the fabrication of a nature-friendly adsorbent with a robust capacity to decontaminate polluted water sources and be recycled. To this end, we report the fabrication of novel nanocomposite (KMCM) from microcline (KMC) and multiwall carbon nanotubes (MWCNTs). The adsorbents (KMC and KMCM) were characterized using XRD, BET, SEM, TGA and FTIR. The novel and low-cost nano sorbent were designed for the elimination of tartrazine (Tatz) from wastewater. The adsorption of Tatz onto KMC and KMCM was influenced by adsorbent dose, initial Tatz concentration, contact time and solution pH. Experimental data acquired from the equilibrium studies were well addressed by the Langmuir isotherm model. The maximum uptake capacity of 37.96 mg g^-1 and 67.17 mg g^-1 were estimated for KMC and KMCM. The kinetics for the adsorption of Tatz onto KMC and KMCM was best expressed by pseudo-second-order and Elovich models. The thermodynamic parameters revealed that the uptake of Tatz onto KMC and KMCM was an endothermic (ΔH: KMC = 35.0 kJ mol^-1 and KMCM = 42.91 kJ mol^-1), entropy-driven (ΔS: KMC = 177.6 J K^-1 mol^-1 and KMCM = 214.2 J K^-1 mol^-1) and spontaneous process. Meanwhile, KMCM demonstrated good reusability potential and superior adsorption efficiency when compared to other adsorbents.

A Thorough Examination of the Solution Conditions and the Use of Carbon Nanoparticles Made from Commercial Mesquite Charcoal as a Successful Sorbent for Water Remediation

Water pollution has invaded seas, rivers, and tap water worldwide. This work employed commercial Mesquite charcoal as a low-cost precursor for fabricating Mesquite carbon nanoparticles (MUCNPs) using a ball-milling process. The scanning electron energy-dispersive microscopy results for MUCNPs revealed a particle size range of 52.4-75.0 nm. The particles were composed mainly of carbon with trace amounts of aluminum, potassium, calcium, titanium, and zinc. The X-ray diffraction peaks at 26.76 and 43.28 2θ° ascribed to the (002) and (100) planes indicated a crystalized graphite phase. Furthermore, the lack of FT-IR vibrations above 3000 cm^-1 showed that the MUCNPs were not functionalized. The MUCNPs' pore diameter, volume, and surface area were 114.5 Ǻ, 0.363 cm³ g^-1, and 113.45 m² g^-1. The batch technique was utilized to investigate MUCNPs' effectiveness in removing chlorohexidine gluconate (CHDNG) from water, which took 90 min to achieve equilibrium and had an adsorption capacity of 65.8 mg g^-1. The adsorption of CHDNG followed pseudo-second-order kinetics, with the rate-limiting step being diffusion in the liquid film. The Langmuir isotherm dominated the CHDNG adsorption on the MUCNPs with a correlation coefficient of 0.99. The thermodynamic studies revealed that CHDNG adsorption onto the MUCNPs was exothermic and favorable, and its spontaneity increased inversely with CHDNG concentration. The ball-milling-made MUCNPs demonstrated consistent efficiency through regeneration-reuse cycles.

Sweep-Out of Tigecycline, Chlortetracycline, Oxytetracycline, and Doxycycline from Water by Carbon Nanoparticles Derived from Tissue Waste

Pharmaceutical pollution has pervaded many water resources all over the globe. The propagation of this health threat drew the researchers' concern in seeking an efficient solution. This study introduced toilet paper waste as a precursor for carbon nanoparticles (CRNPs). The TEM results showed a particle size range of 30.2 nm to 48.1 nm, the BET surface area was 283 m² g^-1, and the XRD pattern indicated cubical-graphite crystals. The synthesized CRNPs were tested for removing tigecycline (TGCN), chlortetracycline (CTCN), oxytetracycline (OTCN), and doxycycline (DXCN) via the batch process. The adsorption equilibrium time for TGCN, DXCN, CTCN, and OTCN was 60 min, and the concentration influence revealed an adsorption capacity of 172.5, 200.1, 202.4, and 200.0 mg g^-1, respectively. The sorption of the four drugs followed the PSFO, and the LFDM models indicated their high sorption affinity to the CRNPs. The adsorption of the four drugs fitted the multilayer FIM that supported the high-affinity claim. The removals of the four drugs were exothermic and spontaneous physisorption. The fabricated CRNPs possessed an excellent remediation efficiency for contaminated SW and GW; therefore, CRNPs are suggested for water remediation as low-cost sorbent.

Low-Cost Carbon Nanoparticles for Removing Hazardous Organic Pollutants from Water: Complete Remediation Study and Multi-Use Investigation

Continuous waste discharge into natural water resources in many countries is a severe global issue, and seeking an effective solution is a researcher’s concern. Herein, toilet paper waste was a low-cost precursor for preparing carbon nanoparticles (TPCNPs). The characterization of TPCNPs revealed a 30 nm to 50 nm particle size, a 264 m2 g−1 surface area, and a cubical graphite lattice XRD pattern. The TPCNPs were tested for removing malachite green (MG), indigo carmine (IC), rhodamine B (RB), and methylene blue (MB) dyes from water. The solution parameters were examined for the sorption process, and a pH of 5.0 suited the MB removal, while a pH of 6.0 was suitable for MG, IC, and RB. The effect of concentration investigation showed an adsorption capacity of 110.9, 64.8, 73.5, and 98 mg g−1 for MG, IC, RB, and MB, respectively. The sorption of the four dyes fitted the Langmuir isotherm model; it was exothermic and spontaneous. The water remediation was tested using groundwater and seawater samples (GW and SW) spiked with pollutants. It is worth mentioning that one treatment sufficed for the remediation of GW and SW contaminated by 5 mg L−1 concentration, while a double treatment was required for 10 mg L−1 pollution in both samples.

The Use of Diatomite as a Catalyst Carrier for the Synthesis of Carbon Nanotubes

In this article, multiwalled carbon nanotubes (MWCNTs) have been synthesized on the surface of a diatomite mineral impregnated with transition metal salts using a propane-butane mixture in a chemical vapor deposition reactor at atmospheric pressure. The catalyst concentration and synthesis temperature have been varied in order to understand their effects on the formation of MWCNTs and their morphology. Diatomite was chosen as a catalyst carrier due to its elemental composition. It is mainly composed of amorphous silica, quartz and also contains such metals as Fe, K, Ca, Mn, Cr, Ti, and Zn, which makes it a promising material for use as a catalyst carrier when synthesizing carbon nanotubes (CNTs) by catalytic chemical vapor deposition (C-CVD). For the synthesis of carbon nanotubes by C-CVD on the surface of the diatomite, the following salts were used as a catalyst: CoCl₂·6H₂O; Ni(NO₃)₂·6H₂O, and the concentrations of the solutions were 0.5; 1.0 and 1.5 M. Natural diatomite was characterized by X-ray diffraction analysis (XRD) and Scanning Electron Microscopy (SEM) analysis.