Development of a sol-gel enzyme inhibition-based amperometric biosensor for cyanide

HRP/[Zn–Cr–ABTS] redox clay-based biosensor: design and optimization for cyanide detection

A novel inexpensive and simple amperometric biosensor, based on the immobilization of HRP into redox active [Zn-Cr-ABTS] layered double hydroxide, is applied to the determination of cyanide. The electrochemical transduction step corresponds to the reduction at 0.0 V of ABTS+* enzymatically formed in the presence of H2O2. The biosensor has a fast response to H2O2 (8s) with a linear range of 1.7 x 10(-9) to 2.1 x 10(-6) M and a sensitivity of 875 mA M(-1) cm(-2). The apparent Michaelis-Menten constant (KMapp) is 12 microM. The detection of cyanide is performed via its non competitive inhibiting action on the HRP/[Zn-Cr-ABTS] electrode. The concentration range of the linear response and the apparent inhibition constant (ki) are 5 x 10(-9) to 4 x 10(-8) and 1.4 x 10 (-7) M, respectively.

Semi-quantitative "spot-test" of cyanide

A selective, sensitive, rapid and simple-handling analytical method for the determination of cyanide at low detection limits in surface and underground water, soil and industrial waste samples was developed. The method is based on a reaction, proposed by Guilbault and Kramer, where free cyanide reacts with p-nitrobenzaldehyde to form an intermediate cyanohydrin, which reacts with o-dinitrobenzene to give a highly colored purple compound. The original procedure was modified for application in a small device containing a gas-permeable membrane. The cyanide is converted in the volatile hydrogen cyanide, which permeates through a PTFE membrane, reaching colorimetric reagents. In order to obtain semi-quantitative results, printed color scales were built. The method allows rapid, accurate, selective, low-cost and simple-handling determinations of free cyanide, even in complex samples. About 150 real samples were analyzed. Less than 10 ng of free cyanide per ml (10 microg l(-1)) can be easily detected. For more concentrated solutions, the results had been compared to those obtained using differential pulse polarography. The standard addition method was used for more diluted solutions.

Comparison of photovoltaic behaviors for horseradish peroxidase and its mimicry by surface photovoltage spectroscopy

Surface photovoltage spectroscopy (SPS) was chosen to study the photovoltaic behavior of horseradish peroxidase (HRP), hemin and immobilized hemin (poly(NIPAAm/MBA/hemin)). Different photovoltaic behaviors were observed in these three systems. In air, similar SPS curves were found for HRP and poly(NIPAAm/MBA/hemin) with different response intensities. However, poly(NIPAAm/MBA/hemin) showed a wider changing range upon increasing the positive and negative bias to 1.0 V. The SPS of hemin showed a total different behavior when an external positive potential was applied. In vacuum, clearly different photovoltaic behaviors were found. Moreover, the response value decreased when HRP was exposed to O2, the SPS intensity was different from that in air, and could be altered by changing the external biases. On the other hand, the SPS could not be changed before and after poly(NIPAAm/MBA/hemin) was exposed to O2. These differences may result from different chemical microenvironments for hemin in HRP versus that in poly(NIPAAm/MBA/hemin). It could be concluded that H2O and O2 were important factors affecting the photovoltage response in HRP, but only H2O played this important role in poly(NIPAAm/MBA/hemin).

Bioencapsulation within synthetic polymers (Part 1): sol-gel encapsulated biologicals

Since its inception a decade ago, sol-gel encapsulation has opened up an intriguing new way to immobilize biological materials. An array of substances, including catalytic antibodies, DNA, RNA, antigens, live bacterial, fungal, plant and animal cells and whole protozoa, have been encapsulated in silica, metal-oxide, organosiloxane and hybrid sol-gel polymers. The advantages of these 'living ceramics' might give them applications as optical and electrochemical sensors, diagnostic devices, catalysts, and even bioartificial organs. With rapid advances in sol-gel precursors, nanoengineered polymers, encapsulation protocols and fabrication methods, this technology promises to revolutionize bioimmobilization.