Synthesis Optimization, Shaping, and Heat Reallocation Evaluation of the Hydrophilic Metal-Organic Framework MIL-160(Al)

A Scalable Robust Microporous Al-MOF for Post-Combustion Carbon Capture

Herein, a robust microporous aluminum tetracarboxylate framework, MIL-120(Al)-AP, (MIL, AP: Institute Lavoisier and Ambient Pressure synthesis, respectively) is reported, which exhibits high CO2 uptake (1.9 mmol g-1 at 0.1 bar, 298 K). In situ Synchrotron X-ray diffraction measurements together with Monte Carlo simulations reveal that this structure offers a favorable CO2 capture configuration with the pores being decorated with a high density of µ2-OH groups and accessible aromatic rings. Meanwhile, based on calculations and experimental evidence, moderate host-guest interactions Qst (CO2) value of MIL-120(Al)-AP (-40 kJ mol-1) is deduced, suggesting a relatively low energy penalty for full regeneration. Moreover, an environmentally friendly ambient pressure green route, relying on inexpensive raw materials, is developed to prepare MIL-120(Al)-AP at the kilogram scale with a high yield while the Metal- Organic Framework (MOF) is further shaped with inorganic binders as millimeter-sized mechanically stable beads. First evidences of its efficient CO2/N2 separation ability are validated by breakthrough experiments while operando IR experiments indicate a kinetically favorable CO2 adsorption over water. Finally, a techno-economic analysis gives an estimated production cost of ≈ 13 $ kg-1, significantly lower than for other benchmark MOFs. These advancements make MIL-120(Al)-AP an excellent candidate as an adsorbent for industrial-scale CO2 capture processes.

When Polymorphism in Metal-Organic Frameworks Enables Water Sorption Profile Tunability for Enhancing Heat Allocation and Water Harvesting Performance

The development of thermally driven water-sorption-based technologies relies on high-performing water vapor adsorbents. Here, polymorphism in Al-metal-organic frameworks is disclosed as a new strategy to tune the hydrophilicity of MOFs. This involves the formation of MOFs built from chains of either trans- or cis- µ-OH-connected corner-sharing AlO4(OH)2 octahedra. Specifically, [Al(OH)(muc)] or MIP-211, is made of trans, trans-muconate linkers, and cis-µ-OH-connected corner-sharing AlO4(OH)2 octahedra giving a 3D network with sinusoidal channels. The polymorph MIL-53-muc has a tiny change in the chain structure that results in a shift of the step position of the water isotherm from P/P0 ≈ 0.5 in MIL-53-muc, to P/P0 ≈ 0.3 in MIP-211. Solid-state NMR and Grand Canonical Monte Carlo reveal that the adsorption occurs initially between two hydroxyl groups of the chains, favored by the cis-positioning in MIP-211, resulting in a more hydrophilic behavior. Finally, theoretical evaluations show that MIP-211 would allow achieving a coefficient of performance for cooling (COPc) of 0.63 with an ultralow driving temperature of 60 °C, outperforming benchmark sorbents for small temperature lifts. Combined with its high stability, easy regeneration, huge water uptake capacity, green synthesis, MIP-211 is among the best adsorbents for adsorption-driven air conditioning and water harvesting from the air.

A Versatile Shaping Method of Very-High Loading Porous Solids Paper Adsorbent Composites

Owing to their high porosity and tunability, porous solids such as metal-organic frameworks (MOFs), zeolites, or activated carbons (ACs) are of great interest in the fields of air purification, gas separation, and catalysis, among others. Nonetheless, these materials are usually synthetized as powders and need to be shaped in a more practical way that does not modify their intrinsic property (i.e., porosity). Elaborating porous, freestanding and flexible sheets is a relevant shaping strategy. However, when high loadings (>70 wt.%) are achieved the mechanical properties are challenged. A new straightforward and green method involving the combination softwood bleached kraft pulp fibers (S) and nano-fibrillated cellulose (NFC) is reported, where S provides flexibility while NFC acts as a micro-structuring and mechanical reinforcement agent to form high loadings porous solids paper sheets (>70 wt.%). The composite has unobstructed porosity and good mechanical strength. The sheets prepared with various fillers (MOFs, ACs, and zeolites) can be rolled, handled, and adapted to different uses, such as air purification. As an example of potential application, a MOF paper composite has been considered for the capture of polar volatile organic compounds exhibiting better performance than beads and granules.

Confined Water Cluster Formation in Water Harvesting by Metal-Organic Frameworks: CAU-10-H versus CAU-10-CH3

Several metal-organic frameworks (MOFs) excel in harvesting water from the air or as heat pumps as they show a steep increase in water uptake at 10-30 % relative humidity (RH%). A precise understanding of which structural characteristics govern such behavior is lacking. Herein, CAU-10-H and CAU-10-CH3 are studied with H, CH3 corresponding to the functions grafted to the organic linker. CAU-10-H shows a steep water uptake ≈18 RH% of interest for water harvesting, yet the subtle replacement of H by CH3 in the organic linker drastically changes the water adsorption behavior to less steep water uptake at much higher humidity values. The materials' structural deformation and water ordering during adsorption with in situ sum-frequency generation, in situ X-ray diffraction, and molecular simulations are unraveled. In CAU-10-H, an energetically favorable water cluster is formed in the hydrophobic pore, tethered via H-bonds to the framework μOH groups, while for CAU-10-CH3, such a favorable cluster cannot form. By relating the findings to the features of water adsorption isotherms of a series of MOFs, it is concluded that favorable water adsorption occurs when sites of intermediate hydrophilicity are present in a hydrophobic structure, and the formation of energetically favorable water clusters is possible.

Greatly Intensified Guest Exchange Strategy for Highly-Efficient Activation of Metal-Organic Frameworks

The preservation and accessibility of pores are prerequisites to the application of metal-organic frameworks (MOFs). Activation is a key step to eliciting rich features of pores, but it needs a repeated solvent-exchange process which is tedious and time/cost-consuming. Herein, a facile strategy for highly-efficient activation of MOFs utilizing rotating packed bed is proposed. With the tremendous enhancement of molecular mixing and mass transfer in high-gravity and strong-shearing surrounding, nine representative MOFs are completely activated within 2 h without structural change. Compared with conventional process, this activation displays surprising efficiency by accelerating the diffusion of solvents and redissolution of residual reactants in the pores. The complete activation time can be significantly shortened by over 90%. As a proof-of-concept, the methane storage of as-activated UiO-66 is five times that of as-synthesized UiO-66. This strategy provides a potential platform with industrial worth for the activation of MOF materials with ultra-high efficiency and versatility.

Microscopic insight into the shaping of MOFs and its impact on CO2 capture performance

The traditional synthesis method produces microcrystalline powdered MOFs, which prevents direct implementation in real-world applications which demand strict control of shape, morphology and physical properties. Therefore, shaping of MOFs via the use of binders is of paramount interest for their practical use in gas adsorption/separation, catalysis, sensors, etc. However, so far, the binders have been mostly selected by trial-and-error without anticipating the adhesion between the MOF and binder components to ensure the processability of homogeneous and mechanically stable shaped MOFs and the impact of the shaping on the intrinsic properties of the MOFs has been overlooked. Herein, we deliver a first systematic multiscale computational exploration of MOF/binder composites by selecting CALF-20, a prototypical MOF for real application in the field of CO2 capture, and a series of binders that cover a rather broad spectrum of properties in terms of rigidity/flexibility, porosity, and chemical functionality. The adhesion between the two components and hence the effectiveness of the shaping as well as the impact of the overall porosity of the CALF-20/binder on the CO2/N2 selectivity, CO2 sorption capacity and kinetics was analyzed. Shaping of CALF-20 by carboxymethyl cellulose was predicted to enable a fair compromise between excellent adhesion between the two components, whilst maintaining high CO2/N2 selectivity, large CO2 uptake and CO2 transport as fast as in the CALF-20. This multiscale computational tool paves the way towards the selection of an appropriate binder to achieve an optimum shaping of a given MOF in terms of processability whilst maintaining its high level of performance.

Methyl-Functionalized Al-Based MOF ZJU-620(Al): A Potential Physisorbent for Carbon Dioxide Capture

Developing Al-based metal-organic frameworks (MOFs) with moisture-resistance ability is a challenge for carbon dioxide (CO2) capture. Methyl-functionalized Al-based MOF ZJU-620(Al), with excellent chemical-thermal stability and specific surface area of 1347 m2/g, observed here, is a potential adsorbent for CO2 capture with good recyclability and large capacity up to 4.25 mmol/g at 298 K and 1 atm. CO2 molecules are largely trapped on two types of sites. One (site I) is near the AlO6 clusters, and another (site II) is between two parallel benzene rings with a distance of 6.64 Å. ZJU-620(Al) can be used for CO2/N2 (15/85) separation with the excellent selectivity up to 107.20 at 273 K and 31.93 at 298 K, and the separation factor of 13.68. It is also with excellent moisture-resistance ability due to 5% breakthrough time (outlet concentration reached the 5% of inlet concentration) without reduction at 80% relative humidity than under dry conditions. Water molecules occupy a small amount of CO2 adsorption site I, but they almost do not occupy the CO2 adsorption site II due to hydrophobic methyl-functional ligands. Moreover, CO2 can be adsorbed on the ZJU-620(Al) surface through C═O···H binding of water molecules with high affinity. Thus, ZJU-620(Al) is a candidate adsorbent for CO2 capture and separation especially under humidity conditions.

Recent progress in high-performance environmental impacts of the removal of radionuclides from wastewater based on metal-organic frameworks: a review

The nuclear industry is rapidly developing and the effective management of nuclear waste and monitoring the nuclear fuel cycle are crucial. The presence of various radionuclides such as uranium (U), europium (Eu), technetium (Tc), iodine (I), thorium (Th), cesium (Cs), and strontium (Sr) in the environment is a major concern, and the development of materials with high adsorption capacity and selectivity is essential for their effective removal. Metal-organic frameworks (MOFs) have recently emerged as promising materials for removing radioactive elements from water resources due to their unique properties such as tunable pore size, high surface area, and chemical structure. This review provides an extensive analysis of the potential of MOFs as adsorbents for purifying various radionuclides rather than using different techniques such as precipitation, filtration, ion exchange, electrolysis, solvent extraction, and flotation. This review discusses various MOF fabrication methods, focusing on minimizing environmental impacts when using organic solvents and solvent-free methods, and covers the mechanism of MOF adsorption towards radionuclides, including macroscopic and microscopic views. It also examines the effectiveness of MOFs in removing radionuclides from wastewater, their behavior on exposure to high radiation, and their renewability and reusability. We conclude by emphasizing the need for further research to optimize the performance of MOFs and expand their use in real-world applications. Overall, this review provides valuable insights into the potential of MOFs as efficient and durable materials for removing radioactive elements from water resources, addressing a critical issue in the nuclear industry.

A facile spray-pressing synthesis approach for reusable photothermal masks

Certain types of face masks are highly efficient in protecting humans from bacterial and viral pathogens, and growing concerns with high safety, low cost, and wide market suitability have accelerated the replacement of reusable face masks with disposable ones during the last decades. However, wearing these masks creates countless problems associated with personnel comfort as well as more significant issues related to the cost of fabrication, the generation of medical waste, and environmental contaminants. In this work, we present a facile spray-pressing technique for the production of P-masks with a potential scale-up prospect by adding a graphene layer on one side of meltblown fabric and a functional layer on the other side. In principle, this technique could be easily integrated into the present automatic mask production process and the masks have self-cleaning and/or self-sterilizing properties when it is exposed to solar or simulated solar irradiation.

Tuning Hydrophilicity of Aluminum MOFs by a Mixed-Linker Strategy for Enhanced Performance in Water Adsorption-Driven Heat Allocation Application

Water adsorption-driven heat transfer (AHT) technology has emerged as a promising solution to address crisis of the global energy consumption and environmental pollution of current heating and cooling processes. Hydrophilicity of water adsorbents plays a decisive role in these applications. This work reports an easy, green, and inexpensive approach to tuning the hydrophilicity of metal-organic frameworks (MOFs) by incorporating mixed linkers, isophthalic acid (IPA), and 3,5-pyridinedicarboxylic acid (PYDC), with various ratios in a series of Al-xIPA-(100-x)PYDC (x: feeding ratio of IPA) MOFs. The designed mixed-linkers MOFs show a variation of hydrophilicity along the fraction of the linkers. Representative compounds with a proportional mixed linker ratio denoted as KMF-2, exhibit an S-shaped isotherm, an excellent coefficient of performance of 0.75 (cooling) and 1.66 (heating) achieved with low driving temperature below 70 °C which offers capability to employ solar or industrial waste heat, remarkable volumetric specific energy capacity (235 kWh m^-3 ) and heat-storage capacity (330 kWh m^-3 ). The superiority of KMF-2 to IPA or PYDC-containing single-linker MOFs (CAU-10-H and CAU-10pydc, respectively) and most of benchmark adsorbents illustrate the effectiveness of the mixed-linker strategy to design AHT adsorbents with promising performance.

Carbon dioxide separation and capture by adsorption: a review

Rising adverse impact of climate change caused by anthropogenic activities is calling for advanced methods to reduce carbon dioxide emissions. Here, we review adsorption technologies for carbon dioxide capture with focus on materials, techniques, and processes, additive manufacturing, direct air capture, machine learning, life cycle assessment, commercialization and scale-up.

Novel strategies for the formulation and processing of aluminum metal-organic framework-based sensing systems toward environmental monitoring of metal ions

Aluminum is a relatively inexpensive and abundant metal for the mass production of metal-organic frameworks (MOFs). Aluminum-based MOFs (Al-MOFs) have drawn a good deal of research interest due to their unique properties for diverse applications (e.g., excellent chemical and structural stability). This review has been organized to highlight the current progress achieved in the synthesis/functionalization of Al-MOF materials with the special emphasis on their sensing application, especially toward metal ion pollutants in the liquid phase. To learn more about the utility of Al-MOF-based sensing systems, their performances have been evaluated for diverse metallic components in reference to many other types of sensing systems (in terms of the key quality assurance (QA) criteria such as limit of detection (LOD)). Finally, the challenges and outlook for Al-MOF-based sensing systems are discussed to help expand their real-world applications.

Assessment of Enzyme Functionality at Metal-Organic Framework Interfaces Developed through Molecular Simulations

The catalytic efficiency and unrivaled selectivity with which enzymes convert substrates to products have been tapped for widespread chemical transformations within biomedical technology, biofuel production, gas sensing, and the upgrading of commodity chemicals, just to name a few. However, the feasibility of enzymes implementation is challenged by the lack of reusability and loss of native catalytic activity due to the irreversible biocatalyst denaturation at high temperatures and in the presence of industrial solvents. Enzyme immobilization, a prerequisite for enzyme reusability, offers controllable strategies for increased functional viability of the biocatalyst in a synthetic environment. Herein we used molecular dynamics (MD) simulations and probed the noncovalent interactions between model enzymes of technological interest, i.e., carbonic anhydrase (CA) and myeloperoxidase (MPO), with selected metal-organic frameworks (MOFs; MIL-160 and ZIF-8) of proven industrial implementation. We found that the CA and MPO can bind to MIL-160 at optimal binding energies of 201 and 501 kJ mol^-1, respectively, that are strongly influenced by the increased incidence of hydrogen bonding between enzymes and the frameworks. The free energy of binding of enzymes to ZIF-8, on the other hand, was found to be less strongly influenced by hydrogen bonding networks relative to the occurrence of hydrophobic-hydrophobic interactions that yielded 106 kJ mol^-1 for CA and 201 kJ mol^-1 for MPO.

High-yield, green and scalable methods for producing MOF-303 for water harvesting from desert air

Metal-organic frameworks (MOFs) are excellent candidates for water harvesting from desert air. MOF-303 (Al(OH)(PZDC), where PZDC is 1-H-pyrazole-3,5-dicarboxylate), a robust and water-stable MOF, is a particularly promising water-harvesting sorbent that can take up water at low relative humidity and release it under mild heating. Accordingly, development of a facile, high-yield synthesis method for its production at scale is highly desirable. Here we report detailed protocols for the green, water-based preparation of MOF-303 on both gram and kilogram scales. Specifically, four synthetic methods (solvothermal, reflux, vessel and microwave), involving different equipment requirements, are presented to guarantee general accessibility. Typically, the solvothermal method takes ~24 h to synthesize MOF-303, while the reflux and vessel methods can reduce the time to 4-8 h. With the microwave-assisted method, the reaction time can be further reduced to just 5 min. In addition, we provide guidance on the characterization of MOF-303, as well as water-harvesting MOFs in general, to ensure high quality of the product in terms of its purity, crystallinity, porosity and water uptake. Furthermore, to address the need for future commercialization of this material, we demonstrate that our protocol can be employed to produce 3.5 kg per batch with a yield of 91%. MOF-303 synthesized at this large scale shows similar crystallinity and water uptake capacity compared to the respective material produced at a small scale. Our synthetic procedure is green and water-based, and can produce the MOF within hours.

Synthesis and shaping of metal-organic frameworks: a review

Metal-organic frameworks (MOFs) possess excellent advantages, such as high porosity, large specific surface area, and an adjustable structure, showing good potential for applications in gas adsorption and separation, catalysis, conductivity, sensing, magnetism, etc. However, they still suffer from significant limitations in terms of the scale-up synthesis and shaping, hindering the realization of large-scale commercial applications. Despite some attempts having been devoted to addressing this, challenges remain. In this paper, we outline the advantages and drawbacks of existing synthetic routes such as electrochemistry, microwave, ultrasonic radiation, green solvent reflux, room temperature stirring, steam-assisted transformation, mechanochemistry, and fluid chemistry in terms of scale-up production. Then, the shaping methods of MOFs such as extrusion, mechanical compaction, rolling granulation, spray drying, gel technology, embedded granulation, phase inversion, 3D printing and other shaping methods for the preparation of membranes, coatings and nanoparticles are discussed. Finally, perspectives on the large-scale synthesis and shaping of MOFs are also proposed. This work helps provide in-depth insight into the scale-up production and shaping process of MOFs and boost commercial applications of MOFs.

Separation of Branched Alkanes Feeds by a Synergistic Action of Zeolite and Metal-Organic Framework

Zeolites and metal-organic frameworks (MOFs) are considered as "competitors" for new separation processes. The production of high-quality gasoline is currently achieved through the total isomerization process that separates pentane and hexane isomers while not reaching the ultimate goal of a research octane number (RON) higher than 92. This work demonstrates how a synergistic action of the zeolite 5A and the MIL-160(Al) MOF leads to a novel adsorptive process for octane upgrading of gasoline through an efficient separation of isomers. This innovative mixed-bed adsorbent strategy encompasses a thermodynamically driven separation of hexane isomers according to the degree of branching by MIL-160(Al) coupled to a steric rejection of linear isomers by the molecular sieve zeolite 5A. Their adsorptive separation ability is further evaluated under real conditions by sorption breakthrough and continuous cyclic experiments with a mixed bed of shaped adsorbents. Remarkably, at the industrially relevant temperature of 423 K, an ideal sorption hierarchy of low RON over high RON alkanes is achieved, i.e., n-hexane ≫ n-pentane ≫ 2-methylpentane > 3-methylpentane ⋙ 2,3-dimethylbutane > isopentane ≈ 2,2-dimethylbutane, together with a productivity of 1.14 mol dm^-3 and a high RON of 92, which is a leap-forward compared with existing processes.

Diverse Applications of Biomass-Derived 5-Hydroxymethylfurfural and Derivatives as Renewable Starting Materials

This Review summarizes recent efforts to capitalize on 5-hydroxymethylfurfural (HMF) and related furans as emerging building blocks for the synthesis of fine chemicals and materials, with a focus on advanced applications within medicinal and polymer chemistry, as well as nanomaterials. As with all chemical industries, these fields have historically relied heavily on petroleum-derived starting materials, an unsustainable and polluting feedstock. Encouragingly, the emergent chemical versatility of biomass-derived furans has been shown to facilitate derivatization towards valuable targets. Continued work on the synthetic manipulation of HMF, and related derivatives, for access to a wide range of target compounds and materials is crucial for further development. Increasingly, biomass-derived furans are being utilized for a wide range of chemical applications, the continuation of which is paramount to accelerate the paradigm shift towards a sustainable chemical industry.

Evaluation of Iron-Based Metal-Organic Framework Activation Temperatures in Acetylene Adsorption

One of the major issues regarding long-term human space exploration is the need for a breathable atmosphere. A major component toward achieving this goal is both the removal of exhaled carbon dioxide (CO₂) and the generation or recovery of oxygen (O₂). NASA's current technology only operates at about 50% efficiency due to the need to vent the methane that is produced during the CO₂ reduction process. One method of improving the efficiency of this process is through plasma pyrolysis, wherein the methane is pyrolyzed to produce hydrogen and various dehydrogenated carbon byproducts. In this process, acetylene is one of the main components of this byproduct stream. Unfortunately, while the concentration of this effluent is generally high in hydrogen (>90% typically), the presence of the acetylene waste product can act as a poison for the ruthenium-alumina catalyst used in the CO₂-reducing Sabatier process, requiring a removal step. Metal-organic frameworks (MOFs) represent a valuable method for removing these unsaturated hydrocarbons due to their high tunability, particularly through the incorporation of open metal sites. In this study, two common iron-based MOFs, MIL-100 and PCN-250, were studied for their ability to adsorb acetylene. A combination of gas adsorption analysis and density functional theory calculation results shows the ability of these materials to undergo a thermal-induced reduction event, which results in an improvement in gas adsorption performance. This improvement in gas performance appears to be at least partially due to the increased presence of π-backbonding toward the acetylene molecules.

Tailoring Multiple Sites of Metal-Organic Frameworks for Highly Efficient and Reversible Ammonia Adsorption

The structural diversity and designability of metal-organic frameworks (MOFs) make these porous materials a strong candidate for NH₃ uptake. However, to achieve a high NH₃ capture capacity and good recyclability of MOFs at the same time remains a great challenge. Here, a multiple-site ligand screening strategy of MOFs is proposed for highly efficient and reversible NH₃ uptake for the first time. Based on the optimized DFT results for various possible ligands, pyrazole-3,5-dicarboxylate with multiple sites was screened as the best ligand to construct robust MOF-303(Al) with Al³⁺. It is experimentally found that the NH₃ adsorption capacity of MOF-303(Al) is as high as 19.7 mmol g^-1 at 25.0 °C and 1.0 bar, and the NH₃ capture is fully reversible and no clear loss of capture capacity is observed after 20 cycles of adsorption-desorption. Various spectral studies verify that the superior NH₃ capacity and excellent recyclability of MOF-303(Al) are mainly attributed to the hydrogen bonding interactions of NH₃ with multiple sites of MOF-303(Al).

MOFs industrialization: a complete assessment of production costs

The potential of safe and low-cost batch production processes for Metal-Organic Frameworks (MOFs) at an industrial scale has been evaluated based on the prototypical MOF MIL-160(Al), a bio-derived material of high practical interest that can be made with a high space-time yield using green ambient pressure conditions. A simple method to calculate the production cost of this material has been determined based on a simulated process constructed with the data collected from laboratory pilot large-scale tests taking into account for the first time in MOF cost evaluation all the process parameters such as the scale, the cost of the raw materials, recirculation, and washing. The investment for a production plant established the ground for the estimation of the complete cost. The expected cost ranged from ca. 55 $ per kg at 100 tons per year down to 29.5 $ per kg for 1 kton per year production with longer term perspectives of reaching costs below 10 $ per kg once the bio-derived ligand is considered for the large-scale production of bioplastics.

MIL-160 as an Adsorbent for Atmospheric Water Harvesting

Nowadays, the rapidly growing population, climate change, and environment pollution put heavy pressure on fresh water resources. The atmosphere is the immense worldwide and available water source. The Adsorptive Water Harvesting from the Atmosphere (AWHA) method is considered a promising alternative to desalination technologies for remote arid regions. The development of novel adsorbents with advanced water-adsorption properties is a prerequisite for practical realization of this method. Metal–organic frameworks (MOFs) are a novel class of porous crystalline solids that bring a great potential for AWHA due to their extremely high specific surface area, porosity, and tailored adsorption properties. This work addresses MIL-160 as a water adsorbent for AWHA. The water-adsorption equilibrium of MIL-160 was studied by volumetric method, the isosteric heat of adsorption was calculated, and finally, the potential of MIL-160 for AWHA was evaluated for climatic conditions of the deserts of Saudi Arabia, Mongolia, the Sahara, Atacama, and Mojave as reference arid regions. MIL-160 was shown to ensure a maximum specific water productivity of 0.31–0.33 gH2O/gads per cycle. High fractions of water extracted (0.90–0.98) and collected (0.48–0.97) could be achieved at a regeneration temperature of 80 °C with natural cooling of the condenser by ambient air. The specific energy consumption for water production varied from 3.5 to 6.8 kJ/g, which is acceptable if solar heat is used to drive the desorption. The AWHA method employing MIL-160 is a promising way to achieve a fresh water supply in remote arid areas.

Active Nanointerfaces Based on Enzyme Carbonic Anhydrase and Metal-Organic Framework for Carbon Dioxide Reduction

Carbonic anhydrases are enzymes capable of transforming carbon dioxide into bicarbonate to maintain functionality of biological systems. Synthetic isolation and implementation of carbonic anhydrases into membrane have recently raised hopes for emerging and efficient strategies that could reduce greenhouse emission and the footprint of anthropogenic activities. However, implementation of such enzymes is currently challenged by the resulting membrane’s wetting capability, overall membrane performance for gas sensing, adsorption and transformation, and by the low solubility of carbon dioxide in water, the required medium for enzyme functionality. We developed the next generation of enzyme-based interfaces capable to efficiently adsorb and reduce carbon dioxide at room temperature. For this, we integrated carbonic anhydrase with a hydrophilic, user-synthesized metal–organic framework; we showed how the framework’s porosity and controlled morphology contribute to viable enzyme binding to create functional surfaces for the adsorption and reduction of carbon dioxide. Our analysis based on electron and atomic microscopy, infrared spectroscopy, and colorimetric assays demonstrated the functionality of such interfaces, while Brunauer–Emmett–Teller analysis and gas chromatography analysis allowed additional evaluation of the efficiency of carbon dioxide adsorption and reduction. Our study is expected to impact the design and development of active interfaces based on enzymes to be used as green approaches for carbon dioxide transformation and mitigation of global anthropogenic activities.

Defective Zr-Fumarate MOFs Enable High-Efficiency Adsorption Heat Allocations

Adsorption-driven heat transfer devices incorporating an efficient "adsorbent-water" working pair are attracting great attention as a green and sustainable technology to address the huge global energy demands for cooling and heating. Herein, we report the improved heat transfer performance of a defective Zr fumarate metal-organic framework (MOF) prepared in a water solvent (Zr-Fum HT). This material exhibits an S-shaped water sorption isotherm (P/P₀ = 0.05-0.2), excellent working capacity (0.497 mL_H2O mL^-1_MOF) under adsorption-driven cooling/chiller working conditions (T_{adsorption(ads)} = 30 °C, T_{condensation (con)} = 30 °C, and T_{desorption(des)} = 80 °C), very high coefficient of performances for both cooling (0.83) and heating (1.76) together with a relatively low driving temperature at 80 °C, a remarkable heat storage capacity (423.6 kW h m^-3_MOF), and an outstanding evaporation heat (343.8 kW h m^-3_MOF). The level of performance of the resultant Zr-Fum HT MOF is above those of all existing benchmark water adsorbents including MOF-801 previously synthesized in the N,N-dimethylformamide solvent under regeneration at 80 °C which is accessible from the solar source. This is coupled with many other decisive advantages including green synthesis and high proven chemical and mechanical robustness. The microscopic water adsorption mechanism of Zr-Fum HT at the origin of its excellent water adsorption performance was further explored computationally based on the construction of an atomistic defective model online with the experimental data gained from a subtle combination of characterization techniques.

Rational design of a robust aluminum metal-organic framework for multi-purpose water-sorption-driven heat allocations

Adsorption-driven heat transfer technology using water as working fluid is a promising eco-friendly strategy to address the exponential increase of global energy demands for cooling and heating purposes. Here we present the water sorption properties of a porous aluminum carboxylate metal-organic framework, [Al(OH)(C₆H₃NO₄)]·nH₂O, KMF-1, discovered by a joint computational predictive and experimental approaches, which exhibits step-like sorption isotherms, record volumetric working capacity (0.36 mL mL⁻¹) and specific energy capacity (263 kWh m⁻³) under cooling working conditions, very high coefficient of performances of 0.75 (cooling) and 1.74 (heating) together with low driving temperature below 70 °C which allows the exploitation of solar heat, high cycling stability and remarkable heat storage capacity (348 kWh m⁻³). This level of performances makes this porous material as a unique and ideal multi-purpose water adsorbent to tackle the challenges of thermal energy storage and its further efficient exploitation for both cooling and heating applications.

Adsorption-based heat transfer devices are attractive for clean energy resources, but those using water as the working fluid require suitable water adsorbents. Here the authors use computation and experiment to develop an aluminum-based metal-organic framework adsorbent for adsorption-driven heat transfer devices.

Water and Metal-Organic Frameworks: From Interaction toward Utilization

The steep stepwise uptake of water vapor and easy release at low relative pressures and moderate temperatures together with high working capacities make metal-organic frameworks (MOFs) attractive, promising materials for energy efficient applications in adsorption devices for humidity control (evaporation and condensation processes) and heat reallocation (heating and cooling) by utilizing water as benign sorptive and low-grade renewable or waste heat. Emerging MOF-based process applications covered are desiccation, heat pumps/chillers, water harvesting, air conditioning, and desalination. Governing parameters of the intrinsic sorption properties and stability under humid conditions and cyclic operation are identified. Transport of mass and heat in MOF structures, at least as important, is still an underexposed topic. Essential engineering elements of operation and implementation are presented. An update on stability of MOFs in water vapor and liquid systems is provided, and a suite of 18 MOFs are identified for selective use in heat pumps and chillers, while several can be used for air conditioning, water harvesting, and desalination. Most applications with MOFs are still in an exploratory state. An outlook is given for further R&D to realize these applications, providing essential kinetic parameters, performing smart engineering in the design of systems, and conceptual process designs to benchmark them against existing technologies. A concerted effort bridging chemistry, materials science, and engineering is required.

Microporous Elastomer Filter Coated with Metal Organic Frameworks for Improved Selectivity and Stability of Metal Oxide Gas Sensors

Despite various advantages and usefulness of semiconductor metal oxide gas sensors, low selectivity and humidity interference have limited their practical applications. In order to resolve these issues, we propose a new concept of a selective gas filtering structure that increases the gas selectivity and decreases the moisture interference of metal oxide gas sensors by coating metal organic frameworks (MOFs) on a microporous elastomer scaffold. Cu(BTC) with an excellent selective adsorption capacity for carbon monoxide (CO) compared to hydrogen (H₂) and MIL-160 with an excellent moisture adsorption capacity were uniformly coated on the microporous polydimethylsiloxane (PDMS) structure through a squeeze coating method, resulting in a high content of MOFs with a large effective surface area. A Cu(BTC)-coated microporous PDMS filter showed an excellent adsorption efficiency (62.4%) for CO, thereby dramatically improving the selectivity of H₂/CO by up to 2.6 times. In addition, an MIL-160 coated microporous PDMS filter showed a high moisture adsorption efficiency (76.2%).

Overcoming Crystallinity Limitations of Aluminium Metal-Organic Frameworks by Oxalic Acid Modulated Synthesis

A modulated synthesis approach based on the chelating properties of oxalic acid (H2 C2 O4 ) is presented as a robust and versatile method to achieve highly crystalline Al-based metal-organic frameworks. A comparative study on this method and the already established modulation by hydrofluoric acid was conducted using MIL-53 as test system. The superior performance of oxalic acid modulation in terms of crystallinity and absence of undesired impurities is explained by assessing the coordination modes of the two modulators and the structural features of the product. The validity of our approach was confirmed for a diverse set of Al-MOFs, namely X-MIL-53 (X=OH, CH3 O, Br, NO2 ), CAU-10, MIL-69, and Al(OH)ndc (ndc=1,4-naphtalenedicarboxylate), highlighting the potential benefits of extending the use of this modulator to other coordination materials.

Probing the limits of linker substitution in aluminum MOFs through water vapor sorption studies: mixed-MOFs instead of mixed-linker CAU-23 and MIL-160 materials

Only water vapor sorption isotherms were able to reveal the mixed-MOF instead of mixed-linker material formation of CAU-23 and MIL-160.

Metal-Organic Framework-Based Composite for Photocatalytic Detection of Prevalent Pollutant

Photocatalytic properties of 2,5-furandicarboxylic acid (FDCA), a model organic molecule used for biopolymer production, are reported for the first time. Further integration of FDCA into metal-organic framework (MOF) structures and subsequent silver-based photoactivation leads to the next generation of hybrids with controlled morphologies, capable of forming sensorial platforms for prevalent phenol contaminant detection. The mechanisms that allow photocatalytic functionality are driven by the charge carrier generation in the organic molecule (either in its alone or integrated form) and depend on sample's physical and chemical properties as confirmed by scanning and transmission electron microscopy, Fourier transform infrared and X-ray photoelectron spectroscopy, and X-ray diffraction, respectively. Electrochemical analysis using cyclic voltammetry confirmed high sensitivity for p-nitrophenol (p-NP) detection as dictated by the selective electron migration at a user-controlled electrode interface. Considering the wide usage of p-NP and its increased discharge shown to lead to harmful effects on both the environment and biosystems, this new detection method is envisioned to allow effective control and regulation of such compound release, all under low-cost and environmentally friendly conditions.

A metal-organic framework for efficient water-based ultra-low-temperature-driven cooling

Efficient use of energy for cooling applications is a very important and challenging field in science. Ultra-low temperature actuated (Tdriving < 80 °C) adsorption-driven chillers (ADCs) with water as the cooling agent are one environmentally benign option. The nanoscale metal-organic framework [Al(OH)(C6H2O4S)] denoted CAU-23 was discovered that possess favorable properties, including water adsorption capacity of 0.37 gH2O/gsorbent around p/p0 = 0.3 and cycling stability of at least 5000 cycles. Most importantly the material has a driving temperature down to 60 °C, which allows for the exploitation of yet mostly unused temperature sources and a more efficient use of energy. These exceptional properties are due to its unique crystal structure, which was unequivocally elucidated by single crystal electron diffraction. Monte Carlo simulations were performed to reveal the water adsorption mechanism at the atomic level. With its green synthesis, CAU-23 is an ideal material to realize ultra-low temperature driven ADC devices.

Metal-Organic Frameworks with Potential Application for SO2 Separation and Flue Gas Desulfurization

Sulfur dioxide (SO₂) is an acidic and toxic gas and its emission from utilizing energy from fossil fuels or in industrial processes harms human health and environment. Therefore, it is of great interest to find new materials for SO₂ sorption to improve classic flue gas desulfurization. In this work, we present SO₂ sorption studies for the three different metal-organic frameworks MOF-177, NH₂-MIL-125(Ti), and MIL-160. MOF-177 revealed a new record high SO₂ uptake (25.7 mmol·g^-1 at 293 K and 1 bar). Both NH₂-MIL-125(Ti) and MIL-160 show particular high SO₂ uptakes at low pressures ( p < 0.01 bar) and thus are interesting candidates for the removal of remaining SO₂ traces below 500 ppm from flue gas mixtures. The aluminum furandicarboxylate MOF MIL-160 is the most promising material, especially under application-orientated conditions, and features excellent ideal adsorbed solution theory selectivities (124-128 at 293 K, 1 bar; 79-95 at 353 K, 1 bar) and breakthrough performance with high onset time, combined with high stability under both humid and dry SO₂ exposure. The outstanding sorption capability of MIL-160 could be explained by DFT simulation calculations and matching heat of adsorption for the binding sites O_furan···S_SO2 and OH_Al-chain···O_SO2 (both ∼40 kJ·mol^-1) and O_{furan/carboxylate}···S_SO2 (∼55-60 kJ·mol^-1).

Robust synthesis routes and porosity of the Al-based metal–organic frameworks Al-fumarate, CAU-10-H and MIL-160

We confirm that the investigated Al-MOFs are robust with respect to reproducible synthesis and concomitant porosity as a prerequisite for applications.

Investigating water vapour sorption kinetics of aluminium MOFs by powder X-ray diffraction

The water sorption behaviour of aluminium MOF CAU-10 and CAU-15-Cit was followed by in situ powder X-ray diffraction.

Closed Adsorption Heat Storage—A Life Cycle Assessment on Material and Component Levels

Closed adsorption storages have been investigated in several projects for heat storage in building applications with focus on energy density and performance. This study complements this research with the assessment of the environmental impacts over the life cycle. Global warming potential (GWP) was chosen as the assessment criterion. Selected sorption materials in combination with water as the refrigerant were analyzed first by themselves and then embedded in a generic storage configuration. Sensible storage in water served as the reference benchmark. Results on material and component level showed that the relative storage capacity compared to water under realistic operating conditions reached values of below 4 and 2.5, respectively, in the best cases. Since the effort for producing the sorbents as well as the auxiliary material demand for assembling storage components was significantly higher than in the reference case, the specific environmental impact per storage capacity also turned out to be ~2.5 to ~100 times higher. We therefore suggest focusing sorption storage research on applications that (a) maximize the utilization of the uptake of sorbents, (b) do not compete with water storages, and (c) require minimal auxiliary parts.

User-Tailored Metal-Organic Frameworks as Supports for Carbonic Anhydrase

Carbonic anhydrase (CA) was previously proposed as a green alternative for biomineralization of carbon dioxide (CO₂). However, enzyme's fragile nature when in synthetic environment significantly limits such industrial application. Herein, we hypothesized that CA immobilization onto flexible and hydrated "bridges" that ensure proton-transfer at their interfaces leads to improved activity and kinetic behavior and potentially increases enzyme's feasibility for industrial implementation. Our hypothesis was formulated considering that water plays a key role in the CO₂ hydration process and acts as both the reactant as well as the rate-limiting step of the CO₂ capture and transformation process. To demonstrate our hypothesis, two types of user-synthesized organic metallic frameworks [metal-organic frameworks (MOFs), one hydrophilic and one hydrophobic] were considered as model supports and their surface characteristics (i.e., charge, shape, curvature, size, etc.) and influence on the immobilized enzyme's behavior were evaluated. Morphology, crystallinity and particle size, and surface area of the model supports were determined by scanning electron microscopy, dynamic light scattering, and nitrogen adsorption/desorption measurements, respectively. Enzyme activity, kinetics, and stability at the supports interfaces were determined using spectroscopical analyses. Analysis showed that enzyme functionality is dependent on the support used in the immobilization process, with the enzyme immobilized onto the hydrophilic support retaining 72% activity of the free CA, when compared with that immobilized onto the hydrophobic one that only retained about 28% activity. Both CA-MOF conjugates showed good storage stability relative to the free enzyme in solution, with CA immobilized at the hydrophilic support also revealing increased thermal stability and retention of almost all original enzyme activity even after heating treatment at 70 °C. In contrast, free CA lost almost half of its original activity when subject to the same conditions. This present work suggests that MOFs tunable hydration conditions allow high enzyme activity and stability retention. Such results are expected to impact CO₂ storage and transformation strategies based on CA and potentially increase user-integration of enzyme-based green technologies in mitigating global warming.

Removal of tetracycline from aqueous solution by MOF/graphite oxide pellets: Preparation, characteristic, adsorption performance and mechanism

Tetracycline (TC) as a typical antibiotic has been used extensively and detected in soil, surface water, ground water and drinking water, which results in toxic effect and bacterial resistance. In this study, aluminum-based metal organic framework/graphite oxide (MIL-68(Al)/GO) pellets were prepared through the addition of sodium alginate (SA), a natural crosslinking agent, and applied as a novel adsorbent for aqueous TC removal. The adsorption materials were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), N₂ adsorption-desorption analysis and X-ray photoelectron spectroscopy (XPS). Results demonstrated that the pellets maintained similar chemical structure with parent MIL-68(Al)/GO powder. It is noted that the surface area and total volume of the pellets decreased obviously due to the disappearance of micropores. Besides, the efficiency of MIL-68(Al)/GO pellets for TC removal was evaluated by adsorption properties compared with parent powder, including key influential parameters, and adsorption isotherms, kinetics and mechanisms. It is found that the adsorption process was conformed to pseudo-first-order kinetics model and more suitably described through Langmuir isotherm model, with 228 mg g^-1 of the maximum adsorption capacity. Moreover, these pellets which were separated easily and quickly presented high adsorption capacity and good stability in a wide pH range. The adsorption mechanism of the pellets may be ascribed to the complex interactions of hydrogen bonding, π-π stacking as well as Al-N covalent bonding. Overall, the MIL-68(Al)/GO pellets might be a promising adsorbent and show great potential for the removal of aqueous TC.

Metal-Organic Frameworks as advanced moisture sorbents for energy-efficient high temperature cooling

Latent cooling load accounts for 30% of the total load of air-conditioning, and its proportion is even higher in many tropical and subtropical climates. Traditional vapour-compression air-conditioning (VCAC) has a low coefficient of performance (COP) due to the refrigeration dehumidification process, which often makes necessary a great deal of subsequent re-heating. Technologies using conventional desiccants or sorbents for indoor moisture control are even less competitive than VCAC due to their high regeneration temperature, long cycling time and bulky components. Here, we report a novel high temperature cooling system that uses porous metal-organic frameworks (MOFs) as advanced sorbents for humidity control. We directly coat MOFs on the surface of evaporator and condenser. The system has no additional components compared to a traditional VCAC. The evaporator can simultaneously remove both the sensible and latent loads of the incoming air without reducing the temperature below its dew point. The regeneration of wet MOFs is completely driven by the residual heat from the condenser. The MOF-coated heat exchangers can achieve a cooling power density of 82 W·L⁻¹. We demonstrate that the system has a high COP, up to 7.9, and can save 36.1% of the energy required, compared to the traditional VCAC system with reheating. The amphiphilic MOFs used in the research have high water uptake, are made of low-cost raw materials and have high hydrothermal stability. They thus have the potential for being scaled up for large-scale applications in air conditioning.